ZnS/CdS复合窗口层对CdTe太阳能电池短波光谱响应的影响

采用磁控溅射法制备了ZnS/CdS复合窗口层,并将其应用于CdTe太阳能电池。对所制备薄膜的形貌和结构等进行了研究。测试了具有不同窗口层的CdTe太阳电池的量子效率和光Ⅰ-Ⅴ特性,分析了ZnS薄膜制备条件对CdTe电池器件性能影响;研究了CdS薄膜厚度和ZnS/CdS复合窗口层对短波区透过率以及CdTe太阳电池的光谱响应的影响。着重研究了具有ZnS/CdS复合窗口层的CdTe太阳电池的短波光谱响应。结果表明,CdS窗口层厚度从100 nm减至50 nm后,其对短波区光子透过率平均提高了18.3%,CdTe太阳电池短波区光谱响应平均提高了27.6%。衬底温度250 ℃条件下制备的ZnS晶粒尺寸小于室温下制备的ZnS。具有ZnS/CdS复合窗口层的CdTe电池中,采用衬底温度250 ℃沉积ZnS薄膜来制备窗口层的电池器件,其性能要优于室温下沉积ZnS制备窗口层的电池器件。这说明晶粒尺寸的大小对电子输运有一定影响。在相同厚度CdS的前提下,具有ZnS/CdS复合窗口层的CdTe电池比具有CdS窗口层在短波的光谱响应提高了约2%。这说明ZnS/CdS复合窗口层能够做到减少对短波光子的吸收,从而使更多的光子被CdTe电池的吸收层吸收。     

Investigation of the effect of CdCl2 processing on vacuum deposited CdS/CdTe thin film solar cells by DLTS

Thin film CdS/CdTe solar cells have been prepared by conventional vacuum deposition technique. Deep level transient spectroscopy (DLTS), temperature and frequency dependent capacitance-voltage (C-V) measurements were utilised to investigate the performance limiting defect states in the CdTe layer subjected to the post deposition treatments such as CdCl₂-dipping and/or annealing in air. Five hole traps, all of which have been previously reported in the literature, were identified in as-grown CdTe at 0.19, 0.20, 0.22, 0.30 and 0.40 eV above the valence band. A single hole trap level has been evidenced at 0.45 eV after both post deposition heat and CdCl₂ treatments.     

Short-circuit current improvement in CdTe solar cells by combining a ZnO buffer layer and a solution back contact

Conventional CdTe solar cells have a CdS window layer, in which an absorption loss of photons with more than 2.4 eV occurs through the CdS layer. A thinner CdS layer was applied to enhance light transmission and a ZnO buffer layer with a band gap of 3.3 eV was introduced to suppress shunting through the thinner CdS window layer. A 100-nm thick ZnO layer sputter-deposited at 300 °C had uniform coverage on a transparent conductive oxide (TCO) after a subsequent high-temperature process. The ZnO layer was effective in preventing shunting through the CdS window layer so that the open-circuit voltage and fill factor of the CdTe solar cells were recovered and the short-circuit current was enhanced over that of the conventional CdTe solar cell. In the ZnO/CdS/CdTe configuration, the short-circuit current was further improved throughout the visible wavelength region by replacing the Cu-metal contact with a Cu solution contact. As a result the short-circuit current from 21.7 to 26.1 mA/cm² and the conversion efficiency of the CdTe solar cell increased from 12 to 15% without antireflective coating. Our result indicates that the Cu solution back contact is a critical factor for achieving a higher cell efficiency in addition to ZnO buffer layer.     

Recombination-induced voltage-dependent photocurrent collection loss in CdTe thin film solar cell

Recently, the efficiency of CdTe thin film solar cell has been improved by using new type of window layer Mg_xZn_1-xO (MZO). However, it is hard to achieve such a high efficiency as expected. In this report a comparative study is carried out between the MZO/CdTe and CdS/CdTe solar cells to investigate the factors affecting the device performance of MZO/CdTe solar cells. The efficiency loss quantified by voltage-dependent photocurrent collection efficiency (η_C(V')) is 3.89% for MZO/CdTe and 1.53% for CdS/CdTe solar cells. The higher efficiency loss for the MZO/CdTe solar cell is induced by more severe carrier recombination at the MZO/CdTe p—n junction interface and in CdTe bulk region than that for the CdS/CdTe solar cell. Activation energy (E_a) of the reverse saturation current of the MZO/CdTe and CdS/CdTe solar cells are found to be 1.08 eV and 1.36 eV, respectively. These values indicate that for the CdS/CdTe solar cell the carrier recombination is dominated by bulk Shockley—Read—Hall (SRH) recombination and for the MZO/CdTe solar cell the carrier recombination is dominated by the p—n junction interface recombination. It is found that the tunneling-enhanced interface recombination is also involved in carrier recombination in the MZO/CdTe solar cell. This work demonstrates the poor device performance of the MZO/CdTe solar cell is induced by more severe interface and bulk recombination than that of the CdS/CdTe solar cell.     

Performance improvement in CdTe solar cells by modifying the CdS/CdTe interface with a Cd treatment

The performance of n-CdS/p-CdTe solar cells is often degraded under light soaking or thermal stress, even though the technology of CdTe solar cells is close to a commercial level. The Cu diffusion from a Cu back contact to a CdS window layer might degrade the cell's performance. To prevent the Cu diffusion, a very-thin intrinsic CdTe layer was introduced at the n-CdS/p-CdTe interface by depositing a very-thin Cd metal layer on the CdS film and converting the Cd metal into intrinsic CdTe during p-CdTe deposition at high temperature. By the Cd treatment on CdS surface, pinholes or voids were eliminated at the CdS/CdTe and the intermixing of Te and S at the interface was much suppressed. The depletion width was much increased and the intensity of LTPL peak was increased. The analysis suggested that an intrinsic CdTe interlayer was formed and the surface recombination rate was suppressed by the intrinsic interlayer. As a result, the short circuit current of the CdTe solar cell was significantly increased due the increased current gain in the blue wavelength region. The thermal stability of the CdTe solar cell was also greatly improved and the Cu diffusion was retarded by the intrinsic CdTe interlayer at the n-CdS/p-CdTe.     

化学水浴法制备大面积CdS薄膜及其光伏应用

采用化学水浴法制备了大面积CdS多晶薄膜,研究了薄膜的形貌、结构和光学性质,结果表明,大面积CdS多晶薄膜具有良好的均匀性,通过优化CdS多晶薄膜,制成了不同CdS窗口层厚度的CdTe小面积太阳电池,减薄CdS薄膜可有效提高器件的短路电流,改善器件性能.随后,在面积30cm×40cm的衬底上制备了全面积为993.6cm²的CdTe太阳电池组件,其27个集成单元的电学性质较为均匀,太阳电池组件的光电转换效率8.13%. 关键词： 化学水浴法(CBD) CdS薄膜 CdTe太阳电池 CdTe太阳电池组件     

Short‐circuit current improvement of CuGaSe2 solar cells with a ZnS/(Zn,Mg)O buffer combination

CuGaSe₂ (CGS) thin‐film solar cells were prepared with an in‐line co‐evaporation process and the established buffer combination CdS/i‐ZnO was replaced by ZnS/(Zn,Mg)O. We obtained functional CGS solar cells with a strong gain in the short‐circuit current density as compared to the CdS/i‐ZnO buffer reference cells. The enhanced current density is a result of improved transmission in the wavelength region between 330 nm and 550 nm of the ZnS/(Zn,Mg)O buffer combination as compared to CdS/i‐ZnO. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Investigation of CdS and CdTe thin films and influence of CdCl2 on CdTe/CdS structure

CdTe/CdS heterojunction solar cell structure has been fabricated using simple, easy and low-cost methods. To fabricate this structure, CdS and CdTe thin films are deposited onto FTO-coated conducting glass substrates by chemical bath deposition (CBD) and electrodeposition method, respectively. The optimized growth conditions are chosen for both CdS and CdTe films by investigating the optical, structural and morphological properties of both the as-deposited and annealed films. Optical measurement showed that CdS films have higher transmittance and lower absorbance, and CdTe films have lower transmittance and higher absorbance in the near infrared region. The band gap of CdS films is estimated to lie in the range 2.29–2.41 eV and that of CdTe films is in the range 1.53–1.55 eV. X-ray diffraction (XRD) study reveals that CdS and CdTe films are polycrystalline with preferential orientation of (1 1 1) plane. Scanning electron microscopy (SEM) study reveals that both films are smooth, void-free and uniformly distributed over the surface of the substrate. Fabricated CdTe/CdS structure showed the anticipated rectifying behaviour, and the rectifying behaviour is observed to improve due to CdCl₂ treatment.     

Preparation of chemically deposited thin films of CdS/PbS solar cell

The present paper reports the preparation of a solar cell which has a cross-sectional scheme: ITO/CdS/PbS, containing a commercially transparent conductive ITO; chemically deposited n-type CdS (340 nm) and absorbed layer of p-type PbS (1400 nm). The structural and optical properties of the constituent films are presented. X-ray diffraction showed that all of the thin films are polycrystalline. Using scanning electron microscopy, the present study revealed that the films have uniform surface morphology over the substrate. The solar cell was characterized by determining the open circuit voltage, short-circuit current density, and J–V under 40 mW/cm² solar radiation. The efficiency of the solar cells was 1.35%, which is much higher (0.041, 0.5 and 0.1–0.4%) and slightly smaller (1.65%) than some solar cells reported in the literature.     

Exchange coupling in CoO–Co bilayer

In this work, exchange bias and coercivity enhancement in ferromagnet (FM)–antiferromagnet (AFM) bilayer have been investigated. CoO film (50 nm) was deposited by sputtering with a relatively high oxygen partial pressure. The deposited films were subsequently annealed at varied temperature up to 973 K in the air atmosphere. The CoO film shows a disordered structure in the as-deposited state and an increase of crystallinity after annealing characterized by XRD and Raman spectra. A 40-nm Co film was deposited on the as-deposited CoO and annealed films. The Co–CoO bilayer shows a large exchange bias up to 1600 Oe and relatively high coercivity up to 3200 Oe (H_C−) at 5 K, which is much larger than that of crystalline Co–CoO bilayer films without any treatment. The spin glass behavior combined with increasing crystallinity, surface roughness of CoO after annealing may be attributed to the large exchange bias and high coercivity.     

Highly porous nickel oxide thin films prepared by a hydrothermal synthesis method for electrochromic application

We report NiO nanowall thin films prepared by a facile hydrothermal synthesis method and their electrochromic application. The as-prepared porous nanowall NiO thin films show a highly porous structure built up by many interconnected nanoflakes with a thickness of about 30 nm. The electrochromic performances of the NiO films are characterized by means of UV–vis spectroscopy and cyclic voltammetry (CV) measurements. The effect of the annealing temperature on electrochromic properties is discussed. The NiO nanowall film annealed at 300 °C exhibits much better electrochromic performance than those counterparts annealed at higher temperature. The film annealed at 300 °C exhibits a noticeable electrochromism with reversible color changes from transparent to brown dark and presents a transmittance variation with 77% at 550 nm. The NiO nanowall film also shows good reaction kinetics with fast switching speed, and the coloration and bleaching times are 3 s and 4 s, respectively. The improved electrochromic performances are due to the porous morphological characteristics with fast ion and electron transfer resulting in fast reaction kinetics and high color contrast.     

CdTe太阳电池前电极SnO2:F/SnO2复合薄膜性能分析

减薄CdS窗口层是提高CdS/CdTe太阳电池转换效率的有效途径之一,减薄窗口层会对器件造成不利的影响,因此在减薄了的窗口层与前电极之间引入过渡层非常必要.利用反应磁控溅射法在前电极SnO₂:F薄膜衬底上制备未掺杂的SnO₂薄膜形成过渡层,并将其在N₂/O₂=4 ∶1,550 ℃环境进行了30 min热处理,利用原子力显微镜、X射线衍射仪、紫外分光光度计对复合薄膜热处理前后的形貌、结构、光学性能进行了表征,同时分析了复     

Spectroscopic analysis of CIGS2/CdS thin film solar cell heterojunctions on stainless steel foil

This paper presents a spectroscopic analysis of the interface between a CuIn_1−xGa_xS₂ (CIGS2) absorber and a CdS buffer layer on stainless steel foil by Auger electron spectroscopy (AES), inverse photoemission spectroscopy (IPES) and photoelectron spectroscopy (PES) such as X-ray photoelectron spectroscopy (XPS), and ultraviolet photoelectron spectroscopy (UPS). By combining these spectroscopic techniques, detailed information about the electronic and chemical properties of the CIGS2 surface and the CdS/CIGS2 interface can be obtained. The gallium concentration in CIGS2 films was found to increase continuously towards the Mo back contact. XPS analysis showed the presence of KCO₃ on the surface of CdS, deposited on etched and un-oxidized samples indicating diffusion of potassium. No potassium was observed on oxidized as well as samples having thicker CdS (50 nm) indicating the effectiveness of oxidation and chemical bath deposition (CBD) process in cleaning the sample surface effectively. In addition, investigation of the electronic level alignment at the interface has been carried out by combining PES and IPES. Conduction band offset of −0.45 (±0.15) eV and a valence band offset of −1.06 (±0.15) eV were measured. These unfavorable conditions limit efficiency of CIGS2 thin film solar cells.     

Nanotribological behavior of ZnO films prepared by atomic layer deposition

We used atomic layer deposition to form ZnO thin-film coatings on Si substrates and then evaluate the effect of pile-up using the nanoscratch technique under a ramped mode. The wear volume decreased with increasing annealing temperature from room temperature to 400 °C for a given load. Elastic-to-plastic deformation occurred during sliding scratch processing between the groove and film for loading penetration of 30 nm. The onset of non-elastic behavior and greater contact pressure were evident for loading penetration of 150 nm; thus, full plastic deformation occurred as a result of a substrate effect. We suspect that elastic–plastic failure events were related to edge bulging between the groove and film, with elastic–plastic deformation attributable to adhesion discontinuities and/or cohesion failure of the ZnO films.     

Photoluminescence quenching of CdTe/CdS core-shell quantum dots in aqueous solution by ZnO nanocrystals

Photoluminescence (PL) properties of 3-mercaptopropionic acid (MPA) coated CdTe/CdS core-shell quantum dots (QDs) in aqueous solution in the presence of ZnO colloidal nanocrystals were studied by steady-state and time-resolved PL spectroscopy. The PL quenching of CdTe/CdS core-shell QDs with addition of purified ZnO nanocrystals resulted in a decrease in PL lifetime and a small red shift of the PL band. It was found that CdTe(1.5 nm)/CdS type II core-shell QDs exhibited higher efficiency of PL quenching than the CdTe(3.0 nm)/CdS type I core-shell QDs, indicating an electron transfer process from CdTe/CdS core-shell QDs to ZnO nanocrystals. The experimental results indicated that the efficient electron transfer process from CdTe/CdS core-shell QDs to ZnO nanocrystals could be controlled by changing the CdTe core size on the basis of the quantum confinement effect.     

Photovoltaic characteristics of hybrid MEH-PPV-nanoparticles compound

Organic solar cell research has vastly developed in recent years. These organic solar cells however are still limited to low power conversion efficiencies. This has led to the generation of photovoltaic cells based on hybrid nanoparticle-organic polymer materials. The hybrid solar cell has the potential of bridging the efficiency gap which is present in organic and inorganic semiconductor materials. This paper focuses on characterization of fabricated hybrid active layer consisting of organic polymer infused with semiconductor nanoparticles. The active layer was deposited on the substrate using the spin coating technique. Materials used in the active layer are poly (2-methoxy, 5-(2-ethyl hexyloxy) p-phenyl vinylene) MEH-PPV, cadmium telluride (CdTe) and cadmium sulphide (CdS). The fabricated solar cells with active layer of MEH-PPV only were found to have a power conversion efficiency of 0.1% for 1 W, hybrid cell with active layer of MEH-PPV/CdTe has power conversion efficiency of 0.15% for 1 W and hybrid cell with active layer of MEH-PPV/CdTe/CdS has power conversion efficiency of 0.18% for 1 W.     

Synthesis of high quality and monodisperse CdS:Mn/ZnS and CdS:Mn/CdS core–shell nanoparticles

CdS:Mn²⁺/ZnS and CdS:Mn²⁺/CdS core–shell nanoparticles were synthesized in aqueous medium via chemical precipitation method in an ambient atmosphere. Polyvinylpyrrolidone (PVP) was used as a capping agent. The effect of the shell (ZnS and CdS) thickness on CdS:Mn²⁺ nanoparticles was investigated. Inorganically passivated core/shell nanocrystals having a core (CdS:Mn²⁺) diameter of 4 nm and a ZnS-shell thickness of ∼0.5 nm exhibited improved PL intensity. Optimum concentration of doping ions (Mn²⁺) was selected through optical study. For all the core–shell samples two emission peaks were observed, the first one is band edge emission in the lower wavelength side due to energy transfer to the Mn²⁺ ions in the crystal lattice; the second emission is characteristic peak of Mn²⁺ ions (⁴T₁ → ⁶A₁). The XRD, TEM and PL results showed that the synthesized core–shell particles were of high quality and monodisperse.     

Co-sensitized quantum dot solar cell based on ZnO nanowire

An efficient photoelectrode is fabricated by sequentially assembled CdS and CdSe quantum dots (QDs) onto a ZnO-nanowire film. As revealed by UV-vis absorption spectrum and scanning electron microscopy (SEM), CdS and CdSe QDs can be effectively adsorbed on ZnO-nanowire array. Electrochemical impedance spectroscopy (EIS) measured demonstrates that the electron lifetime for ZnO/CdS/CdSe (13.8 ms) is calculated longer than that of ZnO/CdS device (6.2 ms), which indicates that interface charge recombination rate is reduced by sensitizing CdSe QDs. With broader light absorption range and longer electron lifetime, a power conversion efficiency of 1.42% is achieved for ZnO based CdS/CdSe co-sensitized solar cell under the illumination of one Sun (AM 1.5G, 100 mW cm⁻²).     

氧对于在Ar/O氛围下用近空间升华法制备的CdS薄膜的影响

采用近空间升华法（CSS）在氩/氧气氛中制备了硫化镉（CdS）多晶薄膜.利用XRD,XPS,AFM,UV-VIS光谱和四探针技术等测试和分析手段系统研究了氧对薄膜的成分、结构、光学和电学等性质的影响.结果表明,用近空间升华法制备的CdS薄膜具有六方相结构,膜层致密、均匀,平均晶粒大小约为40 nm,富硫.氧掺入后部分与镉生成氧化镉,并随着氧含量的增加,薄膜的成分有趋于化学计量比的趋势,光学带隙加宽,光暗电导比增加.此外,还利用扫描电镜（SEM）观察了CdS/CdTe断面结合光谱响应（QE）的结果讨论了氧对CdS/CdTe界面互扩散的影响.发现,随着CdS薄膜制备气氛中氧分压的升高,CdS/CdTe界面的互扩散程度降低,有利于提高器件在500—600 nm波长范围内的光谱响应.认为,氧含量的增加不但使CdS薄膜在光伏应用方面的质量得到改善,而且CdTe太阳电池器件中的CdS/CdTe界面也得到了优化. 关键词： CdS多晶薄膜 近空间升华法 窗口层 界面     

Numerical simulation of ultra-thin CdTe solar cells with a buffer layer of MoOx in the backwall configuration

The software of Solar Cell Capacitance Simulator (SCAPS) is used to investigate the performance of ultra-thin CdTe solar cells in the backwall configuration (glass/ITO/MoO_x/CdTe/CdS/SnO₂/Ag). The backwall structure utilizes ultra-thin CdTe absorber layer instead of CdS film facing light illumination, which eliminates the absorption of CdS in short-wavelength region and improves the blue response of CdTe. A buffer layer of MoO_x is added to modify the contact between CdTe and ITO, reducing the valence band barrier height and simultaneously forming an electron reflector, which can reduce electron-hole recombination at this contact. When the thickness of MoO_x is 2 nm, the simulation results show that an efficiency can reach up to 25.5% with high ITO work function and ideal interface recombination velocity.