Determination of rutin using a CeO2 nanoparticle-modified electrode

CeO₂ nanoparticles approximately 12 nm in size were synthesized and subsequently characterized by XRD, TEM and UV-vis spectroscopy. Then, a gold electrode modified with CeO₂ nanoparticles was constructed and characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The modified electrode demonstrated strong catalytic effects with high stability towards electrochemical oxidation of rutin. The anodic peak currents (measured by differential pulse voltammetry) increased linearly with the concentration of rutin in the range of 5.0 × 10⁻⁷–5.0 × 10⁻⁴ mol · L⁻¹. The detection limit (S/N = 3) was 2.0 × 10⁻⁷ mol · L⁻¹. The relative standard deviation (RSD) of 8 successive scans was 3.7% for 5.0 × 10⁻⁶ mol · L⁻¹ rutin. The method showed excellent sensitivity and stability, and the determination of rutin in tablets was satisfactory.     

Trace determination of clenbuterol with an MWCNT-Nafion nanocomposite modified electrode

A method for the determination of trace clenbuterol is described. Multi-walled carbon nanotubes (MWCNTs)-Nafion composite was used to modify the glassy carbon electrode (GCE). The modified electrode showed high sensitivity and good selectivity for clenbuterol detection. It offered a linear range of 1.0 × 10⁻⁹–1.0 × 10⁻⁶ mol · L⁻¹ with a detection limit of 5.0 × 10⁻¹⁰ mol · L⁻¹ in pH = 1.2 solution. The oxidation mechanism of clenbuterol on the electrode was also investigated. Correspondence: Xiao-Ya Hu, Department of Chemistry, Yang Zhou University, Yang Zhou, Jiang Su, P.R. China     

Adsorptive anodic stripping voltammetry of zirconium(IV)-alizarin red S complex at a carbon paste electrode

A sensitive adsorptive anodic stripping procedure for the determination of trace zirconium at a carbon paste electrode (CPE) has been developed. The method is based on adsorptive accumulation of the Zr(IV)-alizarin red S(ARS) complex onto the surface of the CPE, followed by oxidation of adsorbed species. The optimal experimental conditions include the use of 0.10 mol · L⁻¹ ammonium acetate buffer (pH 4.3), ARS, an accumulation potential of 0.20 V (versus SCE), an accumulation time of 2 min, a scan rate of 200 mV · s⁻¹ and a second-order derivative linear scan mode. The oxidation peak for the complex appears at 0.69 V. The peak current is proportional to the concentration of Zr(IV) over the range of 1.0 × 10⁻⁹–2.0 × 10⁻⁷ mol · L⁻¹, and the detection limit is 3 × 10⁻¹⁰ mol · L⁻¹ for a 2 min adsorption time. The relative standard deviations (n = 8) for 5.0 × 10⁻⁸ and 5.0 × 10⁻⁹ mol · L⁻¹ Zr(IV) are 3.3 and 4.8%, respectively. The proposed method was applied to the determination of zirconium in ore samples with satisfactory results.     

Voltammetric study of the interaction of the ofloxacin–copper complex with DNA, and its analytical application

The electrochemical behavior of the ofloxacin–copper complex, Cu(II)L₂, at a mercury electrode, and the interaction of DNA with the complex have been investigated. The experiments indicate that the electrode reaction of Cu(II)L₂ is an irreversible surface electrochemical reaction and that the reactant is of adsorbed character. In the presence of DNA, the formation of the electrochemically non-active complexes Cu(II)L₂-DNA, results in the decrease of the peak current of Cu(II)L₂. Based on the electrochemical behavior of the Cu(II)L₂ with DNA, binding by electrostatic interaction is suggested and a new method for determining nucleic acid is proposed. Under the optimum conditions, the decrease of the peak current is in proportional to the concentration of nucleic acids in the range from 3 × 10⁻⁸ to 3 × 10⁻⁶ g · mL⁻¹ for calf thymus DNA, from 1.6 × 10⁻⁸ to 9.0 × 10⁻⁷ g · mL⁻¹ for fish sperm DNA, and from 3.3 × 10⁻⁸ to 5.5 × 10⁻⁷ g · mL⁻¹ for yeast RNA. The detection limits are 3.3 × 10⁻⁹, 6.7 × 10⁻⁹ and 8.0 × 10⁻⁹ g · mL⁻¹, respectively. The method exhibits good recovery and high sensitivity in synthetic samples and in real samples.     

Simultaneous voltammetric measurement of ascorbic acid and dopamine on poly(caffeic acid)-modified glassy carbon electrode

A poly(caffeic acid) thin film was deposited on the surface of a glassy carbon electrode by potentiostatic technique in an aqueous solution containing caffeic acid. The poly(caffeic acid)-modified electrode was used for the determination of ascorbic acid (AA), dopamine (DA), and their mixture by cyclic voltammetry. This modified electrode exhibited a potent and persistent electron-mediating behavior followed by well-separated oxidation peaks toward AA and DA at a scan rate of 10 mV s⁻¹ with a potential difference of 135 mV, which was large enough to determine AA and DA individually and simultaneously. The catalytic peak current obtained was linearly dependent on the AA and DA concentrations in the range of 2.0 × 10⁻⁵−1.2 × 10⁻³ and 1.0 × 10⁻⁶−4.0 × 10⁻⁵ mol L⁻¹ in 0.15 mol L⁻¹ phosphate buffer (pH 6.64). The detection limits for AA and DA were 9.0 × 10⁻⁶ and 4.0 × 10⁻⁷ mol L⁻¹, respectively. The modified electrode shows good sensitivity, selectivity, and stability and has been applied to the determination of DA and AA in real samples with satisfactory results.     

Determination of trace rare earth elements by inductively coupled plasma optical emission spectrometry after preconcentration with immobilized nanometer titanium dioxide

A simple and sensitive method is presented for the determination of dopamine with a nanoscale ceria ion-selective CMC (carboxymethyl cellulose) membrane electrode by means of the Belousov–Zhabotinsky oscillating chemical reaction. The electrode exhibits excellent potential response. If the concentration of dopamine is in the range of 4.9 × 10⁻⁵ to 2.4 × 10⁻⁷ mol · L⁻¹, the change in oscillating amplitude is proportional to the concentration of dopamine, with a correlation coefficient of 0.9987 and a standard deviation of 0.17%. A recovery of 97.5–105.0% was obtained. Interference was also studied. The use of a nanoscale ceria ion-selective membrane-working electrode improved the sensitivity of the determination method.     

Preconcentration and Voltammetric Determination of the Antihypertensive Doxazosin on a C8 Modified Carbon Paste Electrode

 An electrochemical study of the doxazosin oxidative process at carbon paste electrodes using different voltammetric techniques has been carried out. The process is irreversible and controlled by adsorption, giving rise to an oxidation wave around 1.0 V in citric acid-citrate buffer (pH 3.0). A mechanism based on the oxidation of the amine group is postulated. Two methods based on adsorptive stripping (AdS) of doxazosin at the C₈-modified carbon paste electrode (C₈-MCPE), before its voltammetric determination, are studied, using differential pulse voltammetry (DPV) and square wave voltammetry (SWV) as redissolution techniques. By means of AdS-DPV and C₈-MCPE, doxazosin can be determined over the 1.0 × 10⁻⁹ to 3.0 × 10⁻⁸ mol L⁻¹ range with a variation coefficient of 2.2% (2.0 × 10⁻⁸ mol L⁻¹) and a limit of detection of 7.4 ×10⁻¹⁰ mol L⁻¹. If AdS-SWV is used, a linear range from 1.0 × 10⁻⁹ to 4.0 × 10⁻⁸ mol L⁻¹ is obtained, the variation coefficient being 2.8% (2.0 × 10⁻⁸ mol L⁻¹, and the limit of detection reached 7.7 × 10⁻¹⁰ mol L⁻¹. The AdS-DPV procedure was applied to the determination of doxazosin in urine and formulations. Received March 13, 1999. Revision December 23, 1999.     

FAD-modified SiO2/ZrO2/C ceramic electrode for electrocatalytic reduction of bromate and iodate

SiO₂/ZrO₂/C carbon ceramic material with composition (in wt%) SiO₂ = 50, ZrO₂ = 20, and C = 30 was prepared by the sol–gel-processing method. A high-resolution transmission electron microscopy image showed that ZrO₂ and the graphite particles are well dispersed inside the matrix. The electrical conductivity obtained for the pressed disks of the material was 18 S cm⁻¹, indicating that C particles are also well interconnected inside the solid. An electrode modified with flavin adenine dinucleotide (FAD) prepared by immersing the solid SiO₂/ZrO₂/C, molded as a pressed disk, inside a FAD solution (1.0 × 10⁻³ mol L⁻¹) was used to investigate the electrocatalytic reduction of bromate and iodate. The reduction of both ions occurred at a peak potential of −0.41 V vs. the saturated calomel reference electrode. The linear response range (lrr) and detection limit (dl) were: BrO₃ ⁻, lrr = 4.98 × 10⁻⁵–1.23 × 10⁻³ mol L⁻¹ and dl = 2.33 μmol L⁻¹; IO₃ ⁻, lrr = 4.98 × 10⁻⁵ up to 2.42 × 10⁻³ and dl = 1.46 μmol L⁻¹ for iodate.     

Covalent Modification of Glassy Carbon Electrode with L-Cysteine for the Determination of Acetaminophen

A novel L-cysteine film modified electrode has been fabricated by means of an electrochemical oxidation procedure, and it was successfully applied to the electrochemical determination of acetaminophen. This method utilizes the electrooxidation of amines to their analogous cation radicals to form a chemically stable covalent linkage between the nitrogen atom of the amine and edge plane sites at the glassy carbon electrode surface. The electrochemical behaviour of acetaminophen at the film electrode was investigated in 0.1 mol L⁻¹ phosphate buffer (pH 6.20). It was found that the redox peak current of acetaminophen was enhanced greatly on the film electrode. Linearity between the oxidation peak current and the acetaminophen concentration was obtained in the range of 1.0 × 10⁻⁴–2.0 × 10⁻⁷ mol L⁻¹ with a detection limit of 5.0 × 10⁻⁸ mol L⁻¹. For seven parallel detections of 1.0 × 10⁻⁵ mol L⁻¹ acetaminophen, the relative standard deviation (RSD) was 1.46%, suggesting that the film electrode has excellent reproducibility. Application to the determination of acetaminophen in drug tablets and human urine demonstrated that the film electrode has good stability and high sensitivity.     

Chemometrics to evaluate the quality of water sources for human consumption

Multilayer films of multiwalled carbon nanotubes (MWNTs) were homogeneously and stably assembled on a glassy carbon (GC) electrode using the layer-by-layer (LBL) method based on electrostatic interaction between MWNTs (negatively charged) and a biopolymer chitosan (CHIT) (positively charged). Scanning electron microscopy (SEM) image of the resulting {CHIT/MWNTs}₉ film indicated that the substrate was mostly covered with MWNTs in the form of small bundles or single nanotubes. The multilayer film was used to study the electrocatalytic oxidation of NADH. The assembled {CHIT/MWNTs}₉/GC electrode could decrease the oxidation overpotential of NADH by more than 350 mV. The {CHIT/MWNTs}₉/GC electrode exhibited a wide linear response range of 8 × 10⁻⁷ to 1.6 × 10⁻³ mol · L⁻¹ with a correlation coefficient of 0.997 for the detection of NADH. The response time and detection limit (S/N = 3) were determined to be 3 s and 0.3 × 10⁻⁶ mol · L⁻¹, respectively. Another attractive characteristic was that the method was simple and the assembled {CHIT/MWNTs}₉/GC electrode was highly stable.     

Determination of sulfanilamide based on the Mn(II)-catalyzed oscillating chemical reaction

A convenient and sensitive method for determination of sulfanilamide (SNA) was described based on the Mn(II)-catalyzed oscillating chemical reaction. Under optimum conditions, a linear relationship existed between the changes of oscillating period or amplitude and the negative of logarithm of SNA concentration in the range of 4.27 × 10⁻⁸ mol ·L⁻¹ ∼ 7.41 × 10⁻⁶ mol ·L⁻¹ (RSD, 0.85%) and 9.33 × 10⁻⁸ mol ·L⁻¹ ∼ 3.02 × 10⁻⁶ mol ·L⁻1 (RSD, 1.08%), respectively. The lower limit of detection was found to be 2.69 × 10⁻⁸ mol ·L⁻¹ and 6.03 × 10⁻⁸ mol ·L⁻¹, respectively.      

Fluorimetric determination of traces of europium(III) using a new chelator and acetate or phosphate in dimethylsulfoxide as enhancers

A new Schiff-base ligand [N, N′, N″-Tri- (2,4-dihydroxyacetophenone) – triaminotriethylamine (TDATA)] with a tripodal structure was synthesized. Its fluorescence intensity with the europium(III) complex was increased about 178-fold in the presence of sodium acetate (NaAc) and about 126-fold in the presence of sodium phosphate (Na₃PO₄) solution. After adding the organic solvent dimethylsulfoxide (DMSO) to the above system, which leads to Eu³⁺ the fluorescence was further enhanced about 12-fold. Spectrofluorimetric determination of trace amounts of Eu³⁺ based on the phenomenon was performed. The excitation and emission wavelength is 365 nm and 615 nm, respectively. Under optimum conditions, the fluorescence intensities vary linearly with the concentration of Eu³⁺ in the range of 4.9 × 10⁻¹²–3.2 × 10⁻⁶ mol · L⁻¹ with a detection limit of 4.5 × 10⁻¹² mol · L⁻¹ (for the TDATA-NaAc-DMSO system) or 6.2 × 10⁻¹¹–8.6 × 10⁻⁶ mol · L⁻¹ with a detection limit of 6.0 × 10⁻¹¹ mol · L⁻¹ (for the TDATA-Na₃PO₄-DMSO system). Interferences of some rare earth metals and other inorganic ions are described. The method is a selective, sensitive, rapid and simple analytical procedure for the determination of europium(III) in a high purity yttrium oxide and synthetic sample. The mechanism for the fluorescence enhancement is also discussed.     

Determination of hemoglobin at a novel NH2/ITO ion implantation modified electrode

A novel electrode was prepared by implanting NH₂ ⁺ into an ITO film (NH₂/ITO). Gold nanoparticles were deposited on the surface of NH₂/ITO electrode. The NH₂/ITO and Au/NH₂/ITO electrodes were used to determine hemoglobin (Hb) immobilized on the electrodes surfaces. The relationship of the reductive peak current value of Hb among different electrodes was: Hb/ITO:Hb/Au/ITO:Hb/NH₂/ITO:Hb/Au/NH₂/ITO=1:1.5:2:4. The linkage between the –NH₂ implanted into ITO film and the –COOH of Hb was recognized to be the reason for the increase of active Hb coverage on NH₂/ITO electrode compared with the ITO electrode. Increase of active Hb coverage on Au/NH₂/ITO compared with Au/ITO was attributed to the different amount of gold nanoparticles deposited. The determination of Hb at an Au/NH₂/ITO electrode was optimized. Calibration curve was obtained over the range of 1.0 × 10⁻⁸ – 1.0 × 10⁻⁶ mol · L⁻¹ with a detection limit of 1.0 × 10⁻⁸ mol · L⁻¹. Results showed that the novel NH₂/ITO and Au/NH₂/ITO electrodes exhibited good stability, reproducibility besides better electrochemical performance. Correspondence: Jing Bo Hu, Department of Chemistry, Beijing Normal University, Beijing 100875, China     

Flow-injection analysis for the determination of total inorganic carbon and total organic carbon in water using the H2O2–luminol–uranine chemiluminescent reaction

In the presence of carbonate and uranine, the chemiluminescent intensity from the reaction of luminol with hydrogen peroxide was dramatically enhanced in a basic medium. Based on this fact and coupled with the technique of flow-injection analysis, a highly sensitive method was developed for the determination of carbonate with a wide linear range. The method provided the determination of carbonate with a wide linear range of 1.0 × 10⁻¹⁰–5.0 × 10⁻⁶ mol L⁻¹ and a low detection limit (S/N = 3) of carbonate of 1.2 × 10⁻¹¹ mol L⁻¹. The average relative standard deviation for 1.0 × 10⁻⁹–9.0 × 10⁻⁷ mol L⁻¹ of carbonate was 3.7% (n = 11). Combined with the wet oxidation of potassium persulfate, the method was applied to the simultaneous determination of total inorganic carbon (TIC) and total organic carbon (TOC) in water. The linear ranges for TIC and TOC were 1.2 × 10⁻⁶–6.0 × 10⁻² mg L⁻¹ and 0.08–30 mg L⁻¹ carbon, respectively. Recoveries of 97.4–106.4% for TIC and 96.0–98.5% for TOC were obtained by adding 5 or 50 mg L⁻¹ of carbon to the water samples. The relative standard deviations (RSDs) were 2.6–4.8% for TIC and 4.6–6.6% for TOC (n = 5). The mechanism of the chemiluminescent reaction was also explored and a reasonable explanation about chemical energy transfer from luminol to uranine was proposed. Figure Chemiluminescence profiles in batch system. 1, Injection of 100 μL of K₂CO₃ into 1.0 mL luminol-1.0 mL H₂O₂ solution; 2-3 and 4-5, Injection in sequence of 100 μL of K₂CO₃ and 100 μL of uranine into 1.0 ml luminol-1.0 mL H₂O₂ solution; C_luminol = 1.0 × 10⁻⁷ mol/L, C_H2O2 = 1.0 × 10⁻⁵ mol/L, C_uranine = 1.0 × 10⁻⁵ mol/L, C_K2CO3 = 1.0 × 10⁻⁷ mol/L except for 4-5 where C_K2CO3 = 1.0 × 10⁻⁴ mol/L     

Electrochemical behavior and determination of epinephrine at a mercaptoacetic acid self-assembled gold electrode

The electrochemical behavior of epinephrine (EP) at a mercaptoacetic acid (MAA) self-assembled monolayer modified gold electrode was studied. The MAA/Au electrode is demonstrated to promote the electrochemical response of epinephrine by cyclic voltammetry. The possible reaction mechanism is also discussed. The diffusion coefficient D of EP is 6.85 × 10⁻⁶ cm² s⁻¹. In 0.1 mol L⁻¹ phosphate buffer (pH 7.20), a sensitive oxidation peak was observed at 0.177 V, and the peak current is proportional to the concentration of EP in the range of 1.0 × 10⁻⁵–2.0 × 10⁻⁴ mol L⁻¹ and 1.0 × 10⁻⁷–1.0 × 10⁻⁶ mol L⁻¹. The detection limit is 5 × 10⁻⁸ mol L⁻¹. The modified electrode is highly stable and can be applied to the determination of EP in practical injection samples. The method is simple, quick, sensitive and accurate.     

Application of an in situ plated lead film electrode to the analysis of testosterone by adsorptive stripping voltammetry

Adsorptive stripping voltammetry is a very sensitive and selective method for determination of drugs and organic substances in biological fluids. We have shown that determination of testosterone by adsorptive stripping voltammetry is possible using a lead film electrode. The lead film plating process and accumulation of testosterone were performed simultaneously from an acetate buffer solution of pH = 5.2 at a potential of −1.1 V. The measurements were carried out in undeaerated solutions. The detection limit was 9 × 10⁻⁹ mol L⁻¹ for an accumulation time of 120 s; the relative standard deviation for 1 × 10⁻⁷ mol L⁻¹ testosterone was 3.8%. The proposed voltammetric procedure for determination of testosterone could be applied to its determination in a pharmaceutical preparation and human urine samples directly without any separation steps.     

Electrochemical behavior of lead(II) at poly(phenol red) modified glassy carbon electrode, and its trace determination by differential pulse anodic stripping voltammetry

Poly(phenol red) (denoted as PPR) films were electrochemically synthesized on the surface of a glassy carbon electrode (GCE) by cyclic voltammetry to obtain a chemically modified electrode (denoted as PPR-GCE). The growth mechanism of PPR films was studied by attenuated total reflection spectroscopy. This PPR-GCE was used to develop a novel and reliable method for the determination of trace Pb²⁺ by anodic stripping differential pulse voltammetry. At optimum conditions, the anodic peak exhibits a good linear concentration dependence in the range from 5.0 × 10⁻⁹ to 5.0 × 10⁻⁷ mol L⁻¹ (r = 0.9989). The detection limit is 2.0 × 10⁻⁹ mol L⁻¹ (S/N = 3). The method was employed to determine trace levels of Pb²⁺ in industrial waste water samples. Correspondence: Gongjun Yang, Ming Shen, College of Chemistry and Chemical Engineering, Yangzhou University, Yangzhou 225002, P.R. China     

Voltammetric Analysis of the Novel Atypical Antipsychotic Drug Quetiapine in Human Serum and Urine

The electrooxidative behaviour and determination of quetiapine (QTP), a dibenzothiazepine derivative and antipsychotic agent, on a glassy carbon disc electrode was investigated using cyclic (CV), linear sweep (LSV), differential pulse (DPV) and Osteryoung square wave voltammetry (OSWV). Fully validated DP and SW voltammetric procedures are described for the determination of QTP. QTP in pH 3.5 acetate buffer solution presents a well-defined anodic response, studied by the proposed methods. This main response was due to the irreversible, diffusion-controlled, one-electron and one-proton oxidation of the aliphatic nitrogen of the piperazine ring. Under optimal conditions, a detection limit of 4.0 × 10⁻⁸ mol L⁻¹ for DPV and 1.33 × 10⁻⁷ mol L⁻¹ for OSWV, and a linear calibration graph in the range from 4.0 × 10⁻⁶ to 2.0 × 10⁻⁴ mol L⁻¹ were obtained for both methods. The procedure was successfully applied to the determination of the drug in tablets, human serum and human urine with good recoveries. The detection limits were 6.20 × 10⁻⁷ mol L⁻¹ and 5.92 × 10⁻⁷ mol L⁻¹ in human serum and 1.44 × 10⁻⁷ mol L⁻¹ and 1.31 × 10⁻⁶ mol L⁻¹ in human urine, for the DPV and OSWV method, respectively.     

Voltammetric detection of paraquat pesticide on a phthalocyanine-based pyrolitic graphite electrode

This work describes the application of an ordinary pyrolitic graphite electrode modified by metallophthalocyanine allied to square wave voltammetry for the study of the electrochemical behavior of the herbicide paraquat and the development of a method for its analytical determination in natural water samples. Preliminary experiments indicated that the best responses, considering the intensities of the current and voltammetric profile for the paraquat reduction process, were obtained when the electrode modified by cobalt phthalocyanine was employed, which had a better catalytic activity as a result of this modification compared with that for an unmodified electrode and electrodes modified by iron, manganese and the acid form of the phthalocyanines. Studies of the concentration of cobalt phthalocyanine and the adsorption time showed that 1.0 × 10⁻⁴ mol L⁻¹ cobalt phthalocyanine with an adsorption time of 10 min was sufficient to obtain reliability and stability of modification for employment in the development of the electroanalytical procedure for paraquat determination in natural water samples. The variation in pH of a 0.10 mol L⁻¹ Britton–Robinson buffer solution and the square wave parameters indicated that the best conditions to reduce paraquat were pH 7.0, a frequency of 100 s⁻¹, a scan increment of 2 mV and a square wave amplitude of 50 mV. Under such conditions, the variation of paraquat concentrations from 5.00 × 10⁻⁷ to 2.91 × 10⁻⁵ mol L⁻¹ showed a linear relation, with detection and quantification limits of 26.53 and 88.23 μg L⁻¹; those values were lower than the maximum limits for drinking water permitted by the Brazilian Environmental Council (100 μg L⁻¹), indicating that the method could be employed to analyze paraquat in drinking water samples.     

Determination of Tannic Acid by Flow Injection Analysis with Inhibited Chemiluminescence Detection

A novel flow injection procedure has been developed for the determination of tannic acid based on the inhibition of the chemiluminescences in luminol-H₂O₂-Manganese tetrasulfonatophthalocyanine (MnTSPc) system by tannic acid. The method is simple, rapid and sensitive with a detection limit of 8 × 10⁻¹⁰ mol·L⁻¹ and a linear range of 7 × 10⁻⁹–5 × 10⁻⁶ mol·L⁻¹. The relative standard deviation is 1.9% for eleven measurements of 5 × 10⁻⁷ mol·L⁻¹ tannic acid. The method has been successfully applied to the determination of tannic acid in real Chinese gall and hop pellets samples.