Effect of sodium alginate modification of graphene (by ‘anion-π’ type of interaction) on the mechanical and thermal properties of polyvinyl alcohol (PVA) nanocomposites

Layered aligned dispersion of graphene in graphene/polyvinyl alcohol (PVA) nanocomposites is prepared in the form of films through simple solution processing route. The results indicate that there exist an interfacial interaction between PVA and graphene because of hydrogen bonding. This is responsible for the change in structure of PVA (such as decrease in the level of crystallization) and exhibiting ductile PVA nanocomposite film with improved tensile modulus, tensile strength, and thermal stability. Moreover, to improve the mechanical properties of PVA nanocomposites, graphene is successfully modified using a non-covalent modifier, sodium alginate (SA) and there exist an ‘anion-π’ type of interaction in between SA and graphene. The modification results in finer dispersion of the graphene in PVA/SA-m-graphene nanocomposites. In addition, there exist a hydrogen bonding in between PVA and SA. This has resulted in the remarkable improvement in mechanical properties of PVA/SA-m-graphene nanocomposites as compared to pure PVA and PVA/graphene nanocomposites. The increase in mechanical properties of PVA/SA-m-graphene nanocomposites is achieved through better load transfer from graphene to polymer matrix, despite decrease in crystallinity of PVA. Improvement in tensile modulus and tensile strength is highest at 0.5 wt.% of SA-modified graphene in PVA/SA-m-graphene nanocomposites because of finer dispersion of graphene and is 62 and 40% higher than that of pure PVA. Addition of SA-modified graphene also improves the thermal stability of PVA/SA-m-graphene nanocomposites remarkably as compared to unmodified graphene PVA nanocomposites.     

Flexible and transparent resistive switching devices using Au nanoparticles decorated reduced graphene oxide in polyvinyl alcohol matrix

We have investigated the resistive switching mechanism in solution processed Au-reduced graphene oxide-polyvinyl alcohol (PVA) nanocomposites on flexible substrates. Monodispersed gold nanoparticles (Au NPs) attached to reduced graphene oxide (RGO) in aqueous PVA solution have been synthesized using a novel one pot technique. The fabricated hybrid device showed high On/Off switching ratio more than 10³ with low operating voltages. The performance of hybrid device can be effectively enhanced over control RGO device. The switching mechanism occurs from the electrochemical reduction/oxidation process of partially reduced graphene oxide. The proposed devices reveal superior asymmetric bipolar resistive switching characteristics attractive for solution processable flexible and transparent non-volatile memory applications.     

A simple strategy to fabricate poly (acrylamide-co-alginate)/gold nanocomposites for inactivation of bacteria

A facile and efficient approach to prepare uniform gold nanoparticles (Au NPs) in hybrid hydrogel consisting of acrylamide (AM) and alginate (SA) for antibacterial applications is reported. In this study, reduction of gold ions by acrylamide and alginate (AM–SA) occurred before the polymerization and as-obtained gold colloids are stabilized by AM–SA immediately in the absence of commonly used reducing agents and protective reagents. Via transmittance electron microscopy results, we can conclude that the obtained gold nanoparticles in hydrogel are well dispersed. Furthermore, ultraviolet–visible absorption spectroscopy, Fourier transform infrared and thermogravimetric analysis were used to characterize the structure and composition of the synthetic nanocomposites. Our approach provides well-dispersed nanoparticles around 8 mm in size. It is important to underline that nanoparticle aggregation was not observed during and after gel formation. The prepared Au NPs exhibited remarkable stability in the presence of high pH s, and a range of salt concentrations. Importantly, the hydrogel/gold nanocomposites showed a non-compromised activity to inhibit the growth of a model bacterium, Escherichia coli. With their excellent mechanical behavior, as well as the remained antibacterial activity, the nanocomposites should get various potential applications in the fields of pharmaceutical science and tissue engineering.     

Synthesis and comparative study of optical and electrical properties of Au-doped carbon nanotubes prepared in different reaction media

We introduce the synthesis, characterization and physical properties of gold (Au) doped multiwalled carbon nanotubes (MWCNTs) in different reaction media. In order to dope MWCNTs with Au nanoparticles (NPs), first functionalized carbon nanotubes (f-MWCNTs) were prepared. The reduction of gold (III) chloride trihydrate for synthesizing Au NPs in the presence of f-MWCNTs was performed by using sodium citrate as a reducing agent. The produced nanocomposites were characterized using FTIR, XRD and TEM analyses to explore their chemical structures and morphologies. All of the samples have been characterized by TGA and resultantly, the composite made into ethylene glycol exhibited the most concentration of Au NPs into the composite network. This work probes the optical characteristics, such as UV–vis absorption, and optical band gap. Hall effect analyses declared some pleasing variations in electrical characteristics. Remarkably, the n-type doping of Au NPs in the p-type MWCNTs’ network led to a downshift of the Fermi level. This process increased the doped samples electrical conductivity. The results indicated that modification of MWCNTs with Au NPs has generally an important role in decreasing the band gap and increasing the electrical activity of MWCNTs. Our research outcomes provide a new vision into how different reaction media could affect the characteristics of MWCNT/Au nanocomposites. We discovered that ethylene glycol could be considered as a perfect reaction medium for preparation of high-quality doped CNTs with excellent physical properties. Our effort opens up the door to far more investigations on the role of the reaction medium in products’ characteristics.     

Effects of enhanced hydrogen bonding on the mechanical properties of poly (vinyl alcohol)/carbon nanotubes nanocomposites

In this study, poly (vinyl alcohol) (PVA) composites reinforced by multiwall carbon nanotubes (MWCNTs) functionalized with either phenolic hydroxyl groups (MWCNTs-f-OH) or PVP molecule (PVP@MWCNTs) were fabricated. The objective was to elucidate the effect of different MWCNTs surface functionalization on the mechanical properties of the nanocomposites. It was found that both of PVP@MWCNTs and MWCNTs-f-OH had a good dispersion in PVA matrix. However, the MWCNTs-f-OH had stronger effective interfacial interaction with PVA matrix than PVP@MWCNTs, owe to the formation of hydrogen bonds between MWCNTs-f-OH and PVA. The stress-strain measurements showed that the Young’s modulus and tensile strength of MWCNTs-f-OH/PVA with only 1.0 wt.% contents increased by 200 and 100% compare with that of PVA, respectively. The findings of this experimental study emphasized the critical role of MWCNTs surface morphology in determining the mechanical properties of nanocomposites, and shed new light on understanding and advancing the properties of carbon nanotube based composites.     

Theory of passive mode locking of solid-state lasers using metal nanocomposites as slow saturable absorbers

Mode locking of solid-state lasers using metal nanocomposites as slow saturable absorbers (SAs) is studied theoretically. The derived equation for the transient nonlinear response of metal nanocomposites is based on the semiclassical two-temperature model. The model is confirmed experimentally by pump-probe measurements on Au nanoparticles (NPs). The theory was applied to study passive mode locking of a solid-state laser containing Au NPs as SA in the green spectral range. Pulse durations as short as 100 fs are predicted, and design criteria of metal NP SAs are derived.     

Effect of gamma irradiation on the structural and optical properties of PVA/CdS nanocomposite films prepared by ex-situ technique

ABSTRACT

For a comprehensive understanding of the PVA/CdS nanocomposite properties, it is essential to select the suitable method for their preparation as well as elucidate the interfacial interactions, which still need support. CdS nanoparticles have been prepared by thermolysis method under the flow of nitrogen. Rietveld refinement of x-ray data shows that all the CdS samples have both cubic and hexagonal structures. Then PVA/CdS films were prepared by ex-situ technique. Samples from PVA/CdS nanocomposite have been irradiated with gamma doses in the range 10–120?kGy. The implanting of CdS NPs into PVA matrix was confirmed by XRD hand in hand with UV–vis and FTIR spectroscopic techniques. UV/VIS absorption spectra confirm the formation of hybridized film CdS/PVA nanocomposite with a refractive index in the range of 1.32–1.48 (at 500?nm). UV/VIS measurements were also used in calculating different optical parameters such as refractive index, extinction coefficient and optical band gap energy. Additionally, Tauc’s relation was used to determine the type of electronic transition. It is found that the gamma irradiation in the dose range 30-90?kGy led to a more compact structure of PVA/CdS nanocomposite and causes proper dispersion of CdS nanoparticles in the PVA matrix. This led to the formation of coordination reaction between OH of PVA and CdS nanoparticles, resulted in an increase in refractive index and the amorphous phase. Also, the gamma irradiation reduces the optical energy gap from 4.53 to 2.19?eV, and accompanied with an increase in the Urbach energy from 2.28 to 4.46?eV, at that dose range which could be attributed to the increase in structural disorder of the irradiated PVA/CdS nanocomposites due to crosslinking. Further, the color intensity ΔE, which is the color difference between the non-irradiated sample and the irradiated ones, was increased, from 0 to 10.8, with increasing the gamma dose, convoyed by an increase in the red and yellow color components.     

Stabilizer specific interaction of gold nanoparticles with a thermosensitive polymer hydrogel

We report the experimental results on temperature-dependent studies of interactions between a novel biocompatible thermosensitive polymer hydrogel and different stabilizing agent capped gold nanoparticles (Au NPs) with particle size ranging from 5 to 20 nm. Stabilizing agents such as thioglycolic acid, tryptophan, and phenylalanine have been used as capping agents for Au NPs. The poly-N-isopropyl acrylamide-co-acrylic acid (pNIPAm-AAc) with 3.0 ± 0.7 μm in size was synthesized by radical polymerization of a selected mixture of N-isopropyl acrylamide (NIPAm), methylene-bis-acrylamide and acrylic acid (AAc). The capped Au NPs were mixed with a solution of pNIPAm-AAc hydrogel. The temperature-dependent properties of the mixture were studied by UV–vis spectroscopy, dynamic light scattering based particle size analysis, and transmission electron microscopy (TEM). The observations indicated change in the lower critical solution temperature (LCST) depending on the nature of the stabilizer, with hydrophobic ones lowering the value while hydrophilic stabilizers increasing the same. Also, the optical absorption due to Au NPs, when stabilized with hydrophobic groups, reduced significantly at above LCST along with significant blue shift of wavelength maximum.     

Nanoindentation of gold nanoparticles functionalized with proteins

The hardness and Young's modulus of 10 and 20 nm gold nanoparticles (Au NPs) modified with bovine serum albumin and streptavidin were measured using a nanoindenter. The Au NPs were immobilized on a semiconductor surface through organic self-assembled monolayers. Changes in mechanical properties occurred when the Au NPs were immobilized on the surface. The hardness and Young's modulus were dependent on the size of the NPs, and the proteins on the particles showed highly plastic and elastic behavior compared to flat surfaces modified with self-assembled monolayers.     

不同形貌金纳米粒子的制备及其表面增强拉曼散射效应的研究

不同形状的金纳米粒子在表面增强拉曼散射(surface enhanced Raman scattering,SERS)中有不同的增强效果,多面体金纳米粒子具有多角结构,显示出比金纳米板更为明显的增强效果,近年来对其合成和性质的研究备受关注。该研究探究了十二面体,二十面体,三角板,球形四种形状的金纳米粒子在SERS中不同的增强效果。分别采用硼氢化钠还原法和以N,N-二甲基甲酰胺(DMF)为还原剂制备金三角纳米片和二十面体金纳米粒子,又以二十面体金纳米粒子为种子制备出十二面体金纳米粒子,并分别以以上三种不同形貌的金纳米粒子及球形金溶胶为基底,4-巯基吡啶,对巯基苯甲酸为探针分子检测了其在不同激发波长下的增强效果。透射电子显微镜结果表明金三角纳米板的平均边长为130nm,二十面体和十二面体金纳米粒子的粒径分别为100和120nm。三者的紫外可见吸收峰分别在589,598和544nm处。表面增强拉曼散射结果表明金多面体比金三角纳米板表现出更好的增强效果。     

金纳米粒子的制备及其表面增强拉曼散射效应的研究

采用多巴胺化学还原法制备了分散性良好的纳米金溶胶,并检测了其作为表面增强拉曼散射(Surface Enhanced Raman Scattering,SERS)基底的性质。粒度和透射电子显微镜测试结果表明金溶胶为平均粒径30nm左右的球形颗粒,并且紫外-可见特征吸收峰出现在520nm,为典型的金纳米颗粒特征吸收峰。以罗丹明6G(R6G)为探针分子证明了金溶胶良好的SERS增强效果,用金溶胶对除草剂敌草快(DQ)进行检测,最低检测限可达1×10-7 mol/L。结果表明所制备的金溶胶具有良好的表面增强拉曼散射活性。     

硒化镉发光量子点的制备及其在有机发光器件中的应用

硒化镉量子点具有随粒径尺寸改变,而产生发光波长调变的特性,目前已被广泛研究。本研究是由化学溶胶法合成不同粒径尺寸的核壳型CdSe／ZnS硒化镉量子点,其表面包覆十六烷基胺,避免分子团聚现象。在由硒化镉成核温度的控制,成功地制备一系列具有各种尺寸粒径的核壳型硒化镉量子点(2—6nm)。本研究也合成了含有纳米金粒子于核壳型硒化镉量子点,实验结果发现：硒化镉发光效率明显的提高。在有机发光器件的应用方面,将发光波长为505nm核壳型CdSe／ZnS量子点掺入溶有发光波长为570nm铱化合物的氯仿溶液时,其溶液的光致发光光谱表明,原量子点的发光特性消失,只有铱化合物的发光依然存在,且其发光强度呈现明显增强趋势,我们推测此现象源自于量子点到铱化合物能量转移的机制。我们也以含有核壳型硒化镉量子点的铱化合物与PVK混合材料为发光层,成功的制作发光二极管器件,器件的发光效率因核壳型硒化镉的掺杂,明显提高2倍多。     

Plasmonic enhancement of the vanadium dioxide phase transition induced by low-power laser irradiation

Nanocomposites consisting of gold nanoparticle (NP) arrays and vanadium dioxide (VO₂) thin films are noteworthy for the tunability of both their thermal and optical properties. The localized surface plasmon resonance (LSPR) of the Au can be tuned when its dielectric environment is modulated by the semiconducting-to-metal phase transition (SMT) of the VO₂; the LSPR itself can be altered by changing the shape of the NPs and the pitch of the NP array. In principle, then it should be possible to choose a combination of VO₂ film and Au LSPR properties that maximizes the overall optical response of the nanocomposite. To demonstrate this effect, transient transmission measurements were conducted on lithographically fabricated arrays of Au NPs of diameter 140?nm, array spacing 350 nm, and covered with a 60?nm thick films of VO₂ via pulsed laser deposition. Both Au::VO₂ nanocomposites and bare VO₂ film were irradiated with a shuttered 785?nm pump laser, and their optical response was probed at 1550?nm by a fixed-frequency diode laser. The Au::VO₂ nanocomposite exhibited an increased effective absorption coefficient 1.5 times that of the plain film and required 37?% less laser power to induce the SMT. The time-dependent temperature rise in the film as a function of laser intensity was calculated from these measurements and compared with both analytic and finite-element models. Our results suggest that Au::VO₂ nanocomposites may be useful in applications such as thermal-management coatings for energy efficient ??smart?? windows.     

Ultrasonic assisted functionalization of MWCNT and synergistic electrocatalytic effect of nano-hydroxyapatite incorporated MWCNT-chitosan scaffolds for sensing of nitrofurantoin

In the present work, we report the fabrication of stable composite of chitosan hydrogels (CHI) on multiwalled carbon nanotubes (MWCNT) using a simple ultrasonic-assisted method. Also, rod-like hydroxyapatite nanoparticles (HA NPs) were synthesised using a hydrothermal route and were incorporated into the highly conductive MWCNT-CHI scaffolds using an ultrasonication method. The functionalization of MWCNT and preparation of HA NPs on MWCNT-CHI nanocomposite were done using the sonication over the frequency of 37 kHz with the ultrasonic power capable of 150 W (Elmasonic Easy 60H bath sonicator). The resulting hybrid HA NPs/MWCNT-CHI nanocomposites have an excellent surface area and high surface to volume ratio, which leads to the sensitive detection of nitrofurantoin than pristine MWCNT and HA NPs. The complete elemental and morphological analyses of the HA NPs/MWCNT-CHI nanocomposites were characterised by XRD, FTIR, RAMAN, FESEM, TEM, EDX, and elemental mapping techniques. Electrochemical analysis of the HA NPs/MWCNT-CHI nanocomposites was carried out by cyclic voltammetry, electrochemical impedance spectroscopy and amperometry methods. The modified glassy carbon electrode (GCE) of HA NPs/MWCNT-CHI nanocomposites exhibit the nitrofurantoin detection activity at the linear range of 0.005–982.1 µM with the detection limit of 1.3 nM. The synergistic electrocatalytic activity of HA NPs/MWCNT-CHI nanocomposites modified GCE is correlated to the sensitivity of 0.16 µAµM⁻¹ cm⁻² with excellent precision and accuracy towards the sensing of nitrofurantoin.     

Synthesis of composite gold/tin-oxide nanoparticles by nano-soldering

Composite Au–SnO₂ nanoparticles (NPs) are synthesized by nano-soldering of pure Au and SnO₂ NPs. The multi-step process involves synthesis of pure Au and SnO₂ NPs separately by nanosecond pulse laser ablation of pure gold and pure tin targets in deionized water and post-ablation laser heating of mixed solution of Au colloidal and SnO₂ colloidal to form nanocomposite. Transmission Electron Microscopy (TEM) and High-Resolution Transmission Electron Microscopy (HRTEM) were used to study the effect of laser irradiation time on morphology of the composite Au–SnO₂ NPs. The spherical particles of 4 nm mean size were obtained for 5 min of post-laser heating. Increased mean size and elongated particles were observed on further laser heating. UV–vis spectra of Au–SnO₂ nanocomposites show red shift in the plasmon resonance absorption peak and line shape broadening with respect to pure Au NPs. The negative binding energy shift of Au 4f_7/2 peak observed in X-ray Photoelectron Spectra (XPS) indicates charge transfer in the nano-soldered Au–SnO₂ between gold and tin oxide and formation of soldered nanocomposite.     

Styrene butadiene rubber-clay nanocomposites using a latex method: morphology and mechanical properties

In this study, octadecylamine modified MMT (C18-MMT) filled SBR nanocomposites were manufactured using a latex method and a compounding method. Cure characteristics and mechanical properties of SBR compounds filled with C18-MMT, Cloisite 15A, carbon black and Na-MMT were also evaluated. By using the latex method, the number of layers of the silicates in the SBR matrix reduced from the original 14–15 layers to 1–4 layers. This was due to the presence of octadecyl ammonium ions which reduced the number of layers of the re-aggregated silicates during the process of co-coagulation. The SBR/C18-MMT nanocomposites using the latex method showed the highest oscillating disc rheometer (ODR) torques, tensile strength, modulus and tear energy. These increased mechanical properties can be attributed to the excellent reinforcing effect of the silicates well dispersed in the rubber matrix rather than the effect of the increase in the degree of crosslinking. Without alkyl ammonium ions in the latex method, the level of dispersion of silicates in the SBR matrix was very poor. The SBR/C18-MMT nanocomposites using the compounding method were found to have a lower degree of modulus, tensile strength and tear energy due to the low level of the dispersion of silicates than the SBR/C18-MMT nanocomposites using the latex method.     

Preparation and Characterization of Chemically Crosslinked Polyvinyl Alcohol/Carboxylated Nanocrystalline Cellulose Nanocomposite Hydrogel Films with High Mechanical Strength

Chemically crosslinked polyvinyl alcohol (PVA)/carboxylated nanocry-stalline cellulose (PVA/CNCC) nanocomposite hydrogel films were fabricated by film-casting of PVA/CNCC mixture solutions and subsequent thermal-curing of the PVA with the CNCC. Gel fractions of the hydrogel films were measured to confirm the occurrence of crosslinking. Morphologies of the hydrogel films were characterized by polarized light microscopy and scanning electron microscopy (SEM). Thermal properties, swelling behavior and mechanical properties of the hydrogel films were investigated to evaluate the influence of CNCC content (10～30% of PVA mass). Equilibrium water content of the hydrogel films was in the range of 40～49%. At swelling equilibrium, the hydrogel films could be stretched to 3～3.4 times their original length, and their tensile strength was in the range of 7.9～11.6 MPa. The results show that the PVA/CNCC nanocomposite hydrogel films were both extensible and highly tough.     

Simple method to prepare size‐controllable gold nanoparticles in solutions and their applications on surface‐enhanced Raman scattering

We report here, for the first time, a simple method to prepare size‐controllable Au nanoparticles (NPs) in aqueous solutions from bulk Au substrates. First, chitosan (Ch)‐capped Au‐containing complexes were prepared by electrochemical oxidation–reduction cycles in 0.1 N NaCl and 1 g/l Ch solutions. Then the solutions were heated from room temperature to boiling at different heating rates to synthesize size‐controllable Au NPs. The particle sizes of the prepared Au(111) NPs could be controlled from 5 to 30 nm with an increase of the heating rate during preparation. Experimental results indicate that the prepared Au(111) NPs with diameters ranging from 10 to 30 nm can serve as surface‐enhanced Raman scattering active probes for molecules of rhodamine 6G. Copyright © 2010 John Wiley & Sons, Ltd.     

In Vitro Assessment of Poly (Vinyl Alcohol) Film Incorporating Aloe Vera for Potential Application as a Wound Dressing

Since skin tissue acts as a vital protective barrier between the body and the external atmosphere, the repair or regeneration of skin injuries serves as a great challenge in regenerative medicine. Herein, hydrogel films composed of poly vinyl alcohol (PVA) and aloe vera (AV) extracted gel were prepared and characterized for wound dressing application. The physical and morphological properties, water absorption capacity, biodegradation behavior, and water transmission rate were characterized for several variations in the AV content (0–50%). The cytocompatibility of the films, as well as cell morphology in response to different films, was assessed using MTT assay and SEM, respectively. According to the results, AV incorporation improved the surface morphology, water absorption capacity, in vitro degradation rate, and water vapor permeability of the PVA films. However, these properties were affected by the AV content. The mechanical properties of the films were enhanced by introducing AV up to 30%, and then decreased significantly with further AV increase. Evaluation of fibroblast proliferation showed that AV can positively improve the bioactivity of the films without any cytotoxicity. In conclusion, the results demonstrated that PVA/AV optimized hydrogel film can be suggested as promising wound dressings for improving wound treatment.     

Molecular crystallization of rubrene thin films assisted by gold nanoparticles

We demonstrate that crystalline organic rubrene thin films can be obtained by a facile spin-coating method using gold (Au) nanoparticles (NPs). Dodecanethiol-functionalized Au NPs were dissolved with rubrene molecules in solvent and a thin film of Au/rubrene was prepared by a simple spin coating process. The results of confocal photoluminescence (PL) and absorption spectral mapping confirmed the local formation of orthorhombic crystalline structures of the Au/rubrene hybrid film, in contrast to the monoclinic structure of plain rubrene films. Further, the results of transmission electron microscopy (TEM) and X-ray diffraction analysis, as well as Raman spectroscopy measurements of the rubrene and Au/rubrene films suggested the formation of high crystalline Au/rubrene film. The molecular crystallization of the Au/rubrene hybrid film is attributed to the nucleation effect of the Au NPs.