Layer-by-layer assembly of UV-resistant poly(3,4-ethylenedioxythiophene) thin films

The layer-by-layer assembly technique was used to create electrically conductive films with poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate) (PEDOT-PSS) and branched polyethylenimine (BPEI). Titanium dioxide (TiO(2)) and carbon black were used to prevent UV-degradation of these PEDOT-PSS thin film assemblies. Film growth and conductivity were studied, while varying composition and examining the effect of UV absorbing particles on the electrical conductivity. All films showed similar initial sheet resistances, but after exposure to 365 nm UV light for 9 days (correlating to approximately 4 years of sunlight), the films containing TiO(2) were up to 250 times more conductive. Additionally, the TiO(2) containing films were 27% more optically transparent than films made with PEDOT in the absence of TiO(2). The addition of colloidal titania allows the useful life of the PEDOT films to be extended without the detrimental effects of decreased transparency. Doping the PEDOT with dimethylsulfoxide produced eight bilayer films that were almost 6 times more conductive. However, the degradation rate for the doped PEDOT films without TiO(2) was 10 times greater than the doped films with TiO(2).     

Uniform thin films of poly-3,4-ethylenedioxythiophene (PEDOT) prepared by in-situ deposition

In-situ deposited thin films of the conducting polymer poly-3,4-ethylenedioxythiophene (PEDOT) have been prepared on hydrophilic and hydrophobic substrates and characterized by UV-Vis spectroscopy, atomic force microscopy and resistivity measurements.     

Time-scale- and temperature-dependent mechanical properties of viscoelastic poly(3,4-ethylenedioxythiophene) films

The viscoelastic properties of thin films of poly(3,4-ethylenedioxythiophene) (PEDOT) have been studied using the method of acoustic impedance. The films were deposited on the Au electrodes of 10 MHz AT-cut quartz thickness shear mode resonators and exposed to acetonitrile solutions of 0.1 M TEABF4 and LiClO4. For p-doped films, admittance spectra as a function of potential (E), temperature (T), and time scale (frequency, via harmonics, in the range 10-110 MHz) were acquired. Shear modulus components extracted from these responses surprisingly showed virtually no variation with E (and thus film solvation) or with T, but the variation with frequency was dramatic. This qualitative behavior and the numerical values of the shear moduli contrast strongly with recently reported data for the related poly(3-hexylthiophene) system, which shares the same conducting spine but differs substantially in the substitution pattern. Accordingly, the models and interpretation for PEDOT are quite different: film dynamics are determined by free-volume effects, and side-chain motion is not a significant factor. Qualitatively similar potential and time-scale effects were seen for n-doped PEDOT, but the scope of the measurements was limited by film stability.     

Potential-modulated, attenuated total reflectance spectroscopy of poly(3,4-ethylenedioxythiophene) and poly(3,4-ethylenedioxythiophene methanol) copolymer films on indium-tin oxide

We report the first application of a potential-modulated spectroelectrochemical ATR (PM-ATR) instrument utilizing multiple internal reflections at an optically transparent electrode to study the charge-transfer kinetics and electrochromic response of adsorbed films. A sinusoidally modulated potential waveform was applied to an indium-tin oxide (ITO) electrode while simultaneously monitoring the optical reflectivity of thin (2-6 equivalent monolayers) copolymer films of poly(3,4-ethylenedioxythiophene) (PEDOT) and poly(3,4-ethylenedioxythiophene methanol) (PEDTM), previously characterized in our laboratory. At high modulation frequencies the measured response of the polymer film is selective toward the fastest electrochromic processes in the film, presumably those occurring within the first adsorbed monolayer. Quantitative determination of the electrochromic switching rate, derived from the frequency response of the attenuated reflectivity, shows a linear decrease in the rate, from 11 x 10(3) s(-1) to 3 x 10(3) s(-1), with increasing proportions of PEDTM in the copolymer, suggesting that interactions between the methanol substituent on EDTM and the ITO surface slow the switching process by limiting the rate of conformational change in the polymer film.     

Memcapacitive properties of poly(3,4-ethylenedioxythiophene) modified electrodes

We study the capacitive properties of poly(3,4-ethylenedioxythiophene) (PEDOT) thin layer that shows memory effects. The capacitance vs. charge plot indicates the history-dependence of the electrochemical responses, for instance capacitance with memory or memcapacitance. The variation of the charge vs. potential exhibits a hysteresis loop that is related to the non-equilibrium properties of the redox switching. The calculation of the energy that can be added to and removed from the memcapacitance system during cycling shows a reactive behavior. This property is due to the electromechanical behaviors of PEDOT film that can store and transform electrochemical energy. Indeed, the charging–discharging processes during the redox switching induce a volume and conformational change of the polymer that in turn influences its electrochemical responses. In the context of bio-inspired information processing systems or bio-inspired circuits, a 3-terminal device exhibiting non-linearity and history-dependence responses is of interest for developing organic memory-circuit elements such as an electrochemical memcapacitance.     

Electrochemiluminescence from Ru(bpy)3 immobilized in poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate)-poly(vinyl alcohol) composite films

Electrochemical behavior and electrogenerated chemiluminescence (ECL) of tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) immobilized in poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate)-poly(vinyl alcohol) (PEDOT/PSS-PVA) composite films via ion-exchange have been investigated with tripropylamine (TPA) as the co-reactant at a glassy carbon electrode. The immobilized Ru(bpy)₃²⁺ performed a surface-controlled electrode reaction. The Ru(bpy)₃²⁺ modified electrode showed a fast ECL response to TPA, and was used for the ECL detection of TPA with high sensitivity. The ECL intensity was linearly related to concentrations of TPA over the range from 0.50 μmol L⁻¹ to 0.80 mmol L⁻¹, and the detection limit was 0.10 μmol L⁻¹ (S/N = 3). The as-prepared electrode exhibited good precision and long-term stability for TPA determination.     

Nucleation and growth of poly(3,4-ethylenedioxythiophene) thin films on highly oriented pyrolytic graphite (HOPG) electrodes

The electro-polymerization of 3,4-ethylenedioxythiophene (EDOT) on highly oriented pyrolytic graphite (HOPG) in aqueous media has been investigated by current–time transient measurements and atomic force microscopy. Deposition involved an initial step, in which the whole electrode was essentially covered with an increasing number of nuclei. This first step occurred at very short times (less than 3 ms at high driving force) and was followed by further growth, the nature of which depended on the magnitude of the applied potential. At high driving force, a progressive 3D mechanism took place, while a 2D layer-by-layer process was observed at low driving force. These observations provide a simple means of controlling the morphology of electrodeposited poly(3,4-ethylenedioxythiophene).     

Secondary doping in poly(3,4‐ethylenedioxythiophene):Poly(4‐styrenesulfonate) thin films

The electrical and structural properties of poly(3,4‐ethylenedioxythiophene):poly(4‐styrenesulfonate) (PEDOT:PSS) thin films deposited from aqueous dispersion using different concentrations of selected secondary dopants are studied in detail. An improvement of the electrical conductivity by three orders of magnitude is achieved for dimethyl sulfoxide, sorbitol, ethylene glycol, and N,N‐dimethylformamide, and the secondary dopant concentration dependence of the conductivity exhibits almost identical behavior for all investigated secondary dopants. Detailed analysis of the surface morphology and Raman spectra reveals no presence of the secondary dopant in fabricated films, and thus the dopants are truly causing the secondary doping effect. Although the ratio of benzenoid and quinoid vibrations in Raman spectra is unaffected by doping, the phase transition in PEDOT:PSS films owing to doping is confirmed. Further analysis of temperature‐dependent conductivity reveals 1D variable range hopping (VRH) charge transport for undoped PEDOT:PSS, whereas highly conductive doped PEDOT:PSS films exhibit 3D VRH charge transport. We demonstrate that the charge ‐ hopping dimensionality change should be a fundamental reason for the conductivity enhancement. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1139–1146     

Properties of nanometric and submicrometric multilayered films of poly(3,4-ethylenedioxythiophene) and poly(N-methylpyrrole)

Multilayered films formed by 3, 5 and 7 alternated layers of poly(3,4-ethylenedioxythiophene) and poly(N-methylpyrrole) have been prepared by chronoamperometry under a constant potential of 1.4 V using a layer-by-layer electrodeposition technique. In order to examine influence of the interface:bulk dimensional ratio, the thickness of the yielded films was reduced from the submicrometric to the nanometric scale by decreasing the polymerization time of each layer from 100 s to 10 s. The electroactivity, electrochemical characteristics and morphologies of the resulting multilayered films have been compared with those obtained for both single-component poly(3,4-ethylenedioxythiophene) films prepared using identical experimental conditions and previously reported multilayered films with thickness within the micrometric scale [Estrany F, Aradilla D, Oliver R, Alemán C. Eur Polym J 2007;43:1876].     

Click-functionalization of conducting poly(3,4-ethylenedioxythiophene) (PEDOT)

Efficient post-functionalization of conductive polymer films was achieved by Cu(+)-catalyzed "click"-cycloaddition of novel poly(azidomethyl-EDOT) and various functionalized terminal alkynes under mild heterogeneous conditions with high conversion efficiencies.     

Multicolor and fast electrochromism of nanoporous NiO/poly(3,4-ethylenedioxythiophene) composite thin film

We report a nanoporous NiO/poly(3,4-ethylenedioxythiophene) (PEDOT) composite film using a highly porous NiO film as a template by the combination of chemical bath deposition and electro-polymerization methods. The as-prepared NiO/PEDOT composite film has an interconnecting reticular morphology with nanometer sized pores ranging from 20–150 nm. The NiO/PEDOT composite film exhibits multicolor electrochromism with reversible color changes from purple to light blue brown and presents a transmittance variation of 31% at 600 nm. Fast switching speed is achieved in this composite film, and the response time for oxidation and reduction is 500 and 600 ms, respectively.     

Synthesis and characterization of perfluorohexylated poly(3,4-ethylenedioxythiophene)

The perfluorohexylated 3,4-ethylenedioxythiophene 5 was prepared via Mitsunobu reaction of perfluorohexylatyed diol 2 with diethyl 3,4-dihydroxythiophenedicarboxylate followed by decarboxylation. The polymerization of 5 was conducted with both oxidative chemical and electrochemical polymerizations. The polymers were characterized by cyclic voltammogram, UV, IR, TGA and DSC.     

ESR spectroelectrochemistry of poly(3,4-ethylenedioxythiophene) (PEDOT)

In situ ESR spectroelectrochemical studies of poly(3,4-ethylenedioxythiophene) (PEDOT) have been performed, in an attempt to take a closer look at species responsible for the conductivity of the polymer in the doped state. A series of ESR spectra at progressively changed potentials applied to the polymer film in the oxidation and subsequently, reduction half-cycles were recorded. The results reveal distinct ESR lines with a noteworthy concentration of spins in the reduced state of the polymer and marked changes in both the intensities and ΔB_pp widths of the ESR signal across the studied potential range, indicating non-trivial changes in the character of charge carriers with changing potential. Also, interesting phenomena like the potential hysteresis of the spin concentration and of ΔB_pp linewidths between the oxidation and reduction cycles of the polymer are observed. The presence of residual spins in the polymer in the reduced state may indicate that at least to some partial extent, PEDOT chains exist in the quinoid rather than benzoid configuration in the dedoped state. Hysteresis of spectroscopic parameters may imply that certain hindrance factors like slow anion expulsion speed accompany the dedoping process of the polymer.     

Conductimetric immunosensor based on poly(3,4-ethylenedioxythiophene)

A conductimetric reagentless immunosensor using the biospecific binding pair of goat antirabbit IgG and rabbit IgG has been designed and fabricated using poly (3,4-ethylenedioxythiophene) as the immobilization matrix-cumtransducer.     

Conducting poly(3,4-ethylenedioxythiophene)-montmorillonite exfoliated nanocomposites

Exfoliated nanocomposites formed by poly(3,4-ethylenedioxythiophene) and different concentrations of non-modified montmorillonite (bentonite), which range from 1% to 10% w/w, have been prepared by anodic electropolymerization in aqueous solution. Analyses of the electrochemical and electrical properties reveal that the electroactivity of the nanocomposites is higher than that of the individual homopolymer, while the electrical conductivity of the two systems is practically identical. On the other hand, the exfoliated distribution of the clay in the polymeric matrix and the morphology of the prepared materials have been characterized using transmission electron microscopy, X-ray diffraction and atomic force microscopy. The overall of the results represents a significant improvement with respect to other nanocomposites constituted by conducting polymers and clays, including those involving poly(3,4-ethylenedioxythiophene), and evidences the reliability of the preparation procedure employed in this work.     

Effective charge propagation and storage in hybrid films of tungsten oxide and poly(3,4-ethylenedioxythiophene)

Hybrid (composite) electroactive films consisting of such an organic conducting polymer as poly(3,4-ethylenedioxythiophene), PEDOT, and such a polynuclear inorganic compound as amorphous tungsten oxide, WO₃/H _x WO₃ were fabricated on carbon electrodes through electrodeposition by voltammetric potential in acid solution containing EDOT monomer and sodium tungstate. Electrostatic interactions between the negatively charged tungstic units (existing within WO₃) and the oxidized positively charged conductive polymer (oxidized PEDOT) sites create a robust hybrid structure which cannot be considered as a simple mixture of the organic and inorganic components. It is apparent from scanning electron microscopy that hybrid structures are granular but fairly dense. Because PEDOT and mixed-valence tungsten oxides are electronically conducting, the resulting hybrid films are capable of fast propagation. The reversible and fast redox reactions of tungsten oxide component lie in the potential range where PEDOT matrix is conductive. Furthermore, the hybrid films exhibit good mediating capabilities towards electron transfers between model redox couples such as cationic iron(III,II) and anionic hexacyanoferrate(III,II). Since the films accumulate effectively charge and show high current densities at electrochemical interfaces, they could be of importance to electrocatalysis and to construction of redox capacitors.     

Electrochemical synthesis and surface characterization of poly(3,4-ethylenedioxythiophene) films grown in an ionic liquid

We report a facile method to synthesize poly(3,4-ethylenedioxythiophene) (PEDOT) films at room temperature in a waterproof ionic liquid, 1-ethyl-3-methylimidazolium bis(perfluoroethylsulfonyl)imide (EMIPFSI), by electropolymerization. The ionic liquid leads to the formation of randomly oriented nanofibers and particles confined to submicrometer-sized domains in the film microstructure. X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray (EDX) studies provide information about the intercalation of the cation apart from the reported anion in the polymer film, and on how the imidazolium ion controls the growth of PEDOT nanostructures.