Determination of Cd by electrothermal atomic absorption spectrometry after electrodeposition on a graphite probe modified with palladium

Traces of Cd were determined by electrothermal atomic absorption spectrometry after electrochemical preconcentration on a commercial graphite ridge probe modified with Pd. The Pd electrochemically deposited on the probe surface served not only as the modifier but it also protected the graphite surface. Cd was electrodeposited at a controlled potential − 1.2 V (vs. saturated calomel electrode) using the Pd-modified graphite probe as a working electrode. The sensitivity of Cd determination remained unchanged for 300 electrodeposition and atomization cycles. The detection limit (3σ_blank) was improved with increasing time of electrolysis and was 1.2 ng l^− 1 for a 10 min electrolysis time in the presence of 0.1 mol l^− 1 NaNO₃. The procedure was applied for the determination of Cd in (1 + 1) diluted seawater and in (1 + 1) diluted urine samples using the standard addition method.     

Simultaneous on-line preconcentration and determination of trace metals in environmental samples using a modified nanometer-sized alumina packed micro-column by flow injection combined with ICP-OES

A novel organic reagent 3-(8-quinolinylazo)-4-hydroxybenzoic acid (QAHBA) was synthesized for chemically modified nanometer-sized alumina, and it was characterized with infrared spectrum and ¹H NMR spectra. By using modified nanometer-sized alumina as micro-column packing material, a new method of flow injection (FI) on-line preconcentration coupled to ICP-OES was developed for simultaneous determination of trace metals (Ag, Pd, Au, Ga, In and Nb) in geological and environmental samples. The effects of pH, sample flow rate, sample volume, elution and interfering ions on the recovery of the analytes have been investigated. Under the optimized operating conditions, the adsorption capacity of the modified nanometer-sized alumina for Ag, Pd, Au, Ga, In and Nb were found to be 5.1, 7.6, 17.7, 15.6, 8.1 and 12.3 mg g⁻¹, respectively. With 4 min preconcentration time and 24 s elution time, the enrichment factor was 10 and the sample frequency was 10 h⁻¹. The detection limits of this method for Ag, Pd, Au, Ga, In and Nb were 0.12, 0.44, 0.27, 0.19, 0.54 and 0.18 μg l⁻¹, respectively, while the R.S.D.s were 1.6, 2.3, 4.5, 1.6, 1.9 and 1.7% (n = 7, c = 50 ng ml⁻¹), respectively. The proposed method has been applied to the determination of these trace metals in geological-certified reference materials and natural water samples with satisfactory results.     

Preconcentration of palladium in a flow-through electrochemical cell for determination by graphite furnace atomic absorption spectrometry

An electrochemical preconcentration at a controlled potential on the electrode in a flow-through mode followed by graphite furnace atomic absorption spectrometric (GFAAS) detection is proposed for determination of trace amounts of palladium. After electrolysis the polarization of the electrodes was changed and deposited metal was dissolved electrochemically in the presence of an appropriate stripping reagent. Conditions for the electrodeposition, such as pH of the solutions, a deposition potential, dissolution potential and a composition of stripping solution were optimised. The graphite electrode (GE) and glassy carbon electrode (GCE) were tested for the palladium reduction process. The detection limit of 0.05 ng ml⁻¹ Pd (1 pg) was obtained after palladium preconcentration on the GCE and dissolution with 0.2 mol l⁻¹ thiourea in 0.1 mol l⁻¹ HCl followed by GFAAS detection. The method was applied for the determination of palladium in spiked tap water and road dust samples.     

n-Alkanes, PAHs and surfactants in the sea surface microlayer and sea water samples of the Gerlache Inlet sea (Antarctica)

Sea surface microlayer (SML) and sea water samples (SSW) collected in the Gerlache Inlet Sea (Antarctica) were analysed for n-alkanes and polycyclic aromatic hydrocarbons (PAHs). The SML is a potential enrichment site of hydrophobic organic compounds compared to the underlying water column. Total concentration ranges of n-alkanes and PAHs (dissolved and particulate) in subsurface water (− 0.5 m depth) were 272-553 ng l^− 1 (mean: 448 ng l^− 1) and 5.27-9.43 ng l^− 1 (mean: 7.06 ng l^− 1), respectively. In the SML, the concentration ranges of n-alkanes and PAHs were 353-968 ng l^− 1 (mean: 611 ng l^− 1) and 7.32-23.94 ng l^− 1 (mean: 13.22 ng l^− 1), respectively. To evaluate possible PAH contamination sources, specific PAH ratios were calculated. The ratios reflected a predominant petrogenic input. A characterisation of surface active substances was also performed on SML and SSW samples, both by gas bubble extraction, and by dynamic surface tension measurements. Results showed a good correlation between n-alkanes, PAHs and refractory organic matter.     

Determination of ultra-trace gold in natural water by graphite furnace atomic absorption spectrophotometry after in situ enrichment with thiol cotton fiber

A simple method of determining ultra-trace Au in natural water was presented by using graphite furnace atomic absorption spectrophotometry (GFAAS) after in situ enrichment with thiol cotton fiber (TCF). The sample solution was adjusted to pH 1.5-2.0 with HCl, then the water sample was passed through a column packed with 0.10-0.20 g TCF and the flow rate was controlled at 20-40 ml min⁻¹. The effects of interferences, such as complexing and oxidizing agents and other elements adsorbed on TCF were overcome by chemical treatments prior to the desorption of Au. The adsorbed Au was adsorbed with 2.0 ml hot acid, then it was extracted with 1.00 ml methyl isobutylketone (MIBK). For a 5 l water sample, the detection limit of Au is 0.02 ng l⁻¹. The relative standard deviation (R.S.D.) for the determination of 1.44 ng l⁻¹ Au was 9.4%.The method was applied to determine ultra-trace Au both in suspended phase and soluble phase in natural water, the concentrations of total Au in natural water samples range from 0.51 to 67.82 ng l⁻¹. The recovery of added 0.50-6.00 ng l⁻¹ Au was 80-95%. The method is useful in prospecting for Au deposits by means of hydrogeochemical methods. The enrichment is carried out in the field, and then the determination of Au is completed later in the laboratory.     

A piezoelectric immunosensor for the determination of pesticide residues and metabolites in fruit juices

A quartz crystal microbalance (QCM) immunosensor was developed for the determination of the insecticide carbaryl and 3,5,6-trichloro-2-pyridinol (TCP), the main metabolite of the insecticide chlorpyrifos and of the herbicide triclopyr. The detection was based on a competitive conjugate-immobilized immunoassay format using monoclonal antibodies (MAbs). Hapten conjugates were covalently immobilized, via thioctic acid self-assembled monolayer (SAM), onto the gold electrode sensitive surface of the quartz crystal. This covalent immobilization allowed the reusability of the modified electrode surface for at least one hundred and fifty assays without significant loss of sensitivity. The piezoimmunosensor showed detection limits (analyte concentrations producing 10% inhibition of the maximum signal) of 11 and 7 μg l⁻¹ for carbaryl and TCP, respectively. The sensitivity attained (I₅₀ value) was around 30 μg l⁻¹ for both compounds. Linear working ranges were 15-53 μg l⁻¹ for carbaryl and 13-83 μg l⁻¹ for TCP. Each complete assay cycle took 20 min. The good sensitivity, specificity, and reusability achieved, together with the short response time, allowed the application of this immunosensor to the determination of carbaryl and TCP in fruits and vegetables at European regulatory levels, with high precision and accuracy.     

Multiwalled carbon nanotubes microcolumn preconcentration and determination of gold in geological and water samples by flame atomic absorption spectrometry

The potential of multiwalled carbon nanotubes (MWNTs) as solid-phase extraction adsorbent for the separation and preconcentration of gold has been investigated. Gold could be adsorbed quantitatively on MWNTs in the pH range of 1–6, and then eluted completely with 2 mL of 3% thiourea in 1 mol L^− 1 HCl solution at a flow rate of 0.5 mL min^− 1. A new method using a microcolumn packed with MWNTs as sorbent has been developed for the preconcentration of trace amount of Au prior to its determination by flame atomic absorption spectrometry. Parameters influencing the preconcentration of Au, such as pH of the sample, sample flow rate and volume, elution solution and interfering ions, have been examined and optimized. Under the optimum experimental conditions, the detection limit of this method for Au was 0.15 µg L^− 1 with an enrichment factor of 75, and the relative standard deviation (R.S.D) was 3.1% at the 100 µg L^− 1 Au level. The method has been applied for the determination of trace amount of Au in geological and water samples with satisfactory results.     

Determination of arsenic in gold samples using matrix exchange differential pulse stripping voltammetry

A method comprising matrix exchange differential pulse stripping voltammetry (DPSV) at a gold film electrode has been proposed for the determination of small quantities of arsenic in pure gold. A wall-jet cell (WJC) and an on-line deoxygenation system were used to facilitate matrix exchange. The gold(I) cyanide complex was formed to avoid gold deposition on the electrode together with the arsenic. The pH of the sample solutions were adjusted to 3, as alkaline solutions gold(I) cyanide produced interference and the uncomplexed cyanide led to passivation of the gold film electrode. Matrix exchange electrolytes consisting of 4 mol l⁻¹ hydrochloric acid or a combination of 2 mol l⁻¹ sulphuric acid and 0.2 mol l⁻¹ hydrochloric acid could be utilised. Arsenic concentrations as low as 0.1 mg l⁻¹, could readily be detected in a gold matrix with a 60 s deposition time. While, cobalt and silver did not interfere with the arsenic determination, copper interfered even when present at similar concentrations to that of arsenic.     

Localized surface plasmon resonance sensing detection of glucose in the serum samples of diabetes sufferers based on the redox reaction of chlorauric acid

In this paper, the formation of gold nanoparticles (Au NPs) as a result of the thermo-active redox reaction of chlorauric acid (HAuCl₄) and glucose in alkaline medium was identified by measuring the plasmon resonance absorption, localized surface plasmon resonance (LSPR), and transmission electron microscopy (TEM) images, for the formation of Au NPs displays characteristic plasmon resonance absorption bands and corresponding LSPR signals. It was found that the resulted LSPR signals could be easily detected with a common spectrofluorometer. With increasing glucose concentration, the LSPR intensity displays linear response with the glucose content over the range from 2.0 to 250.0 μmol l⁻¹. Thus, a novel assay of glucose was established with the limits of determination (3σ) being 0.21 μmol l⁻¹, and the detection of glucose could be made easily in the serum samples of diabetes sufferers. Mechanism investigations showed that the activation energy and molar ratio of the reaction were 34.8 kJ mol⁻¹ and 3:2, respectively.     

Fabrication and characterisation of high performance polypyrrole modified microarray sensor for ascorbic acid determination

In this study, gold microelectrode array (Au/MEA) with electrode of 12 μm diameter was fabricated by photolithography technique. Subsequently, polypyrrole (Ppy) modified gold microarrays sensor (Ppy/Au/MEA) was prepared by cyclic voltammetry technique. The deposition potential range and number of cycles were optimised in order to get optimum thickness of Ppy film. Scanning Electron Microscope and Atomic Force Microscope investigations reveal that Ppy coating formed at 3 cycles is porous with thickness of 1.5 μm which exhibiting high catalytic current for ascorbic acid (AA) in square wave technique (SWV). In contrast to earlier sensors designs, these Ppy/Au/MEA sensors exhibits lower detection limit (LOD) of 10 nm towards AA at physiological conditions. It also exhibits enhanced sensitivity (2.5 mA cm⁻² mM⁻¹) and long range of linear detection limit from 10 nm to 2.8 mM. In the same way, polypyrrole modified macro Au (Ppy/Au/MA) biosensor was also fabricated and its electro catalytic property towards AA was compared with that of Ppy/Au/MEA. The Ppy/Au/MA exhibits sensitivity of only 0.27 mA cm⁻² mM⁻¹, LOD of 5 μM and linear range of 10 μM to 2.2 mM. Hence, our investigations indicate that the Ppy/Au/MEA could serve as highly sensitive sensor for AA than any of the earlier designs. So, the Ppy/Au/MEA electrode was utilised for determination AA in a wide variety of real samples.     

Differential pulse voltammetric determination of trace Te(IV) at a poly(3,3′-diaminobenzidine) film modified gold electrode in flow systems

Electropolymerization of 3,3′-diaminobenzidine on a gold surface gave an adherent, stable film of poly(3,3′-diaminobenzidine) (PDAB). This polymer film retained the complexational functionalities of its monomer, demonstrating preconcentration abilities for several ions, including Se(IV) and Te(IV). In particular, in this work, continuous flow and flow injection methods were developed for the sensitive and selective determination of Te(IV). The optimized method for the continuous flow mode had a detection limit of 5.6×10⁻⁹ mol l⁻¹ for 10 min preconcentration. Typical relative standard deviations for six consecutive determinations were 1.82 and 2.56% for Te(IV) concentrations of 1.0×10⁻⁶ and 5.0×10⁻⁸ mol l⁻¹, respectively (10 min preconcentration). The method was applied to the determination of Te(IV) in real samples.     

Electroanalysis of dopamine at a gold electrode modified with N-acetylcysteine self-assembled monolayer

Voltammetric behavior of dopamine (DA) on a gold electrode modified with the self-assembled monolayer (SAM) of N-acetylcysteine has been investigated, and one pair of well-defined redox peaks of dopamine is obtained at the SAM modified gold electrode. The oxidation peak current increases linearly with the concentration of dopamine in the range of  mol l⁻¹. The detection limit is 8.0×10⁻⁷ mol l⁻¹. This method will be applicable to the determination of dopamine in injection of dopamine hydrochloride, and the good recovery of dopamine is obtained. Furthermore, The SAM modified gold electrode can resolve well the voltammetric responses of dopamine and ascorbic acid (AA), so it can also be applied to the determination of dopamine in the presence of ascorbic acid.     

Determination of platinum and palladium in road dust after their separation on immobilized fungus by electrothermal atomic absorption spectrometry

A flow solid phase extraction procedure based on biosorption of Pt(IV) and Pd(II) on Aspergillus sp. immobilized on cellulose resin Cellex-T was proposed for the separation and preconcentration of Pt and Pd before their determination by electrothermal atomic absorption spectrometry (ETAAS). The analytical conditions including sample pH, eluent type, flow rates of sample and eluent solutions were examined. The analytes were selectively retained on the biosorbent in acidic medium (pH 1) and subsequently eluted from the column with 1 mL of thiourea solution (0.25 mol L^− 1 thiourea in 0.3 mol L^− 1 HCl). The reproducibility of the procedure was below 5%. The limit of detection of the method was 0.020 ng mL^− 1 for Pt and 0.012 ng mL^− 1 for Pd. The method validation was performed by analysis of certified reference materials BCR-723 (tunnel dust) and SARM-76 (platinum ore). The developed separation procedure was applied to the determination of Pt and Pd in road dust samples by ETAAS.The applied biosorbent is characterized by high sorption capacity: 0.47 mg g^− 1 for Pt and 1.24 mg g^− 1 for Pd.     

Synthesis of amidinothioureido-silica gel and its application to flame atomic absorption spectrometric determination of silver, gold and palladium with on-line preconcentration and separation

A simple and highly selective flow injection (FI) on-line preconcentration and separation flame atomic absorption spectrometric (FAAS) method was developed for the determinations of trace amounts of silver, gold and palladium. The selective preconcentration of the noble metals was achieved in a wide range of sample acidity (0.1-6 M HNO₃ or HCl) on a microcolumn packed with amidinothioureido-silica gel (ATuSG). The analytes retained on the column were effectively eluted with 5.0% thiourea solution. The analytical procedure was optimized for sample acidity, elution, interferences, flow rate of sampling and eluting, and concentration of sample. Common co-existing cations and anions did not interfere with the preconcentration and determination of the three metals. At a sample loading flow rate of 4.5 ml min⁻¹ with 60 s preconcentration, detection limits (3σ) of 1.1 ng ml⁻¹ Ag, 13 ng ml⁻¹ Au and 17 ng ml⁻¹ Pd were obtained. The precisions (R.S.D., n=11) were 1.2% for Ag, 1.2% for Au and 1.7% for Pd, respectively. The detection limits can be further improved by increasing sample volume. The analytical results obtained by the proposed method for a number of standard reference materials were in good agreement with the certified values.     

Colloidal-gold cysteamine-modified carbon paste electrodes as suitable electrode materials for the electrochemical determination of sulphur-containing compounds Application to the determination of methionine

The suitability of colloidal-gold cysteamine-modified carbon paste electrodes (nAu-Cyst-CPE) for the electrochemical determination of sulphur-containing compounds is illustrated in this work by determining the amino acid methionine in real samples, as well as a methionine-based peptide. Voltammograms from methionine solutions at nAu-Cyst-CPE exhibited improved electroanalytical characteristics when compared with colloidal-gold cysteamine-modified Au disk electrodes (nAu-Cyst-AuE). Differential pulse voltammetry in phosphate buffer of pH 7.0 was used for the determination of methionine, with a range of linearity of (1.0-100) × 10⁻⁶ mol l⁻¹ and a detection limit of 5.9 × 10⁻⁷ mol l⁻¹. This detection limit is remarkably lower than those reported previously using other modified electrodes or amperometric detection. Methionine peptides also exhibited anodic peaks suitable to detect this kind of molecules. Methionine was determined with good results in a pharmaceutical product containing several vitamins, amino acids and other compounds, and in spiked meat peptone, a complex sample containing enzimatically digested protein.     

Determination of gold by nanometer titanium dioxide immobilized on silica gel packed microcolumn and flame atomic absorption spectrometry in geological and water samples

A new method has been developed for the determination of gold based on separation and preconcentration with a microcolumn packed with nanometer TiO₂ immobilized on silica gel (immobilized nanometer TiO₂) prior to its determination by flame atomic absorption spectrometry. The optimum experimental parameters for preconcentration of gold, such as pH of the sample, sample flow rate and volume, eluent and interfering ions, have been investigated. Gold could be quantitatively retained by immobilized nanometer TiO₂ in the pH range of 8-10, then eluted completely with 0.1 mol L⁻¹ HNO₃. The detection limit of this method for Au was 0.21 ng mL⁻¹ with an enrichment factor of 50, and the relative standard deviation (R.S.D.) was 1.8% at the 100 ng mL⁻¹ Au level. The method has been applied for the determination of trace amounts of Au in geological and water samples with satisfactory results.     

Evaluation of liquid chromatography inductively coupled plasma mass spectrometry for arsenic speciation in water from industrial treatment of shale

This work describes an arsenic speciation analysis in aqueous effluent from a shale industrial plant using liquid chromatography coupled to inductively coupled plasma mass spectrometry (LC–ICP–MS). Arsenic species have been separated through an anion-exchange column and several parameters investigated, such as retention time, pH, flow rate and concentration of the mobile phase (ammonium carbonate), chloride interference and column conditioning time. The best conditions have been found by fixing the pH of the mobile phase at 8.7. Keeping the mobile phase flow rate at 1.5 ml min^− 1, arsenic species were separated by varying the concentration of the mobile phase and the time of elution, as follow: 1.5 mmol l^− 1 for 10 min, 12 mmol l^− 1 for 10 min and 20 mmol l^− 1 for 10 min, respectively. Up to 13 As species present in the samples were separated under these conditions and the following species could be identified and quantified: arsenite [As(III)], dimethylarsinic acid (DMA), monomethylarsonic acid (MMA) and arsenate [As(V)]. The limits of detection of the LC–ICP–MS method were 0.02, 0.06, 0.04 and 0.10 μg l^− 1 of As(III), DMA, MMA, and As(V), respectively. The concentration of these species in the samples were from 3.7 to 6.4 μg l^− 1, 6.9 to 13.2 μg l^− 1, 100 to 142 μg l^− 1 and 808 to 1363 μg l^− 1 for As(III), DMA, MMA and As(V), respectively. The accuracy, evaluated by recovery tests, varied from 94 to 105% and the precision, evaluated by the relative standard deviation was typically lower than 10%.     

Determination of traces of palladium in stream sediment and auto catalyst by FI-ICP-OES using on-line separation and preconcentration with QuadraSil TA

A flow injection analysis (FIA) method using on-line separation and preconcentration with a novel metal scavenger beads, QuadraSil™ TA, has been developed for the ICP-OES determination of traces of palladium. QuadraSil TA contains diethylenetriamine as a functional group on spherical silica beads and shows the highest selectivity for Pd(II) at pH 1 (0.1 mol l⁻¹ hydrochloric acid) solution. An aliquot of the sample solution prepared as 0.1 mol l⁻¹ in hydrochloric acid was passed through the QuadraSil TA column. After washing the column with the carrier solution, the Pd(II) retained on the column was eluted with 0.05 mol l⁻¹ thiourea solution and the eluate was directly introduced into an ICP-OES. The proposed method was successfully applied to the determination of traces of palladium in JSd-2 stream sediment certified reference material [0.019 ± 0.001 μg g⁻¹ (n = 3); provisional value: 0.0212 μg g⁻¹] and SRM 2556 used auto catalyst certified reference material [315 ± 4 μg g⁻¹ (n = 4); certified value: 326 μg g⁻¹]. The detection limit (3σ) of 0.28 ng ml⁻¹ was obtained for 5 ml of sample solution. The sample throughputs for 5 ml and 100 μl of the sample solutions were 10 and 15 h⁻¹, respectively.     

On-line electrochemical preconcentration and flame atomic absorption spectrometric determination of manganese in urine samples

A sensitive and selective method was developed for the determination of traces of manganese in urine using on-line electrochemical preconcentration followed by flame atomic absorption spectrometry detection. A home made flow-through polypropylene cell (4.5 cm long × 0.8 cm diameter filled with glass marbles) with an effective inner volume of 0.5 ml containing a working and a counter electrode, both of glassy carbon and a Pt pseudo reference electrode was located in a flow injection manifold specially designed for the purpose of this work. The manganese was deposited from buffer solution of NH₃/NH₄Cl at pH 9.00 through an oxidizing process at a current of 400 mA during 7 min. A flow of HCl 0.1 mol l⁻¹ at 4 ml min⁻¹ through the cell, chemically dissolved the deposit. A small portion (15 μl) of the concentrate was introduced in a continuously flowing system by means of a timing device and was then carried to the detector for the manganese quantification. All electrochemical and spectroscopic variables as well as possible interferences in both systems were systematically studied. The relative standard deviations for ten consecutive measurements of manganese solutions of 2.0 and 20 μg l⁻¹ were of 2.3 and 1.5%, respectively, while for a sample processed five times was less then 5%. The accuracy of the developed procedure was evaluated by adding known amounts of manganese standard to urine samples and following the whole procedure. Recoveries within the range 97.2-102.8% were obtained. To further prove the accuracy, a Seronorm Trace Elements in Urine, Batch 403125 sample with a reported concentration of 13 μg Mn l⁻¹ was also analyzed. The experimental value obtained was of 12.7 ± 0.1 μg l⁻¹, which does not differ significantly from the reported amount (p < 0.05). A preconcentration factor of 40, a linear range between 0.015 and 60 μg l⁻¹ and a limit of detection of 15 ng l⁻¹ permitted the determination of manganese in real urine samples from non-exposed subjects in the range 0.5-2.8 μg l⁻¹.     

Development of a voltammetric sensor for diospyrin determination in nanomolar concentrations

A sensor based on glassy carbon (GC) electrode modified with cobalt tetrasulfonated phthalocyanine (CoTSPc) and a poly-l-lysine (PLL) film is proposed for diospyrin determination in nanomolar concentrations with differential pulse voltammetry (DPV) technique. The modified electrode showed excellent catalytic activity presenting much higher peak currents than those measured on a bare GC electrode. Linear response range, sensitivity and limit of detection (LOD) were of 1-120 nmol l⁻¹, 220.46 nA l nmol⁻¹ cm⁻² and 0.3 nmol l⁻¹, respectively. The repeatability of the proposed sensor, evaluated in term of relative standard deviation (R.S.D.), was measured as 4.4% for 10 experiments in 50 μmol l⁻¹ diospyrin samples. The developed sensor was applied for the determination of diospyrin in the crude extracts of the stem-bark of Diospyros montana Roxb. and the average recovery for these samples was 101.9 (±3.1)%.