The lipase-catalyzed selective transformation of poly(ε-caprolactone) (PCL) into dicaprolactone (DCL: 1,8-dioxacyclotetradecane-2,9-dione) and the repolymerization of DCL in supercritical carbon dioxide (scCO2) were carried out for the establishment of a sustainable green polymer chemistry for PCL. PCL with a number-average molecular weight of Mn = 110 000 was selectively transformed into repolymerizable cyclic DCL in 90% yield using immobilized Candida antarctica lipase (lipase CA) in scCO2 fluid by compression to 18 MPa in the presence of a small amount of water at 40 °C. The DCL obtained such was readily polymerized by lipase CA in scCO2 to produce a PCL with an Mn of 33 000 after 6 h.
Concept of sustainable chemical recycling of PCL using an enzyme. 相似文献
PCL microspheres featuring a macroporous morphology and a bone‐bioactive surface have been prepared. ‘Camphene’ was introduced to generate pores within the microsphere network. The pore size was variable from a few to tens to hundreds of µm depending on the Camphene/PCL ratio. Macropores (with sizes >50 µm) could be obtained with a Camphene/PCL ratio exceeding 6. The microsphere surface was further tailored with apatite mineral phase through solution‐mediated precipitation, to endow the interface with bone bioactivity. Rat bone marrow stromal cells attached and spread actively on microspheres and populated well within their macropores. The developed microspheres may be potentially applicable as a cell delivery scaffold for bone tissue engineering.
A new concept to build shape memory polymers (SMP) combining outstanding fixity and recovery ratios (both above 99% after only one training cycle) typical of chemically crosslinked SMPs with reprocessability restricted to physically crosslinked SMPs is demonstrated by covalently bonding, through thermoreversible Diels–Alder (DA) adducts, star‐shaped poly(ε‐caprolactones) (PCL) end‐functionalized by furan and maleimide moieties. A PCL network is easily prepared by melt‐blending complementary end‐functional star polymers in retro DA regime, then by curing at lower temperature to favour the DA cycloaddition. Such covalent network can be reprocessed when heated again at the retro DA temperature. The resulting SMP shows still excellent shape memory properties attesting for its good recyclability.
Tough networks are prepared by photo‐crosslinking high‐molecular‐weight DLLA and TMC macromers. These amorphous networks exhibit tunable thermal and mechanical properties and have excellent shape‐memory features. Variation of the monomer ratio allows adjustment of Tg between approximately ?13 and +51 °C. The elastic moduli at room temperature can be varied between 4.5 and 2730 MPa. The crosslinks allow the networks to return to their original shape after deformation. 60:40 DLLA:TMC networks have Tg values between room temperature and body temperature, with mechanical properties at body temperature close to soft tissues. Several medical devices are prepared from these networks.
A hybrid technology that combines a three‐dimensional (3‐D) dispensing system with an electrospinning process was used to produce a hierarchical 3‐D scaffold consisting of micro‐sized polycaprolactone (PCL) strands and micro/nano‐sized fibres. The micro/nanofibre biocomposites electrospun with PCL/small intestine submucosa (SIS) and PCL/Silk fibroin were layered between melt‐plotted micro‐strands. The scaffold containing SIS exhibited a stronger hydrophilic property than other scaffolds due to the various hydrophilic components in SIS. The 3‐D hierarchical scaffold having biocomposites exhibited an incredibly enhanced initial cell attachment and proliferation of bone marrow‐derived mesenchymal stem cells relative to the normally designed 3‐D scaffold.
Well‐defined amphiphilic block‐graft copolymers PCL‐b‐[DTC‐co‐(MTC‐mPEG)] with polyethylene glycol methyl ether pendant chains were designed and synthesized. First, monohydroxyl‐terminated macroinitiators PCL‐OH were prepared. Then, ring‐opening copolymerization of 2,2‐dimethyltrimethylene carbonate (DTC) and cyclic carbonate‐terminated PEG (MTC‐mPEG) macromonomer was carried out in the presence of the macroinitiator in bulk to give the target copolymers. All the polymers were characterized by 1H NMR and gel permeation chromatography (GPC). The polymers have unimodal molecular weight distributions and moderate polydispersity indexes. The amphiphilic block‐graft copolymers self‐assemble in water forming stable micelle solutions with a narrow size distribution.
The monomer 3‐ethyl‐1‐vinyl‐2‐pyrrolidone ( 3 ) and the homopolymer poly(3‐ethyl‐1‐vinyl‐2‐pyrrolidone) ( 5 ) have been synthesized. Polymer 5 is soluble in water and shows a critical temperature (Tc) of 27 °C. The presence of cyclodextrin causes a slight shift of the Tc. The lower critical solution temperature (LCST) could be varied between 27 and 40 °C by copolymerization with N‐vinyl‐2‐pyrrolidone. A linear correlation between the Tc and the copolymer composition is observed.
Summary: This work reports a new type of poly(ε‐caprolactone) (PCL) robust hollow sphere with controllable biodegradability, produced by grafting PCL shells from the surface of silica sphere cores and removing the template cores. Bis(ε‐caprolactone‐4‐yl) (BCY) composed of two ε‐caprolactone molecules was used as the crosslinker, which not only greatly strengthened the PCL hollow spheres but also brought hardly any non‐biodegradable component into the system. Solubility experiments and biodegradation tests show that the crosslinked PCL hollow spheres were robust both in water and acetone, and were completely biodegradable with characteristics of controllable biodegradability according to the content of the BCY. The Rhodamine release test indicated that the release rate of encapsulated drugs in the PCL hollow spheres was controlled by diffusion and the biodegradability of the PCL molecules, and the latter mechanism will dominate when more enzymes are involved.
Reaction scheme for synthesis of linear and crosslinked hollow poly(ε‐caprolactone) spheres. 相似文献
The preparation of novel highly water‐soluble electrostatic complexes from C60‐anchored multi‐armed poly(acrylic acid)s and cationic porphyrin derivatives was demonstrated. The UV‐vis absorption and photoluminescence (PL) of these complexes show that the absorption of soret band exhibits a remarkable red shift and the emission of the Q band indicates an apparent quenching effect in comparison with that of the parent cationic porphyrin. These results imply a remarkable ground state and excited state interaction between the porphyrin ring and the C60 moiety.
Bis(2,2′:6′,2″‐terpyrid‐4′‐yl) diethylene glycol was synthesized as a monomer unit and further utilized for polymerization with FeCl2 in order to form water‐soluble coordination polymers. Viscosity measurements and film‐forming properties indicate the formation of linear coordination polymers or larger ring structures. The terpyridine/iron(II) complexes are stable up to temperatures of 210 °C, but can be uncomplexed by the addition of an excess of a strong competitive ligand (HEDTA) under mild conditions.
A compositional graded film of poly(ε‐caprolactone) (PCL) with 4,4′‐thiodiphenol (TDP), in the film thickness direction, was fabricated by self‐diffusing of TDP in the PCL melt. We found out the self‐bending deformation of the gradient film, which bent into a rolled‐up shape by itself. The initial shape of the film was flat when the sample was quenched from the melt. Upon the fast crystallization of PCL, the gradient film bent to the side with low TDP content. Then, after PCL crystallized the film bent to the opposite direction, that is, to the side with high TDP content. This bending to the TDP rich region was induced by not only the crystallization of PCL but also mass transfer due to the diffusion of TDP from TDP rich region to poor region.
An aqueous solution of a poly(ethylene glycol)‐polycaprolactone‐poly(ethylene glycol) (PEG‐PCL‐PEG) with a composition of EG13CL23EG13 undergoes multiple transitions, from sol‐to‐gel (hard gel)‐to‐sol‐to‐gel (soft gel)‐to‐sol, in the concentration range 20.0∼35.0 wt.‐%. Through dynamic mechanical analysis, UV‐vis spectrophotometry, small angle X‐ray scattering, differential scanning calorimetry, microcalorimetry and 13C NMR spectroscopy, the mechanism of these transitions was investigated. The hard gel and soft gel are distinguished by the crystalline and amorphous state of the PCL. The extent of PEG dehydration and the molecular motion of each block also played a critical role in the multiple transitions. This paper suggests a new mechanism for these multiple transitions driven by temperature changes.
Bimodal fiber meshes with fiber diameters differing by one order of magnitude, are electrospun in a simple one‐step process, using a standard single syringe electrospin setup. The nano‐ and microfiber meshes combine the benefits of nanofibers (cell adhesion, proliferation) with those of microfibers (open structure, large pore size) and are therefore interesting as scaffolds for cellular infiltration.
