Cyclic behavior of extruded magnesium: Experimental, microstructural and numerical approach

The present study aims at determining the influence of cyclic straining on the behavior of pure extruded magnesium. For this purpose, tensile, compressive and cyclic tests are performed (small plastic strains are applied (Δε^p/2 = 0.1% and 0.4%). Deformation mechanisms (slip and twin systems) have been observed by TEM and the different critical resolved shear stress (CRSS) have been determined. Based on microscopic observations, a crystal-plasticity-based constitutive model has been developed. The asymmetry between tensile and compressive loadings mainly results from the activation of hard slip systems in tension (such as 〈a〉 pyramidal and prismatic and 〈c + a〉 pyramidal glides) and twinning in compression. It is shown that basal slip is very easy to activate even for small Schmid factors. Numerical simulations reveal that untwinning in tension subsequent to compression must be considered to correctly fit the experimental S-shaped hysteresis curves. TEM observations indicate also intense secondary slips or twins inside the mother twins under cyclic conditions, so that twinning in compression and dislocation glide in tension are affected by cycling. The polycrystalline model allows to predict slip activities and twin volume fraction evolutions.     

Hardening evolution of AZ31B Mg sheet

The monotonic and cyclic mechanical behavior of O-temper AZ31B Mg sheet was measured in large-strain tension/compression and simple shear. Metallography, acoustic emission (AE), and texture measurements revealed twinning during in-plane compression and untwinning upon subsequent tension, producing asymmetric yield and hardening evolution. A working model of deformation mechanisms consistent with the results and with the literature was constructed on the basis of predominantly basal slip for initial tension, twinning for initial compression, and untwinning for tension following compression. The activation stress for twinning is larger than that for untwinning, presumably because of the need for nucleation. Increased accumulated hardening increases the twin nucleation stress, but has little effect on the untwinning stress. Multiple-cycle deformation tends to saturate, with larger strain cycles saturating more slowly. A novel analysis based on saturated cycling was used to estimate the relative magnitude of hardening effects related to twinning. For a 4% strain range, the obstacle strength of twins to slip is 3 MPa, approximately 1/3 the magnitude of textural hardening caused by twin formation (10 MPa). The difference in activation stress of twinning versus untwinning (11 MPa) is of the same magnitude as textural hardening.     

Incorporation of twinning into a crystal plasticity finite element model: Evolution of lattice strains and texture in Zircaloy-2

A crystal plasticity finite element code is developed to model lattice strains and texture evolution of HCP crystals. The code is implemented to model elastic and plastic deformation considering slip and twinning based plastic deformation. The model accounts for twinning reorientation and growth. Twinning, as well as slip, is considered to follow a rate dependent formulation. The results of the simulations are compared to previously published in situ neutron diffraction data. Experimental results of the evolution of the texture and lattice strains under uniaxial tension/compression loading along the rolling, transverse, and normal direction of a piece of rolled Zircaloy-2 are compared with model predictions. The rate dependent formulation introduced is capable of correctly capturing the influence of slip and twinning deformation on lattice strains as well as texture evolution.     

室温下镁合金板循环塑性随动强化本构模型研究

本文在具有各向异性屈服强度和拉压不对称的CPB06屈服准则的基础上,建立了基于随动强化的循环塑性本构模型．通过引入滑移、孪晶以及去孪等不同变形模式下的背应力演化方程,对室温下镁合金板材异常循环硬化行为进行了模拟．选取了AZ31B-O和AZ31B两种镁合金板材,通过拉伸-压缩-拉伸(T-C-T)和压缩-拉伸(C-T)等不同加载路径下的部分实验曲线确定模型的参数,采用三次插值多项式建立了背应力参数与上一变形模式中累积的等效塑性应变（即预应变）之间的函数关系．使用本模型对剩下的实验曲线进行了预测,发现预测结果与实验结果有良好的一致性,说明了当前模型的正确性．     

Numerical modeling of formability of extruded magnesium alloy tubes

In this paper, a constitutive framework based on a rate-dependent crystal plasticity theory is employed to simulate the large strain deformation phenomena in hexagonal closed-packed (HCP) metals such as magnesium. The new framework is incorporated into in-house codes. Simulations are performed using the new crystal plasticity model in which crystallographic slip and deformation twinning are the principal deformation mechanisms. Simulations of various stress states (uniaxial tension, uniaxial compression and the so-called ring hoop tension test) for the magnesium alloy AM30 are performed and the results are compared with experimental observations of specimens deformed at 200 °C. Numerical simulations of forming limit diagrams (FLDs) are also performed using the Marciniak–Kuczynski (M–K) approach. With this formulation, the effects of crystallographic slip and deformation twinning on the FLD can be assessed.     

Crystal plasticity analysis of texture development in magnesium alloy during extrusion

The texture development mechanism during the extrusion of magnesium alloy is investigated by experimental observation and numerical analysis. First, we perform a finite element analysis of a full extrusion process using a phenomenological constitutive equation, and it is confirmed that the loading condition of the extrusion process near the central axis of the billet is approximated by an equi-biaxial compression mode. Then, the equi-biaxial compression problem is adopted as a simplified boundary value problem to be solved using a crystal plasticity model to clarify the detailed texture development mechanism during the extrusion process. The crystal plasticity analysis of equi-biaxial compression successfully reproduces the texture development from an initial random texture to the final experimentally observed texture. The effects of the deformation modes (i.e. slip and twinning systems) implemented in the calculation and the reference stress ratio of basal to nonbasal slip systems on texture development are studied in detail. Finally, the mechanism of texture development during the extrusion process is discussed in terms of the lattice rotation caused by the activated slip systems.     

Relations between twin and slip in parent lattice due to kinematic compatibility at interfaces

The relationships between a slip system in the parent lattice and its transform by twinning shear are considered in regards to tangential continuity conditions on the plastic distortion rate at twin/parent interface. These conditions are required at coherent interfaces like twin boundaries, which can be assigned zero surface-dislocation content. For two adjacent crystals undergoing single slip, relations between plastic slip rates, slip directions and glide planes are accordingly deduced. The fulfillment of these conditions is investigated in hexagonal lattices at the onset of twinning in a single slip deforming parent crystal. It is found that combinations of slip system and twin variant verifying the tangential continuity of the plastic distortion rate always exist. In all cases, the Burgers vector belongs to the interface. Certain twin modes are only admissible when slip occurs along an 〈a〉 direction of the hexagonal lattice, and some others only with a 〈c + a〉 slip. These predictions are in agreement with EBSD orientation measurements in commercially pure Ti sheets after plane strain compression.     

Texture development and plastic anisotropy of B.C.C. strain hardening sheet metals

A Taylor-like polycrystal model is adopted here to investigate the plastic behavior of body centered cubic (b.c.c.) sheet metals under plane-strain compression and the subsequent in-plane biaxial stretching conditions. The <111> pencil glide system is chosen for the slip mechanism for b.c.c. sheet metals. The {110} <111> and {112} <111> slip systems are also considered. Plane-strain compression is used to simulate the cold rolling processes of a low-carbon steel sheet. Based on the polycrystal model, pole figures for the sheet metal after plane-strain compression are obtained and compared with the corresponding experimental results. Also, the simulated plane-strain stress—strain relations are compared with the corresponding experimental results. For the sheet metal subjected to the subsequent in-plane biaxial stretching and shear, plastic potential surfaces are determined at a given small amount of plastic work. With the assumption of the equivalence of the plastic potential and the yield function with normality flow, the yield surfaces based on the simulations for the sheet metal are compared with those based on several phenomenological planar anisotropic yield criteria. The effects of the slip system and the magnitude of plastic work on the shape and size of the yield surfaces are shown. The plastic anisotropy of the sheet metal is investigated in terms of the uniaxial yield stresses in different planar orientations and the corresponding values of the anisotropy parameter R, defined as the ratio of the width plastic strain rate to the through-thickness plastic strain rate under in-plane uniaxial tensile loading. The uniaxial yield stresses and the values of R at different planar orientations from the polycrystal model can be fitted well by a yield function recently proposed by Barlat et al. (1997b).     

An efficient constitutive model for room-temperature,low-rate plasticity of annealed Mg AZ31B sheet

Metals and alloys with hexagonal close packed (HCP) crystal structures can undergo twinning in addition to dislocation slip when loaded mechanically. The complexity of the plastic response and the limited extent of twinning are impediments to their room-temperature formability and thus their widespread adoption. In order to exploit the unusual deformation characteristics of twinning sheet materials in designing novel forming operations, a practical plane stress material model for finite element implementation was sought. Such a model, TWINLAW, has been constructed based on three phenomenological deformation modes for Mg AZ31B: S (slip), T (twinning), and U (untwinning). The modes correspond to three testing regimes: initial in-plane tension (from the annealed state), initial in-plane compression, and in-plane tension following compression, respectively. A von Mises yield surface with initial non-zero back stress was employed to account for plastic yielding asymmetry, with evolution according to a novel isotropic and nonlinear kinematic hardening model. Texture and its evolution were represented throughout deformation using a weighted discrete probability density function of c-axis orientations. The orientation of c-axes evolves with twinning or untwinning using explicit rules incorporated in the model.     

Continuum modeling of the response of a Mg alloy AZ31 rolled sheet during uniaxial deformation

Lightweight magnesium alloys, such as AZ31, constitute alternative materials of interest for many industrial sectors such as the transport industry. For instance, reducing vehicle weight and thus fuel consumption can actively benefit the global efforts of the current environmental industry policies. To this end, several research groups are focusing their experimental efforts on the development of advanced Mg alloys. However, comparatively little computational work has been oriented towards the simulation of the micromechanisms underlying the deformation of these metals. Among them, the model developed by Staroselsky and Anand [Staroselsky, A., Anand, L., 2003. A constitutive model for HCP materials deforming by slip and twinning: application to magnesium alloy AZ31B. International Journal of Plasticity 19 (10), 1843–1864] successfully captured some of the intrinsic features of deformation in Magnesium alloys. Nevertheless, some deformation micromechanisms, such as cross-hardening between slip and twin systems, have been either simplified or disregarded. In this work, we propose the development of a crystal plasticity continuum model aimed at fully describing the intrinsic deformation mechanisms between slip and twin systems. In order to calibrate and validate the proposed model, an experimental campaign consisting of a set of quasi-static compression tests at room temperature along the rolling and normal directions of a polycrystalline AZ31 rolled sheet, as well as an analysis of the crystallographic texture at different stages of deformation, has been carried out. The model is then exploited by investigating stress and strain fields, texture evolution, and slip and twin activities during deformation. The flexibility of the overall model is ultimately demonstrated by casting light on an experimental controversy on the role of the pyramidal slip 〈c + a〉 versus compression twinning in the late stage of polycrystalline deformation, and a failure criterion related to basal slip activity is proposed.     

Micromechanical quantification of elastic,twinning, and slip strain partitioning exhibited by polycrystalline,monoclinic nickel–titanium during large uniaxial deformations measured via in-situ neutron diffraction

We draw upon existing knowledge of twinning and slip mechanics to develop a diffraction analysis model that allows for empirical quantification of individual deformation mechanisms to the macroscopic behaviors of low symmetry and phase transforming crystalline solids. These methods are applied in studying elasticity, accommodation twinning, deformation twinning, and slip through neutron diffraction data of tensile and compressive deformations of monoclinic NiTi to ~18% true strain. A deeper understanding of tension–compression asymmetry in NiTi is gained by connecting crystallographic calculations of polycrystalline twinning strains with in situ diffraction measurements. Our analyses culminate in empirical, micromechanical quantification of individual elastic, accommodation twinning, deformation twinning, and slip contributions to the total macroscopic stress–strain response of a monoclinic material subjected to large deformations. From these results, we find that 20–40% of the total plastic response at high strains is due to deformation twinning and 60–80% due to slip.     

Study of lattice strains in magnesium alloy AZ31 based on a large strain elastic-viscoplastic self-consistent polycrystal model

The recently developed large strain elastic visco-plastic self-consistent (EVPSC) model, which incorporates both slip and twinning deformation mechanisms, is used to study the lattice strain evolution in extruded magnesium alloy AZ31 under uniaxial tension and compression. The results are compared against in-situ neutron diffraction measurements done on the same alloy. For the first time, the effects of stress relaxation and strain creep on lattice strain measurements in respectively displacement controlled and load controlled in-situ tests are numerically assessed. It is found that the stress relaxation has a significant effect on the lattice strain measurements. It is also observed that although the creep does not significantly affect the trend of the lattice strain evolution, a better agreement with the experiments is found if creep is included in the simulations.     

Integration of self-consistent polycrystal plasticity with dislocation density based hardening laws within an implicit finite element framework: Application to low-symmetry metals

We present an implementation of the viscoplastic self-consistent (VPSC) polycrystalline model in an implicit finite element (FE) framework, which accounts for a dislocation-based hardening law for multiple slip and twinning modes at the micro-scale grain level. The model is applied to simulate the macro-scale mechanical response of a highly anisotropic low-symmetry (orthorhombic) crystal structure. In this approach, a finite element integration point represents a polycrystalline material point and the meso-scale mechanical response is obtained by the mean-field VPSC homogenization scheme. We demonstrate the accuracy of the FE-VPSC model by analyzing the mechanical response and microstructure evolution of α-uranium samples under simple compression/tension and four-point bending tests. Predictions of the FE-VPSC simulations compare favorably with experimental measurements of geometrical changes and microstructure evolution. Specifically, the model captures accurately the tension–compression asymmetry of the material associated with twinning, as well as the rigidity of the material response along the hard-to-deform crystallographic orientations.     

The effect of time-dependent twinning on low temperature (<0.25 ∗ Tm) creep of an alpha-titanium alloy

The low-temperature (less than one-fourth of the melting temperature) creep deformation behavior of hexagonally close-packed (HCP) α-Ti–1.6 wt.% V was investigated. Creep tests were performed at various temperatures between room temperature and 205 °C at 95% of the respective yield stress at the different temperatures. The creep strain rate was found to increase with increasing temperature. Scanning and transmission electron microscopy revealed that slip and unusually slow twin growth, or time-dependent twinning, are active deformation mechanisms for the entire temperature range of this investigation. The activation energy for creep of this alloy was calculated to identify the rate-controlling deformation mechanism, and was found to increase with increasing creep strain. At low strain, the activation energy for creep was found to be close to the previously calculated activation energy for slip. At high strain, the calculated activation energy indicates that both slip and twinning are significant deformation mechanisms. The appearance of twinning at high strains is explained by a model for twin nucleation by dislocation pileups.     

On the strain hardening and texture evolution in high manganese steels: Experiments and numerical investigation

We present a systematic investigation on the strain hardening and texture evolution in high manganese steels where twinning induced plasticity (TWIP) plays a significant role for the materials' plastic deformation. Motivated by the stress–strain behavior of typical TWIP steels with compositions of Fe, Mn, and C, we develop a mechanistic model to explain the strain-hardening in crystals where deformation twinning dominates the plastic deformation. The classical single crystal plasticity model accounting for both dislocation slip and deformation twinning are then employed to simulate the plastic deformation in polycrystalline TWIP steels. While only deformation twinning is activated for plasticity, the simulations with samples composed of voronoi grains cannot fully capture the texture evolution of the TWIP steel. By including both twinning deformation and dislocation slip, the model is able to capture both the stress–strain behaviors and the texture evolution in Fe–Mn–C TWIP steel in different boundary-value problems. Further analysis on the strain contributions by both mechanisms suggests that deformation twinning plays the dominant role at the initial stage of plasticity in TWIP steels, and dislocation slip becomes increasingly important at large strains.     

An experimental study of cyclic deformation of extruded AZ61A magnesium alloy

Thin-walled tubular specimens were employed to study the cyclic deformation of extruded AZ61A magnesium alloy. Experiments were conducted under fully reversed strain-controlled tension-compression, torsion, and combined axial-torsion in ambient air. Mechanical twinning was found to significantly influence the inelastic deformation of the material. Cyclic hardening was observed at all the strain amplitudes under investigation. For tension-compression at strain amplitudes higher than 0.5%, the stress-strain hysteresis loop was asymmetric with a positive mean stress. This was associated with mechanical twinning in the compression phase and detwinning in the subsequent tension phase. Under cyclic torsion, the stress-strain hysteresis loops were symmetric although mechanical twinning was observed at high shear strain amplitudes. When the material was subjected to combined axial-torsion loading, the alternative occurrence of twinning and detwinning processes under axial stress resulted in asymmetric shear stress-shear strain hysteresis loops. Nonproportional hardening was not observed due to limited number of slip systems and the formation of mechanical twins. Microstructures after the stabilization of cyclic deformation were observed and the dominant mechanisms governing cyclic deformation were discussed. Existing cyclic plasticity models were discussed in light of their capabilities for modeling the observed cyclic deformation of the magnesium alloy.