甲苯气相选择氧化制苯甲醛 Ⅳ.助剂锂、钾、铯对V_2O_5/TiO_2催化剂性能的影响

在Ｖ２Ｏ５／ＴｉＯ２催化剂中分别添加Ｌｉ、Ｋ、Ｃｓ等碱金属离子，利用ＢＥＴ、ＸＲＤ、ＸＰＳ、Ｈ２－ＴＰＲ、Ｏ２－ＴＰＤ－ＭＳ和化学分析方法，研究了催化剂结构和性能的变化．结果表明，催化剂在添加不同碱金属离子后，其结构和表面活性氧发生了很大变化．Ｋ离子可以改善催化剂的活性、提高反应选择性；Ｌｉ离子能提高催化剂活性，但在相当宽的温度范围内使反应选择性下降；在６９３Ｋ以下，Ｃｓ离子对催化剂的活性和选择性均起抑制作用．     

Development of porosity in carbons from yeast grains by activation with alkali metal carbonates

Cellular structured activated carbon samples were prepared with the aid of alkali carbonates X2CO3 (X = Li, Na, K, Rb, or Cs) from dry bread yeast with a milling procedure. The resultant carbon possesses a very large adsorption amount even for supercritical methane. The activation with Cs2CO3 gave the greatest surface area of 2420 m2 g(-1) from the subtracting pore effect method. The activation efficiency of X2CO3 (X = Li, Na, K, Rb, and Cs) was associated with the order of Gibbs free energy of X2O (X = Li, Na, K, Rb, and Cs) which should play an important role in the gasification. The carbon activated with Rb2CO3 gave the greatest adsorption amount of supercritical methane of 90 mg g(-1) at 0.9 MPa at 303 K.     

氧化硅负载的固体碱上乙醛的气相缩合反应

在氧化硅负载的含碱金属固体碱催化剂上乙醛能有效地缩合生成丁烯醛及丁烯醇,反应具有中等转化率、较好的选择性(约90％)和稳定性.考察了不同反应条件对催化性能的影响,并对可能的反应活性相进行了探讨.     

Artificial ion channel formed by cucurbit[n]uril derivatives with a carbonyl group fringed portal reminiscent of the selectivity filter of K+ channels

Novel artificial ion channels (1 and 2) based on CB[n] (n = 6 and 5, respectively) synthetic receptors with carbonyl-fringed portals (diameter 3.9 and 2.4 A, respectively) can transport proton and alkali metal ions across a lipid membrane with ion selectivity. Fluorometric experiments using large unilamellar vesicles showed that 1 mediates proton transport across the membranes, which can be blocked by a neurotransmitter, acetylcholine, reminiscent of the blocking of the K+ channels by polyamines. The alkali metal ion transport activity of 1 follows the order of Li+ > Cs+ approximately Rb+ > K+ > Na+, which is opposite to the binding affinity of CB[6] toward alkali metal ions. On the other hand, the transport activity of 2 follows the order of Li+ > Na+, which is also opposite to the binding affinity of 2 toward these metal ions, but virtually no transport was observed for K+, Rb+, and Cs+. It is presumably because the carbonyl-fringed portal size of 2 (diameter 2.4 A) is smaller than the diameters of these alkali metal ions. To determine the transport mechanism, voltage-clamp experiments on planar bilayer lipid membranes were carried out. The experiments showed that a single-channel current of 1 for Cs+ transport is approximately 5 pA, which corresponds to an ion flux of approximately 3 x 107 ions/s. These results are consistent with an ion channel mechanism. Not only the structural resemblance to the selectivity filter of K+ channels but also the remarkable ion selectivity makes this model system unique.     

Multiple charging of poly(propylene glycol) by binary mixtures of cations in electrospray

Single, double and triple charging of poly(propylene glycol) (PPG) (Mn = 1900 g/mol) in the presence of binary mixtures of cations (Li+, Na+, K+, Cs+, and NH4+) under electrospray ionization (ESI) conditions were investigated. For these studies, sodium ion was selected as the reference cation, and the resulting ion-intensities were evaluated as a function of the [Na+]/[C+] ratio (where C+ is the other cation, i.e., Li+, K+, Cs+ and NH4+). A linear relationship was found between INa+/IC+)and [Na+]/[C+] (INa+ and IC+ stand for the intensity of the singly charged PPG molecules cationized with Na+ and C+ ions, respectively). The slope of the INa+/IC+--[Na+]/[C+] plot (alpha) indicates the binding selectivity of Na+ ions to PPG chains with respect to cation C+. In the case of the doubly charged PPG chains, the INaNa2+/INaC2+ and INaC2+/ICC2+ versus [Na+]/[C+] ratio also yield straight lines with slopes of approximately alpha/2 and 2alpha, respectively (INaNa2+, INaC2+ and ICC2+ are the intensity of the doubly charged PPG chains cationized with two Na+ ions, Na+ and C+ ions, and two C+ ions, respectively). Similarly, linear dependences with the [Na+]/[C+] ratio for the corresponding intensity ratios of the triply charged PPG were found. Based on the value of alpha, the selectivity of the cations was found to increase in the order of Li+ < Cs+ approximately Na+ < K+ approximately NH4+. The observed relative ion intensities are interpreted on the basis of the solution state equilibrium between PPG and the cations. In addition, the investigations showed that the abundances of the doubly and triply charged PPG-containing mixed cations can be optimized in a simple way using the value of alpha.     

Selectivity of alkali metal cations adsorption on controlled porous glasses

Alkali metal ions are adsorbed on controlled porous glasses from basic solutions. Narrow porous glasses show a relatively high selectivity with adsorption decreasing in the series Cs, K, Na, Li.     

Extraction equilibria of various metal picrates with 19-crown-6 between benzene and water. Effect of the extra methylene group on extraction ability and selectivity

The overall extraction equilibrium constants (K(ex)) of picrates of Li(+), Na(+), K(+), Rb(+), Cs(+), Ag(+), Tl(+), and Sr(2+)with 19-crown-6 (19C6) were determined between benzene and water at 25 degrees C. The K(ex) values were analyzed into the constituent equilibrium constants, i.e. the extraction constant of picric acid, the distribution constant of the crown ether, the formation constant of the metal ion-crown ether complex in water, and the ion-pair extraction constant of the complex cation with the picrate anion. The effects of an extra methylene group of 19C6 on the extraction ability and selectivity are discussed in detail by comparing the constituent equilibrium constants of 19C6 with those of 18-crown-6 (18C6). The K(ex) value of 19C6 for each metal ion is lower than that of 18C6, which is mostly attributed to the higher lipophilicity of 19C6. The extraction ability of 19C6 for the univalent metal ions decreases in the order Tl(+)>K(+)>Rb(+)>Ag(+)>Cs(+)>Na(+)Li(+), which is the same as that observed for 18C6. The difference in logK(ex) between the univalent metals is generally smaller for 19C6 than for 18C6. The extraction selectivity of 19C6 is governed by the selectivity in the ion-pair extraction, whereas that of 18C6 depends on both the selectivities in the ion-pair extraction and in the complexation in water.     

Ion exchange in reverse micelles

The distribution and dynamics of alkali cations inside Na-AOT reverse micelles have been investigated using Monte Carlo and molecular dynamics simulations. Water is modeled using the extended simple point charge (SPC/E) model. Simulations were carried out for alkali salts of Li+, Na+, K+, and Cs+ placed into the aqueous core of the reverse micelle, for situations corresponding to one and three molecules of added salt. In all cases, we observe that the larger K+ and Cs+ ions exchange with the Na+ counterion; however, the smaller Li+ ion prefers to remains solvated within the core of the reverse micelle. Our study reveals that the oil-water interface of the Na-AOT reverse micelle has the greatest selectivity toward Cs+ followed by K+ and Li+. A model based on enthalpic contributions illustrates that the solvation energies of the different cations in water control the ion-exchange process. The hydration number of the first water shell for Li+ situated in the aqueous core of the reverse micelle with radius R = 14.1 A was similar to that observed at infinite dilution in bulk water.     

Complexation of Calix[4]arene With Alkali Metal Cations: Conformational Binding Selectivity and Cation-π Driven Inclusion

Hartree-Fock, second order Møller-Plesset perturbation theory, and density functional theory calculations were carried out to analyse the complexation of calix[4]arene with cationic species including H + and the alkali metal cations (Li + , Na + , K + , Rb + , and Cs + ). Special emphasis has been placed on conformational binding selectivity, and on the structural characterization of the complexes. Li + and Na + cations are located in the calix[4]arene lower rim. The larger cations (K + , Rb + , and Cs + ) complex preferentially with the calix[4]arene cone conformer, and their endo (inclusive) complexation is driven by cation- ~ interactions, leading in the case of K + to a structure that reflects a preferential interaction with two phenol rings. The endo complexation of Cs + with calix[4]arene is in agreement with X-ray diffraction data.     

CO2 adsorption in mono-, di- and trivalent cation-exchanged metal-organic frameworks: a molecular simulation study

A molecular simulation study is reported for CO(2) adsorption in rho zeolite-like metal-organic framework (rho-ZMOF) exchanged with a series of cations (Na(+), K(+), Rb(+), Cs(+), Mg(2+), Ca(2+), and Al(3+)). The isosteric heat and Henry's constant at infinite dilution increase monotonically with increasing charge-to-diameter ratio of cation (Cs(+) < Rb(+) < K(+) < Na(+) < Ca(2+) < Mg(2+) < Al(3+)). At low pressures, cations act as preferential adsorption sites for CO(2) and the capacity follows the charge-to-diameter ratio. However, the free volume of framework becomes predominant with increasing pressure and Mg-rho-ZMOF appears to possess the highest saturation capacity. The equilibrium locations of cations are observed to shift slightly upon CO(2) adsorption. Furthermore, the adsorption selectivity of CO(2)/H(2) mixture increases as Cs(+) < Rb(+) < K(+) < Na(+) < Ca(2+) < Mg(2+) ≈ Al(3+). At ambient conditions, the selectivity is in the range of 800-3000 and significantly higher than in other nanoporous materials. In the presence of 0.1% H(2)O, the selectivity decreases drastically because of the competitive adsorption between H(2)O and CO(2), and shows a similar value in all of the cation-exchanged rho-ZMOFs. This simulation study provides microscopic insight into the important role of cations in governing gas adsorption and separation, and suggests that the performance of ionic rho-ZMOF can be tailored by cations.     

Monovalent ion adsorption at the muscovite (001)-solution interface: relationships among ion coverage and speciation, interfacial water structure, and substrate relaxation

The interfacial structure between the muscovite (001) surface and aqueous solutions containing monovalent cations (3 × 10(-3) m Li(+), Na(+), H(3)O(+), K(+), Rb(+), or Cs(+), or 3 × 10(-2) m Li(+) or Na(+)) was measured using in situ specular X-ray reflectivity. The element-specific distribution of Rb(+) was also obtained with resonant anomalous X-ray reflectivity. The results demonstrate complex interdependencies among adsorbed cation coverage and speciation, interfacial hydration structure, and muscovite surface relaxation. Electron-density profiles of the solution near the surface varied systematically and distinctly with each adsorbed cation. Observations include a broad profile for H(3)O(+), a more structured profile for Li(+) and Na(+), and increasing electron density near the surface because of the inner-sphere adsorption of K(+), Rb(+), and Cs(+) at 1.91 ± 0.12, 1.97 ± 0.01, and 2.26 ± 0.01 ?, respectively. Estimated inner-sphere coverages increased from ~0.6 to 0.78 ± 0.01 to ~0.9 per unit cell area with decreasing cation hydration strength for K(+), Rb(+), and Cs(+), respectively. Between 7 and 12% of the Rb(+) coverage occurred as an outer-sphere species. Systematic trends in the vertical displacement of the muscovite lattice were observed within ~40 ? of the surface. These include a <0.1 ? shift of the interlayer K(+) toward the interface that decays into the crystal and an expansion of the tetrahedral-octahedral-tetrahedral layers except for the top layer in contact with solution. The distortion of the top tetrahedral sheet depends on the adsorbed cation, ranging from an expansion (by ~0.05 ? vertically) in 3 × 10(-3)m H(3)O(+) to a contraction (by ~0.1 ?) in 3 × 10(-3) m Cs(+). The tetrahedral tilting angle in the top sheet increases by 1 to 4° in 3 × 10(-3) m Li(+) or Na(+), which is similar to that in deionized water where the adsorbed cation coverages are insufficient for full charge compensation.     

Nickel hexacyanoferrate membrane as a coated wire cation-selective electrode

Nickel hexacyanoferrates containing alkali metal cations as counter ions were used to prepare ion-selective electrodes for potentiometric sensing of intercalated species in the coated wire electrode (CWE) configuration. All the electrodes developed display a quasi-Nernstian response towards potassium ion, whereas the highest sensitivity is generally achieved when Cs+ is the counter cation in the sensing material. The selectivity constants of the electrodes were calculated by the matched potential method considering K+ as the primary ion. The selectivity order is Cs+ > K+ > Na+ > Li+ and reflects the effective dimension of the hydrated cations.     

Relative binding affinities of alkali metal cations to

The binding affinity and selectivity of a new ionophore, [1(8)]starand (1), toward alkali metal cations in methanol were examined through NMR titration experiments and free energy perturbation (FEP) and molecular dynamics simulations. The preference was determined to be K(+) > Rb(+) > Cs(+) > Na(+) > Li(+) in both FEP simulations and NMR experiments. The FEP simulation results were able to predict the relative binding free energies with errors less than 0.13 kcal/mol, except for the case between Li(+) and Na(+). The cation selectivity was rationalized by analyzing the radial distribution functions of the M-O and M-C distances of free metal cations in methanol and those of metal-ionophore complexes in methanol.     

The solvent extraction of alkali metal picrates with 4,13-N,N'-dibenzyl-4,13-diaza-18-crown-6

Extraction of alkali metal picrates with N,N'-dibenzyl-18-crown-6 was carried out, with dichloromethane as water-immiscible solvent, as a function [ligand]/[metal cation]. The extractability of metal picrates (Li(+), Na(+), K(+), Rb(+), Cs(+)) was evaluated as a function of [L]/[M(+)]. The extractability of complex cation-picrate ion pairs decreases in this sequence: Li(+)>Rb(+)>Cs(+)>K(+)>Na(+). The overall extraction equilibrium constants (K(ex)) for complexes of N,N'-dibenzyl-18-crown-6 with alkali metal picrates between dichloromethane and water have been determined at 25 degrees C. The values of the extraction constants (logK(ex)) were determined to be 10.05, 6.83, 7.12, 7.83, 6.73 for Li(+), Na(+), K(+), Rb(+) and Cs(+) compounds, respectively. DB186 shows almost 2-fold extractability against Li(+) compared to the other metal picrates, whereas it shows no obvious extractability difference amongst the other metal cations when [L]/[M(+)] is 0.2-1. However, an increasing extractability is observed for Cs(+) when [L]/[M(+)] [1].     

Li2Mg2Si4O10F2、H2Mn8O16•1.4H2O和Li1.3Ti1.7Al0.3(PO4)3在高浓度LiCl水溶液中的离子交换行为

研究了用功能材料Li2Mg2Si4O10F2 (LHT)、H2Mn8O16•1.4H2O (CRYMO)和Li1.3Ti1.7Al0.3(PO4)3 (LTAP)分别去除高浓度氯化锂水溶液中的杂质Fe3＋、K＋和Na＋.实验结果表明，这几种功能材料分别对溶液中的杂质Fe3＋、K＋和Na＋有很高的选择性，除杂效果明显.分析和研究了这几种功能材料在高浓度氯化锂水溶液中分别与Fe3＋、K＋和Na＋的交换行为.结果表明，在高浓度氯化锂溶液中这几种功能材料与杂质交换的动力学行为可近似用JMAK方程描述.     

五元交互体系Li+,Na+,K+//CO32-,Cl--H2O在298.15K的相平衡研究

针对西藏扎布耶盐湖卤水组成,采用等温溶解平衡法研究了五元交互体系Li+,Na+,K+//CO32-,Cl--H2O于298.15K时的相平衡,并绘制了相图(空间立体图和Li2CO3饱和的投影图).结果表明,该五元体系相图含有7个结晶区、13条单变量线和4个无变量点.7个结晶区由6个单盐结晶区和1个复盐结晶区组成,分别为LiCl·H2O,NaCl,KCl,Li2CO3,K2CO3·3/2H2O,Na2CO3·10H2O和NaKCO3·6H2O,没有形成固溶体和天然碱(Na2CO3·NaHCO3·2H2O).4个无变量点标记成K1,K2,K3和K4,所对应的平衡固相盐分别是:Li2CO3+NaKCO3·6H2O+Na2CO3·10H2O+KCl,Li2CO3+NaKCO3·6H2O+K2CO3·3/2H2O+KCl,Li2CO3+NaCl+KCl+LiCl·H2O和Li2CO3+NaCl+Na2CO3·10H2O+KCl.     

1^H、7^Li、23^Na、133^Cs NMR研究含氮大环醚双内酯和大环胺双内酰胺的配合性能

本文报道1^H、7^Li、23^Na、133^Cs NMR测定N, N'-二羧甲基大环醚双内酯(1-4)和大环胺双内酰胺(5), N-对甲苯磺酰基大环醚双内酯(6, 7), 4'-丹磺酰氨基苯并-18-冠-6(8)与Li^+、Na^+、K^+、Cs^+、Cd^2+和Pb^2+金属离子的配位作用, 并以非线性最小二乘法拟合计算了配合物的形成常数; 同时, 发展了一种用133^Cs NMR测量冠醚和碘离子竞争配合Cs^+的配合物形成常数的新技术。     

Na^+/CaO催化剂上的甲烷氧化偶联

研究了不同碱金属离子对CaO的促进作用,发现以Na~+的添加效果最好。在此基础上,研究了不同含钠化合物对CaO的促进作用,并用脉冲反应技术研究Na~+/CaO催化剂表面氧物种的特性及其作用。CaO表面上存在非选择性氧化的氧物种。Na~+对CaO的修饰作用是抑制非选择性氧化。当表面上的非选择性氧化的氧物种消耗后,体相的晶格氧会向表面迁移,以补充消耗掉的表面氧物种。消耗掉的表面氧物种也可由气相氧补充。CH_4脉冲和混合气脉冲说明仅靠[Na~+O~-]中心不足以使甲烷转化成C_2产物,必须有气相氧的参与才能使甲烷转化成C_2产物。     

Determination of stability constants of valinomycin complexes with ammonium and alkali metal ions by capillary affinity electrophoresis

Capillary affinity electrophoresis (CAE) has been employed to investigate quantitatively the interactions of valinomycin, macrocyclic depsipeptide antibiotic ionophore, with univalent cations, ammonium and alkali metal ions, K(+), Cs(+), Na(+), and Li(+), in methanol. The study involved measuring the change in effective electrophoretic mobility of valinomycin while the cation concentrations in the BGE were increased. The corresponding apparent stability (binding) constants of the valinomycin-univalent cation complexes were obtained from the dependence of valinomycin effective mobility on the cation concentration in BGE using a nonlinear regression analysis. The calculated apparent stability constants of the above-mentioned complexes show the substantially higher selectivity of valinomycin for K(+) and Cs(+) ions over Li(+), Na(+), and NH(4)(+) ions. CAE proved to be a suitable method for the investigation of both weak and strong interactions of valinomycin with small ions.     

IR spectra of complexes of Na,K and Cs with H2O in solid argon

One-to-one complexes between Na, K and Cs atoms and H₂O have been studied by using matrix IR spectroscopy. Perturbed water submolecule vibrations were observed in the bending and stretching regions for each complex. The perturbed stretching vibration is assigned to the totally symmetric stretching mode (v₁) of the H₂O submolecule in the complex based on isotopic shifts. In both regions, the shift is largest for the Li complex, and the shift decreases for the Na and K complexes but increases again for the Cs complex. The perturbed stretching mode is substantially intensified when compared to the perturbed bending mode. Intensification of the v₁ mode steadily increases down the alkali series and is explained by charge-transfer considerations.