Study on morphology and photoluminescence of Au/SiO2 nanocomposite films

Au/SiO₂ nanocomposite films were fabricated on Si (111) substrates by radio frequency (RF) magnetron sputtering technique and annealing at different temperature for 20 min (mode A) and at 1000 °C for different annealing time (mode B). The nanocomposite films were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and photoluminescence (PL). SEM results demonstrate that the size of Au crystallites in mode A first increases and then decreases, on increasing annealing temperature, according to the results of XRD spectra. Analysis of PL spectra in mode B shows that the intensity of the emission peak at 440 nm and 523 nm early increases and late decreases, with increasing annealing time at 1000 °C. The origin of the emission peak at around 440 nm was related to the size and quantity of Au particles and one of the emission peak at around 523 nm was related to the nanostructure of films in agreement with SEM imagines. Experimental results indicated that morphology, microstructure and luminescence of Au/SiO₂ nanocomposite films showed close affinity with annealing temperature and annealing time.     

Electroluminescence from Si／SiO2 films deposited on p—Si substrates

The structure of Au/Si/SiO₂/p-Si has been fabricated using the magnetron sputtering technique. It has a very good rectifying behaviour. Visible electroluminescence (EL) has been observed from the Au/Si/SiO₂/p-Si structure at a forward bias of 5V or larger. A broad band with one peak around 650－660 nm appears in all the EL spectra of the structure. The effects of the thickness of the Si layer in the Si/SiO₂ films and of the input electrical power on EL spectra are studied systematically.     

XPS investigation of diffusion of two-layer ZrO2/SiO2 and SiO2/ZrO2 sol–gel films

Two-layer ZrO₂/SiO₂ and SiO₂/ZrO₂ films were deposited on K9 glass substrates by sol–gel dip coating method. X-ray photoelectron spectroscopy (XPS) technique was used to investigate the diffusion of ZrO₂/SiO₂ and SiO₂/ZrO₂ films. To explain the difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films, porous ratio and surface morphology of monolayer SiO₂ and ZrO₂ films were analyzed by using ellipsometry and atomic force microscopy (AFM). We found that for the ZrO₂/SiO₂ films there was a diffusion layer with a certain thickness and the atomic concentrations of Si and Zr changed rapidly; for the SiO₂/ZrO₂ films, the atomic concentrations of Si and Zr changed relatively slowly, and the ZrO₂ layer had diffused through the entire SiO₂ layer. The difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films was influenced by the microstructure of SiO₂ and ZrO₂.     

Fabrication and characterization of Au/SiO2 nanocomposite films grown by radio-frequency cosputtering

Au/SiO₂ nanocomposite films were prepared on Si wafers by cosputtering of SiO₂ and gold wires. Au/Si atomic ratios in Au/SiO₂ nanocomposite films were varied from 0.53 to 0.92 by controlling the length of gold wire to study the evolution of the crystallization of gold, the size of Au/SiO₂ nanocomposite particles, and the optical properties of as-deposited Au/SiO₂ nanocomposite films. An X-ray photoelectron spectroscopy reveals that Au exists as a metallic phase in the bulk of SiO₂ matrix. Dome-shaped Au/SiO₂ nanocomposite particles and both Au (1 1 1) and (2 0 0) planes were observed in a field-emission scanning electron microscopy and X-ray diffraction studies respectively. With an ultraviolet-visible, absorption peaks of Au/SiO₂ nanocomposite films were observed at 525 nm.     

Enhanced nonlinear optical absorption of Au/SiO2 nano-composite thin films

Nano metal-particle dispersed glasses are the attractive candidates for nonlinear optical material applications.Au/SiO 2 nano-composite thin films with 3 vol% to 65 vol% Au are prepared by inductively coupled plasma sputtering.Au particles as perfect spheres with diameters between 10 nm and 30 nm are uniformly dispersed in the SiO 2 matrix.Optical absorption peaks due to the surface plasmon resonance of Au particles are observed.The absorption property is enhanced with the increase of Au content,showing a maximum value in the films with 37 vol% Au.The absorption curves of the Au/SiO 2 thin films with 3 vol% to 37 vol% Au accord well with the theoretical optical absorption spectra obtained from Mie resonance theory.Increasing Au content over 37 vol% results in the partial connection of Au particles,whereby the intensity of the absorption peak is weakened and ultimately replaced by the optical absorption of the bulk.The band gap decreases with Au content increasing from 3 vol% to 37 vol % but increases as Au content further increases.     

Preparation and characterization of novel Pd/SiO2 and Ca-Pd/SiO2 egg-shell catalysts with porous hollow silica

Novel egg-shell structured monometallic Pd/SiO₂ and bimetallic Ca-Pd/SiO₂ catalysts were prepared by an impregnation method using porous hollow silica (PHS) as the support and PdCl₂ and Ca(NO₃)₂·4H₂O as the precursors. It was found from transmission electron microscope (TEM), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) that Pd was loaded on PHS with a particle size of 5-12 nm in Pd/SiO₂ samples and the Pd particle size in Ca-Pd/SiO₂ was smaller than that in Pd/SiO₂ since Ca could prevent Pd particles from aggregating. X-ray photoelectron spectroscopy (XPS) analyses exhibited that Pd 3d_5/2 binding energies of Pd/SiO₂ and Ca-Pd/SiO₂ were 0.2 and 0.9 eV lower than that of bulk Pd, respectively, as a result of the shift of the electron cloud from Pd to oxygen in Pd/SiO₂ and to both oxygen and Ca in Ca-Pd/SiO₂. The activity of Ca-Pd/SiO₂ egg-shell catalyst for CO hydrogenation and the selectivity to methanol, with a value of 36.50 mmol_CO mol⁻¹_Pd s⁻¹ and 100%, respectively, were much higher than those of the catalysts prepared with traditional silica gel as the support, owing to the porous core-shell structure of the PHS support.     

Au/SiO2纳米多层薄膜的制备及其性质表征

利用多靶磁控溅射技术制备了Au/SiO₂纳米颗粒分散氧化物多层复合薄膜.研究了在保持Au单层颗粒膜沉积时间一定时薄膜厚度一定、变化SiO₂的沉积时间及SiO₂的沉积时间一定而改变薄膜厚度时，多层薄膜在薄膜厚度方向的微观结构对吸收光谱的影响.研究结果表明：具有纳米层状结构的Au/SiO₂多层薄膜在560 nm波长附近有明显的表面等离子共振吸收峰，吸收峰的强度随Au颗粒的浓度增加而增强，在Au颗粒浓度相同的情况下，复合薄膜 关键词： 2纳米复合薄膜')" href="#">Au/SiO₂纳米复合薄膜 多靶磁控溅射 吸收光谱 有效介质理论     

Nanostructuring Si surface and Si/SiO2 interface using porous-alumina-on-Si template technology. Electrical characterization of Si/SiO2 interface

In this work, anodic porous alumina thin films with pores in the nanometer range are grown on silicon by electrochemistry and are used as masking material for the nanopatterning of the silicon substrate. The pore diameter and density are controlled by the electrochemical process. Through the pores of the alumina film chemical oxidation of the silicon substrate is performed, leading to the formation of regular arrays of well-separated stoichiometric silicon dioxide nanodots on silicon, with a density following the alumina pores density and a diameter adjustable by adjusting the chemical oxidation time. The alumina film is dissolved chemically after the SiO₂ nanodots growth, revealing the arrays of silicon dioxide dots on silicon. In a next step, the nanodots are also removed, leaving a nanopatterned bare silicon surface with regular arrays of nanopits at the footprint of each nanodot. This silicon surface structuring finds interesting applications in nanoelectronics. One such application is in silicon nanocrystals memories, where the structuring of the oxidized silicon surface leads to the growth of discrete silicon nanocrystals of uniform size. In this work, we examine the electrical quality of the Si/SiO₂ interface of a nanostructured oxidized silicon surface fabricated as above and we find that it is appropriate for electronic applications (an interface trap density below 1–3×10¹⁰ eV⁻¹ cm⁻² is obtained, indicative of the high quality of the thermal silicon oxide).     

SiO2/Si衬底上石墨烯的制备与结构表征

在分子束外延(MBE)设备中,利用直接沉积C原子的方法在覆盖有SiO₂的Si衬底(SiO₂/Si)上生长石墨烯,并通过Raman光谱和近边X射线吸收精细结构谱等实验技术对不同衬底温度(500℃,600℃,700℃,900℃,1100℃,1200℃)生长的薄膜进行结构表征.实验结果表明,在衬底温度较低时生长的薄膜是无定形碳,在衬底温度高于700℃时薄膜具有石墨烯的特征,而且石墨烯的结晶质量随着衬底温度的升高而改善,但过高的衬底温度会使石墨烯质量降低.衬底温度为1100℃时结晶质量最好.衬底温度较低时C原子活性较低,难以形成有序的C-sp²六方环.而衬底温度过高时(1200℃),衬底表面部分SiO₂分解,C原子与表面的Si原子或者O原子结合而阻止石墨烯的形成,并产生表面缺陷导致石墨烯结晶变差.     

Characterization of TiO2/Au/TiO2 films deposited by magnetron sputtering on polycarbonate substrates

Transparent and conducting TiO₂/Au/TiO₂ (TAuT) films were deposited by reactive magnetron sputtering on polycarbonate substrates to investigate the effect of the Au interlayer on the optical, electrical, and structural properties of the films. In TAuT films, the Au interlayer thickness was kept at 5 nm. Although total thickness was maintained at 100 nm, the stack structure was varied as 50/5/45, 70/5/25, and 90/5/5 nm.In XRD pattern, the intermediate Au films were crystallized, while all TAuT films did not show any diffraction peaks for TiO₂ films with regardless of stack structure. The optical and electrical properties were dependent on the stack structure of the films. The lowest sheet resistance of 23 Ω/□ and highest optical transmittance of 76% at 550 nm were obtained from TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm films. The work function was dependent on the film stack. The highest work function (4.8 eV) was observed with the TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm film stack. The TAuT film stack of TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm films is an optimized stack that may be an alternative candidate for transparent electrodes in flat panel displays.     

Preparation and characterization of amine-functionalized SiO2/TiO2 films for formaldehyde degradation

This paper investigated the gaseous formaldehyde degradation by the amine-functionalized SiO₂/TiO₂ photocatalytic films for improving indoor air quality. The films were synthesized via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and 3-aminopropyltrimethoxysilane (APTMS). The physicochemical properties of prepared photocatalysts were characterized with N₂ adsorption/desorption isotherms measurement, X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FT/IR). The effect of amine-functional groups and the ratio of MTMOS/APTMS precursors on the formaldehyde adsorption and photocatalytic degradation were investigated. The results showed that the formaldehyde adsorption and photocatalytic degradation of the APTMS-functionalized SiO₂/TiO₂ film was higher than that of SiO₂/TiO₂ film due to the surface adsorption on amine sites and the relatively high of the specific surface area of the APTMS-functionalized SiO₂/TiO₂ film (15 times higher than SiO₂/TiO₂). The enhancement of the formaldehyde degradation of the film can be attributed to the synergetic effect of adsorption and subsequent photocatalytic decomposition. The repeatability of photocatalytic film was also tested and the degradation efficiency was 91.0% of initial efficiency after seven cycles.     

Coupling between Ge-nanocrystals and defects in SiO2

Room temperature photoluminescence (PL) at around 600 nm from magnetron-sputtered SiO₂ films co-doped with Ge is reported. The PL signal is observed in pure SiO₂, however, its intensity increases significantly in the presence of Ge-nanocrystals (Ge-nc). The PL intensity has been optimized by varying the temperature of heat treatment, type of gas during heat treatment, concentration of Ge in the SiO₂ films, and gas pressure during deposition. Maximum intensity occurs when Ge-nc of around 3.5 nm are present in large concentration in SiO₂ layers deposited at fairly high gas pressure. Based on time resolved PL, and PL measurements after α-particle irradiation or H passivation, we attribute the origin of the PL to a defect in SiO₂ (probably an O deficiency) that is excited through an energy transfer from Ge-nc. There is no direct PL from the Ge-nc; however, there is a strong coupling between excitons created in the Ge-nc and the SiO₂ defect.     

Dielectric properties of barium titanate ceramics modified by SiO2 and by BaO-SiO2

The influence of SiO₂ on the dielectric properties of barium titanate ceramics was investigated. SiO₂ had been doped solely and together with BaO into barium titanate before calcination. X-ray diffraction showed that all the ceramics were of a pure perovskite phase after sintering at 1275 °C for 2 h. For SiO₂-doping, there was about 2.5 °C increase in Curie temperature per molar percentage of doping and the leakage current was obviously increased, especially at low voltages for relatively high doping levels. While for the co-doping of SiO₂ and BaO, there was little change in Curie temperature. The point defects formed through the dopings were proposed responsible for the effects. It was suggested that SiO₂ is important to barium titanate ceramics not only for sintering but also for modifying their properties.     

Preparation and characterization of SiO2/ZrO2/Ag multicoated microspheres

A new type of multicoated silica/zirconia/silver (SiO₂/ZrO₂/Ag) core-shell composite microspheres is synthesized in this paper. In the process, ZrO₂-decorated silica (SiO₂/ZrO₂) core-shell composites were firstly fabricated by the modification of zirconia on silica microspheres through the hydrolysis of zirconium precursor. Subsequently, on SiO₂/ZrO₂ composite cores, silver nanoparticles were introduced via ultrasonic irradiation and acted as “Ag seeds” for the formation of integrate silver shell by further reduction of silver ions using formaldehyde as reducer. The resulting samples were characterized by transmission electron microscopy, X-ray diffraction, Fourier-transform infrared, energy-dispersive X-ray, and UV-vis spectroscopy, indicating that zirconia and silver layers were successfully coated on the surfaces of silica microspheres.     

Sol-gel growth of Gd2MoO6:Eu nanocrystalline layers on SiO2 spheres (SiO2@Gd2MoO6:Eu) and their luminescent properties

SiO₂@Gd₂MoO₆:Eu³⁺ core-shell phosphors were prepared by the sol-gel process. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectra (EDS), transmission electron microscopy (TEM), photoluminescence (PL) spectra as well as kinetic decays were used to characterize the resulting SiO₂@Gd₂MoO₆:Eu³⁺ core-shell phosphors. The XRD results demonstrate that the Gd₂MoO₆:Eu³⁺ layers on the SiO₂ spheres begin to crystallize after annealing at 600 °C and the crystallinity increases with raising the annealing temperature. The obtained core-shell phosphors have a near perfect spherical shape with narrow size distribution (average size ca. 600 nm), are not agglomerated, and have a smooth surface. The thickness of the Gd₂MoO₆:Eu³⁺ shells on the SiO₂ cores could be easily tailored by varying the number of deposition cycles (50 nm for four deposition cycles). The Eu³⁺ shows a strong PL luminescence (dominated by ⁵D₀-⁷F₂ red emission at 613 nm) under the excitation of 307 nm UV light. The PL intensity of Eu³⁺ increases with increasing the annealing temperature and the number of coating cycles.     

Structure and infrared emissivity of collagen/SiO2 composite

Collagen/SiO₂ composites were prepared in aqueous suspensions. Adsorption behaviors of collagen onto the surfaces of SiO₂ spheres were studied. Structure and thermal properties were measured with FTIR, SEM, TEM, and TGA-DTA. The results showed that the self-aggregation of collagen macromolecules was taken place during the adsorption of collagen on SiO₂ sphere. The morphology of collagen evolved from line to microfibrils with the increase in the concentration of collagen along with the distortion of SiO₂. Interfacial interactions of electrostatic forces and hydrogen bonding between the collagen macromolecule and SiO₂ sphere had a vital effect on the adsorption of collagen. The amount of the collagen adsorption was increased with the increase of the collagen concentration, yet decreased in increased pH value of the solution. It was found that the composites exhibited lower infrared emissivity values in the wavelength ranged from 8 to 14 μm than not only pure collagen but also SiO₂ sphere, and the value of infrared emissivity was related to the adsorption amount of collagen in the composites.     

Influence of patterning on the nucleation of Ge islands on Si and SiO2 surfaces

Surface patterning is expected to influence the nucleation site of deposited nanostructures. In the present study, clean Si and SiO₂ surfaces were patterned by a nanolithographic process using a Focused Ion Beam (FIB). Ge was evaporated in ultra high vacuum at 873 K on these substrates, resulting in the formation of island arrays. Based on scanning tunneling microscopy and atomic force microscopy images, a statistical analysis was performed in order to highlight the effect of patterning on the size distribution of islands compared to a non-patterned surface. We find that the self-organization mechanism on patterned substrates results in a very good arrangement and positioning of Ge nanostructures, depending on growth conditions and holes distance, both on Si and SiO₂ surfaces.     

Immobilization of glucose oxidase using CoFe2O4/SiO2 nanoparticles as carrier

Aminated-CoFe₂O₄/SiO₂ magnetic nanoparticles (NPs) were prepared from primary silica particles using modified StÖber method. Glucose oxidase (GOD) was immobilized on CoFe₂O₄/SiO₂ NPs via cross-linking with glutaraldehyde (GA). The optimal immobilization condition was achieved with 1% (v/v) GA, cross-linking time of 3 h, solution pH of 7.0 and 0.4 mg GOD (in 3.0 mg carrier). The immobilized GOD showed maximal catalytic activity at pH 6.5 and 40 °C. After immobilization, the GOD exhibited improved thermal, storage and operation stability. The immobilized GOD still maintained 80% of its initial activity after the incubation at 50 °C for 25 min, whereas free enzyme had only 20% of initial activity after the same incubation. After kept at 4 °C for 28 days, the immobilized and free enzyme retained 87% and 40% of initial activity, respectively. The immobilized GOD maintained approximately 57% of initial activity after reused 7 times. The K_M (Michaelis-Menten constant) values for immobilized GOD and free GOD were 14.6 mM and 27.1 mM, respectively.     

Structural and optical properties of Si/SiO2 multi-quantum wells

Structural and optical properties of Si/SiO₂ multi-quantum wells (MQW) were investigated by means of Raman scattering and photoluminescence (PL) spectroscopy. The MQW structures were fabricated on a quartz substrate by remote plasma enhanced chemical vapour deposition (RPECVD) of alternating amorphous Si and SiO₂ layers. After layer deposition the samples were subjected to heat treatments, i.e. rapid thermal annealing (RTA) and furnace annealing. Distinct PL signatures of confined carriers evidenced formation of Si-nanocrystals (nc-Si) in annealed samples. Analyses of Raman spectra also show presence of nc-Si phase along with amorphous-Si (a-Si) phase in the samples. The strong influence of the annealing parameters on the formation of nc-Si phase suggests broad possibilities in engineering MQW with various optical properties. Interestingly, conversion of the a-Si phase to the nc-Si phase saturates after certain time of furnace annealing. On the other hand, thinner Si layers showed a disproportionately lower crystalline volume fraction. From the obtained results we could assume that an interface strain prevents full crystallization of the Si layers and that the strain is larger for thinner Si layers. The anomalous dependence of nc-Si Raman scattering peak position on deposited layer thickness observed in our experiments also supports the above assumption.     

Concentration effect of Tm on cathodoluminescence properties of SiO2:Tm and SiO2:Ho,Tm systems

Cathodoluminescence (CL) properties of SiO₂ powders activated with thulium (Tm³⁺) and holmium (Ho³⁺) ions prepared by a sol–gel process were investigated. Different molar concentrations of Tm³⁺ co-doped with Ho³⁺ were studied. The 460 nm peak was monitored and the influence of the beam energy and concentration of Tm³⁺ ions on the emission properties of this peak was also monitored. The peculiar behavior whereby the 460 nm emission peak decreases and the increase in the 705 and 865 nm peaks with the increase in the concentration of Tm³⁺ ions is reported. The relationship between the accelerating beam voltage and the CL intensity of the blue emission peak (460 nm peak) is established. Morphology, particle size and optical properties were characterized with Scanning electron microscopy (SEM), UV/VIS Lambda 750 S spectrometer and Auger electron spectroscopy (AES) equipped with Ocean Optics S2000, respectively.