钙钛矿型LaxSr1－xNi1－yCoyO3光电催化活性研究

用甘氨酸-硝酸盐燃烧合成法, 制备La_xSr_1－xNi_1－yCo_yO₃复合氧化物的陶瓷粉末, 对钙钛矿氧化物进行了XRD结构分析. 在通氧或不通氧下测试氧还原和氧析出的循环伏安曲线. 结果表明: 该氧电极具有双功能催化特性, 但不完全可逆. 利用汞灯作为激发光源, 进行几种水溶性染料和五种混合染料光解实验, 利用紫外-可见、红外以及人工神经网络光度法研究La_xSr_1－xNi_1－yCo_yO₃的催化性能. 结果表明: La_xSr_1－xNi_1－yCo_yO₃ (x＝0.7, 0.9, 1; y＝0.3, 0.75)复合氧化物都具有较强光催化特性; La_xSr_1－xNi_1－yCo_yO₃的光催化活性高于La_xSr_1－xNiO₃, 这与B位离子(Ni^2—, Co^2－)的电子构型有关; Co^2＋的加入可使La_xSr_1－xNiO₃的光催化活性有所提高.     

空气中合成固溶体荧光粉Ba2(Zn, Mg)Si2O7:Ce3+,Eu2+,Eu3+及其发光特性

采用高温固相法在空气中合成了Ba_1.97-yZn_1-xMg_xSi₂O₇:0.03Eu,yCe³⁺系列荧光粉。分别采用X-射线衍射和荧光光谱对所合成荧光粉的物相和发光性质进行了表征。在紫外光330~360 nm激发下,固溶体荧光粉Ba_1.97-yZn_1-xMg_xSi₂O₇:0.03Eu的发射光谱在350~725 nm范围内呈现多谱峰发射,360和500 nm处有强的宽带发射属于Eu²⁺离子的4f⁶5d¹-4f⁷跃迁,590~725 nm红光区窄带谱源于Eu³⁺的⁵D₀-⁷F_J (J=1,2,3,4)跃迁,这表明,在空气气氛中,部分Eu³⁺在Ba_1.97-yZn_1-xMg_xSi₂O₇基质中被还原成了Eu²⁺;当x=0.1时,荧光粉Ba_1.97Zn_0.9Mg_0.1Si₂O₇:0.03Eu的绿色发光最强,表明Eu³⁺被还原成Eu²⁺离子的程度最大。当共掺入Ce³⁺离子后,形成Ba_1.97-yZn_0.9Mg_0.1Si₂O₇:0.03Eu,yCe³⁺荧光粉体系,其发光随着Ce³⁺离子浓度的增大由蓝绿区经白光区到达橙红区;发现名义组成为Ba_1.96Zn_0.9Mg_0.1Si₂O₇:0.01Ce³⁺,0.03Eu的荧光粉的色坐标为(0.323,0.311),接近理想白光,是一种有潜在应用价值的白光荧光粉。讨论了稀土离子在Ba₂Zn_0.9Mg_0.1Si₂O₇基质中的能量传递与发光机理。     

CeCl3-CdCl2-H2O和CeCl3-CdCl2-HCl-H2O的相平衡

测定了三元系CeCl₃-CdCl₂-H₂O (25 ℃)和四元系CeCl₃-CdCl₂-HCl(～8.4％)-H₂O(25 ℃) 的相平衡溶度数据,绘制了相应的溶度图.该三元系是由5个固相区CdCl₂&;#8226;2.5H₂O(原始盐)、CdCl₂&;#8226;H₂O(原始盐)、6CdCl₂&;#8226;CeCl₃&;#8226;14H₂O、4CdCl₂&;#8226;CeCl₃&;#8226;12H₂O、CeCl₃&;#8226;7H₂O(原始盐)组成的复杂体系.该四元系是由5个固相区CdCl₂&;#8226;H₂O(原始盐)、9CdCl₂&;#8226;CeCl₃&;#8226;19H₂O、6CdCl₂&;#8226;CeCl₃&;#8226;14H₂O、4CdCl₂&;#8226;CeCl₃&;#8226;12H₂O、CeCl₃&;#8226;7H₂O(原始盐)组成的复杂体系.其中6CdCl₂&;#8226;CeCl₃&;#8226;14H₂O在该三元系是介稳化合物.9CdCl₂&;#8226;CeCl₃&;#8226;19H₂O 、6CdCl₂&;#8226;CeCl₃&;#8226;14H₂O和4CdCl₂&;#8226;CeCl₃&;#8226;12H₂O用X射线粉末衍射及TG-DTG和DSC等方法进行了研究,并对X射线粉末衍射进行了指标化.     

纳米钙钛矿LaxSr1-xFe1-yCoyO3复合氧化物的制备和表征

用甘氨酸-硝酸盐燃烧合成法，制备La_xSr_1-xFe_1-yCo_yO₃复合氧化物的陶瓷粉末，对该钙钛矿型氧化物进行了XRD、IR、紫外漫反射光谱及循环伏安曲线分析。结果表明：该复合氧化物粉体平均晶粒为15.3～29.8 nm,为立方和正交晶系。该氧电极具有双功能催化特性，但不完全可逆。对水溶液染料进行光解实验，利用紫外-可见、人工神经网络光度法研究La_xSr_1-xFe_1-yCo_yO₃的催化性能。结果表明：CO²⁺的加入可使La_xSr_1-xFeO₃的光催化活性有所提高，B位离子(Fe³⁺，CO²⁺)改变与加入，使La_xSr_1-xFe_1-yCo_yO₃(x=0.7，0.3；y=0.3，0.9，1)光催化活性高于La_xSr_1-xFeO₃。同时，对5种染料进行紫外光解，在0.75 h，脱色率大于91%，并为动力学一级反应。     

层状O2结构锂锰氧化物Li0.60[MgxCoyMn1-x-y]O2的制备及结构表征

本文采用离子交换法分别制备了双复合锂锰氧化物Li_0.60[Mg_xMn_1-x]O₂(0.05 ≤ x ≤ 0.15)和三复合锂锰氧化物Li_0.60[Mg_xCo_yMn_1-x-y]O₂(x=0.05，0.05 ≤      

La-Ce对PbTiO3陶瓷气相扩渗生成La2Ti6O15CeTi21O38的陶瓷材料及其电性能

报道了采用气相法对PbTiO₃陶瓷扩渗La-Ce混合稀土元素的研究. 在气相扩渗过程中, La, Ce与PbTiO₃陶瓷组元发生了复杂反应,生成了稀土化合物La₂Ti₆O₁₅和CeTi₂₁O₃₈, 制备出未见报道的La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃陶瓷材料, 经测试其导电性能发生了十分显著的变化. La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃陶瓷材料的室温电阻率从2.0 ×10¹⁰ W·m下降为0.248 W·m,而且随着温度的变化, 晶粒电阻呈现明显的PTCR效应,而晶界电阻随着温度的升高,呈急剧连续降低状态,总电阻的变化规律与晶界电阻的变化相一致, 试样总电阻的PTCR效应已不存在, 近趋导体. 经XPS测试分析, 进一步证实了La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃陶瓷材料中铅、钛等元素均有变价, 因而导致了La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃陶瓷材料电阻率的降低, 测试结果还首次给出了La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃陶瓷材料中各元素结合能位置的峰值. TG-DTA热分析表明La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃陶瓷材料具有较好的高温热稳定性.     

o-ZrW1.6Mo0.4O8·H2O正交相的合成与表征

The precursor ZrW_1.6Mo_0.4O₇(OH)₂(H₂O)₂ was characterized by IR and XRD methods. δ′-ZrW_1.6Mo_0.4O₈ was prepared by careful controlling the annealing conditions from the precursor and was determined to have the formula as o-ZrW_1.6Mo_0.4O₈·H₂O by TG-DSC, IR, and XRD methods. The relation between o-ZrW_1.6Mo_0.4O₈·H₂O and o-ZrW_1.6Mo_0.4O₈ was discussed through variable temperature XRD patterns. Further more, the mechanism of the precursor dehydration was suggested.     

298.15 K Li2B4O7-MgCl2-H2O体系热力学性质的电动势法测定及离子相互作用模型的研究

测定了298.15 K下, 无液接电池Li-ISE│Li₂B₄O₇ (m_A)(aq.), MgCl₂(m_B)(aq.)│AgCl/Ag的电动势, 利用测定结果计算了Li₂B₄O₇-MgCl₂-H₂O体系离子强度在0.05～3 mol•kg^－1范围内, 不同MgCl₂离子强度分数的溶液中LiCl的平均活度系数, 并给出了其随离子强度I, B₄O₇^2－和Mg^2＋浓度的变化规律. 结合以往关于该体系和Li₂B₄O₇-LiCl-H₂O, Li₂B₄O₇-H₂O体系的等压研究结果, 用迭代和多元线性回归方法对Li^＋-Mg^2＋-Cl^－-B₄O₇^2－-H₂O体系的离子相互作用模型进行了研究. 具体方法为考虑了该体系在不同的总硼浓度范围H₃BO₃, B(OH)₄^－, B₃O₃(OH)₄^－和B₄O₅(OH)₄^2－四种含硼化合物的存在以及各硼化合物间的化学平衡, 以修正了的Pitzer渗透系数方程和活度系数方程为基础, 对该体系的等压法和电动势法研究结果进行最小二乘拟合, 拟合的标准偏差为0.0167, 用该模型计算的该体系的渗透系数、活度系数与实验值基本一致.     

Bi2WO6量子点(QDs)修饰Bi2MoO6-xF2x异质结的构筑及其催化活性增强机理

采用简单沉积-沉淀法合成了Bi₂WO₆@Bi₂MoO_6-xF_2x（BWO/BMO6-xF2x）异质结,借助XRD、XPS、TEM、SEM、EDS、UV-Vis-DRS、PC和EIS等测试技术对其组成、形貌、光吸收特性和光电化学性能等进行系统表征,并以模型污染物罗丹明B（RhB）的光催化降解作为探针反应来评价Bi₂WO₆@Bi₂MoO_6-xF_2x异质结的光催化活性增强机制。形貌分析表明,所得Bi₂MoO₆微球由大量厚度为20~50 nm的纳米片组成;FE-SEM和HR-TEM分析表明,尺寸约为10 nm的Bi₂WO₆量子点均匀沉积在Bi₂MoO_6-xF_2x微球表面,形成新颖的Bi₂WO₆@Bi₂MoO_6-xF_2x异质结;与纯Bi₂MoO₆或者Bi₂WO₆相比,1∶1Bi₂WO₆@Bi₂MoO_6-xF_2x异质结表现出更好的光催化活性和光电流性质,其对RhB光催化降解的表观速率常数分别为纯BMO和BWO的6.4和11.6倍。PC和EIS图谱分析表明,Bi₂WO₆量子点表面沉积显著提高Bi₂MoO_6-xF_2x光生电子/空穴的分离效率和迁移速率;活性物种捕获实验证明了·O₂^-和h⁺是主要的活性物种。根据实验结果,探讨了F^-掺杂和Bi₂WO₆量子点之间的协同效应对Bi₂MoO₆的光催化活性的影响机制。     

由大环配体[As4W40O140]28-与NiII形成的新型超大杂多化合物

在pH = 4.0的水溶液中, NiCl₂·6H₂O, NH₄Cl与Na₂₇[NaAs₄W₄₀O₁₄₀]·60H₂O反应, 得到了新的杂多砷钨酸盐(NH₄)₂₀[Na₂(H₂O)₂Ni(H₂O)₅{Ni(H₂O)}₂As₄W₄₀O₁₄₀]·61H₂O单晶, 用X射线单晶衍射法及元素分析确定了其结构, 晶体属三斜晶系, P¹空间群; 其晶胞参数为: a = 1.33135(18), b = 1.9722(3), c = 3.6430(5) nm, α = 78.010(2)°, β = 82.145(2)°, γ = 74.385(2)°, V = 8.978(2) nm3, Z = 2, R1 = 0.0512, wR2 = 0.0684 (I > 2σ). 在聚阴离子[Na₂(H₂O)₂Ni(H₂O)₅{Ni(H₂O)}₂As₄W₄₀O₁₄₀]^20-中, 2个Ni²⁺和2个Na⁺分占大环配体[As₄W₄₀O₁₄₀]^28-内的4个S2空位, 每个S2位提供4个O_d向金属离子配位, 2个Ni²⁺的配位数为6, 两个Na⁺的配位数分别为5和6, 另一个Ni²⁺处于环外, 与[As₄W₄₀O₁₄₀]^28-的一个端基氧(O_d)桥连成键, 其配位数为6.     

Extraction and separation studies of uranium/VI/with tris-/2-ethyl hexyl/phosphate

A solvent extraction method is proposed for the extraction and separation of uranium from salicylate media using tris-/2-ethyl hexyl/ phosphate dissolved in xylene as an extractant. The optimum conditions were evaluated from a critical study of pH, salicylate concentration, extractant concentration, period of equilibration and diluent. The method permits the separation of uranium from thorium, cerium, titanium, zirconium, hafnium, copper, vanadium and chromium from binary mixtures and is applicable to the analysis of uranium in synthetic samples. The method is precise, accurate, fast and selective.     

Phase equilibria in a system of aqueous arginine with an octane solution of sulfonic acid

The extraction of arginine (Arg) from aqueous salt (0.1 M NaCl) solutions with a sulfo extractant in a wide range of pH values and amino acid concentrations was studied. The 0.1 M solution of dinonylnaphthalenesulfonic acid (HD) in octane was used as an extractant. The degree of extraction was found to be high at pH 0.8–9.0. This can be explained by the effect of additional intermolecular interactions in the extractant phase involving the guanidine group of Arg.     

Solvent extraction of cadmium as a previous step for its determination in biological samples by electrothermal atomization atomic absorption spectrometry

A method is proposed for the solvent extraction of cadmium using 1,5-bis(di-2-pyridylmethylene)thiocarbohydrazide (DPTH) as extractant. The optimum extraction conditions were evaluated from a critical study of the effect of pH, concentration of extractant, shaking time and ionic strength. The maximum volume ratio of the aqueous to organic phase was 30:1 for a single-stage extraction of99-100% of the metal ion. The detection limit is 0.01 ng/ml cadmium, and the calibration is linear from 0.1 to 5 ng/ml. The relative standard deviation for 10 replicate measurements is 1.8% for 2 ng/ml cadmium. The extraction method was applied to the determination of cadmium in some biological materials using graphite furnace atomic absorption spectrometry.     

Liquid-liquid distribution studies of thorium salicylate with tris-(2-ethylhexyl)phosphate

A method is proposed for the extraction of thorium(IV) from salicylate media using tris-(2-ethylhexyl)phosphate dissolved in toluene as an extractant. The optimum conditions were evaluated from a critical study of pH, salicylate concentration, extractant concentration, period of equilibration and diluent. The method permits the separation of thorium from the associated elements and is applicable to the analysis of monazite sand. The method is precise, accurate, fast and selective.     

缺氧沉积物中重金属形态连续萃取方法的稳定性研究

考察了海水养殖区域缺氧沉积物中重金属形态连续萃取法萃取过程中溶液pH值、温度变化和胶体形成对形态分离结果的影响。结果表明,连续萃取法Step1萃取酸溶态时,萃取液pH值的轻微升高使Pb和Zn的萃取结果明显降低;Step2萃取还原态时,萃取液pH值明显升高对重金属的萃取结果影响很小;Step3萃取有机质结合态时,萃取液pH值的降低对重金属萃取结果影响较小(除Pb外)。由于连续萃取法中各步萃取反应的热力学过程不同,Step1和Step2萃取后溶液温度轻微升高而在Step3中溶液温度稍微降低,溶液温度变化(<2.5℃)对重金属形态的影响很小。在Step1、Step2和Step4萃取过程中胶体的形成和存在,对萃取液Cd、Zn和Cu有明显的吸附影响;而在Step3萃取中萃取剂的分散作用有效控制了溶液中胶体的形成。因此采用连续萃取方法评价沉积物中的重金属形态时,控制萃取液pH值和胶体形成有利于提高萃取结果的稳定性和准确性。     

Separation of Uranium(VI) by Extraction with Dibutylditiophosphoric Acid

The extraction of uranium(VI) from aqueous solutions with dibutylditiophosphoric acid in organic solvents was studied. The influence of different factors as pH of the aqueous phase, extractant concentration and nature of solvent was investigated in order to find the optimum conditions for separation of metal from aqueous nitrate solutions. The effect of neutral donor extractants was also searched and the efficiency of the extraction was calculated.     

Poly(cyclotriphosphazene-co-phloroglucinol)PCPP as a solid phase extractant for preconcentrative separation of uranium(VI) from aqueous solution

Poly(cyclotriphosphazene-co-phloroglucinol) (PCPP) microspheres, a new solid phase extraction for extracting uranium(VI), synthesized via one-pot precipitation copolymerization. The PCPP microspheres were characterized by FT-IR, SEM/EDS, zeta potential and N₂ adsorption/desorption isotherms. Through the extraction experiment to evaluate the extraction behavior of the PCPP microspheres for uranium(VI). The extractant can achieve the optimal effect under the conditions of contact time with 60 min, pH = 3.5, initial concentration 100 mg L⁻¹ and extractant dosage 0.70 g L⁻¹. The extraction behavior obeyed with the pseudo second-order model and Langmuir isotherm model.

     

磷酸三丁酯/正辛醇络合萃取对氯苯酚

以对氯苯酚稀溶液为研究对象,以正辛醇为稀释剂,研究了萃取剂种类及其浓度、水相平衡pH、对氯苯酚初始浓度等因素对萃取分配比的影响,并用NaOH对其负载溶质的有机相进行反萃.结果表明,络合萃取对处理高浓度对氯苯酚废水具有优势;磷酸三丁酯(TBP)的浓度和体系的pH是影响络合萃取的关键因素;采用NaOH对有机相进行反萃,当NaOH浓度为0.5mol/L时反萃率达到98.55%.红外光谱分析表明,TBP萃取对氯苯酚基于氢键作用机理.     

微波萃取花生壳天然黄色素及其稳定性研究

对福建产花生壳进行了微波萃取天然黄色素及其稳定性的研究 .研究表明微波萃取的工艺条件是 :以pH =3,体积分数 70 %的乙醇水溶液作提取剂 ,原料与提取剂配比为 1g∶5mL ,微波辐射功率为 12 0W ,辐射时间2 4 0s.对该色素稳定性研究结果表明 ,该色素为水溶性色素 ,属黄酮类色素 ,适用pH值范围比较宽 ,尤其碱性状态效果最佳 ,对光、热稳定性好 ,大多数食品添加剂对色素稳定性影响不大 ,对氧化剂H2 O2 的耐受能力较差 ,对还原剂Na2 SO3 的耐受能力强     

Development of a Liquid‐liquid Extraction System for Rhodium(III) by 2‐octylaminopyridine from Weak Malonate Media

We have developed the extraction method of rhodium(III) from malonate media with 2‐octylaminopyridine (2‐OAP) in xylene at pH 8.0. The quantitative extraction of rhodium(III) with extractant was found by screening of different physicochemical parameters like malonate concentration, extractant concentration, pH, diluents, effect of temperature, aq: org phase ratio, loading capacity of 2‐OAP. The optimum condition was malonate=0.025 M, pH=8.0, 2‐OAP=0.05 M in xylene. The complete stripping of rhodium(III) from the loaded organic phase was carried out with 2 M HCl. Log‐log plot was investigated to determine the stoichiometry of the extracted species and it was found to be 1 : 2 : 1 (metal : acid :extractant). The versatility of the proposed method was checked for extraction and separation of rhodium(III) from binary, ternary mixture of associated metal ions as well as platinum group metals and from the synthetic solution of rhodium minerals and alloys.