基于光电振荡器的宽带射频下转换及在高清视频传输的应用

以无压缩全高清视频的光载无线传输为背景,通过研究宽带射频光子下转换技术,从而构建全高清视频的实时传输系统,其中下转换系统主要基于光电振荡器实现.由于光电振荡器的注入锁定,光微波信号中的载波信号被提取出来,并反馈至调制器,与宽带光微波信号混频,在光域实现信号下转换.实验论证了载频为10GHz,码率大于2Gb/s的信号下转换和有线无线传输.利用天线和光纤实现了距离为0.5m的无线分发和距离为10km的有线传输.本文还成功实现了1.5Gb/s无压缩高清视频信号的实时传输.实验结果表明,该系统具有大带宽、抗电磁干扰等优点,同时利用光电振荡器的自动相位跟踪技术,无须外加锁相等操作.整个下转换系统简单稳定,为高清视频的有线无线传输提供了论证和演示平台.     

基于注入半导体激光器的微波副载波相位调制信号产生

光载无线技术是解决终端超宽带无线通信的重要方法,光信号与微波/毫米波信号的融合处理技术在光-无线的数据格式转换中至关重要.提出了一种基于相位调制信号光注入Fabry-Perot型半导体激光器实现微波副载波相位调制信号产生的方法.光学注入半导体激光器的输出光场会产生一周期(P1)振荡效应, P1振荡产生的边带实现了相位调制信号光的调制分量的放大,被放大的调制分量与注入光载波在激光器腔内拍频形成微波副载波.注入光相位的变化导致新产生的微波副载波相位变化, 实现了注入信号光相位信息转化为微波副载波相位信息.本系统完成1.3 Gb/s, 2.7 Gb/s, 2 Gb/s光相位调制信号到微波副载波相位调制信号的转换,并测量了微波的单边带相位噪声. 通过光电转换和电域混频将还原出的光基带信号与原信号进行逻辑对比,证明了数据信息转换的正确性.     

用光电振荡器提取帧时钟实现4×10Gb/sOTDM信号165km传输

本文报道了一个以光电振荡器(OEO)为帧时钟提取装置的4×10Gb/s光时分复用通信实验系统.复用信号在165km SMF中传输的功率代价是0.47dB.     

光双二进制传输系统的性能研究

光双二进制信号的谱宽是传统二进制信号的一半,采用双二进制传输比二进制传输色散限制的中继距离可增加一倍.本文对采用传统光接收机的光双二进制传输系统用MATLAB进行了通信仿真.结果表明:在完全消光条件下,10 Gb/s双二进制信号在常规单模光纤上传输可达160 km,40 Gb/s双二进制信号在非零色散光纤上为30 km,均比二进制增加了一倍;详细考察了消光比对传输的影响,只有消光比大于25 dB时,双二进制相对于二进制传输的优越性才呈现出来.     

自启动的非归零/归零码和光电时钟信号发生器及码型转换

采用双波长注入一包含伪随机码发生器与相位调制器的光电振荡器可以同时得到非归零(NRZ)码,归零(RZ)码以及光,电时钟信号输出。该方案使用了光域耦合的双环路结构,在不增加有源器件的条件下实现边模抑制。相位调制器用于反馈调制并同时实现占空比可调的非归零码到归零码的转换。双波长的注入排除了编码信号在振荡器中引入的非时钟频率成分。实验给出了10 Gb/s工作速率下的结果,得到了抖动为637 fs的光信号输出。转换得到的归零码信号占空比约为33%。输出电时钟信号的相位噪声在频偏10 kHz处为-109 dBc/Hz,边模抑制比为58 dB。     

基于半导体光放大器四波混频效应的多种调制格式的波长转换实验

实验报道了利用半导体光放大器(SOA)的四波混频(FWM)效应实现多种码型的波长转换.其中对于非归零(NRZ)信号实现了从单信道到三信道的多波长转换.调制速率从10 Gb/s到40 Gb/s均实现多波长转换.对于归零(RZ)信号分别实现了20 Gb/s和40 Gb/s的RZ格式的波长转换和40 Gb/s的载波抑制归零(CSRZ)格式的波长转换,利用光纤布拉格光栅(FBG)作为带陷滤波器消除共轭光和抽运光之间的串扰.对于非归零差分相移键控(NRZ_DPSK)信号分别实现了20 Gb/s和40 Gb/s的波长转换,利用实验室自制的光纤延时干涉仪进行NRZ-DPSK信号的解调.基于FWM效应的转换光的输出消光比大于7 dB,转换后消光比退化约为3 dB.     

基于交替起振光电振荡器的大量程高精度绝对距离测量技术

提出了一种基于交替起振的光电振荡器的大量程、高精度绝对距离测量方法.此方法构建了两个光电振荡环路,分别为测量环和参考环.通过切换光开关实现测量/参考光电振荡器的交替起振;通过切换微波开关实现光电振荡器高阶/低阶振荡模式的转换;通过频率计依次记录测量/参考光电振荡器的高阶/低阶振荡频率,然后计算测量/参考光电振荡器的腔长进一步得到绝对距离.本方案的优点是:由于采用了测量/参考两个光电振荡器腔长相减的方法消除系统自身的漂移,不需要控制腔长,结构简单.实验中,利用公里量级的光纤来模拟大量程的待测距离,利用高步进精度的光延时线来模拟距离变化.在等效6 km的空间往返待测距离上,测量误差为3.5μm,相对测量精度达到5.8×10~(–10).     

0.14 THz超高速无线通信系统实验研究

 介绍了0.14 THz超高速无线通信实验系统的主要组成部分和主要实验结果。从太赫兹电子学出发,基于太赫兹半导体器件和宽带数字调制解调技术,采用一种“低频段高速矢量调制＋谐波混频＋放大”的太赫兹高速信息传输技术路线,在国内首次成功实现了0.14 THz 0.5 km 10 Gb/s高速信号实时传输和软件化事后解调,同时进行了4路高清视频信号的传输与解调。     

基于光电反馈环单元时钟提取与解复用的160Gb/s OTDM信号100km传输

提出了一种能够同时对高速光时分复用技术信号解复用与时钟提取的光电反馈环单元.在接收端,采用光电反馈环单元,信号单次通过即可同时完成160Gb/s到10Gb/s的解复用与时钟提取:两级电吸收调制器级联工作方式缩减了采样窗口宽度,满足了解复用小于6.25ps超窄采样窗口的要求;而闭合环路的锁相同步工作方式,使所提取的时钟信号抖动(JitterRMS)由2.4ps降至450fs.基于该结构,实验上成功实现了无误码的100km160Gb/s光时分复用技术传输及传输后无误码地解复用与时钟提取,功率代价小于3dB.     

基于光电反馈环单元时钟提取与解复用的160 Gb/s OTDM 信号100 km传输

提出了一种能够同时对高速光时分复用技术信号解复用与时钟提取的光电反馈环单元.在接收端,采用光电反馈环单元,信号单次通过即可同时完成160 Gb/s到10 Gb/s的解复用与时钟提取：两级电吸收调制器级联工作方式缩减了采样窗口宽度,满足了解复用小于6.25 ps超窄采样窗口的要求|而闭合环路的锁相同步工作方式,使所提取的时钟信号抖动（Jitter RMS）由2.4 ps降至450 fs.基于该结构,实验上成功实现了无误码的100 km 160 Gb/s光时分复用技术传输及传输后无误码地解复用与时钟提取,功率代价小于3 dB.     

Characterization of ROF signal based on cascaded optical carrier suppression modulation technique

The paper experimentally demonstrated the optical frequency quadrupling microwave signal generation, a 4 GHz radio frequency (RF) signals up-conversion to 16 GHz in a radio over fiber (ROF) link, using twice optical carrier suppression modulation. The RF signal was mixed with 1.25 Gbps NRZ-OOK data firstly and then modulated by two cascaded single-electrode optical intensity modulators. The obtained 1.25 Gbps/16 GHz ROF signal was transmitted and characterized in the optical fiber link. At BER of 10^?9, low power penalty of 1.0 and 1.4 dB were obtained over a fiber link with a transmission distance of 25 and 50 km.     

Multi-functional fibre-optic microwave links

The multi-functionality of microwave links based on remote heterodyne detection of signals from a dual-frequency laser transmitter is discussed and experimentally demonstrated in this paper. Typically, direct detection in conjunction with optical intensity modulation is used to implement fibre-optic microwave links. The resulting links are inherently transparent and mainly used for signal transmission. As opposed to direct detection links, remote heterodyne detection links can directly perform functionalities such as modulation, frequency conversion, and transparent signal recovery in addition to signal transmission. All three functionalities are presented and experimentally demonstrated with a remote heterodyne detection link based on a dual-frequency laser transmitter with two offset phase locked semiconductor lasers. In the modulating link a 1Gbit/s baseband signal is QPSK modulated onto a 9GHz RF carrier. The frequency converting link demonstrates up-conversion of a 100Mbit/s PSK signal from a 2GHz carrier to a 9GHz carrier with penalty-free transmission over 25km of optical fibre. Finally, the transparent signal recovering link transmits a standard FM video 7.6GHz radio-link signal over 25km of optical fibre without measurable distortion.     

无压缩多路数字视频光纤传输系统的研制

提出了一种无压缩多路数字视频光纤传输系统,该系统基于时分复用技术采用比特串行数字视频传输方式实现在一根光纤中传输多路视频信号. 介绍了系统设计思想、关键技术及高速数据接口设计,并通过实验证明该系统工作稳定、实时传输效果好、是远程视频监控系统及安防系统的实用方案.     

一种基于串联谐振腔的高性能光电振荡器

提出了一种利用串联谐振腔来抑制光电振荡器边模的方案. 此方案中, 在传统光电振荡器结构中加入无源微波谐振腔结构来提高滤波器的Q值. 分析了该结构的基本原理, 并与传统光电振荡器结构进行对比, 此结构能有效提高边模抑制比. 实验中产生了10 GHz的微波信号, 所测得的边模抑制比达72 dB, 单边带相位噪声为-122 dBc/Hz@10 kHz. 同时, 利用锁相技术, 振荡频率的稳定性得到了很大的改善, 在3 h内漂移小于± 4 Hz. 该方案无需增加有源器件, 保留了传统光电振荡器低相位噪声的优势, 又有效抑制了边模, 为光电振荡器的应用提供了一种新的方法.     

Photonic vector signal generation employing a novel optical direct-detection in-phase/quadrature-phase upconversion

This work demonstrates the feasibility of the generation of an RF direct-detection vector signal using optical in-phase/quadrature-phase (I/Q) upconversion. The advantage of the proposed transmitter is that no electrical mixer is needed to generate the RF signal. Therefore, I/Q data of RF signals are processed at baseband at the transmitter, which is independent of the carrier frequency of the generated RF signal. A 10 Gb/s 16 quadrature amplitude modulation signal is experimentally demonstrated. Following transmission over a 50 km single-mode fiber, the power penalty is negligible. Moreover, I/Q imbalance of the proposed transmitter is studied and compensated by digital signal processing, which is both numerically and experimentally verified.     

光子型远程分布式微波信号接收码元速率估计

基于光子学技术,设计了一种针对远程分布式微波信号接收的码元速率估计方案。首先,远程终端将接收的微波信号经电光调制器对连续激光源进行载波抑制双边带调制,生成携带微波信号的两个光边带信号;此光信号经光纤链路传输至中心站在光域滤除其中一个边带;其次,进行光电探测,通过分析电频谱的谐波实现微波信号码元速率估计。针对此方案,搭建仿真及实验系统装置:仿真成功地从60 GHz微波信号中提取出0.8 GBaud和6 GBaud的二进制伪随机码(PRBS)信号码元速率、从25 GHz微波信号中提取出3GBaud的PRBS码元速率;实验成功地从25 GHz的微波信号中提取出3 GBaud和5 GBaud的PRBS码元速率。     

Optoelectronic oscillator using a LiNbO3 phase modulator for self-oscillating frequency comb generation

Optical frequency comb generation by using a novel optoelectronic oscillator (OEO) is proposed and demonstrated with the emphasis placed on self-oscillating operation. In the OEO, a wideband LiNbO3 phase modulator is driven with a large-amplitude radio-frequency (RF) feedback signal to generate a deeply phase-modulated light wave; accordingly, an optical frequency comb with a bandwidth greater than the RF signal is generated by self-oscillation. Although it generates multifrequency components, the OEO exhibits characteristics of a single-mode oscillator. Its operation is stable and self-starting. An optical frequency comb with a 120 GHz bandwidth and 9.95 GHz frequency spacing was successfully generated by self-oscillation at a single frequency.     

电光调制在被动综合孔径成像探测中的应用

介绍了一种新型被动综合孔径成像探测方法:视场辐射信号被接收和放大后,通过电光幅度调制将其幅度和相位信息加载到光波上,经光纤传输在末端形成阵列,通过光学系统直接成像,将视场实时恢复出来.该方法可实现工作在微波、毫米波和太赫兹波段的高分辨力实时成像探测的目的.深入分析了电光调制器在综合孔径成像探测中的应用,建立电光调制模型,讨论了在小信号调制下的电光幅度调制近似理论.通过数值计算与仿真分析,得到综合孔径成像探测中电光调制器的调制信号强度限制的有关结论.结果表明,利用上变频电光调制技术和光信息处理,所得到的成像仿真图的半峰全宽和信噪比性能都优于传统的基于下变频技术的成像仿真结果.     

Full-duplex radio-over-fiber system based on a modified single-side band modulation

A full-duplex radio-over-fiber system based on a modified single-sideband using external modulator is proposed and demonstrated. At the central station, a CW lightwave is intensity-modulated by a RF signal to generate a DSB signal. After the central carrier and the two first-order sidebands are separated by a FBG, the central carrier is modulated with a baseband data at 2.5 Gbit/s. Then, it is recombined with the un-modulated first-order sidebands to generate optical millimeter-wave by an optical coupler with a certain coupling coefficient and transmitted to the base station over single-mode fiber. The central carrier and one of the first-order sidebands are beaten to generate the mm-wave when they are detected by an optical receiver. Another first sideband is reused as carrier for uplink connection. The dispersion performance of the generated mm-wave is theoretically analyzed; one can see that the effect of dispersion and requirement of the optical power are reduced. The PIN-PD can avoid working in a high-DC saturation range which may distort the RF components and depress the responsibility of the detector. The stimulant results show that the system can reduce the effect of dispersion effectively, and immune the fading effect and the walking-off signals. It is suitable for a long distance transmission.