Preparation and certification of a reference material for the determination of nutrients in seawater

There is an urgent need for natural water reference materials certified for nutrients. In 1996, NRC collected seawater for a proposed CRM at a depth of 200 m in the North Atlantic; this was immediately filtered through 0.05-m cartridge filters into 50-L carboys. The water was later homogenized in the NRC laboratories in Ottawa and stabilized via gamma irradiation. Over six years of stability testing no significant deterioration was detected. In addition to the usual customary standard colorimetric procedures, alternative analytical methods were developed to enable the certification process. The production of a CRM called MOOS-1 will be discussed. Certified values, with uncertainty components addressing the homogeneity, stability, and characterization of the material, were calculated to be: orthophosphate=1.56±0.07 µmol L^–1, silicate=26.0±1.0 µmol L^–1, nitrite=3.06±0.15 µmol L^–1, and nitrite and nitrate=23.7±0.9 µmol L^–1.     

Detection of 2,4,6-trichloroanisole in chlorinated water at nanogram per litre levels by SPME–GC–ECD

A method involving solid-phase micro extraction (SPME) and gas chromatography with electron capture detection (SPME–GC–ECD) has been optimised for identification and quantification of 2,4,6-trichloroanisole (TCA) at ng L^–1 concentrations in disinfected (chlorinated) water samples. A central composite design was used for factorial analysis of four factors, three factors related to the SPME (PDMS fibre) procedure (adsorption time, temperature of the sample during headspace sampling, and desorption time) and one related to the GC operation (the rate of increase of the temperature of the GC oven). Good linearity (linear correlation coefficient greater than 0.999) was observed for TCA concentrations up to 50 ng L^–1, limits of detection and quantification of 0.7 and 2.3 ng L^–1, respectively, and good precision (relative standard deviation 2.8% and 3.4% for 5 and 30 ng L^–1 of TCA, respectively). Besides TCA, this system also enables the detection and quantification of the four trihalomethanes in the g L^–1 concentration range with limits of detection and quantification of approximately 0.3 g L^–1 and 1 g L^–1, respectively.     

A rapid and sensitive GC–MS method for determination of 1,3-dichloro-2-propanol in water

A rapid analytical method for sensitive determination of 1,3-dichloro-2-propanol (1,3-DCP) in river water has been developed. 1,3-DCP is extracted from water with ethyl acetate. After filtration through sodium sulfate the ethyl acetate phase is analyzed by gas chromatography–mass spectrometry. The method uses 1,3-DCP-d₅ as internal standard. Different extraction solvents, concentrations of ammonium sulfate in the water samples, and the effect of humic acid were tested and their influence on the recovery of DCP has been evaluated. The method quantification limit was 0.1 g L^–1. For spiked water samples (0–5.2 g L^–1, n=21) a repeatability coefficient of variation of 5.4% was obtained. The average recovery rate of 1,3-DCP was 105±3% (n=21). Stability tests, which were carried out with Danube river water, led to an estimated 1,3-DCP degradation rate of 0.008±0.0008 day^–1 at 6°C.     

Rapid multi-element analysis of groundwater by high-resolution inductively coupled plasma mass spectrometry

A rapid and sensitive method was developed to determine, with a single dilution, the concentration of 33 major and trace elements (Na, Mg, Si, K, Ca, Li, Al, P, S, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Sr, Mo, Cd, In, Sn, Sb, Cs, Ba, Re, Hg, Pb, Bi, U) in groundwater. The method relies on high-resolution inductively coupled plasma mass spectrometry (HR ICP-MS) and works across nine orders of magnitude of concentrations. For most elements, detection limits for this method are considerably lower than methods based on quadrupole ICP-MS. Precision was within or close to ±3% (1) for all elements analyzed, with the exception of Se (±10%) and Al (±6%). The usefulness of the method is demonstrated with a set of 629 groundwater samples collected from tube wells in Bangladesh (Northeast Araiharzar). The results show that a majority of tube well samples in this area exceed the WHO guideline for As of 10 g L^–1, and that those As-safe wells frequently do not meet the guideline for Mn of 500 µg L^–1 and U of 2 µg L^–1.     

Detection of ethanol in human body fluids by headspace solid-phase micro extraction (SPME)/capillary gas chromatography

Summary Ethanol has been found extractable from human whole blood and urine samples by headspace solid-phase micro extraction (SPME) with a Carbowax/divinylbenzene-coated fiber. After heating a vial containing the body fluid sample with ethanol, and isobutanol as internal standard (IS) at 70°C in the presence of (NH₄)₂SO₄, a Carbowax/divinylbenzene-coated SPME fiber was exposed in the headspace of the vial to allow adsorption of the compounds. The fiber needle was then injected into a middle-bore capillary gas chromatography (GC) port. The headspace SPME-GC gave intense peaks for both compounds; a small amount of background noises appeared, but did not interfere with the detection of the compounds. Recoveries of ethanol and IS were 0.049 and 0.026% for whole blood, respectively, and 0.054 and 0.085% for urine, respectively. The calibration curves for ethanol showed excellent linearity in the range of 80–5000 mg L^–1 for whole blood and 40–5000 mg L^–1 for urine; the detection limits for both samples were 20 and 10 mg L^–1, respectively. The data on actual determination of ethanol after the drinking of beer are also presented for two subjects.     

Comparison of Different Sorbents for Solid-Phase Extraction of Phenoxyalkanoic Acid Herbicides

An HPLC procedure for determination of phenoxyalkanoic acid herbicides in water samples is proposed. The analytical column Phenomenex C18(2) Luna 5 µm and UV detection at 225 nm were applied. Baseline resolution was achieved in isocratic mode with a mobile phase consisting of acetonitrile/acetic acid (40/60, v/v), adjusted to pH 2.5. SPE sorbents – C₁₈ BondElut, phenyl-silica, LiChrolut SAX and polymeric sorbents – were compared for isolation and preconcentration of 6 phenoxyalkanoic acid herbicides. Higher (above 95%) and more reproducible recoveries were obtained with polymeric and phenyl-silica sorbents using pure methanol for elution. The method was tested for river water samples with the limit of detection in the range of 2–3 µg L⁻¹ (for 50 mL sample) and a reproducibility of 5% RSD.     

Determination of oxaliplatin in human plasma and plasma ultrafiltrate by graphite-furnace atomic-absorption spectrometry

A method for sensitive determination of the anti-cancer agent oxaliplatin in human plasma and human plasma ultrafiltrate (pUF) is presented. The method is based on the quantification of platinum by graphite-furnace atomic-absorption spectrometry, with Zeeman correction and an atomisation temperature of 2,700°C. Sample pretreatment involves dilution of the samples with a solution containing 0.15 mol L^–1 NaCl and 0.20 mol L^–1 HCl in water. Validation was performed in accordance with the most recent FDA guidelines for bioanalytical method validation. All results were within requirements. The validated ranges of quantification were 0.10–400 mol L^–1 for human pUF and 0.50–400 mol L^–1 for plasma. The assay is now successfully used to support pharmacokinetic studies of cancer patients treated with oxaliplatin.     

A rapid HPLC method for the determination of carboxylic acids in human urine using a monolithic column

A rapid HPLC method for the determination of carboxylic acids in urine samples using a Chromolith Performance RP/18e 100/4.6 with Chromolith Guard Cartridge RP/18e 10/4.6 (Merck KgaA, Darmstadt, Germany) was developed. The method facilitates the simultaneous determination of aromatic hydrocarbon metabolites mandelic acid (MA) and phenylglyoxylic acid (PGA) from styrene and ethylbenzene, hippuric acid (HA) from toluene and 2-, 3-, 4-methylhippuric acids (MHA) from xylene. 3-Hydroxybenzoic acid (3-HBA) was used as internal standard. A chromatographic run is completed within less than 5 min for styrene, ethylbenzene and toluene metabolites, and within 10 min for xylene metabolites. The detection limits are 9 mg L^–1 urine for MA, 1.25 mg L^–1 urine for PGA, 4.9 mg L^–1 urine for HA, 22 mg L^–1 urine for 2-MHA, and 18.5 mg L^–1 urine for 3-MHA.No significant differences of the MA, PGA and HA concentrations in human urine samples obtained by HPLC chromatography on LiChrosorb RP 18 and on Chromolith RP/18e columns were found. The results were evaluated by using ANOVA.Abbreviations MA mandelic acid - PGA phenylglyoxylic acid - HA hippuric acid - MHA methylhippuric acid - 3-HBA 3-hydroxybenzoic acid - ANOVA analyses of variance - GC gas chromatography - HPLC high-performance liquid chromatography     

Comparison of GC-ICP-MS and HPLC-ICP-MS for species-specific isotope dilution analysis of tributyltin in sediment after accelerated solvent extraction

This study describes a direct comparison of GC and HPLC hyphenated to ICP–MS determination of tributyltin (TBT) in sediment by species-specific isotope dilution analysis (SS-IDMS). The certified reference sediment PACS-2 (NRC, Canada) and a candidate reference sediment (P-18/HIPA-1) were extracted using an accelerated solvent extraction (ASE) procedure. For comparison of GC and LC methods an older bottle of PACS-2 was used, whilst a fresh bottle was taken for demonstration of the accuracy of the methods. The data obtained show good agreement between both methods for both the PACS-2 sediment (LC–ICP–IDMS 828±87 ng g^–1 TBT as Sn, GC–ICP–IDMS 848±39 ng g^–1 TBT as Sn) and the P-18/ HIPA-1 sediment (LC–ICP–IDMS 78.0±9.7 ng g^–1 TBT as Sn, GC–ICP–IDMS 79.2±3.8 ng g^–1 TBT as Sn). The analysis by GC–ICP–IDMS offers a greater signal-to-noise ratio and hence a superior detection limit of 0.03 pg TBT as Sn, in the sediment extracts compared to HPLC–ICP–IDMS (3 pg TBT as Sn). A comparison of the uncertainties associated with both methods indicates superior precision of the GC approach. This is related to the better reproducibility of the peak integration, which affects the isotope ratio measurements used for IDMS. The accuracy of the ASE method combined with HPLC–ICP–IDMS was demonstrated during the international interlaboratory comparison P-18 organised by the Comité Consultatif pour la Quantité de Matière (CCQM). The results obtained by GC–ICP–IDMS for a newly opened bottle of PACS-2 were 1087±77 ng g^–1 Sn for DBT and 876±51 ng g^–1 Sn for TBT (expanded uncertainties with a coverage factor of 2), which are in good agreement with the certified values of 1090±150 ng g^–1 Sn and 980±130 ng g^–1 Sn, respectively.     

Silver nanoparticle assemblies supported on glassy-carbon electrodes for the electro-analytical detection of hydrogen peroxide

Electrochemical detection of hydrogen peroxide using an edge-plane pyrolytic-graphite electrode (EPPG), a glassy carbon (GC) electrode, and a silver nanoparticle-modified GC electrode is reported. It is shown, in phosphate buffer (0.05 mol L^–1, pH 7.4), that hydrogen peroxide cannot be detected directly on either the EPPG or GC electrodes. However, reduction can be facilitated by modification of the glassy-carbon surface with nanosized silver assemblies. The optimum conditions for modification of the GC electrode with silver nanoparticles were found to be deposition for 1 min at –0.5 V vs. Ag from 5 mmol L^–1 AgNO₃/0.1 mol L^–1 TBAP/MeCN, followed by stripping for 2 min at +0.5 V vs. Ag in the same solution. A wave, due to the reduction of hydrogen peroxide on the silver nanoparticles is observed at –0.68 V vs. SCE. The limit of detection for this modified nanosilver electrode was 2.0×10^–6 mol L^–1 for hydrogen peroxide in phosphate buffer (0.05 mol L^–1, pH 7.4) with a sensitivity which is five times higher than that observed at a silver macro-electrode. Also observed is a shoulder on the voltammetric wave corresponding to the reduction of oxygen, which is produced by silver-catalysed chemical decomposition of hydrogen peroxide to water and oxygen then oxygen reduction at the surface of the glassy-carbon electrode.     

Development of new rat monoclonal antibodies with different selectivities and sensitivities for 2,4,6-trinitrotoluene (TNT) and other nitroaromatic compounds

Five new rat monoclonal antibodies (mAbs) for 2,4,6-trinitrotoluene (TNT) and other nitroaromatic compounds, including, especially, the metabolite 2-amino-4,6-dinitrotoluene (2-ADNT), are described. Five heterogeneous, competitive enzyme-linked immunosorbent assays (ELISAs) were developed. Assay 1 uses mAb DNT4 3F6 as recognition element and gives a standard curve for TNT in 40 mmol L^–1 phosphate buffered saline (PBS) with a test midpoint (IC₅₀) of 0.26±0.08 g L^–1 (n=20). Assay 2 (mAb DNT4 4G4) has an IC₅₀ of 0.35±0.07 g L^–1 (n=18), assay 3 (mAb DNT4 1A3) has an IC₅₀ of 0.73±0.14 g L^–1 (n=15), and assay 4 (mAb DNT4 1A7) has an IC₅₀ of 2.32±0.70 g L^–1 (n=15). Assay 5 (mAb DNT2 4B4) is very selective for 2-ADNT and has an IC₅₀ of 8.5±1.7 g L^–1 (n=15) in PBS. These antibodies for nitroaromatic compounds differ not only in their sensitivity but also in their selectivity. Major cross-reactants are 1,3,5-trinitrobenzene, 2-ADNT, 4-amino-2,6-dinitrotoluene (4-ADNT), 2,4-dinitroaniline, 3,5-dinitroaniline, and 2,6-dinitroaniline. Although assay 5 is not highly sensitive, the mAb DNT2 4B4 in this assay is highly selective for 2-ADNT. Of all the compounds tested, only 2,4-dinitroaniline and 3,5-dinitroaniline had relevant cross reactivities, 18% and about 26%, respectively. Two ELISAs, using mAbs DNT4 3F6 and DNT2 4B4, were used to analyze different concentrations of TNT and 2-ADNT, respectively, in three different surface water matrices (river and lake water). Both assays were affected by the matrix, but usually performed well (recovery within the range 70–120%). In addition, these ELISAs were used to analyze mixtures of TNT, 2-ADNT, and 4-ADNT, at three different concentrations, in the same water matrices. A different recognition pattern was clearly visible with both assays and depended on the cross reactivities of the corresponding mAb.Dedicated to the memory of Wilhelm Fresenius     

Certification of mono-, di-, and tributyltin compounds in marine sediment certified reference material by species-specific isotope dilution mass spectrometric analysis using synthesized <Superscript>118</Superscript>Sn-labeled butyltins

A new marine sediment reference material (NMIJ CRM 7301-a) for butyltins analysis was prepared and certified by the National Metrological Institute of Japan, National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). The original material of the sediment was collected at a bay near industrial activities in Japan. The sediment material was air-dried, sieved, homogenized, and packaged into 1,000 glass bottles (60 g each). Certification of NMIJ CRM 7301-a was carried out at NMIJ using two different types of species-specific isotope dilution mass spectrometry: isotope dilution–ethylation–gas chromatography/inductively coupled plasma mass spectrometry (GC/ICPMS) and isotope dilution–ethylation–gas chromatography/mass spectrometry (GC/MS). A mixture of ¹¹⁸Sn-enriched monobutyltin, dibutyltin, and tributyltin was synthesized in our laboratory and was used as a spike for both techniques. Certified values are given for tributyltin (0.044±0.004 mg kg^–1 as Sn), dibutyltin (0.056±0.006 mg kg^–1 as Sn, and monobutyltin (0.058±0.013 mg kg^–1 as Sn), being at lower levels than currently available sediment CRMs for the analysis of organotins.     

Chromotropic acid,a fluorogenic chelating agent for aluminium(III)

Complexation of aluminium(III) with the fluorogenic ligand chromotropic acid (4,5-dihydroxynaphthalene-2,7-disulfonic acid) has been revisited with the aim of using enhancement of the fluorescence intensity as an analytical tool. Complexation at the optimum pH4 was shown to lead to a 1:1 complex with a stability constant log ₁₁₀=18.4±0.7. The fluorogenic effect was thoroughly investigated. Nearly selective excitation of the chelate rather than the ligand could be achieved at wavelengths longer than 360 nm. For analytical purposes the main interfering ion was Ga³⁺. The strongest competing ligand was shown to be citric acid. Competitive complexation by acetate or formate ions can also make their use in a buffer at the usual concentration, 0.2 mol L^–1, questionable, whereas a 10^–2 mol L^–1 formic acid buffer was shown to be a good alternative. The calibration plot showed that the dependence of response on Al(III) concentration was linear up to 500 g L^–1; the detection limit was 0.65 g L^–1 (3SD _blank, n=10, SD=±1.4% at 10 g L^–1 and ±0.8% at 100 g L^–1). The analytical procedure was successfully applied to several samples of tap water and the results were in good agreement with those from AAS determination.     

Determination of thiol compounds in rat striatum microdialysate by HPLC with a nanosized CoHCF-modified electrode

A cobalt hexacyanoferrate (CoHCF) nanoparticle (size ca. 60 nm) chemically modified electrode (CME) was fabricated and the electrochemical behavior of thiols at this nanosized CoHCF CME was studied. In comparison with a bare glassy carbon (GC) electrode and with a general CoHCF CME which was electrodeposited in the traditional manner, the present nanosized CoHCF CME efficiently performed electrocatalytic oxidation for glutathione (GSH) and L-Cysteine (L-Cys) with relatively high sensitivity, outstanding stability, and long-life. Combined with high-performance liquid chromatography (HPLC), the nanosized CoHCF CME was used for electrochemical determination (ECD) of GSH and L-Cys. The peak currents were a linear function of concentrations in the range 2.0×10^–7 to 2.0×10^–4 mol L^–1 for both GSH and L-Cys, with detection limits of 1.2×10^–7 and 1.0×10^–7 mol L^–1, respectively. Coupled with microdialysis sampling, the HPLC–ECD system has been successfully used to assess the GSH and L-Cys content of rat striatum.     

Determination of octylphenol and nonylphenol in aqueous sample using simultaneous derivatization and dispersive liquid–liquid microextraction followed by gas chromatography–mass spectrometry

A simple and fast sample preparation method for the determination of nonylphenol (NP) and octylphenol (OP) in aqueous samples by simultaneous derivatization and dispersive liquid–liquid microextraction (DLLME) was investigated using gas chromatography–mass spectrometry (GC/MS). In this method, a combined dispersant/derivatization catalyst (methanol/pyridine mixture) was firstly added to an aqueous sample, following which a derivatization reagent/extraction solvent (methyl chloroformate/chloroform) was rapidly injected to combine in situ derivatization and extraction in a single step. After centrifuging, the sedimented phase containing the analytes was injected into the GC port by autosampler for analysis. Several parameters, such as extraction solvent, dispersant solvent, amount of derivatization reagent, derivatization and extraction time, pH, and ionic strength were optimized to obtain higher sensitivity for the detection of NP and OP. Under the optimized conditions, good linearity was observed in the range of 0.1–1000 μg L⁻¹ and 0.01–100 μg L⁻¹ with the limits of detection (LOD) of 0.03 μg L⁻¹ and 0.002 μg L⁻¹ for NP and OP, respectively. Water samples collected from the Pearl River were analyzed with the proposed method, the concentrations of NP and OP were found to be 2.40 ± 0.16 μg L⁻¹ and 0.037 ± 0.001 μg L⁻¹, respectively. The relative recoveries of the water samples spiked with different concentrations of NP and OP were in the range of 88.3–106.7%. Compared with SPME and SPE, the proposed method can be successfully applied to the rapid and convenient determination of NP and OP in aqueous samples.     

In-field determination of nanomolar nitrite in seawater using a sequential injection technique combined with solid phase enrichment and colorimetric detection

A novel sequential injection method for the determination of nitrite at nanomolar level in seawater samples has been developed. The pink azo compound was formed based on the Griess reaction and quantitatively adsorbed onto a Sep-Pak C18 cartridge. The enriched azo compound was rinsed with water and ethanol (28%, v/v) in turn, and then eluted with an eluent containing 26.6% (v/v) ethanol and 0.108 mol L⁻¹ H₂SO₄. Finally the azo compound was measured using a spectrophotometer at 543 nm. Under the optimized conditions, the linear calibration ranges were 0.71–42.9 nmol L⁻¹ for a 150-mL sample and 35.7–429 nmol L⁻¹ for a 15-mL sample. The relative standard deviation of 8 measurements was 1.44% for 14.3 nmol L⁻¹ nitrite. For the 150 mL sample, the detection limit was estimated to be 0.1 nmol L⁻¹. The throughput of the method was about 4 samples per hour. The proposed method has been successfully applied to the in-field determination of nanomolar concentrations of nitrite in seawater.     

Simultaneous Determination of Trimethoprim, Sulfadiazine, Florfenicol and Oxolinic Acid in Surface Water by Liquid Chromatography Tandem Mass Spectrometry

A liquid chromatographic/tandem mass spectrometric method using atmospheric pressure chemical ionisation (LC-APCI-MS-MS) was developed for simultaneous determination of trimethoprim, sulfadiazine, florfenicol and oxolinic acid in surface water. The compounds were extracted by solid phase extraction on a polymeric sorbent. Two transition products were monitored for each compound. The detection capabilities related to the transition products of lowest abundance were 1 ng L^–1 for trimethoprim, sulfadiazine and florfenicol and 2 ng L^–1 for oxolinic acid. The mean recoveries were 84%, 83%, 96% and 78% at a level of 10 ng L^–1. The relative repeatability standard deviations were less than 11% at a level of 10 ng L^–1.     

Rapid analysis of pyrethroids in whole urine by high-performance liquid chromatography using a monolithic column and off-line preconcentration in a restricted access material cartridge

A rapid high-performance liquid chromatography (HPLC) method using a monolithic column with UV detection at 238 nm was developed for the determination of fenpropathrin, betacyfluthrin, deltamethrin, and permethrin (cis and trans isomers) in whole urine. The method is based on the use of a monolithic chromatographic column and a restricted access material (RAM) cartridge for sample preparation. The mobile phase was water/acetonitrile (42:58 v/v), the flow rate was 3 mL min^–1, and chromatographic separation was carried out in 10 min. The separation of cis and trans isomers of permethrin was also possible under the above-mentioned conditions. Detection limits in reconstituted whole urine samples were between 0.9 g L^–1 for betacyfluthrin and 4.4 g L^–1 for fenpropathrin and trans-permethrin. Recoveries for urine samples spiked with different amounts of pyrethroids (between 19 g L^–1 and 75 g L^–1) were in the 70±6 to 90±7% range.     

Development of a stir-bar-sorptive extraction–liquid desorption–large-volume injection capillary gas chromatographic–mass spectrometric method for pyrethroid pesticides in water samples

Stir-bar-sorptive extraction followed by liquid desorption and large-volume injection capillary gas chromatography with mass spectrometric detection (SBSE–LD–LVI-GC–MS), had been applied for the determination of ultra-traces of eight pyrethroid pesticides (acrinathrin, cypermethrin, deltamethrin, esfenvalerate, fenpropathrin, fenvalerate, and permethrin cis and trans isomers) in water samples. Instrumental calibration for selected-ion monitoring acquisition and conditions that could affect the SBSE–LD efficiency are fully discussed. By performing systematic assays on 30-mL water samples spiked at the 0.10 g L^–1 level it was established that stir-bars coated with 47 L polydimethylsiloxane, an equilibrium time of 60 min (750 rpm), 5% methanol as organic modifier, and acetonitrile as back-extraction solvent, provided the best analytical performance to monitor pyrethroid pesticides in water matrices. Good accuracy (81.8–105.0%) and remarkable reproducibility (<11.7%) were obtained, and the experimental recovery data were in good agreement with the theoretical equilibrium described by octanol–water partition coefficients (log K_O/W), with the exception of acrinathrin for which lower yields were measured. Excellent linear dynamic ranges between 25 and 400 ng L^–1 (r²>0.994), low quantification (3.0–7.5 ng L^–1) and detection (1.0–2.5 ng L^–1) limits were also achieved for the eight pyrethroid pesticides studied. The method was successfully used for analysis of tapwater and groundwater matrices spiked at the 0.10 g L^–1, revealing the suitability of the method for determination of pyrethroid pesticides in real samples. The method was shown be reliable and sensitive and a small volume of sample was required to monitor pyrethroids at ultra-trace levels, in compliance with international regulatory directives on water quality.     

Transport properties and electroanalytical response characteristics of drotaverine ion-selective sensors

The construction and electroanalytical response characteristics of poly(vinyl chloride) matrix ion-selective sensors (ISSs) for drotaverine hydrochloride are described. The membranes incorporate ion-association complexes of drotaverine with tetraphenylborate, picrate, tetraiodomercurate, tetraiodobismuthate, Reinecke salt, and heteropolycompounds of Keggin structure—molybdophosphoric acid, tungstophosphoric acid, molybdosiliconic acid and tungstosiliconic acid as electroactive materials for ionometric sensor controls. These ISSs have a linear response to drotaverine hydrochloride over the range 8×10^–6 to 5×10^–2 mol L^–1 with cationic slopes from 51 to 58 mV per concentration decade. These ISSs have a fast response time (up to 1 min), a low determination limit (down to 4.3×10^–6 mol L^–1), good stability (3–5 weeks), and reasonable selectivity. Permeabilities and ion fluxes through a membrane were calculated for major and interfering ions. Dependences of the transport properties of the membranes on the concentrations of the ion exchanger and near-membrane solution and their electrochemical characteristics are presented. The ISSs were used for direct potentiometry and potentiometric titration (sodium tetraphenylborate) of drotaverine hydrochloride. Results with mean accuracy of 99.1±1.0% of nominal were obtained which corresponded well to data obtained by use of high-performance liquid chromatography.