MgCl2/Et3N催化合成α,β-不饱和氰代酯

用MgCl₂/Et₃N催化氰乙酸乙酯和芳香醛的缩合反应合成α,β-不饱和氰代酯, 反应可在室温进行. 产率87%～92%.     

3D α-Fe2O3/掺氮石墨烯/碳纳米管复合材料及其储锂性能

针对α-Fe₂O₃负极在充放电过程中存在的体积膨胀及首次库伦效率低等主要问题,本文采用简单的水热法制备出具有三维多孔结构的α-Fe₂O₃/掺氮石墨烯(N-GNS)/碳纳米管(CNTs)复合材料。XRD,SEM,TEM及XPS等测试结果表明碳纳米管成功插入到掺氮石墨烯片层间,暴露N-GNS表面的晶格缺陷,为α-Fe₂O₃晶体生长提供了大量成核位点。粒径大小为30~70nm的α-Fe₂O₃颗粒均匀锚定于N-GNS/CNTs三维复合碳载体内进行高效储锂反应。电化学测试结果显示,这种三维复合结构有效改善了α-Fe₂O₃/GNS负极的电化学性能。     

锂离子电池正极材料LiNi0.75-xCoxMn0.25O2的合成及电化学性能研究

以LiOH·H₂O、Ni(OAc)₂·4H₂O、Co(OAc)₂·4H₂O和MnO₂为原料，在水热反应釜中预处理，然后进行高温固相反应，合成了一系列锂镍钴锰氧化物LiNi_0.75-xCo_xMn_0.25O₂(x=0.05,0.10,0.15,0.20,0.25)。通过X射线衍射(XRD)、扫描电子显微镜（SEM）和电化学性能测试对所得样品的结构、形貌、粒径及电化学性能进行了表征。结果表明，当x=0.20时，所合成的正极材料具有很好的α-NaFeO₂型层状晶体结构，晶胞参数a=0.286 1 nm，c=1.416 4 nm， V=0.100 4 nm³，以50 mA·g^-1的电流密度在3～4.3 V(vs Li/Li⁺)充放电时，首次放电比容量达172.5 mAh·g^-1，首次放电效率高达90.9%，30个循环后其放电比容量依然保持在161.1 mAh·g^-1。     

纳米钙钛矿LaxSr1-xFe1-yCoyO3复合氧化物的制备和表征

用甘氨酸-硝酸盐燃烧合成法，制备La_xSr_1-xFe_1-yCo_yO₃复合氧化物的陶瓷粉末，对该钙钛矿型氧化物进行了XRD、IR、紫外漫反射光谱及循环伏安曲线分析。结果表明：该复合氧化物粉体平均晶粒为15.3～29.8 nm,为立方和正交晶系。该氧电极具有双功能催化特性，但不完全可逆。对水溶液染料进行光解实验，利用紫外-可见、人工神经网络光度法研究La_xSr_1-xFe_1-yCo_yO₃的催化性能。结果表明：CO²⁺的加入可使La_xSr_1-xFeO₃的光催化活性有所提高，B位离子(Fe³⁺，CO²⁺)改变与加入，使La_xSr_1-xFe_1-yCo_yO₃(x=0.7，0.3；y=0.3，0.9，1)光催化活性高于La_xSr_1-xFeO₃。同时，对5种染料进行紫外光解，在0.75 h，脱色率大于91%，并为动力学一级反应。     

KF/Al2O3催化下4-芳基-9,10-二氢萘并[2,1-b]-4H-吡喃衍生物的合成

在KF/Al₂O₃催化下, α,β-不饱和腈或α,β-不饱和羧酸酯和7-甲氧基-1,2,3,4-四氢-2-萘酮反应, 生成了一系列4-芳基-9,10-二氢萘并[2,1-b]-4H-吡喃衍生物. 产物的结构通过红外光谱和核磁共振氢谱进行表征, 并通过X单晶衍射分析进一步证实产物的结构.     

La1-xSrxCoO3（x=0，0.2，0.4，0.6，0.8）钙钛矿型氧化物的催化性能及改性

通过溶胶-凝胶法制备出A位Sr掺杂的钙钛矿型氧化物La_1-xSr_xCoO₃（x=0,0.2,0.4,0.6,0.8）,并将其作为催化剂应用于双功能氧电极中。测试结果表明,A位Sr的掺杂的La_1-xSr_xCoO₃比LaCoO₃具有更高的电催化活性,并且La_0.6Sr_0.4CoO₃在氧还原和氧析出反应中均表现出最优的催化性能,最大电流密度分别达到0.244 A·cm^-2（-0.6 V vs Hg/HgO）和0.303 A·cm^-2（1 V vs Hg/HgO）。为进一步提高催化剂的催化活性,将水热法制备的α-MnO₂纳米管与La_0.6Sr_0.4CoO₃复合作为双功能催化剂。当α-MnO₂的质量分数为40%时,比起单一的α-MnO₂或钙钛矿氧化物,α-MnO₂/La_0.6Sr_0.4CoO₃复合材料表现出协同效应,有更好的双功能电催化活性,使双效氧电极具有更好的电化学性能及稳定性。     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

层状O2结构锂锰氧化物Li0.60[MgxCoyMn1-x-y]O2的制备及结构表征

本文采用离子交换法分别制备了双复合锂锰氧化物Li_0.60[Mg_xMn_1-x]O₂(0.05 ≤ x ≤ 0.15)和三复合锂锰氧化物Li_0.60[Mg_xCo_yMn_1-x-y]O₂(x=0.05，0.05 ≤      

水在C12-EOx-C12•2Br/正己醇/正庚烷W/O微乳中的状态

以FT-IR方法研究了水/C₁₂-EO_x-C₁₂•2Br/正己醇/正庚烷形成的W/O微乳中水的状态. 结果表明, 其中的水存在4种状态, 分别为阳离子头基结合水、反离子结合水、类似本体的水以及束缚在微乳栅栏层中的水. 由解卷积技术分解FT-IR谱图, 进而获得每个表面活性剂分子对应于这4种状态水分子的数目n_N＋, n_Br-, n_b和n_f. 随着水含量(W₀)增加, n_b急剧增大, n_N＋少许上升, 而n_f和n_Br-维持不变, 这说明微乳水核逐渐长大, 且在所考察W₀范围内, 表面活性剂头基解离度保持不变.     

钙钛矿型LaxSr1－xNi1－yCoyO3光电催化活性研究

用甘氨酸-硝酸盐燃烧合成法, 制备La_xSr_1－xNi_1－yCo_yO₃复合氧化物的陶瓷粉末, 对钙钛矿氧化物进行了XRD结构分析. 在通氧或不通氧下测试氧还原和氧析出的循环伏安曲线. 结果表明: 该氧电极具有双功能催化特性, 但不完全可逆. 利用汞灯作为激发光源, 进行几种水溶性染料和五种混合染料光解实验, 利用紫外-可见、红外以及人工神经网络光度法研究La_xSr_1－xNi_1－yCo_yO₃的催化性能. 结果表明: La_xSr_1－xNi_1－yCo_yO₃ (x＝0.7, 0.9, 1; y＝0.3, 0.75)复合氧化物都具有较强光催化特性; La_xSr_1－xNi_1－yCo_yO₃的光催化活性高于La_xSr_1－xNiO₃, 这与B位离子(Ni^2—, Co^2－)的电子构型有关; Co^2＋的加入可使La_xSr_1－xNiO₃的光催化活性有所提高.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Separation of Tl/III/ from Tl/I/

A method for the separation of Tl/III/from Tl/I/ is reported employing 1-/2-pyridylazo/-2-naphthol /PAN/ and Rhodamine-B as extracting agents.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.     

Analysis of nonvalent interactions in the crystals of conformational polymorphs of the composition CaHbNcOdSe by means of molecular voronoi-dirichlet polyhedra

Nonvalent interactions in crystals of compounds of the composition C _a H _b N _c O _d S _e that exhibit conformational polymorphism and have no fewer than four structurally characterized modifications are analyzed using molecular Voronoi-Dirichlet polyhedrals. A unique combination of the types of occurring intra- and intermolecular nonvalent contacts is shown to correspond to each conformational polymorph. Nonvalent interactions involving hydrogen atoms are found to occur most often in crystal structures, and least often those involving S, N, and O atoms.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

橙红色荧光粉Ca_(1-x-y)Sm_xBi_ySiO_3的制备及其发光性能

以Sm3+作为激活剂,Bi3+作为辅助激活剂,采用水热法合成Ca1-x-ySmxBiySi O3前驱体,然后在1 100℃焙烧得到系列橙红色荧光粉。用X-射线衍射仪、扫描电镜和荧光分光光度计和傅里叶变换红外光谱等手段对样品的组成、结构和形貌及其发光性质进行分析和表征。分析结果表明:产物都为三斜晶系结构的Ca1-x-ySmxBiySi O3和四方结构的方石英Si O2共熔体。在405 nm近紫外光激发下,产物的发射光谱由3个峰组成,发射峰值位于566、606和650 nm处,分别归属于Sm3+的4G5/2→6HJ/2(J=5,7,9)跃迁。产物的激发光谱在405 nm有很强的发射带,与近紫外LED芯片匹配。随着Sm3+掺量的增加,样品发光强度先增强后减弱,当Sm3+的物质的量分数为3%时发光强度达到最大,浓度猝灭机理为电偶极-电偶极相互作用。当Bi3+的物质的量分数在0.3%~1.5%时,对产物Ca0.97Sm0.03Si O3的荧光强度起敏化作用。Sm3+和Bi3+的最佳物质的量分数分别为3%和0.5%。     

Zr1-xMxWMoO8-x/2和Zr1-xMxW2O8-x/2固溶体的晶胞参数与晶格畸变的关系

合成了Zr1-xMxWMoO8-x/2(M=Er,Tm,Yb,Sc,In,Ga,Al)和Zr1-xMxW2O8-x/2(M=Eu,Er,Yb,Sc,In,Ga,Al)2个系列的固溶体,前者具有β-ZrW2O8结构类型(简称β相);后者具有α-ZrW2O8结构类型(简称α相)。建立了相和相的晶胞参数与M3+离子浓度的Vegard方程,测定了上述固溶体的固溶度。讨论了M3+离子的化学性质与Vegard斜率SV的关系。分析了α相的SαA与β相的SβA的关系;揭示了α-Zr1-xMxW2O8-x/2晶格中2[WO4]四面体对的取向有序程度对晶格畸变的贡献。提出上述固溶体的晶胞参数随溶质浓度增加而减小,主要是由于氧空位缺陷相互作用的结果。