磁性纳米复合物的制备及对铜离子(Ⅱ)的传感检测

采用化学共沉淀法合成硅包覆的磁性纳米粒子Fe_3O_4@SiO_2,进一步通过六亚甲基二异氰酸酯将吡哆酰肼分子(Pyh)接枝到Fe_3O_4@SiO_2表面,制得功能化的磁性纳米复合物(Fe_3O_4@SiO_2-Pyh)。通过傅里叶变换红外光谱、透射电子显微镜、X射线衍射等技术手段对其结构、形貌和磁性能进行了表征。Fe_3O_4@SiO_2-Pyh粒子具有规则的核壳结构,粒径分布在50~55 nm,壳层厚度约为15 nm。Fe_3O_4@SiO_2-Pyh结构中含有酰腙类活性基团—CO—NH—N=CH—,能与Cu~(2+)形成稳定的配合物,在此基础上采用紫外可见吸收光谱特性建立了测定Cu~(2+)的分析方法,线性范围为3.4×10~(-7)~4.5×10~(-6)mol/L,检出限为1.03×10~(-7)mol/L。此外,利用Fe_3O_4@SiO_2-Pyh良好的磁响应,通过外部磁场能够有效地除去水中过量的铜离子,在环境领域具有潜在的应用价值。     

具有光催化与光芬顿反应协同作用的2D/2D α-Fe2O3/g-C3N4 S型异质结用于高效降解四环素

构建具有高效电荷迁移效率和丰富活性位点的异质结光催化体系是提升光芬顿反应速率的有效途径。本研究通过简单的水热法合成了2D/2D结构的α-Fe₂O₃/g-C₃N₄ S型异质结光芬顿催化剂,并使用X射线衍射仪技术(XRD)、透射电子显微镜(TEM)、傅立叶变换红外吸收光谱(FTIR)和紫外-可见吸收光谱(UV-Vis)等分析手段对α-Fe₂O₃/g-C₃N₄的晶体结构、微观结构、化学组分和光学性质进行了详细的表征。通过在可见光照射下降解四环素,评测了α-Fe₂O₃/g-C₃N₄的催化活性。结果表明,光催化反应与芬顿反应的协同作用使α-Fe₂O₃/g-C₃N₄ (1 : 1)展现出了优异的光芬顿催化活性：在可见光照射下,仅加入微量的双氧水便可辅助催化剂在20 min内对四环素的降解率达到78%,其降解速率分别是单一的α-Fe₂O₃和g-C₃N₄的3.5倍和5.8倍。α-Fe₂O₃/g-C₃N₄复合材料优异的催化活性得益于在2D/2D S型电荷迁移机制上构建的光芬顿催化体系。2D/2D S型异质结能够显著促进电子和空穴的传输与分离,并为催化剂提供较大的比表面积和丰富的活性位点,同时还能保持复合材料最佳的氧化还原能力。此外,光催化反应促进了Fe³⁺的还原,从而加速了芬顿反应中羟基自由基的产生。总之,本研究为构建高效、稳定的光芬顿催化体系提供了一条简单有效的途径。     

WO3的引入对MnOx-Fe2O3催化剂上NH3-SCR反应中N2选择性的促进作用

采用溶胶-凝胶法制备了不同含量钨修饰的MnO_x-Fe₂O₃催化剂,重点考察WO₃的引入对NH₃-SCR反应中N₂选择性的影响,通过XRD、BET、XPS、H₂-TPR、Raman和In situ DRIFTS等手段对催化剂的物理化学性质进行表征。结果表明,钨的引入显著提高NH₃-SCR的N₂选择性,当WO₃质量分数为15%时,具有最佳的NH₃-SCR催化性能,且在50-250℃条件下N₂O浓度始终低于0.003%。这主要是由于适量WO₃的引入,导致催化剂物相由α-Fe₂O₃向γ-Fe₂O₃转变,并与锰相互作用形成新的无定型MnWO₄,获得较大的比表面积;使得Mn⁴⁺/（Mn³⁺+Mn⁴⁺）比例减少但Fe²⁺及表面化学吸附氧（O_α）含量增加,从而降低催化剂氧化性;增强催化剂表面的Lewis酸性位点的含量及强度,增强NH₃的吸附,促进了SCR反应,同时抑制了NO₂深度氧化形成硝酸盐物种,降低硝酸盐物种还原产生的副产物N₂O含量,从而显著提高WO₃-MnO_x-Fe₂O₃催化剂在NH₃-SCR中的N₂选择性。     

Ga_2O_3改性Cu/SiO_2催化剂降低水蒸气催化重整产物中CO选择性

采用蒸氨法制备的xGa-Cu/SiO_2催化剂可以同时产生Cu~0和Cu~+物种,加入Ga后催化剂的二甲醚水蒸气重整反应活性和选择性都有很大程度的提高,其中5Ga-Cu/SiO_2催化剂在380°C时的二甲醚转化率为99.8%,CO选择性为4.8%。通过透射电子显微镜(TEM),氢气-程序升温还原(H_2-TPR),N_2O滴定和X射线光电子能谱(XPS)结果发现,Ga与Cu物种之间的相互作用,一方面可以提高Cu物种的分散度,另一方面可以促进Cu~+的形成。通过改变Ga负载量可以调变Cu~+/(Cu~0+Cu~+)的比例,氢气的时空收率结果表明,Ga通过调变Cu~+/(Cu~0+Cu~+)影响催化活性,并且当Cu~+/(Cu~0+Cu~+)=0.5时,氢气时空收率达到最大值为5.02mol·g~(-1)·h~(-1)。程序升温表面反应(TPSR)结果表明,Ga通过促进水气变换反应提高反应产物CO_2选择性。     

丁二酸酐接枝纤维素纳米纤维膜及其重金属离子吸附

采用热致相分离(TIPS)法以三醋酸纤维素(TCA)为原料成功制备直径为(110±28)nm TCA多孔纳米纤维膜。将TCA纤维膜通过水解转化为纤维素(Cell)、接枝制备丁二酸酐接枝改性纤维素(Cell-g-SAA)膜。将Cell膜和Cell-g-SAA膜用于吸附水中Cu~(2+)、Pb~(2+),并对膜样品的吸附动力学、等温吸附和吸附热力学进行了研究。结果表明,二级动力学拟合和Langmuir模型更适合于该体系。与Cell膜相比,改性后Cell-g-SAA膜对Cu~(2+)和Pb~(2+)的最大吸附容量分别从51.73和34.29 mg/g增加到116.41和51.73 mg/g。纤维膜对Cu~(2+)、Pb~(2+)的吸附更趋近于单层吸附且化学吸附占主导地位。     

Fe3O4/HA复合吸附剂对Ni(Ⅱ)的吸附性能研究

采用碱溶酸析法提取腐植酸(HA),通过CaCl₂对其改性后与Fe₃O₄进行复合,制备出不同配比的Fe₃O₄/HA复合吸附剂。利用SEM、BET、FT-IR、XRD分析方法对HA、钙改性HA、Fe₃O₄/HA复合吸附剂进行了表征,考察了物料配比及吸附时间、pH值、温度、投加量和初始浓度对Ni(Ⅱ)吸附率的影响。结果表明:质量复合比mHA:mFe₃O₄:mCaCl₂为3∶2∶2的Fe₃O₄/HA复合吸附剂(HA2)对Ni(Ⅱ)吸附效果最佳。当加入0.8 g吸附剂,Ni(Ⅱ)初始浓度为0.1 g·L^-1,吸附5 h,pH=5,温度40℃,吸附剂对Ni(Ⅱ)的吸附率为92.57%。复合吸附剂在4次吸附脱附后,对Ni(Ⅱ)的吸附率仍达到52%。吸附过程符合准二级动力学方程和Freundlich吸附等温式。在20℃~40℃条件下,热力学参数ΔG<0、ΔS=37.57 J/(mol·K)、ΔH=11.07 kJ·mol^-1,表明该吸附是自发、熵增、吸热的过程。     

原位光沉积制备Z型α-Fe2O3/g-C3N4异质结及其可见光驱动光解水产氢性能

采用原位光沉积-煅烧法制得了Z型α-Fe₂O₃/g-C₃N₄异质结复合光催化剂。分别采用透射电子显微镜、X射线衍射、X射线光电子能谱、紫外可见漫反射光谱、荧光光谱以及电化学测试对样品进行了表征,并考察了可见光下光解水产氢活性。结果表明:当α-Fe₂O₃的负载量为2.9%时,α-Fe₂O₃/g-C₃N₄复合光催化剂具有最优的产氢催化活性,产氢速率高达1841.9μmol·g^-1·h^-1,约为g-C₃N₄的3.3倍。光催化性能的提高主要归因于3方面:(1)高温煅烧过程中α-Fe₂O₃的形成,有效促进了氮化碳片层的热剥离,增大了比表面积,从而为光催化反应提供了更多反应活性位;(2)超细α-Fe₂O₃颗粒(5~8 nm)高度均匀地分散在g-C₃N₄表面,并且与其紧密结合,形成了高质量的Z型异质结;(3)Z型异质结不仅有效抑制地了光生载流子的复合,同时极大地保留了g-C₃N₄导带电子的强还原性和α-Fe₂O₃价带空穴的强氧化性。     

新型Brnsted-Lewis酸性催化剂LaPW_(12)O_(40)/SiO_2制备及其在催化酯化反应合成生物柴油中的应用

以十二磷钨杂多酸(Tungstophosphoric acid,H_3PW_(12)O_(40))为基体,分别通过普通浸渍法、溶胶凝胶法和超声浸渍法进行了La3+改性作用,合成了三种固体酸催化剂A-LaPW_(12)O_(40)、B-LaPW_(12)O_(40)/Si O2和C-LaPW_(12)O_(40)。采用X射线荧光光谱(XRF)、孔径比表面积测定、X射线粉末衍射(XRD)、透射电镜(TEM)、红外光谱(FT-IR)、热重(TG)、N2吸附-脱附、NH3程序升温脱附(NH3-TPD)、吡啶吸附红外光谱(Py-FTIR)、X射线光电子能谱(XPS)等方法对合成的催化剂进行了表征,并比较了以上催化剂在用于催化以油酸和甲醇为反应物经酯化反应合成生物柴油时的活性和稳定性。结果表明,B-LaPW_(12)O_(40)/Si O2具有最高催化活性,当甲醇与油酸的物质的量比为8∶1,催化剂用量为反应物总质量的2%,反应温度为65℃,反应1 h后,油酸的转化率即高达93%。循环使用B-LaPW_(12)O_(40)/Si O2催化剂六次后,油酸的转化率仍高达86.4%。B-LaPW_(12)O_(40)/Si O2的高催化活性和稳定性可归因于在溶胶凝胶的转化过程中,作为硅源材料的四乙氧基硅(TEOS)易在酸性条件下发生水解反应形成Si O2网络,进而Si O2网络中的硅醇键与H_3PW_(12)O_(40)中的H+发生配位作用,生成具有强静电吸附力的(≡Si-OH2+)(H2PW12O-40)络合物。随着该络合物的形成,促进了La3+在Si O2表面的吸附而堵塞了H_3PW_(12)O_(40)的孔道结构,抑制了H_3PW_(12)O_(40)颗粒在焙烧过程中进一步聚集长大。Si O2将作为载体并以干凝胶状态存在于B-LaPW_(12)O_(40)/Si O2催化剂中,由于Si O2凝胶的高比表面积而使B-LaPW_(12)O_(40)/Si O2具有了较大的比表面积,从H_3PW_(12)O_(40)的1.4 m2/g增加至31.3 m2/g。并且,通过吡啶吸附红外光谱确定B-LaPW_(12)O_(40)/Si O2为Br9nsted-Lewis酸型固体酸,由于Br9nsted酸位易与酯化反应过程中生成的水发生水合反应而失活,因而Lewis酸位的形成有助于减少催化剂的失活现象发生。Lewis酸位的出现可归因于(≡Si-OH2+)(H2PW12O-40)与吸附在其表面的具有强吸电子作用的La3+发生键合作用后生成了LaPW_(12)O_(40)/Si O2。     

CuAl2O4尖晶石结构对浆态床一氧化碳加氢性能的影响

采用固相法、 共沉淀法、 柠檬酸法和溶胶-凝胶法制备了CuAl₂O₄尖晶石, 在浆态床反应器上对其进行一氧化碳加氢反应活性评价, 并对CuAl₂O₄尖晶石的结构进行了表征. 研究发现, 不同方法制备的CuAl₂O₄尖晶石在织构参数、 表面富集程度和分解还原性能上存在明显差异, 进而影响其催化性能. 固相法所制尖晶石的孔径和孔容大, CuAl₂O₄表面富集程度最高, 致使尖晶石分解不完全, 但是其分解释放的CuO全部被还原, 且Cu⁺/Cu⁰占比相当高, 有利于提高产物中C₂₊OH选择性(达到31.1%). 而表面富集程度相对低的其它3种尖晶石分解完全, 但部分CuO未被还原, 且还原产物中Cu⁰占比提高, Cu⁰和γ-Al₂O₃发生协同作用促进二甲醚的生成, 其选择性最高可达72.9%.     

Preparation and application of a novel magnetic anion exchange resin for selective nitrate removal

正A novel magnetic anion exchange resin NDM-1 was prepared through suspension polymerization and then functionalized with ammonolysis and alkylating agents.Its application for selective removal of nitrate was performed in comparison with MIEX~.The results demonstrated that NDM-1 achieved higher efficiency in nitrate removal than MIEX~ did,with or without the existence of competing anion SO_4~(2-) ascribed to its longer alkyl chains on exchange sites.Combined with the advantage of easy separation due toγ-Fe_2O_3 implanted,the magnetic anion exchange resin NDM-1 was considered to be superior to MIEX~ for nitrate removal in practical application.     

钛改性对γ-Fe2O3选择催化还原脱硝性能强化机制的分子模拟研究

采用密度泛函理论（DFT）研究了典型过渡金属Ti掺杂改性对γ-Fe₂O₃选择催化还原（NH₃-SCR）脱硝性能强化影响的作用机制。构建了单Ti和双Ti在γ-Fe₂O₃（001）表面的不同Fe位置的掺杂模型，计算了表面掺杂形成能，探讨了O₂、NO和NH₃分子在Ti掺杂前后的γ-Fe₂O₃（001）表面的吸附特性，并进行了反应机理分析。结果表明，单Ti倾向于掺杂在八面体Fe_oct位，双Ti倾向于两个Fe_oct位。Ti的掺杂增强了催化剂表面对O₂的吸附能力，吸附性能随Ti掺杂量增加而增强。单Ti和双Ti的掺杂都抑制了NO以N端在催化剂表面的吸附。Ti能够强化NH₃的吸附，增强了Lewis酸位，有利于SCR反应。Ti的掺杂增大了NO₂生成的反应能垒，降低了γ-Fe₂O₃低温区的SCR反应。Ti的掺杂抑制了NH和N的形成，避免了NH₃的过度氧化，提高NH₃的利用率，有利于SCR反应，并且抑制了通过E-R机理产生的N₂O，具有良好的N₂选择性。Ti的掺杂能够改善γ-Fe₂O₃在NH₃-SCR中还原NO的性能。     

Synthesis and Characterization of Manganese-copper Spinel Ferrite Powders

Magnetic Mn_1-xCu_xFe₂O₄(x=0.2, 0.5, 0.8 and 1.0) nanoparticles were synthesized by single citrate precursor method. The samples were characterized by powder X-ray diffraction, vibrating sample magnetometry and electron paramagnetic resonance(EPR). For samples with a low copper content(x<0.5), the copper ions have a tendency to occupy and substitute the Fe³⁺ at the tetrahedral(A) sites. For samples with a high copper content(x>0.5), most Cu²⁺ enter into the octahedral(B) sites. Transfer of Fe³⁺ from octahedral sites to tetrahedral sites leads to the decrease of the saturation magnetization. Maximum coercivity is observed for CuFe₂O₄ nanoparticles due to the strengthened magnetic anisotropy arisen from the Jahn-Teller effect of the octahedral copper ions. The dependence of magnetic properties of Mn_0.8Cu_0.2Fe₂O₄ nanoparticles on calcination temperature was investigated. The cation distribution in Mn_0.8Cu_0.2Fe₂O₄ is sensitive to the calcination temperature.     

Metal-organic framework derived magnetic nanoporous carbon as an adsorbent for the magnetic solid-phase extraction of chlorophenols from mushroom sample

In this work, a metal-organic framework derived nanoporous carbon(MOF-5-C) was fabricated and modified with Fe_3O_4 magnetic nanoparticles. The resulting magnetic MOF-5-derived porous carbon(Fe_3O_4@MOF-5-C) was then used for the magnetic solid-phase extraction of chlorophenols(CPs) from mushroom samples prior to high performance liquid chromatography–ultraviolet detection. Scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and N_2 adsorption were used to characterize the adsorbent. After experimental optimization, the amount of the adsorbent was chosen as 8.0 mg, extraction time as 10 min, sample volume as 50 m L, desorption solvent as 0.4 m L(0.2 mL×2)of alkaline methanol, and sample p H as 6. Under the above optimized conditions, good linearity for the analytes was obtained in the range of 0.8–100.0 ng g~(-1)with the correlation coefficients between0.9923 and 0.9963. The limits of detection(S/N = 3) were in the range of 0.25–0.30 ng g~(-1), and the relative standard deviations were below 6.8%. The result showed that the Fe3O4@MOF-5-C has an excellent adsorption capacity for the analytes.     

Particle size effects on the thermal behaviour of maghemite synthesised by flame pyrolysis

Thermal treatment of pure nanoscale maghemite (γ-Fe₂O₃) powders under argon yields different products depending on particle size. Particles with a mean diameter above 15 nm transform to hematite (-Fe₂O₃). Smaller particles, which were synthesised under identical conditions but from solutions with lower Fe³⁺ concentrations, transform into magnetite (Fe₃O₄) during thermal treatment. This phenomenon can be explained by adsorbed or incorporated reducing carboxylate groups. The origin of the reducing species and possible reaction mechanisms with the maghemite particles are discussed.     

Preparation of mesoporous hematite particles by a forced hydrolysis reaction accompanying a peptide production reaction

The influence of carbodimide (CI), well known as a condensing agent for producing peptides from l-phenylalanine (l-Phe), on the formation of hematite (-Fe₂O₃) particles through a forced hydrolysis reaction of acidic FeCl₃ solution was examined. The large ellipsoidal particles were produced together with needle-like -FeOOH and fine Fe₃O₄ ones in the systems both with l-Phe and CI, though the system only with CI was not essentially changed the particle shape. CI produced the characteristic large ellipsoidal particle accompanying the production of peptides by condensing l-Phe. This behavior was explained by the adsorption of peptides on β-FeOOH and polynuclear (PN) particles; the adsorption of peptides retarded the phase transformation from β-FeOOH to hematite along with the heterogeneous aggregation of PNs, resulting the large ellipsoidal hematite particles. CI reduced Fe³⁺ to Fe²⁺ ions during aging the solution. The decomposition of urea, by-products of peptide formation, produced two kinds of amines to raise the solution pH and provided -FeOOH and Fe₃O₄ particles. The large ellipsoidal hematite particles exhibited large specific surface area and high mesoporosity by adsorption of peptides onto PN particles within the hematite particles. The morphology and inner structure of hematite particles were exceedingly altered by using a reaction of peptide production and this procedure is expected for a new developing method of high-quality porous materials.     

Adsorption and desorption of lysozyme on nano-sized magnetic particles and its conformational changes

Adsorption and desorption of lysozyme on nano-sized magnetic particles and its conformational change were studied in this work. Adsorption of lysozyme on nano-sized magnetic particles (Fe₃O₄) was carried out at different pH. Maximum adsorption of lysozyme (4.65 mg/m²) occurred at its isoelectric point (pI=11.1). Differential scanning calorimetry (DSC) results show that the lysozyme adsorbed on magnetic particles did not show any thermal transition over the range 20–100 °C. High desorption of lysozyme from magnetic particles was achieved using NaH₂PO₄ (pH 4.0) (90%) and NaSCN (pH 6.0) (97%) as desorbents. The conformational change of the lysozyme desorbed by NaH₂PO₄ was small, while the lysozyme desorbed by NaSCN underwent a significant conformational change as measured by the intrinsic fluorescence. Eighty-eight and 82% activity was retained in the desorbed enzyme for desorption by NaH₂PO₄ and NaSCN, respectively.     

12-钨磷酸及其盐的酸性与催化性能的研究

红外法研究结果表明12-钨磷酸Fe³⁺、Mg²⁺和Na⁺盐都具有L酸点和B酸点。用Benesi法测得10种12-钨磷酸盐的酸强度顺序为(Al³⁺、Fe³⁺、La³⁺、Cu²⁺、Cd²⁺>Zn²⁺>(Ca²⁺、Mg²⁺>(Na⁺、Li⁺,其酸量与抗衡阳离子的离子势和电负性大体成线性关系。还看出酸量与所含结晶水量有关。催化剂的酸量与其对异丙醇脱水反应和丁烯-1异构化反应的催化活性的关系表现出不同的特征,这可用“体相型”和“表面型”催化作用的不同特点来解释。     

Recycle Adsorption of Cu2+ on Amine-functionalized Mesoporous Silica Monolithic

3-Aminopropyltriethoxysilane functionalized worm-like mesoporous silica monolithic(WMSM-NH₂) was prepared and used as a new regenerable adsorbent for the removal of Cu²⁺ ions. The analysis results show that the WMSM-NH₂ monolithic had a high efficiency value of 99.3% for Cu²⁺ remediation when the Cu²⁺ solution was at an initial concentration of 10.32 mg/L. The regeneration study of the WMSM-NH₂ monolithic presented that the adsorption efficiency of 89.0% was remained and a mass of 92.0% was left after seven adsorption-desorption cycles were executed. The monolithic material with high resistance to the acid and good mechanical stability can facilitate the operations of adsorption and regeneration of the adsorbent.     

Coordination properties of 1-allyl-2-methylimidazole relative to some metal ions in the solid state and aqueous solution

Cobalt(II) and copper(II) complexes with 1-allyl-2-methylimidazole (L), of general formula [ML₂(NO₃)₂], have been prepared in the solid state. The compounds were characterised by structural, spectroscopic and magnetic measurements. The metal ions in both six coordinate complexes are surrounded by two nitrogen atoms of the imidazole rings and four oxygen atoms of the chelating nitrato group (the CoN₂O₄ and CuN₂O₄ chromophores). The structure of both chromophores is described by a very distorted tetragonal bipyramid. The formation of successive complexes of the azole with Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺ and Cd²⁺ in aqueous solution was followed potentiometrically. An irregularity in the K_n constants of successive Co²⁺ and Zn²⁺ complexes suggests a change in the coordination sphere of the central ions from octahedral to tetrahedral. With the Co²⁺–1-allyl-2-methylimidazole system, the change has been proven by inspection of the visible absorption spectra.     

介孔Fe/SBA-15非均相芬顿氧化水中难降解染料罗丹明B

以介孔二氧化硅SBA-15 为载体, 采用等体积浸渍法制备了Fe/SBA-15. 通过X射线衍射(XRD)、N₂吸附-脱附、扫描电镜(SEM)、透射电镜(TEM)和X射线光电子能谱(XPS)等技术对其进行了表征, 并用于对水溶液中罗丹明B (RhB)的芬顿氧化. 表征结果表明了Fe/SBA-15维持了长程有序的介孔结构, 孔径和比表面积都有所下降, 并呈现棒状体的聚集态, 平均直径为0.6 μm. Fe 以α-Fe₂O₃的形态同时存在于介孔孔道内外. 在Fe/SBA-15 和H₂O₂同时存在条件下RhB的去除是吸附和催化氧化降解的协同作用所致, 并且与Fe/SBA-15 投加量密切相关, 但与初始溶液pH 几乎无关. 当Fe/SBA-15 投加量为0.15 g·L^-1, RhB 初始浓度为10.0 mg·L^-1,H₂O₂/Fe³⁺摩尔比为2000:1,初始溶液pH为5.4和反应温度为21 ℃时, RhB去除率达到了93%. Fe/SBA-15的Langmiur 单分子层饱和吸附量为99.11 mg·g^-1. 此外, 采用H₂O₂浸泡方式对使用过的Fe/SBA-15可进行再生,连续6 次循环使用后仍可维持80%的RhB去除率, 且每次使用后Fe浸出浓度都在0.1 mg·L^-1 (或者0.6% (质量分数))以下. 基于淬灭实验、UV-Vis 光谱和气相色谱-质谱(GC-MS)联用仪分析的结果, 提出了RhB的去除机理. 非均相芬顿催化剂Fe/SBA-15可用于去除像RhB这样的生物难降解有机物.