Carbon-coated ZnFe2O4 spheres with sizes of ~110–180 nm anchored on graphene nanosheets (ZF@C/G) are successfully prepared and applied as anode materials for lithium ion batteries (LIBs). The obtained ZF@C/G presents an initial discharge capacity of 1235 mAh g?1 and maintains a reversible capacity of 775 mAh g?1 after 150 cycles at a current density of 500 mA g?1. After being tested at 2 A g?1 for 700 cycles, the capacity still retains 617 mAh g?1. The enhanced electrochemical performances can be attributed to the synergetic role of graphene and uniform carbon coating (~3–6 nm), which can inhibit the volume expansion, prevent the pulverization/aggregation upon prolonged cycling, and facilitate the electron transfer between carbon-coated ZnFe2O4 spheres. The electrochemical results suggest that the synthesized ZF@C/G nanostructures are promising electrode materials for high-performance lithium ion batteries.
One-dimensional Ce3+-doped Li4Ti5O12 (Li4Ti5?xCexO12, x?=?0, 0.01, 0.02, and 0.05) sub-microbelts with the width of approximately 500 nm and thickness of about 200 nm have been synthesized via the facile electrospinning method. The structure and morphology of the as-prepared samples are characterized by XRD, TEM, SEM, BET, HRTEM, XPS, and AFM. Importantly, one-dimensional Li4Ti5O12 sub-microbelts can be well preserved with the introduction of Ce3+ ions, while CeO2 impurity is obtained when x is greater than or equal to 0.02. The comparative experiments prove that Ce3+-doped Li4Ti5O12 electrodes exhibit the brilliant electrochemical performance than undoped counterpart. Particularly, the reversible capacity of Li4Ti4.98Ce0.02O12 electrode reaches up to 139.9 mAh g?1 and still maintains at 132.6 mAh g?1 even after 100 cycles under the current rate of 4 C. The superior lithium storage properties of Li4Ti4.98Ce0.02O12 electrode could be attributed to their intrinsic structure advantage as well as enhanced overall conductivity.
The Br-doped hollow TiO2 photocatalysts were prepared by a simple hydrothermal process on the carbon sphere template following with calcination at 400 °C. The structure and properties of photocatalysts were characterized by X-ray diffraction, Raman spectrum, scanning electron microscope, transmission electron microscopy, N2 desorption–adsorption, UV–Vis spectroscopy, and X-ray photoelectron spectroscopy. The TiO2 hollow spheres are in diameter of 500 nm with shell thickness of 50 nm. The shell is composed of small anatase nanoparticles with size of about 10 nm. The TiO2 hollow spheres exhibit high crystalline and high surface area of 89.208 m2/g. With increasing content of Br doping, the band gap of TiO2 hollow spheres decreased from 2.85 to 1.75 eV. The formation of impurity band in the band gap would narrow the band gap and result in the red shift of absorption edge from 395 to 517 nm, which further enhances the photocatalytic activity. The appropriate Br doping improves the photocatlytic activity significantly. The TiO2 hollow spheres with 1.55% Br doping (0.5Br-TiO2) exhibit the highest photocatalytic activity under full light. More than 98% of RhB, MO, and MB can be photodegraded using 0.5Br-TiO2 with concentration of 10 mg/L in 40, 30, and 30 min, respectively. The degradation rate of Br-doped photocatalysts was 40% faster than undoped ones.
This paper reported a one-step synthesis of Ag2S/Ag@MoS2 nanocomposites and its applications in the surface-enhanced Raman scattering (SERS) detection and photocatalytic degradation of organic pollutants. The nanocomposites were well characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), cyclic voltammograms (CV), the Brunauer-Emmett-Teller (BET), and Fourier transforms infrared spectra (FTIR). The AgNPs were uniformly dispersed on the MoS2 nanosheets and the particle size of the AgNPs was about 10–30 nm. These Ag2S/Ag@MoS2 nanocomposites offered sensitive SERS signals for the detection of R6G with the limit of detections as low as 10?10 M. The photocatalytic activity of the composite catalyst was studied by the degradation of methylene blue (MB) dye under light illumination. The apparent rate constant of MB degradation for the obtained catalyst could reach 6.6?×?10?2 min?1, indicating that the novel Ag2S/Ag@MoS2 nanocomposites can be explored for organic pollutant’s detection and degradation.
In the synthesis of nanostructures by pulsed laser deposition (PLD), a crucial role is played by the environmental deposition pressure and the substrate temperature. Due to the high temperature of nanoparticles (NPs) at landing, other factors may determine the structure of the resulting aggregates. Here, Au and TiO2 nanostructures are obtained by non-thermal fs-PLD in ambient conditions. On Si(100), only TiO2 NPs form fractals with areas up to ~ 1 × 106 nm2, while on quartz Au NPs also form fractals with areas up to ~ 5 × 103 nm2, a much smaller size with respect to the TiO2 case. The aggregation is described by a simple diffusive model, taking into account isotropic diffusion of the NPs, allowing quantitative simulations of the NPs and fractal area. The results highlight the key role of substrate thermal conductivity in determining the formation of fractals.
Carbon materials have attracted great attention in CO2 capture and energy storage due to their excellent characteristics such as tunable pore structure, modulated surface properties and superior bulk conductivities, etc. Biomass, provided by nature with non-toxic, widespread, abundant, and sustainable advantages, is considered to be a very promising precursor of carbons for the view of economic, environmental, and societal issues. However, the preparation of high-performance biomass-derived carbons is still a big challenge because of the multistep process for their synthesis and subsequent activation. Herein, hierarchically porous structured carbon materials have been prepared by directly carbonizing dried cauliflowers without any addition of agents and activation process, featuring with large specific surface area, hierarchically porous structure and improved pore volume, as well as suitable nitrogen content. Being used as a solid-state CO2 adsorbent, the obtained product exhibited a high CO2 adsorption capacity of 3.1 mmol g?1 under 1 bar and 25 °C and a remarkable reusability of 96.7% retention after 20 adsorption/regeneration cycles. Our study reveals that choosing a good biomass source was significant as the unique structure of precursor endows the carbonized product with abundant pores without the need of any post-treatment. Used as an electrode material in electrochemical capacitor, the non-activated porous carbon displayed a fairly high specific capacitance of 228.9 F g?1 at 0.5 A g?1 and an outstanding stability of 99.2% retention after 5000 cycles at 5 A g?1.
Graphical abstract Hierarchically porous structured carbon materials are prepared by directly carbonizing dried cauliflower without any agents and process of activation for high performance of CO2 capture and capacitor.
This work reported a novel kind of CdTe quantum dot (QD) decorated mesoporous SiO2 (m-SiO2/QD) hybrid hollow nanoparticles for carrying photodynamic therapy (PDT) reagent. Both rod-like and spherical nanoparticles were prepared by using different shaped templates. Due to the porous shell and hollow interior, the hybrid m-SiO2/QD hollow nanorod with 360 nm long and 120 nm in diameter was selected for carrying zinc(II) phthalocyanine (ZnPc) photosensitizing molecules (61 mg/g) since the generated reactive 1O2 could be easily delivered out of the hollow particles through the porous shell (BET area 251 cm2/g). It was found that the m-SiO2/QD-ZnPc hollow nanorods exhibited a good PDT activity and showed effective photocytotoxicity for the cancer cells. Because of the porous nature, fluorescence characteristic, and excellent storage ability, the m-SiO2/QD hybrid hollow particles possessed broad potential in the fluorescent labeled PDT.
Graphic abstract m-SiO2/QD hybrid hollow particles with different morphologies could be successfully synthesized by using the templating method and they could be used as carriers for photodynamic therapy reagents.
Mo-doped V2O5 hierarchical nanorod/nanoparticle core/shell porous microspheres (MVHPMs) were prepared via a simple hydrothermal approach using ammonium metavanadate and ammonium molybdate as precursors followed by a thermal annealing process. The samples were characterized by XRD, SEM, TEM, EDS, and XPS carefully; it confirmed that porous microspheres with uniform Mo doping in the V2O5 matrix were obtained, and it contains an inner core self-assembled with 1D nanorods and outer shell consisting of nanoparticles. A plausible growth mechanism of Mo-doped V2O5 (Mo-V2O5) porous microspheres is suggested. The unique microstructure made the Mo-V2O5 hierarchical microspheres a good cathode material for Li-ion battery. The results indicate the synthesized Mo-V2O5 hierarchical microspheres exhibit well-improved electrochemical performance compared to the undoped samples. It delivers a high initial reversible capacity of 282 mAh g?1 at 0.2 C, 208 mAh g?1 at 2 C, and 111 mAh g?1 at 10 C, and it also exhibits good cycling stabilities; a capacity of 144 mAh g?1 is obtained after 200 cycles at 6 C with a capacity retention of >?82%, which is much high than that of pure V2O5 (95 mAh g?1 with a capacity retention of 72%).
Addition reaction between C60 and ethylenediamine occurred at room temperature in an ambient condition. C60-ethylenediamine adduct particles were prepared by mixing toluene solutions of C60 and ethyelenediamine. Average diameter of the C60-ethylenediamine adduct particles was changed non-linearly according to the reaction time, which were observed using transmission electron microscopy. Early stage of the reaction, the diameter of the adduct particles was changed from about 250 to about 430 nm. Then, the size of the adduct particles was converged to about 300 nm. During this addition reaction, the crystalline sizes of adduct particles were constant about 2–3 nm, regardless of the sizes of the adduct particles, which were determined by X-ray diffraction measurement.
Solution combustion synthesis (SCS) is an effective and rapid method for synthesizing nanocrystalline materials. However, the control over size, morphology, and microstructure are rather limited in SCS. Here, we develop a novel ultrasonic-assisted solution combustion route to synthesize the porous and nano-sized Na3V2(PO4)3/C composites, and reveal the effects of ultrasound on the structural evolution of NVP/C. Due to the cavitation effects generated from ultrasonic irradiation, the ultrasonic-assisted SCS can produce honeycomb precursor, which can be further transformed into porous Na3V2(PO4)3/C with reticular and hollow structures after thermal treatment. When used as cathode material for Na-ion batteries, the porous Na3V2(PO4)3/C delivers an initial discharge capacity of 118 mAh g?1 at 0.1 C and an initial coulombic efficiency of 85%. It can retain 93.8% of the initial capacity after 120 cycles at 0.2 C. The results demonstrate that ultrasonic-assisted SCS can be a new strategy to design crystalline nanomaterials with tunable microstructures.
Graphical abstract Porous and nano-sized Na3V2(PO4)3/C composites with reticular and hollow structures are synthesized by an ultrasonic-assisted solution combustion route due to the cavitation effects, and exhibit excellent electrochemical performance as cathode in sodium ion battery.
Asymmetric capacitor based on TiO2 with the size range from 90 to 410 nm and mesoporous MnO2 (ca. 200–380 nm) electrodes has been successfully constructed and characterized in LiClO4 aqueous electrolyte. The samples of both metal oxides were fully characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray analysis (EDX), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), N2 adsorption-desorption, and so on. The electrochemical capacitive performances of both electrode materials were evaluated by cyclic voltammetry and galvanostatic charge-discharge in 1 mol/L LiClO4 with a working voltage of 2.0 V. The discharge profile of the asymmetric capacitor exhibited an excellent capacitive behavior and good cycling stability after 2000 cycles. Moreover, the TiO2//MnO2 asymmetric capacitor possesses both higher energy density and power density (7.7 Wh/kg, 762.5 W/kg) than that of Maxsorb//Maxsorb symmetrical capacitor (7.0 Wh/kg, 400.0 W/kg).
Graphical abstract A novel asymmetric capacitor based on TiO2 and mesoporous MnO2 electrodes has been successfully constructed and characterized in LiClO4 aqueous electrolyte.
This study describes the synthesis method of water-soluble, low-toxicity, photostable highly luminescent probes based on I–III–VI2 type semiconductor quantum dots (QDs) and the possibility of tumor targeting in living animals. Cd-free high-quality CuInS2/ZnS core/shell QDs were synthesized, and their surfaces were reacted with mercaptoundecanoic acid for aqueous phase transfer followed by reaction with glycol-chitosan; lastly, Arg-Gly-Asp (RGD) integrin-binding peptide was covalently attached for in vivo tumor targeting. Dowtherm A, a highly viscous heat-transfer organic fluid, was used to control semiconductor crystal growth at high temperature (>230 °C) during organic synthesis. The structural and optical properties of the resulting CuInS2/ZnS QDs were investigated. The average diameters of CuInS2 and CuInS2/ZnS QDs were 3.0 and 3.7 nm, respectively. Cell toxicity and in vivo tumor targetability in RR1022 cancer cell-xenografted mice were further evaluated using cRGDyk-tagged glycol-chitosan-coated CuInS2/ZnS QDs. Glycol-chitosan-coated MUA-QDs displayed a Z-average diameter of 203.8 ± 7.67 nm in water by dynamic light scattering.
Previous studies on the fate of engineered nanoparticles (ENPs) incorporated in paints mainly focused on the release of the particles as affected by a limited number of factors or monitoring their release from natural sources. In this study, the effects of four factors (i.e., weathering duration, water pH, rainfall duration and intensity) were investigated on the release of SiO2-ENPs, Ag-ENPs, and TiO2-ENPs from paints applied on panels. The static water immersion test showed that the concentrations of studied particles all increased with weathering duration. At low and high pH, SiO2-ENPs and Ag-ENPs showed a higher release, while the release of TiO2-ENPs was relatively high at low pH. With increased simulated rainfall duration, the concentration released decreased for Si, and the opposite was observed for Ag, while no obvious correlation was noted for Ti. With greater rainfall intensity, there was increasing release of all particles. In total, the releases of Ag-ENPs and TiO2-ENPs were extremely low and within the level of 21.32–42.16 μg L?1and 0.6–2.3 μg L?1, respectively, while the values for SiO2-ENPs were in the range of 7.5–12 mg L?1. Additionally, microscopic results highlighted that SiO2-ENPs were mainly released in the form of agglomerates, and only a small fraction was below 0.1 μm. Considering these influence factors together, conclusions may be made that weathering time and rainfall duration are more important in controlling release than water pH.
Sm3+-doped SrSnO3 (SrSnO3:Sm3+) nanopowders were synthesized by a simple hydrothermal method and followed by a heat treatment process. The as-synthesized nanopowders were assembled in dye-sensitized solar cells (DSSCs) to investigate their photoelectric properties. X-ray diffraction (XRD), scanning electron microscope (SEM), and energy-dispersive spectrometer (EDS) confirmed the formation of SrSnO3:Sm3+ nanopowders with perovskite structure. The ultraviolet-visible absorption spectra and photoluminescence spectra indicate a down-conversion from ultraviolet light to visible light which matches the strong absorption region of the N719 dye. The DSSC based on SrSnO3:Sm3+ photo-anode improved its photoelectric conversion efficiency (η) via the down-conversion of doped Sm3+. Under the irradiation of the simulated sunlight with 100 mW/cm2, the DSSC based on SrSnO3 doping with Sm3+ of 0.6 wt% showed the highest η of 1.54%, which improved 71.11% compared with the DSSC based on pure SrSnO3.
A facile and efficient one-pot method for the synthesis of well-dispersed hollow CuFe2O4 nanoparticles (H-CuFe2O4 NPs) in the presence of cellulose nanocrystals (CNC) as the support was described. Based on the one-pot solvothermal condition control, magnetic H-CuFe2O4 NPs were in-situ grown on the CNC surface uniformly. TEM images indicated good dispersity of H-CuFe2O4 NPs with uniform size of 300 nm. The catalytic activity of H-CuFe2O4/CNC was tested in the catalytic reduction of 4-nitrophenol (4-NP) in aqueous solution. Compared with most CNC-based ferrite catalysts, H-CuFe2O4/CNC catalyst exhibited an excellent catalytic activity toward the reduction of 4-NP. The catalytic performance of H-CuFe2O4/CNC catalyst was remarkably enhanced with the rate constant of 3.24 s?1 g?1, which was higher than H-CuFe2O4 NPs (0.50 s?1 g?1). The high catalytic activity was attributed to the introduction of CNC and the special hollow mesostructure of H-CuFe2O4 NPs. In addition, the H-CuFe2O4/CNC catalyst promised good conversion efficiency without significant decrease even after 10 cycles, confirming relatively high stability. Because of its environmental sustainability and magnetic separability, H-CuFe2O4/CNC catalyst was shown to indicate that the ferrite nanoparticles supported on CNC were acted as a promising catalyst and exhibited potential applications in numerous ferrite based catalytic reactions.
In this study, the magnetically recyclable Fe3O4@C/BiOBr heterojunction with enhanced visible light-driven photocatalytic ability was obtained by two-step solvothermal method. The phase, morphology, and structure of the samples were investigated by XRD, FESEM, HRTEM, and XPS. The Fe3O4@C/BiOBr heterojunction was composed of Fe3O4@C sphere and BiOBr microsphere with diameters of 200 nm and 1000 nm, respectively. The photocatalytic performance of Fe3O4@C/BiOBr composite for RhB was examined under visible light irradiation. The photocatalytic activity of Fe3O4@C/BiOBr composite was much higher than that of pure BiOBr and Fe3O4@C. After 35 min of irradiation, 97% of RhB could be removed with the Fe3O4@C/BiOBr photocatalyst. Based on radical trapping experiments of active species, the mechanism of enhanced photocatalytic performance was proposed. In addition, the superparamagnetic property of the photocatalyst not only allows its easy recyclability by an external magnetic field but also maintains high photocatalytic activity after five cyclic experiments.
Molybdenum disulfide hybridized with graphene nanoribbon (MoS2/GNR) was prepared by mild method. MoS2/GNR hybrids interlace loosely into a three-dimension structure. GNR hybridization can improve the dispersity of MoS2, reduce the grain size of MoS2 to 3–6 nm, increase the specific surface area, and broaden the interlamellar spacing of MoS2 (002) plane to 0.67–0.73 nm, which facilitates the transportation of Li+ ions for lithium-ion battery. MoS2/GNR hybrids have better cyclic durability, higher specific discharge capacity, and superior rate performance than MoS2. The electrocatalytic activity in hydrogen evolution reaction shows that MoS2/GNR hybrids have the lower overpotential and the larger current density with a negligible current loss after 2000 cycles. Hybridizing with GNRs enhances both the lithium-ion electrochemical storage and the electrocatalytic activity of MoS2.
Graphical abstract MoS2/GNR hybrid prepared by a mild method is interlaced loosely into a three-dimension structure. Superior electrochemical performances of MoS2/GNR hybrids than MoS2 have been highlighted for the potential application for long- term durability energy-storage devices and HER electrocatalytic materials.
Spinel ferrites can be used in magnetic targeting and microwave heating and can therefore be used for targeted and controllable drug delivery. We used the cetyltrimethylammonium bromide-assisted solvothermal method to synthesize a series of spinel ferrites (MxFe3-xO4, M=Mg, Mn, Fe, Co, Ni, Cu, Zn) with a mesoporous or hollow-mesoporous structure suitable for direct drug loading and the particle diameters ranging from 200 to 350 nm. We investigated the effects of M2+ cation on the morphology and properties of these products by analyzing their transmission electron microscopy images, mesoporous properties, magnetic properties, and microwave responses. We chose hollow-mesoporous MxFe3-xO4 (M=Fe, Co, Zn) nanoparticles, which had better overall properties, for the drug VP16 (etoposide) loading and microwave-controlled release. The CoxFe3-xO4 and Fe3O4 particles trapped 61.5 and 64.8%, respectively, of the VP16, which were higher than that (60.4%) of ZnxFe3-xO4. Controllable drug release by these simple magnetic nanocarriers can be achieved by microwave irradiation, and VP16-loaded CoxFe3-xO4 released the most VP16 molecules (more than 50% after 1 h and 69.1% after 6 h) under microwave irradiation. Our results confirm the favorable drug loading and microwave-controlled delivery by these ferrites, and lay a theoretical foundation to promote clinical application of the targeted controllable drug delivery system.
Graphical abstract In the present study, we prepared mesoporous or hollow-mesoporous spinel ferrites (MxFe3-xO4, M=Mg, Mn, Fe, Co, Ni, Cu, Zn) by CTAB-assisted solvothermal method and solved the problem of Cu and Ni impurities in CuxFe3-xO4 and NixFe3-xO4 products by means of magnetic separation and additional redox reactions, respectively. We investigated the effects of the M2+ cation on the morphology, mesoporous properties, magnetic properties, and microwave responses of these ferrites. Then, the drug loading and microwave-controlled drug release of hollow-mesoporous MxFe3-xO4 (M?=?Fe, Co, Zn) nanoparticles with better overall properties were also studied. CoxFe3-xO4 has the best overall performances for microwave-controlled drug release.
Ligand-free palladium nanoparticles supported on multi-walled carbon nanotubes (Pd/MWCNT) were prepared by the supercritical carbon dioxide (scCO2) deposition method using a novel scCO2-soluble Pd organometallic complex as a precursor. The precursor with the perfluoroalkyl chain group was synthesized and identified by microanalytic methods. The deposition was carried out at the temperature of 363.15 K and pressure of 27.6 MPa CO2. The prepared metallic nanoparticles were obtained with an average size of 2 nm. Pd/MWCNT was utilized as a heterogeneous catalyst in Suzuki cross-coupling reaction. The nanocatalyst was found very effective in Suzuki reaction and it could also be recovered easily from the reaction media and reused over several cycles without significant loss of catalytic activity under mild conditions.
Graphical Abstract Pd/MWCNT was prepared by the scCO2 deposition method using a new synthesized perfluroalkylated vic-dioxime Pd complex as the precursor. The prepared nanoparticle was very effective as catalyst and reusable for Suzuki cross coupling reaction under mild conditions.
Carbon-based nanoparticles (NPs) such as fullerenes and nanotubes have been extensively studied for drug delivery in recent years. The permeation process of fullerene and its derivative molecules through membrane is essential to the utilization of fullerene-based drug delivery system, but the mechanism and the dynamics of permeation through cell membrane are still unclear. In this study, coarse-grained molecular dynamics simulations were performed to investigate the permeation process of functionalized fullerene molecules (ca. 0.72 nm) through the membrane. Our results show that single functionalized fullerene molecule in such nanoscale could permeate the lipid membrane in micro-second time scale. Pristine C60 molecules prefer to aggregate into several small clusters while C60OH15 molecules could aggregate into one big cluster to permeate through the lipid membrane. After permeation of C60 or its derivatives into membrane, all C60 and C60OH15 molecules disaggregated and monodispersed in the lipid membrane.
