Binary Reactive/Inert Non‐Fouling Polymeric Surfaces

Binary reactive/inert antifouling polymer brushes were grafted via a two step surface initiated polymerization from printed initiator monolayer and provided robust, effective polymeric surfaces for bioattachment with distinguishably reduced non‐specific adsorption. This synthetic strategy can be harnessed to build complex binary polymeric structures on substrate surfaces and the polymer brush surfaces reported in the present paper can be widely used for versatile biological study.

     

Reversibly Switchable Double‐Responsive Block Copolymer Brushes

Poly(2‐hydroxyethyl methacrylate)‐block‐poly(N‐isopropylacrylamide) (PHEMA‐b‐PNIPAM) was prepared by controlled surface‐initiated ATRP from silicon substrates, and the resulting block copolymers were successfully converted into the corresponding PSEMA‐b‐PNIPAM by esterification of the hydroxy groups on the PHEMA block using excess of succinic anhydride. The PSEMA‐b‐PNIPAM block copolymer brushes respond to both temperature and pH stimuli. The double‐responsive behavior of the block copolymer brushes in solution was investigated by height imaging and force–distance measurements of AFM. The results clearly show the responsive behavior of the smart block copolymer brushes.

     

N‐(2‐Hydroxypropyl)methacrylamide (HPMA) Copolymer‐Linked Nitroxides: Potential Magnetic Resonance Contrast Agents

N‐(2‐Hydroxypropyl)methacrylamide (HPMA) copolymer‐linked nitroxides were synthesized as macromolecular contrast agents for MR imaging. Molar relaxivities of HPMA copolymer‐linked nitroxides increased linearly in proportion to the number of nitroxides attached per gram of copolymer. HPMA copolymer‐linked nitroxides with 15, 20 and 30 mol‐% nitroxide exhibited higher relaxivities than gadolinium diethylenetriaminepentaacetic acid (Gd‐DTPA). These results demonstrate the potential of HPMA copolymer‐linked nitroxides as MR contrast agents for solid tumors.

Structure of HPMA copolymer‐linked nitroxides.     

A Versatile and Efficient Hydrosilylation Route to Functionalized Polyferrocenylsilanes

Summary: The synthesis of a series of polyferrocenylsilanes (PFSs) containing CC functionalities in the side‐group structure and their subsequent derivatization by hydrosilylation chemistry are described. Hydrosilylation is shown to be an effective postpolymerization functionalization method, particularly in the case of poly(ferrocenylmethylvinylsilane), which can be prepared by photolytic anionic ring‐opening polymerization of the corresponding ferrocenophane monomer.

     

Surfaces Resistant to Fouling from Biological Fluids: Towards Bioactive Surfaces for Real Applications

The fouling from four human body fluids – blood plasma, cerebrospinal fluid, urine and saliva – and four animal fluids – foetal bovine and calf sera, egg and milk – relevant to human and veterinary medicine, immunology, biology and diagnostics is assessed on antifouling SAMs and on polymer brushes of oligo(ethylene glycol) methacrylate, 2‐hydroxyethyl methacrylate, carboxybetaine acrylamide and N‐(2‐hydroxypropyl)methacrylamide synthesized via ATRP. While important deposits from the all biofluids are observed on SAMs, a superior resistance is achieved on polymer brushes. Importantly, only poly(CBAA) and poly(HPMA) are capable of resisting the fouling from the most challenging media, blood plasma and eggs.

     

A Facile Route to Synthesize Highly Uniform Nanocapsules: Use of Amphiphilic Poly(acrylic acid)‐block‐polystyrene RAFT Agents to Interfacially Confine Miniemulsion Polymerization

Miniemulsion polymerization with an amphiphilic poly(acrylic acid)‐block‐polystyrene reversible addition–fragmentation chain transfer agent as a surfactant and polymerization mediator is used to synthesize highly uniform nanocapsules. The nanocapsules with uniform structures, which include particle size, shell thickness, and shape symmetry, could be achieved by the post‐addition of a small amount of sodium dodecyl sulfate. Although the solid particles seem unavoidable, the ‘pure’ uniform core–shell structures are easily collected by centrifugation.

     

Following Polymer Brush Growth Using the Quartz Crystal Microbalance Technique

Summary: The growth of surface‐initiated poly([2‐(methacryloyloxy)ethyl]trimethylammonium chloride) (pMETAC) brushes by ATRP was monitored by the quartz crystal microbalance technique with dissipation (QCM‐D). The change in mass of the quartz crystals starting from the adsorption of a thiol initiator monolayer through to the growth of the polymer brushes was determined. The use of QCM‐D allowed determination of the kinetics of polymerization from the surface. The technique can be applied to other polymers synthesised from surfaces and allows the study of varying conditions on the polymerization kinetics.

Changes in frequency of a quartz crystal during polymerization.     

Are the Interactions between Recombinant Prion Proteins and Polymeric Surfaces Related to the Hydrophilic/Hydrophobic Balance?

New non‐fouling tubes are developed and their influence on the adhesion of neuroproteins is studied. Recombinant prion proteins are considered as a single component representative of hydrophobic proteins. Samples are stored for 24 h at 4 °C in tubes coated with two different coatings: poly(N‐isopropylacrylamide) as a hydrophilic surface and a plasma‐fluorinated coating as a hydrophobic one. The protein adhesion is monitored by ELISA tests, XPS and confocal microscopy. It appears that the highest recovery of recombinant prion protein in the liquid phase is obtained with the hydrophilic surface while the hydrophobic character of the storage tube induces an important amount of biological loss. However, the recovery is not complete even for tubes coated with poly(N‐isopropylacrylamide).

     

Holes and Ledges Created by Multilayer Assembly on Polyelectrolyte Brushes: A Novel Route for the Three‐Dimensional Nanoscale Design of Surfaces

The layer‐by‐layer (LBL) assembly of poly(diallyldimethylammonium chloride) and poly(sodium styrene sulfonate) on poly(sulfo propyl methacrylate) brushes resulted in films with nanometer‐ and micrometer‐sized holes and ledges, observed by atomic force microscopy and scanning electron microscopy. Polyelectrolyte assembly was followed by the quartz microbalance technique. The formation of ledges and holes is explained by the interaction of the brush polymers with the incoming polyelectrolytes during the LBL assembly, inducing a spatially localized and self‐organized accumulation of the assembled polymers.

     

Microparticle‐Supported Conjugated Polyelectrolyte Brushes Prepared by Surface‐Initiated Kumada Catalyst Transfer Polycondensation for Sensor Applications

A ‘grafting‐from’ approach to synthesize microparticle‐supported conjugated polyelectrolyte brushes is presented. Poly(3‐bromohexylthiophene) is selectively grown from monodisperse organosilica microparticles by surface‐initiated Kumada catalyst‐transfer polycondensation (SI‐KCTP) and then ionizable amino groups are introduced by a two‐step polymer analogous transformation. Optical properties of the resulting microparticle‐supported conjugated polyelectrolyte brushes were found to be dependent on the surrounding chemical environment and thus the particles are promising materials for sensor applications.

     

Three‐dimensional Arrangement of Short DNA Oligonucleotides at Surfaces via the Synthesis of DNA‐branched Polyacrylamide Brushes by SI‐ATRP

Short DNA oligonucleotide branches are incorporated into acrylamide brushes via surface initiated atom transfer radical polymerization in an attempt to increase DNA surface density by building three‐dimensional molecular architectures. ATR‐FTIR as well as hybridization studies followed by SPR confirm the incorporation of the DNA sequences into the polymer backbone. MALDI‐TOF analysis further suggests that six acrylamide monomer units are typically separating DNA branches present on a single brushes approximately 26 units long. This new approach offers a promising alternative to SAM‐based nucleic acid and aptamer sensors and could enable the realization of more complex soft materials of controlled architecture capable of both recognition and signaling by including additional optically or electrochemically active moieties.

     

Synthesis of Amphiphilic ABC Triblock Copolymers with PEO as the Middle Block

Summary: Stepwise anionic polymerization, catalytic hydrogenation, and atom transfer radical polymerization were performed to synthesize an amphiphilic ABC triblock copolymer, poly(ethylene‐alt‐propylene)‐block‐poly(ethylene oxide)‐block‐poly(hexyl methacrylate) (PEP‐b‐PEO‐b‐PHMA), with hydrophilic PEO as the middle block. The resulting block copolymers have well‐defined molecular weights and narrow molecular weight distributions as revealed by ¹H NMR spectroscopy and gel permeation chromatography.

GPC chromatograms of an ABC triblock copolymer, PEP‐b‐PEO‐b‐PHMA, and its intermediate precursors exhibiting narrow polydispersities.     

Microwave‐Assisted Ring‐Opening Polymerization of ε‐Caprolactone in the Presence of Ionic Liquid

Summary: Microwave‐assisted ring‐opening polymerization of ε‐caprolactone in the presence of 1‐butyl‐3‐methylimidazolium tetrafluoroborate ionic liquid using zinc oxide as a catalyst is investigated. By adding 30 wt.‐% ionic liquid, poly(ε‐caprolactone) with a weight‐average molar mass of 28 500 g · mol⁻¹ is obtained at 85 W for 30 min. The results indicate that the polymerization could be efficiently enhanced in the presence of ionic liquids under microwave irradiation because ionic liquids can effectively absorb microwave energy.

     

Temperature‐Responsive Glycopolymer Brushes Synthesized via RAFT Polymerization Using the Z‐group Approach

Summary: Stimuli‐responsive glycopolymer brushes composed of N‐acryloyl glucosamine (AGA) and N‐isopropylacrylamide (NIPAAm) were prepared using RAFT polymerization. The RAFT agent was immobilized on the surface of a treated silicon waver via covalent attachment using the Z‐group. PAGA and PNIPAAm brushes showed a linear increase in brush thickness with the consumption of monomer in solution. The polymers generated in solution confirm the living behavior with the molecular weight increasing linearly with monomer conversion while the molecular weight distribution remains narrow. Additionally, the ability of PAGA brushes to grow further in the presence of NIPAAm reveals the presence of an active RAFT end group indicative of a living system. PAGA and PNIPAAm homopolymer brushes up to 30 nm were grown using this technique. PAGA brushes were utilized for further chain extension to generate stimuli‐responsive brushes with block structures of PAGA and PNIPAAm. The PAGA‐block‐PNIPAAm brushes were found to grow in size with the consumption of NIPAAm. Contact angle measurements confirm the suggested mechanism showing that the second monomer is incorporated between the first layer and the silicon surface as expected using the Z‐group approach.

Structure of the stimuli‐responsive glycopolymer brushes.     

Polymer‐Based Rectifying Diodes on a Glass Substrate Fabricated by Ink‐Jet Printing

Summary: The fabrication of polymer diodes on a glass substrate by an ink‐jet printing technique is reported. Both an n‐type semiconductive polymer, poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐(1‐cyanovinylene)phenylene] (CN‐PPV), and a p‐type semiconductive polymer, polypyrrole (PPy) or poly(3,4‐ethylenedioxythiophene) (PEDOT), were printed through a piezoelectric ink‐jet printer. The printed CN‐PPV/PPy and CN‐PPV/PEDOT diodes showed good rectifying characteristics. These results indicate the potential of the low‐cost ink‐jet printing technique to produce polymer microelectronic devices and circuits.

Schematic diagram of the printed polymer diode     

Novel Amphiphilic Degradable Poly(ε‐caprolactone)‐graft‐poly(4‐vinyl pyridine), Poly(ε‐caprolactone)‐graft‐poly(dimethylaminoethyl methacrylate) and Water‐Soluble Derivatives

New amphiphilic graft copolymers that have a poly(ε‐caprolactone) (PCL) biodegradable hydrophobic backbone and poly(4‐vinylpyridine) (P4VP) or poly(2‐(N,N‐dimethylamino)ethyl methacrylate) (PDMAEMA) hydrophilic side chains have been prepared by anionic polymerization of the corresponding 4VP and DMAEMA monomers using a PCL‐based macropolycarbanion as initiator. The water solubility of these amphiphilic copolymers is improved by quaternization, which leads to fully water‐soluble cationic copolymers that give micellar aggregates in deionized water with diameters ranging from 65 to 125 nm. In addition, to improve the hydrophilicity of PCL‐g‐P4VP, grafting of poly(ethylene glycol) (PEG) segments has been carried out to give a water‐soluble double grafted PCL‐g‐(P4VP;PEG) terpolymer.

     

Encapsulation of Bovine Serum Albumin in Temperature‐Programmed “Shell‐in‐Shell” Structures

A novel approach to load a hydrophilic bovine serum albumin into drug carriers was proposed in terms of temperature‐programmed “shell‐in‐shell” structures, which were fabricated with poly(N‐isopropylacrylamide), poly(lactide), poly(ethylene glycol), and Au nanoparticles. Spherically well‐defined “shell‐in‐shell” structures were constructed by a modified‐double‐emulsion method (MDEM). The lower critical solubility temperature of the structures was manipulated to 36.4 °C which was confirmed by UV/Vis spectroscopy and DSC (Differential Scanning Calorimetry).

TEM image of the Au@PLLA‐PEG@PNIPAAm‐PDLA structure.     

Nanoreactor‐Assisted Polymerization Toward Stable Dispersions of Conductive Composite Particles

We demonstrate the functioning of a macromolecular nanoreactor which guides a reaction in a confined volume and leads toward improved functional properties of a product material. In our approach, the polymerization of aniline (ANi) is conducted within the interfacial volume of spherical polyelectrolyte brushes (SPB) which are densely affixed to colloidal particles. The SPB provide optimal conditions for matrix polymerization by the efficient confinement of ANi monomers within the finite volume of polyelectrolyte brushes and controlled delivery of the oxidizing reagent to the reaction volume. The excellent kinetic stability of the resulting core–shell particles together with the high macroscopic conductivity of the respective composite open up perspectives for novel materials (a conductive ink).

     

Recyclable Spherical Polyelectrolyte Brushes Containing Magnetic Nanoparticles in Core

Spherical polyelectrolyte brushes consisting of a magnetite/polystyrene nanocomposite core and a poly(acrylic acid) brush shell were prepared by photo‐emulsion polymerization. They are narrowly dispersed, superparamagnetic and redispersible after aggregating by external magnetic field, as determined by transmission electron microscopy, dynamic light scattering, thermal gravimetric analysis and a vibrating sample magnetometer. Magnetic control is thus introduced into nano‐sized spherical polyelectrolyte brushes to achieve recovery and controllable delivery in applications. This approach opens up the way for cost‐effective applications of spherical polyelectrolyte brushes.

     

Low‐Temperature Growth of Thick Polystyrene Brushes via ATRP

Summary: This contribution describes the graft polymerization of polystyrene (PS) by atom transfer radical polymerization at 50, 60, and 75 °C. Thick PS brushes were grown from initiator‐functionalized PGMA layers on silicon, and constant growth rates provide indirect evidence that the polymerizations were controlled.

Formation of polystyrene brushes at T < T_g by ATRP of styrene from α‐bromoester initiator‐functionalized poly(glycidyl methacrylate) layers.