用模板法制备TiO2纳米线阵列膜及光催化性能的研究

用溶胶-凝胶技术在多孔阳极氧化铝模板的有序微孔内制备了高度取向的TiO2纳米线阵列膜光催化剂.用XRD,AFM和SEM等手段对样品进行了表征.结果表明,TiO2纳米线阵列膜晶型为锐钛矿,从AFM图像中可以看出TiO2纳米线线径分布均匀一致,取向性极好,直径与AAO模板的孔径大小一致.以其对吖啶橙的降解效果作为评价光催化活性的标准,与相同条件下制备的TiO2/玻璃膜相比,TiO2纳米线阵列膜具有很好的催化活性.     

TiO2/PtO-Pt复合膜和SnO2/PtO-Pt复合膜氢敏性能的研究

将PtO-Pt纳米粒子膜与TiO2，SnO2纳米粒子膜复合，利用PtO-Pt纳米粒子膜作 为插入电极和催化剂，设计并研制出一类新型双层结构复合膜气体传感器。采用 TEM和SEM对薄膜的显微结构进行了表征，对空气中4.0H2的氢敏性能研究表明： 200℃时，TiO2/PtO-Pt复合膜对氢气的灵敏度为70％，而TiO2纳米粒子膜无响应。 100℃时，SnO2/PtO-Pt复合膜的灵敏度为92％，同样条件下，SnO2纳米粒子膜的灵 敏度仅为4％。说明PtO-Pt纳米粒子膜的催化作用能够显著提高TiO2和SnO2的膜氢 敏性能。另外，TiO2/PtO-Pt复合膜和SnO2/PtO-Pt复合膜均对空气中H2有很高的选 择性。     

糖葫芦状二氧化钛纳米线阵列的制备及其光催化性能

 采用溶胶-电泳技术,在多孔阳极氧化铝(PAA)模板的有序孔洞中制备了高度取向的糖葫芦状TiO2纳米线阵列光催化剂,通过扫描电镜(SEM)和X射线衍射对样品进行了表征. 结果表明, TiO2纳米线为锐钛矿晶型,纳米线直径与PAA模板的孔径一致,且分布均匀. 纳米线取向性极好,每根纳米线都具有周期性凹凸,形似糖葫芦,因此命名为糖葫芦状TiO2纳米线阵列. 以甲基橙的降解反应评价了光催化剂的活性,与相同条件下制备的TiO2/玻璃膜相比, TiO2纳米线阵列在光照1 h时对甲基橙的降解率达到93.6%, 比前者提高了40.2%, 具有很好的光催化活性.     

纳米晶粒TiO2多孔微球的合成与表征

 钛酸四丁酯经酸性水解得到TiO2溶胶，将溶胶与苯酚混合后加入到正庚烷分散介质中，再滴加甲醛水溶液，通过反相悬浮聚合和溶胶－凝胶过程制备了聚合物与TiO2的复合微球．对复合微球进行焙烧处理，使聚合物分解，从而得到由纳米TiO2晶粒组成的多孔微球．以示差扫描量热法、热重分析、X射线衍射、扫描电子显微镜和氮吸附等方法对TiO2多孔微球的物理性质进行了表征．结果表明，所得TiO2多孔微球主要由锐钛型TiO2纳米晶粒组成，晶粒尺寸为20～30nm；TiO2多孔微球的直径为200～500μm，比表面积为87．40m2／g，平均孔径为8．65nm，孔径的分布具有单分散特征．     

不同基材上TiO2膜的表征和光催化活性评价

 采用溶胶-凝胶法在平行条件下制备了负载于钛、铝、不锈钢和玻璃等不同基材上的TiO2浸渍提拉膜,利用原子力显微镜、俄歇电子能谱、X射线衍射、漫反射紫外-可见光谱和苯甲酰胺光催化降解等手段对TiO2膜进行了表征和催化活性评价. 实验结果表明,基材的种类对TiO2膜的性能有较大影响,各膜样品虽均为锐钛矿晶型,但表面形貌显著不同. TiO2/Ti, TiO2/steel, TiO2/Al和TiO2/glass上TiO2的平均粒径分别是152, 205, 241和477 nm,且前两者的粒径分布较为集中. TiO2/Ti和TiO2/Al样品表面仅有Ti和O元素存在,而TiO2/steel和TiO2/glass表面则分别检测到有Fe和Na,Ca及Si等基材元素渗出. 各膜样品对苯甲酰胺光催化降解的活性次序是:TiO2/Ti＞TiO2/Al＞TiO2/glass＞TiO2/steel. 根据实验结果可以推测,在焙烧阶段各基材上前驱体膜烧结行为的不同以及基材元素的渗出是造成不同基材上的TiO2膜在表面形貌、化学组成、光吸收性能以及光催化活性方面存在明显差异的主要原因.     

制备条件对PANI/PATP/Au和TiO_2-PANI/PATP/Au膜光电化学性能的影响

应用电化学方法在不同条件下制备聚苯胺 (PANI)膜和TiO2 -PANI复合膜 ,并对其光电化学性能进行研究 .实验表明 ,制备条件是影响膜光电化学性能的重要因素 .对氨基硫酚 (PATP)的组装有利于改善PANI膜的附着力 ;部分氧化态PANI膜的光电化学响应明显优于还原态和氧化态PANI膜的光电化学响应 ;部分氧化态PANI膜的厚度对其光电化学性能有一最佳值 ;热处理虽然有利于改善TiO2 的光电化学性能 ,但温度太高 ,将破坏PANI膜的表面结构 ,对于TiO2 -PANI复合膜有一最佳的热处理温度 .优化制备条件大可改善TiO2 -PANI复合膜和PANI膜的光电化学性能     

纳米TiO_2粒径、孔径对酸性紫43吸附动力学与热力学行为的影响

探究锐钛型纳米TiO2粒径(5-10、25、40、60、100nm)及孔径(96,120,134,143,52)对染料废水(酸性紫43)吸附动力学与热力学行为的影响。假二级方程和准一级方程分别能准确描述TiO2粒径≤100nm吸附动力学过程。经Weber-Morris和Dumwald-Wagner扩散模型分析,吸附速率由膜扩散和内扩散共同控制并受粒径影响。吸附热力学符合Langmuir等温吸附方程,最大吸附量(Qmax)与孔径正相关,与粒径无关,60nm TiO2孔径最大,吸附效果最好,Qm可达104.17mg/g;参数40kJ/mol△H0,吉布斯自由能△G0,受温度影响不大,说明吸附过程是自发的吸热反应,以物理吸附为主。     

掺杂TiO2光催化膜材料的制备及其灭菌机理

采用sol-gel技术制备了掺杂TiO2膜,考察了制备条件对溶胶稳定性的影响,并从TiO2光催化反应的角度分析了膜功能材料的灭菌机理.结果表明,溶胶化过程中温度对掺杂胶体形成速度及胶体粒径分布影响很大,40℃时制备周期短,胶体稳定.TiO2膜材料的灭菌本质在于其光照激活后产生的自由基OH·和O-2·直接攻击细菌的细胞,致使细菌蛋白质变异或脂类分解,从而杀灭细菌并使之分解.TiO2膜功能材料的灭菌效果与TiO2晶相组成直接相关,其灭菌率随膜层中锐钛矿含量的增加而提高.     

TiO_2/PVDF复合中空纤维膜的制备和表征

采用相转化法制备了二氧化钛 (TiO2 ) 聚偏氟乙烯 (PVDF)复合中空纤维膜 .应用牛血清白蛋白截留实验、扫描电子显微镜、热重分析、X射线衍射分别对复合膜的分离性能、微观结构、热稳定性和晶相组成进行了分析 .结果表明复合膜的性能与纯PVDF膜的相比有显著的改善 ,其中对牛血清白蛋白的截留率从 3 2 7%提高到 86 6 7% ,单根纤维的断裂应力从 3 35MPa提高到 4 70MPa ,提高了 4 0 3% .氮气吸附实验测定的孔径分布进一步表明复合膜的孔径分布变窄 ,孔径变小 .     

TiO2纳米管的模板法制备及表征

TiO2纳米材料在太阳能的储存与利用、光电转换、光致变色及光催化降解大气和水中的污染物等方面具有广阔的应用前景,成为重点研究的课题之一[1～5].目前,以TiO2纳米粉体和纳米膜的研究较为普遍,而TiO2纳米管的报道不多.由于纳米管比纳米膜具有更大的比表面积,因而具有较高的吸附能力,可望提高TiO2的光电转换效率.模板法(包括多孔阳极氧化铝膜(PAA)、光刻蚀制备的纳米模板、聚碳酸酯纳米滤膜等)在制备导电聚合物、金属、碳、无机半导体等纳米管或线型材料方面已得到广泛应用[6～9],在这些模板中,PAA膜具有均匀分布的垂直于表面的相互平行的密集纳米孔,且孔径、孔间距、膜厚可以通过电化学手段加以控制[10～13].     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.