Direct As,Bi, Ge,Hg and Se(IV) cold vapor/hydride generation from coal fly ash slurry samples and determination by electrothermal atomic absorption spectrometry

Direct cold vapor and hydride generation procedures for As, Bi, Ge, Hg and Se(IV) from aqueous slurry of coal fly ash samples have been developed by using a batch mode generation system. Ir-treated graphite tubes have been used as a preconcentration and atomization medium of the vapors generated. A Plackett–Burman experimental design has been used as a strategy for evaluation of the effects of several parameters affecting the vapor generation efficiency from solid particles, vapor trapping and atomization efficiency from Ir-treated graphite tubes. The effects of parameters such as hydrochloric acid and sodium tetrahydroborate, argon flow rate, trapping and atomization temperatures, trapping time, acid solution volume and mean particle size have been investigated. The significant parameters obtained (trapping and atomization temperatures for As and Ge; trapping temperature and trapping time for Bi; argon flow rate and atomization temperature for Se) have been optimized by 2²+star central composite design. For Hg, the trapping temperature has been also significant. Optimum values of the parameters have been selected for the development of direct cold vapor/hydride generation methods from slurry particles. The accuracy of methods have been verified by using NIST-1633a coal fly ash certified reference material. Absolute detection limits of 11.5, 48.0, 600, 55.0 and 11.0 ng l⁻¹ for As, Bi, Ge, Hg and Se have been achieved, respectively. A particle size less than 50 μm has shown to be adequate to obtain total cold vapor/hydride generation of metals content in the aqueous slurry particles.     

Determination of mercury by electrochemical cold vapor generation atomic fluorescence spectrometry using polyaniline modified graphite electrode as cathode

An electrochemical cold vapor generation system with polyaniline modified graphite electrode as cathode material was developed for Hg (II) determination by coupling with atomic fluorescence spectrometry. This electrochemical cold vapor generation system with polyaniline/graphite electrode exhibited higher sensitivity; excellent stability and lower memory effect compared with graphite electrode electrochemical cold vapor generation system. The relative standard deviation was 2.7% for eleven consecutive measurements of 2 ng mL^− 1 Hg (II) standard solution and the mercury limit of detection for the sample blank solution was 1.3 рg mL^− 1 (3σ). The accuracy of the method was evaluated through analysis of the reference materials GBW09101 (Human hair) and GBW 08517 (Laminaria Japonica Aresch) and the proposed method was successfully applied to the analysis of human hairs.     

Evaluation of a new electrolytic cold vapor generation system for mercury determination by AFS

In this study we firstly report a new electrolytic cold vapor generation system for mercury determination on Pt/Ti cathode in the presence of organic acid catholyte. Comparing with the traditional inorganic acid, formic acid increased the signal intensity of Hg vapor from electrolytic generation on Pt cathode and reduced the impact of cathode erosion on the stability of signal intensity. Moreover, formic acid has better interference tolerance. The introduction location for carrier gas is probably the most important factor that influences the signal intensity of Hg from electrolytic vapor generation. The effects of the electrolytic conditions and interference ions on the ECVG have been studied. Under the optimized conditions, the detection limit (3σ) of Hg (II) in aqueous solutions is 1.4 ng L⁻¹; a relative standard deviation of 2.3% for 1 μg L⁻¹ Hg was obtained. The accuracy of this method was verified by the determination of mercury in the certified reference materials. This system has been applied satisfactorily to the determination of Hg in Traditional Chinese Medicines samples.     

Organic,inorganic and total mercury determination in fish by chemical vapor generation with collection on a gold gauze and electrothermal atomic absorption spectrometry

A method for organic, inorganic and total mercury determination in fish tissue has been developed using chemical vapor generation and collection of mercury vapor on a gold gauze inside a graphite tube and further atomization by electrothermal atomic absorption spectrometry. After drying and cryogenic grinding, potassium bromide and hydrochloric acid solution (1 mol L^− 1 KBr in 6 mol L^− 1 HCl) was added to the samples. After centrifugation, total mercury was determined in the supernatant. Organomercury compounds were selectively extracted from KBr solution using chloroform and the resultant solution was back extracted with 1% m/v L-cysteine. This solution was used for organic Hg determination. Inorganic Hg remaining in KBr solution was directly determined by chemical vapor generation electrothermal atomic absorption spectrometry. Mercury vapor generation from extracts was performed using 1 mol L^− 1 HCl and 2.5% m/v NaBH₄ solutions and a batch chemical vapor generation system. Mercury vapor was collected on the gold gauze heated resistively at 80 °C and the atomization temperature was set at 650 °C. The selectivity of extraction was evaluated using liquid chromatography coupled to chemical vapor generation and determination by inductively coupled plasma mass spectrometry. The proposed method was applied for mercury analysis in shark, croaker and tuna fish tissues. Certified reference materials were used to check accuracy and the agreement was better than 95%. The characteristic mass was 60 pg and method limits of detection were 5, 1 and 1 ng g^− 1 for organic, inorganic and total mercury, respectively. With the proposed method it was possible to analyze up to 2, 2 and 6 samples per hour for organic, inorganic and total Hg determination, respectively.     

Determination of thiomersal by flow injection coupled with microwave-assisted photochemical online oxidative decomposition of organic mercury and cold vapor atomic fluorescence spectroscopy

We developed a flow injection (FI) method for the determination of thiomersal (sodium ethylmercurithiosalicylate, C₉H₉HgNaO₂S) based on the UV/microwave (MW) photochemical, online oxidation of organic mercury, followed by cold vapor generation atomic fluorescence spectrometry (CVG-AFS) detection. Thiomersal was quantitatively converted in the MW/UV process to Hg(II), with a yield of 97 ± 3%. This reaction was followed by the reduction of Hg(II) to Hg(0) performed in a knotted reaction coil with NaBH₄ solution, and AFS detection in an Ar/H₂ miniaturized flame. The method was linear in the 0.01–2 μg mL⁻¹ range, with a LOD of 0.003 μg mL⁻¹. This method has been applied to the determination of thiomersal in ophthalmic solutions, with recoveries ranging between 97% and 101%. We found a mercury concentration in commercial ophthalmic solutions ranging between 7.5 and 59.0 μg mL⁻¹.     

A new vapor generation system for mercury species based on the UV irradiation of mercaptoethanol used in the determination of total and methyl mercury in environmental and biological samples by atomic fluorescence spectrometry

A new vapor generation system for mercury (Hg) species based on the irradiation of mercaptoethanol (ME) with UV was developed to provide an effective sample introduction unit for atomic fluorescence spectrometry (AFS). Preliminary investigations of the mechanism of this novel vapor generation system were based on GC–MS and FT–IR studies. Under optimum conditions, the limits of determination for inorganic divalence mercury and methyl mercury were 60 and 50 pg mL⁻¹, respectively. Certified reference materials (BCR 463 tuna fish and BCR 580 estuarine sediment) were used to validate this new method, and the results agreed well with certified values. This new system provides an attractive alternative method of chemical vapor generation (CVG) of mercury species compared to other developed CVG systems (for example, the traditional KBH₄/NaOH–acid system). To our knowledge, this is the first systematic report on UV/ME-based Hg species vapor generation and the determination of total and methyl Hg in environmental and biological samples using UV/ME–AFS. Figure A new vapor generation system for mercury species using mercaptoethanol under UV irradiation was developed as an effective sample introduction unit for atomic fluorescence spectrometry     

Photo-induced cold vapor generation with low molecular weight alcohol, aldehyde, or carboxylic acid for atomic fluorescence spectrometric determination of mercury

With UV irradiation, Hg²⁺ in aqueous solution can be converted into Hg⁰ cold vapor by low molecular weight alcohols, aldehydes, or carboxylic acids, e.g., methanol, formaldehyde, acetaldehyde, glycol, 1,2-propanediol, glycerol, acetic acid, oxalic acid, or malonic acid. It was found that the presence of nano-TiO₂ more or less improved the efficiency of the photo-induced chemical/cold vapor generation (photo-CVG) with most of the organic reductants. The nano-TiO₂-enhanced photo-CVG systems can be coupled to various analytical atomic spectrometric techniques for the determination of ultratrace mercury. In this work, we evaluated the application of this method to the atomic fluorescence spectrometric (AFS) determination of mercury in cold vapor mode. Under the optimized experimental conditions, the instrumental limits of detection (based on three times the standard deviation of 11 measurements of a blank solution) were around 0.02–0.04 μg L⁻¹, with linear dynamic ranges up to 15 μg L⁻¹. The interference of transition metals and the mechanism of the photo-CVG are briefly discussed. Real sample analysis using the photo-CVG-AFS method revealed that it was promising for water and geological analysis of ultralow levels of mercury. Image of the photo-CVG instrumentation showing the photoreactor inside the water cooling unit     

An Independent 1D Single‐Walled Metal–Organic Nanotube Transformed from a 2D Layer Exhibits Highly Selective and Reversible Sensing of Nitroaromatic Compounds

The syntheses and structures of two new Zn^II complexes, a 2D graphite‐like layer {[Zn(PIA)H₂O] ? H₂O}_n ( 1 ) and an independent 1D single‐walled metal–organic nanotube (SWMONT) {[Zn₂(PIA)₂(bpy)₂] ? 2.5 H₂O ? DMA}_n ( 2 ), have been reported based on a “Y”‐shaped 5‐(pyridine‐4‐yl)isophthalic acid ligand (H₂PIA). Interestingly, the 2D graphite‐like layer in 1 can transform into the independent 1D SWMONT in 2 with addition of 2,2′‐bipyridine (bpy), which represents the first successfully experimental example of an independent 1D metal–organic nanotube generated from a 2D layer by a “rolling‐up” mechanism.     

Continuous flow electrolytic cold vapor generation atomic fluorescence spectrometric determination of Hg in water samples

The determination of trace concentrations of Hg in water samples by the use of electrolytic cold vapor generation (ECVG) system and AFS was studied. Several buffer solutions were used and the detection limits with these systems were found to be by a factor of 1–2 lower than in the conventional electrolytic cold vapor generation system. Comparing with the traditional inorganic acid, phosphate buffer solution (PBS) increased the signal intensity of Hg vapor from electrolytic generation on Pt cathode and reduced the impact of cathode erosion on the stability of signal intensity. Moreover, buffer solution has better interference tolerance. The effects of the electrolytic conditions and interference ions on the ECVG have been studied. Under optimized conditions and with PBS as catholyte the detection limit for Hg was found to be 0.27 ng L⁻¹. The relative standard deviation was 2.8% for 11 consecutive measurements of 1 μg L⁻¹ Hg. This method has been applied in the determination of inorganic Hg in Yangtze River water.     

A double-stage tube furnace—acid-trapping protocol for the pre-concentration of mercury from solid samples for isotopic analysis

High-precision mercury (Hg) stable isotopic analysis requires relatively large amounts of Hg (>10 ng). Consequently, the extraction of Hg from natural samples with low Hg concentrations (<1–20 ng/g) by wet chemistry is challenging. Combustion–trapping techniques have been shown to be an appropriate alternative [1]. Here, we detail a modified off-line Hg pre-concentration protocol that is based on combustion and trapping. Hg in solid samples is thermally reduced and volatilized in a pure O₂ stream using a temperature-programmed combustion furnace. A second furnace, kept at 1,000 °C, decomposes combustion products into H₂O, CO₂, SO₂, etc. The O₂ carrier gas, including combustion products and elemental Hg, is then purged into a 40 % (v/v) acid-trapping solution. The method was optimized by assessing the variations of Hg pre-concentration efficiency and Hg isotopic compositions as a function of acid ratio, gas flow rate, and temperature ramp rate for two certified reference materials of bituminous coals. Acid ratios of 2HNO₃/1HCl (v/v), 25 mL/min O₂ flow rate, and a dynamic temperature ramp rate (15 °C/min for 25–150 and 600–900 °C; 2.5 °C/min for 150–600 °C) were found to give optimal results. Hg step-release experiments indicated that significant Hg isotopic fractionation occurred during sample combustion. However, no systematic dependence of Hg isotopic compositions on Hg recovery (81–102 %) was observed. The tested 340 samples including coal, coal-associated rocks, fly ash, bottom ash, peat, and black shale sediments with Hg concentrations varying from <5 ng/g to 10 μg/g showed that most Hg recoveries were within the acceptable range of 80–120 %. This protocol has the advantages of a short sample processing time (～3.5 h) and limited transfer of residual sample matrix into the Hg trapping solution. This in turn limits matrix interferences on the Hg reduction efficiency of the cold vapor generator used for Hg isotopic analysis.     

Mercury analysis in environmental samples by EDXRF and CV-AAS

The analysis of total Hg in various environmental matrices was investigated using energy dispersive X-ray fluorescence (EDXRF) for both powdered and digested samples and cold vapor atomic absorption (CV-AAS) for digested samples. Several microwave decomposition procedures were evaluated with respect to the determination of Hg by CV-AAS and EDXRF. The use of different acid mixtures, microwave power settings and decomposition times were compared as well as the analysis on wet and freeze-dried samples. A set of standard reference samples were used to evaluate the procedures: NBS Citrus leaves (1572), NRC Pine needles (1575), NRC Dogfish muscle tissue (DORM-2), NRC Dogfish liver tissue (DOLM-2), BCR Human hair (397), BCR Coking coal (181) and NRC Marine sediment (PACS-1). An H₂SO₄/HNO₃/H₂O₂ acid mixture was found to be optimal for the complete mineralization and digestion of biological samples for Hg by CV-AAS whereas for EDXRF both the HNO₃/H₂O₂ and H₂SO₄/HNO₃/H₂O₂ acid mixture gave good results. The detection limit of EDXRF could significantly be decreased (from 0.2 μg/g to 0.058 μg/g) by performing the analysis with digested samples. A good agreement was obtained between CV-AAS and EDXRF analysis. The obtained results were also in good agreement with certified values. The methods were applied to environmental samples (coal, trees, leaves, spinach, fish, sediments) and human hair in a coal mining area and in places where they use coal for cooking in Vietnam. Received: 24 February 1997 / Revised: 13 June 1997 / Accepted: 18 June 1997     

Adsorption behavior of Co and C2H2 on the graphite basal surface: A quantum chemistry study

The adsorption of CO and C₂H₂ molecules on the perfect basal surface of graphite is investigated by adopting cluster models in conjunction with quantum chemical calculations. The noncovalent interaction potential energy curves for three different orientations of CO and C₂H₂ molecules with respect to the inert basal plane of graphite are calculated via semi-empirical and Möller-Plesset ab initio methods. Then, we have considered the effects of interaction energies on the C≡O and C≡C bond lengths by performing the partial geometry optimization procedure on the CO-graphite and C₂H₂-graphite systems in various intermolecular distances. The computational analysis of all physical noncovalent potential energy curves reveals that the relative configurations in which CO and C₂H₂ molecules approach the graphite sheet from out of the plane have stronger interaction energy and so is more favorable from the energetic viewpoint. This means that the graphite layer prefers to increase its thickness via the chemical vapor deposition of CO and C₂H₂ on the graphite.     

A Highly Efficient Friedel–Crafts Reaction of 3‐Hydroxyoxindoles and Aromatic Compounds to 3,3‐Diaryl and 3‐Alkyl‐3‐aryloxindoles Catalyzed by Hg(ClO4)2⋅3 H2O

We report a highly efficient Friedel–Crafts reaction of 3‐alkyl or 3‐aryl 3‐hydroxyoxindoles with a variety of aromatic and heteroaromatic compounds to unsymmetrical 3,3‐diaryloxindoles or 3‐alkyl‐3‐aryloxindoles, which are interesting medicinal targets and useful building blocks for the synthesis of natural products. Hg(ClO₄)₂ ? 3 H₂O was identified as a powerful catalyst for this reaction, and is significantly more efficient than other screened metal perchlorate hydrates and Brønsted acids such as HOTf and HClO₄. The high catalytic property of Hg(ClO₄)₂ ? 3 H₂O originates from the unprecedented dual activation effects of aromatic mercuration, which could generate a strong protic acid to facilitate the generation of a carbocation at the C3‐position of oxindoles and simultaneously form the more reactive nucleophilic reaction partner.     

Water Stable Zr–Benzenedicarboxylate Metal–Organic Frameworks as Photocatalysts for Hydrogen Generation

The Zr‐containing metal–organic frameworks (MOFs) formed by terephthalate (UiO‐66) and 2‐aminoterephthalate ligands [UiO‐66(NH₂)] are two notably water‐resistant MOFs that exhibit photocatalytic activity for hydrogen generation in methanol or water/methanol upon irradiation at wavelength longer than 300 nm. The apparent quantum yield for H₂ generation using monochromatic light at 370 nm in water/methanol 3:1 was of 3.5 % for UiO‐66(NH₂). Laser‐flash photolysis has allowed detecting for UiO‐66 and UiO‐66(NH₂) the photochemical generation of a long lived charge separated state whose decay is not complete 300 μs after the laser flash. Our finding and particularly the influence of the amino group producing a bathochromic shift in the optical spectrum without altering the photochemistry shows promises for the development of more efficient MOFs for water splitting.     

Novel mercury(II) complexes of meso-tetraphenylporphyrin and N-methylporphyrins

Treatment of meso-tetraphenylporphyrin, H₂TPP, with just over one equivalent of mercury(II) acetate in methylene chloride-THF gives mercury(II) meso-tetraphenylporphyrin, HgTPP. With excess of mercury(II) acetate, H₂TPP and HgTPP afford a novel dimetallic mononuclear porphyrin, AcOHgTPPHgOAc. In contrast, HgTPP reacts with mercury(II) chloride to give the chloro-analogue, ClHgTPPHgCl, but there is no reaction between H₂TPP and mercury(II) chloride. Demetallation of HgTPP in methylene chloride containing small amounts of hydrogen chloride proceeds via the dimetallic compound, ClHgTPPHgCl, to give free base HTPP. The reaction rate is dependent upon acid concentration suggesting that the rate determining step is protonation, but dilution causes no decrease in the rate; a mechanism which invokes the intermediacy of monohydrogen-meso-tetraphenylporphyrinatomercury(II) chloride, H(TPP)HgCl, in the formation of ClHgTPPHgCl and in its subsequent decomposition into H₂TPP, is proposed.N-Methylporphyrins react with mercury(II) acetate in methylene chloride-tetrahydrofuran to give the corresponding N-methylporphyrinatomercury(II) acetates, Me(P)HgOAc.     

The effect of surface electronic structures of Au/TiO2 on sonophotochemical reactions

The photo-excited surface charges do not play the primary roles in enhancing the sonophotochemical reduction of water.     

A Cross‐linked Conjugated Polymer Photosensitizer Enables Efficient Sunlight‐Induced Photooxidation

Photooxidation under sunlight has potential in organic synthesis, bacterial killing, and organic waste treatment. Photosensitizers (PSs) can play an important role in this process. High ¹O₂ generation efficiency and excellent photostability under sunlight, as well as easy recyclability are ideal properties for PSs, but are not easy to achieve simultaneously. Herein, a pure organic porous conjugated polymer PS, CPTF, shows great photostability, large specific surface area, and high ¹O₂ generation efficiency under sunlight for photooxidation. For the oxidation of aromatic aldehyde to aromatic acid, the PS catalyst shows excellent recyclability, and enables solvent‐free reactions in high yields both under direct sunlight and simulated AM 1.5G irradiation. In addition, the successful application of CPTF as an antibacterial agent and organic waste decomposition under simulated AM 1.5G irradiation indicates the potential of CPTF in sunlight‐induced waste water treatment.     

Electrochemiluminescence of Tris(2,2′‐bipyridine)ruthenium with Various Co‐reactants under Ultrasound Irradiation

Electrochemiluminescence (ECL) of tris(2,2′‐bipyridine)ruthenium, Ru(bpy)₃²⁺ in the presence of various co‐reactants, such as tripropylamine (TPA), oxalate ion (C₂O₄^2?), ascorbic acid (H₂A) and dehydroascorbic acid (DHA), were investigated under ultrasound irradiation. In sono‐ECL experiments, an indium‐thin‐oxide (ITO) was used as working electrode, and a titanium tipped sonic horn probe (diameter 2 mm) which operated at a frequency of 20 kHz was set in the front of the ITO electrode. Under the ultrasound irradiation, ECL signals were found to be significantly enhanced when TPA and C₂O₄^2? were used as co‐reactants, only slightly enhanced in Ru(bpy)₃²⁺/DHA system, but total quenched in Ru(bpy)₃²⁺/H₂A system. The difference of Ru(bpy)₃²⁺ ECL behaviors for various co‐reactant could to be due to the different kinetics of catalytic reactions associated in ECL schemes. ECL quenching effect observed in Ru(bpy)₃²⁺/H₂A system was suggested to be due to electron transfer (ET) route between the excited state *Ru(bpy)₃²⁺ and ascorbate anion HA^? diffused from the bulk solution, where the diffusional HA^? species served as electron donor. The effect becomes more pronounced upon sonication because the effective collision frequency between *Ru(bpy)₃²⁺ and HA^? would be significantly increased by the enhanced mass transport effect of ultrasound.     

Electrochemical Synthesis of Co-intercalation Compounds in the Graphite-H<Subscript>2</Subscript>SO<Subscript>4</Subscript>-H<Subscript>3</Subscript>PO<Subscript>4</Subscript>System

Anodic oxidation of highly oriented pyrolytic graphite in an electrolyte containing concentrated sulfuric and anhydrous phosphoric acids is studied for the first time. The synthesis was carried out under galvanostatic conditions at a current I = 0.5 mA and an elevated temperature (t = 80°C). Intercalation compounds of graphite (ICG) are shown to form at all concentration ratios of H₂SO₄ and H³PO⁴ acids. The intercalation compound of step I forms in solutions containing more than 80 wt % H₂SO₄, a mixture of compounds of intercalation steps I and II forms in 60% H²SO⁴, intercalation step II is realized in the sulfuric acid concentration range from 10 to 40%, and a mixture of compounds of intercalation steps III and II is formed in 5% H₂SO₄ solutions. The threshold concentration of H₂SO₄ intercalation is ∼2%. With the decrease in active intercalate (H₂SO₄) concentration, the charging curves are gradually smoothed, the intercalation step number increases, and the potentials of ICG formation also increase. As the sulfuric acid concentration in the electrolyte changes from 96 to 40 wt %, the filled-layer thickness d _i in ICG monotonously increases from 0.803 to 0.820 nm, which apparently is associated with the greater size of phosphoric acid molecules. With further increase in H₃PO₄ concentration in solution, d _i remains unchanged. According to the results of chemical analysis, both acids are simultaneously incorporated into the graphite interplanar spacing and their ratio in ICG is determined by the electrolyte composition.__________Translated from Elektrokhimiya, Vol. 41, No. 5, 2005, pp. 651–655.Original Russian Text Copyright © 2005 by Leshin, Sorokina, Avdeev.     

Biofortification of Three Cultivated Mushroom Species with Three Iron Salts—Potential for a New Iron-Rich Superfood

Mushrooms fortified with iron (Fe) can offer a promising alternative to counter the worldwide deficiency problem. However, the factors that may influence the efficiency of fortification have not yet been fully investigated. The aim of this study was to compare the effects of three Fe forms (FeCl₃ 6H₂O, FeSO₄ 7H₂O, or FeHBED) in three concentrations (5, 10, or 50 mM) for three mushroom species (Pleurotus eryngii, P. ostreatus, or Pholiota nameko) on their chemical composition, phenolic compounds, and organic acid production. The most effective metal accumulation of all the investigated species was for the 50 mM addition. FeCl₃ 6H₂O was the most favorable additive for P. eryngii and P. nameko (up to 145 and 185% Fe more than in the control, respectively) and FeHBED for P. ostreatus (up to 108% Fe more than in control). Additionally, P. nameko showed the highest Fe accumulation among studied species (89.2 ± 7.51 mg kg⁻¹ DW). The creation of phenolic acids was generally inhibited by Fe salt supplementation. However, an increasing effect on phenolic acid concentration was observed for P. ostreatus cultivated at 5 mM FeCl₃ 6H₂O and for P. eryngii cultivated at 5 mM FeCl₃ 6H₂O and 5 mM FeSO₄ 7H₂O. In the case of organic acids, a similar situation was observed. For P. ostreatus, FeSO₄ 7H₂O and FeHBED salts increased the formation of the determined organic acids in fruiting bodies. P. eryngii and P. nameko were characterized by a much lower content of organic acids in the systems supplemented with Fe. Based on the obtained results, we recommend starting fortification by preliminarily indicating which form of the element is preferred for the species of interest for supplementation. It also seems that using an additive concentration of 50 mM or higher is most effective.