Synthesis and luminescence properties of nanocrystalline Gd2O3:Eu by combustion process

The nanocrystalline Gd₂O₃:Eu³⁺ powders with cubic phase were prepared by a combustion method in the presence of urea and glycol. The effects of the annealing temperature on the crystallization and luminescence properties were studied. The results of XRD show pure phase can be obtained, the average crystallite size could be calculated as 7, 8, 15, and 23 nm for the precursor and samples annealed at 600, 700 and 800 °C, respectively, which coincided with the results from TEM images. The emission intensity, host absorption and charge transfer band intensity increased with increasing the temperature. The slightly broad emission peak at 610 nm for smaller particles can be observed. The ratio of host absorption to O²⁻-Eu³⁺ charge transfer band of smaller nanoparticles is much stronger compared with that for larger nanoparticles, furthermore, the luminescence lifetimes of nanoparticles increased with increasing particles size. The effects of doping concentration of Eu³⁺ on luminescence lifetimes and intensities were also discussed. The samples exhibited a higher quenching concentration of Eu³⁺, and luminescence lifetimes of nanoparticles are related to annealing temperature of samples and the doping concentration of Eu³⁺ ions.     

Porous WO3 from anodized sputtered tungsten thin films for NO2 detection

In this paper, porous WO₃ films were prepared by anodic oxidation of metallic tungsten (W) films deposited on alumina substrates. The structural and morphological properties of the porous WO₃ films were investigated using field emission scanning electron microscope (FESEM) and X-ray diffraction (XRD). A large number of cracks appeared on the surface of films after anodization, which makes the films porous. The porous WO₃ sensors achieved their maximum response values to NO₂ at a low operating temperature of 150 °C. The porous WO₃ sensors showed high response values, great stability and fast response-recovery characteristics to different concentration of NO₂ gas due to the high specific surface area and special structural and morphological properties.     

Surface study of fine MgFe2O4 ferrite powder prepared by chemical methods

To study surface behaviors, MgFe₂O₄ ferrite materials having different grain sizes were synthesized by two different chemical methods, i.e., a polymerization method and a reverse coprecipitation method. The single phase of the cubic MgFe₂O₄ was confirmed by the X-ray diffraction method for both the precursors decomposed at 600-1000 °C except for a very small peak of Fe₂O₃ was detected for the samples calcined at 600 and 700 °C by the polymerization method. The crystal size and particle size increased with an increase in the sintering temperature using both methods. The conductance of the MgFe₂O₄ decreased when the atmosphere was changed from ambient air to air containing 10.0 ppm NO₂. The conductance change, C = G(air)/G(10 ppm NO₂), was reduced with an increase in the operating temperature. For the polymerization method, the maximum C-value was ca. 40 at 300 °C for the samples sintered at 900 °C. However, the samples sintered at 1000 °C showed a low conductance change in the 10 ppm NO₂ gas, because the ratio of the O₂ gas adsorption sites on the particle surface is smaller than those of the samples having a high C-value. The low Mg content on the surface affects the low ratio of the gas adsorption sites. For the reverse coprecipitation method, the particle size was smaller than that of the polymerization method. Although a stable conductance was obtained for the sample sintered at 900 and 1000 °C, its conductance change was less than that of the polymerization method.     

Synthesis and characterization of TiO2/Fe2O3 core-shell nanocomposition film and their photoelectrochemical property

TiO₂/Fe₂O₃ core-shell nanocomposition film has been fabricated via two-step method. TiO₂ nanorod arrays are synthesized by a facile hydrothermal method, and followed by Fe₂O₃ nanoparticles deposited on TiO₂ nanorod arrays through an ordinary chemical bath deposition. The phase structures, morphologies, particle size, chemical compositions of the composites have been characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) and ultraviolet-visible (UV-vis) spectrophotometer. The results confirm that Fe₂O₃ nanoparticles of mean size ca. 10 nm coated on the surface of TiO2 NRs. After depositing Fe₂O₃, UV-vis absorption property is induces the shift to the visible-light range, the annealing temperature of 600 °C is the best condition for UV-vis absorption property of TiO₂/Fe₂O₃ nanocomposite film, and increasing Fe content, optical activity are enhanced one by one. The photoelectrochemical (PEC) performances of the as-prepared composite nanorods are determined by measuring the photo-generated currents under illumination of UV-vis light. The TiO₂ NRs modified by Fe₂O₃ show the photocurrent value of 1.36 mA/cm² at 0 V vs Ag/AgCl, which is higher than those of unmodified TiO₂ NRs.     

Effects of deposition parameters on laser-induced damage threshold of Ta2O5 films

Ta₂O₅ films were deposited on BK7 substrates by e-beam evaporation with different deposition parameters such as substrate temperature (323-623 K), oxygen pressure (0.5-3.0×10⁻² Pa) and deposition rate (0.2-0.5 nm/s). Absorption, scattering and chemical composition were investigated by surface thermal lensing (STL) technique, total integrated scattering (TIS) measurement and X-ray photoelectron spectroscopy (XPS), respectively. The laser-induced damage threshold (LIDT) was assessed using pulsed Nd:YAG 1064 nm laser at a pulse length of 12 ns. The results showed that optical properties, absorption and LIDT were influenced by the deposition parameters and annealing. However, scattering was little correlated with the deposition parameters. On the whole, the LIDT increased with increasing substrate temperature and oxygen pressure, whereas it increased firstly and then decreased upon increasing deposition rate. After annealing at 673 K for 12 h, the LIDT of films improved significantly. The dependence of possible damage mechanism on deposition parameters was discussed.     

Fabrication and evolution of Cu nanoparticles in Al2O3 crystal by ion implantation and annealing at different atmospheres

Single crystal Al₂O₃ samples were implanted with 45 keV Cu ion implantation at a dose of 1 × 10¹⁷ ions/cm², and then subjected to furnace annealing in vacuum or with a flow of oxygen gas. Various techniques, such as ultraviolet-visible spectroscopy, X-ray diffraction spectroscopy and atomic force microscopy, have been used to investigate formation of Cu NPs and their evolution. Our results clearly show that the evolution of Cu NPs depends strongly on annealing atmosphere in the temperature range up to 600 °C. Annealing in vacuum only gives rise to a slight change in the size of Cu NPs. No evidence for oxidization of Cu NPs has been revealed. Remarkable modifications in Cu NPs, including the size increase and the effective transformation into CuO NPs, have been observed for the samples annealed at oxygen atmosphere. The results have been tentatively discussed in combination with the role of oxygen from atmosphere in diffusion of Cu atoms towards the surface and its interactions with Cu NPs during annealing.     

Precipitate synthesis of BaMoO4 and BaWO4 nanoparticles at room temperature and their photoluminescence properties

The uniform BaMoO₄ and BaWO₄ nanoparticles (NPs) have been successfully synthesized by solution route – the direct precipitation of Ba(NO₃)₂ and Na₂MO₄ (M = Mo and W) in ethylene glycol under 24 h stirring. The XRD patterns and SEM images proved that the products were tetragonal structured BaMoO₄ and BaWO₄ with uniform round nanoparticles. Shape, average particle size and particle-size distribution of products were analyzed by TEM – showing the round nanoparticles with the average size of 31.52 ± 4.65 nm for BaMoO₄, and 59.77 ± 9.61 nm for BaWO₄. The room temperature photoluminescence (PL) indicated that the products have strong blue emission centered at 441 nm – excited with 280 nm wavelength for BaMoO₄ NPs, and strong violet emission centered 378 nm – excited with 344 nm wavelength for BaWO₄ NPs. These PL behaviors attributed the existence of intrinsic transitions in the [MO₄]^2-$[{\text{MO}}_4{]}^{2-}$ (M = Mo and W) tetrahedrons of their crystal lattices.     

Sol-gel growth of Gd2MoO6:Eu nanocrystalline layers on SiO2 spheres (SiO2@Gd2MoO6:Eu) and their luminescent properties

SiO₂@Gd₂MoO₆:Eu³⁺ core-shell phosphors were prepared by the sol-gel process. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectra (EDS), transmission electron microscopy (TEM), photoluminescence (PL) spectra as well as kinetic decays were used to characterize the resulting SiO₂@Gd₂MoO₆:Eu³⁺ core-shell phosphors. The XRD results demonstrate that the Gd₂MoO₆:Eu³⁺ layers on the SiO₂ spheres begin to crystallize after annealing at 600 °C and the crystallinity increases with raising the annealing temperature. The obtained core-shell phosphors have a near perfect spherical shape with narrow size distribution (average size ca. 600 nm), are not agglomerated, and have a smooth surface. The thickness of the Gd₂MoO₆:Eu³⁺ shells on the SiO₂ cores could be easily tailored by varying the number of deposition cycles (50 nm for four deposition cycles). The Eu³⁺ shows a strong PL luminescence (dominated by ⁵D₀-⁷F₂ red emission at 613 nm) under the excitation of 307 nm UV light. The PL intensity of Eu³⁺ increases with increasing the annealing temperature and the number of coating cycles.     

Blue luminescence in Tm-doped KGd(WO4)2 single crystals

Up-conversion blue emissions of trivalent thulium ions in monoclinic KGd(WO₄)₂ single crystals at 454 and 479 nm are reported for a single pump laser source at 688 nm. We grew thulium-doped KGd(WO₄)₂ single crystals at several concentrations from 0.1% to 10%. We recorded a polarized optical absorption spectrum for the ³F₂+³F₃ energy levels of thulium at room temperature and low temperature (6 K). From the low temperature emission spectra we determined the splitting of the ³H₆ ground state. The blue emissions are characterized as a function of the dopant concentration and temperature from 10 K to room temperature. To our knowledge, this is the first time that sequential two-photon excitation process (STEP) generated blue emissions in thulium-doped single crystals with a single excitation wavelength.     

In-situ bridging of SnO2 nanowires between the electrodes and their NO2 gas sensing characteristics

A simple and efficient way of making highly sensitive SnO₂ nanowire-based gas sensors without an individual lithography process was studied. The SnO₂ nanowires network was floated upon the Si substrate by separating the Au catalyst layer from the substrate. As the electric current is transported along the networks of the nanowires, not along the surface layer on the substrate, the gas sensitivities could be maximized in this networked and floated structures. The sensitivity was 5-30 when the NO₂ concentration was 1-10 ppm. The response time was ca. 20-60 s.     

Effect of annealing on TiO2 nanoparticles

TiO₂ nanoparticles have been prepared by simple chemical precipitation method and annealed at different temperatures. The as-prepared TiO₂ are amorphous, and they transform into anatase phase on annealing at 450 °C, and rutile phase on annealing at 900 °C. The X-ray diffraction results showed that TiO₂ nanoparticles with grain size in the range of 21–24 nm for anatase phase and 69–74 nm for rutile phase have been obtained. FESEM images show the formation of TiO₂ nanoparticles with small size in structure. The FTIR and Raman spectra exhibited peaks corresponding to the anatase and rutile structure phases of TiO₂. Optical absorption studies reveal that the absorption edge shifts towards longer wavelength (red shift) with increase of annealing temperature.     

Preparation and characterization of novel Pd/SiO2 and Ca-Pd/SiO2 egg-shell catalysts with porous hollow silica

Novel egg-shell structured monometallic Pd/SiO₂ and bimetallic Ca-Pd/SiO₂ catalysts were prepared by an impregnation method using porous hollow silica (PHS) as the support and PdCl₂ and Ca(NO₃)₂·4H₂O as the precursors. It was found from transmission electron microscope (TEM), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) that Pd was loaded on PHS with a particle size of 5-12 nm in Pd/SiO₂ samples and the Pd particle size in Ca-Pd/SiO₂ was smaller than that in Pd/SiO₂ since Ca could prevent Pd particles from aggregating. X-ray photoelectron spectroscopy (XPS) analyses exhibited that Pd 3d_5/2 binding energies of Pd/SiO₂ and Ca-Pd/SiO₂ were 0.2 and 0.9 eV lower than that of bulk Pd, respectively, as a result of the shift of the electron cloud from Pd to oxygen in Pd/SiO₂ and to both oxygen and Ca in Ca-Pd/SiO₂. The activity of Ca-Pd/SiO₂ egg-shell catalyst for CO hydrogenation and the selectivity to methanol, with a value of 36.50 mmol_CO mol⁻¹_Pd s⁻¹ and 100%, respectively, were much higher than those of the catalysts prepared with traditional silica gel as the support, owing to the porous core-shell structure of the PHS support.     

VO2-WO3 nanocomposite thin films synthesized by pulsed laser deposition technique

Pure VO₂ and VO₂-WO₃ composite thin films were grown on quartz substrate by pulsed laser deposition (PLD) technique. The influence of varying WO₃ molar concentration in the range from x = 0.0 to x = 0.4 on structural, electrical and optical properties of VO₂-WO₃ nanocomposite thin films has been systematically investigated. X-ray diffraction studies reveal the single crystalline monoclinic VO₂ phase (m-VO₂) up to 10% of WO₃ content whereas both m-VO₂ as well as h-WO₃ (hexagonal WO₃) phases were present at higher WO₃ content (0.2 ≤ x ≤ 0.4). Optical transmittance spectra of the films showed blue shift in the absorption edge with increase in WO₃ content. Temperature dependence of resistivity (R-T) measurements indicates significant variation in metal-insulator transition temperature, width of the hysteresis, and shape of the hysteresis curve. Cyclic Voltammetry measurements were performed on VO₂-WO₃ thin films. A direct correlation between V/W ratio and structure-property relationship was established. The present investigations reveal that doping of WO₃ in VO₂ is effective to increase the optical transmittance and to reduce the semiconductor to metal phase transition temperature close to room temperature.     

Investigation on spectral features of tungsten ions in PbO-Bi2O3-As2O3 glass matrix

Lead bismuth arsenate glasses mixed with different concentrations of WO₃ (ranging from 0 to 6.0 mol%) were synthesized. Differential thermal analysis (DTA), optical absorption, ESR and IR spectral studies have been carried out. The results of DTA have indicated that there is a gradual decrease in the resistance of the glass against devitrification with increase in the concentration of WO₃ upto 4.0 mol%.The optical absorption spectra of these glasses exhibited a relatively broad band peaking at about 880 nm identified due to d_xy→d_x²_−y² transition of W⁵⁺ ions; this band is observed to be more intense in the spectrum of glass containing 4.0 mol% of WO₃. Further, two prominent kinks attributed to ³P₀→¹S₀, ¹D₂ transitions of Bi³⁺ ions have also been located in the absorption spectra. The ESR spectra of these glasses recorded at room temperature exhibited an asymmetric signal at g_⊥∼1.71 and g_ll∼1.61. The intensity of the signal is observed to be maximal for the spectrum of the glass W₄. The quantitative analysis of optical absorption and ESR spectral studies have indicated that there is a maximum reduction of tungsten ions from W⁶⁺ state to W⁵⁺ state in the glass containing 4.0 mol% of WO₃. The IR spectral studies have indicated that there is a increasing degree of disorder in the glass network with increase in the concentration of WO₃ upto 4.0 mol%.     

STM and XPS characterisation of vacuum annealed nanocrystalline WO3 films

Scanning tunnelling microscopy and X-ray Photoelectron Spectroscopy were conducted on magnetron sputtered WO₃ thin films, following a sequence of ultra high vacuum anneals from 100 °C to 900 °C. Annealing from 100 °C to 400 °C induced an upward surface band bending of about 0.3 eV, attributed to the oxygen migration from the bulk to the surface, but no changes in the surface topography. Chemical changes occurred from 600 °C to 800 °C, associated with the formation of secondary oxide species. STM imaging showed that the film surface consists of amorphous particles 35 nm in size up to 600 °C, while higher temperatures resulted in an increase in particle size. Crystallisation of the nanoparticles started to occur after annealing at 600 °C. The implications in terms of gas sensing are discussed.     

Synthesis and photoluminescence properties of aqueous CdWO4 quantum dots with WO6 luminescence center

Aqueous CdWO₄ QDs were synthesized by the reaction of CdCl₂ and Na₂WO₄ in the presence of mercaptoacetic acid (TGA) as capping reagent. The crystal morphology, particle size and its distribution of as-prepared products were characterized by transmission electron microscopy (TEM, SAED) atomic force microscopy (AFM), high-resolution transmission electron microscopy (HRTEM), and photon correlation spectroscopy (PCS), respectively. Qualitative assays for functional groups on the QDs’ surface were measured by fourier transform infrared spectroscopy (FTIR). Photoluminescence properties of QDs were studied by photoluminescence spectroscopy (PL). The results showed that the single QD with diameter of about 8 ± 2 nm was single-crystal. The particle size distribution of QDs was normal. Infrared absorption bands of carboxylic group on the surface of CdWO₄ QDs were observed around 1610-1550 cm⁻¹ (nonsymmetrical vibration of -COO⁻) and 1400 cm⁻¹ (symmetric vibration of C-O). With reaction-time going, PL peak position shifted from 498 to 549 nm and intensity of PL increased first and then decreased. PL peak position of QDs was blue-shift compared with 570 nm WO₆⁶⁻ luminescence center of bulk CdWO₄.     

Density functional theory study of NO2-sensing mechanisms of pure and Ti-dopedWO3 （002） surfaces

Density functional theory (DFT) calculations are employed to explore the NO₂-sensing mechanisms of pure and Ti-doped WO₃ (002) surfaces. When Ti is doped into the WO₃ surface, two substitution models are considered: substitution of Ti for W_6c and substitution of Ti for W_5c. The results reveal that substitution of Ti for 5-fold W forms a stable doping structure, and doping induces some new electronic states in the band gap, which may lead to changes in the surface properties. Four top adsorption models of NO₂ on pure and Ti-doped WO₃ (002) surfaces are investigated: adsorptions on 5-fold W (Ti), on 6-fold W, on bridging oxygen, and on plane oxygen. The most stable and likely NO₂ adsorption structures are both N-end oriented to the surface bridge oxygen O_1c site. By comparing the adsorption energy and the electronic population, it is found that Ti doping can enhance the adsorption of NO₂, which theoretically proves the experimental observation that Ti doping can greatly increase the WO₃ gas sensor sensitivity to NO₂ gas.     

Study of the synthesis and Cl2 gas-sensing properties of nanometer HNO3-doped SnO2

We focused on the effects of the inorganic acid HNO₃ on the gas-sensing properties of nanometer SnO₂ and prepared the powders via a dissolution-pyrolysis method. Furthermore, the powders were characterized by means of X-ray diffraction (XRD), scanning electron microscope (SEM), field emission scanning electron microscopy (FESEM) and energy-dispersive X-ray spectra (EDS). Several aspects were surveyed, including the calcining temperature, concentration of nitric acid and the working temperature. The results showed that the gas response of 3 wt% HNO₃-doped SnO₂ powders (calcined at 500 °C) to 10 ppm Cl₂ reached 316.5, at the working temperature 175 °C. Compared with pure SnO₂, appropriate HNO₃ could increase the gas sensitivity to Cl₂ gas more significantly.     

Silica-coated Y2O3:Eu nanoparticles and their luminescence properties

Crystalline Y₂O₃:Eu is of paramount significance in rare earth materials and research on luminescence spectra. In this work, the nanocrystalline Y₂O₃:Eu was coated with silica by a facile solid state reaction method at room temperature. The transmission electron microscope (TEM) photographs showed that the prepared Y₂O₃:Eu particle is polycrystalline with the size of 20 nm, the size of silica-coated particle is about 25 nm. The XPS spectra indicated that the silica layer is likely to interact with Y₂O₃:Eu by a Si-O-Y chemical bond. The luminescence spectra showed that the intensity of ground samples is lower than that of unground ones, the intensity of silica-coated phosphors is higher than that of the ground samples, while almost the same as that of the unground ones. Therefore, the silica coating decreases the surface defects of nanoparticles of the nanocrystalline Y₂O₃:Eu, thus increasing their luminescent intensity.     

Thermal stability, oxygen non-stoichiometry and transport properties of LaNi0.6Fe0.4O3

Thermal stability, oxygen non-stoichiometry and electrical conductivity of LaNi_0.6Fe_0.4O_3−δ were investigated in the temperature region of 20-1000 °C in Ar/O₂ gas flows at oxygen partial pressures between 0.5 and 21,000 Pa. Diffusion mobility was measured in Ar/O₂ gas flow at pO₂ = 18 Pa. Crystal structure of this compound was found to be stable at the mentioned experimental conditions. LaNi_0.6Fe_0.4O_3−δ is a p-type semiconductor with metallic type conductivity above 150 °C at the investigated pO₂ range. Two different (fast and slow) oxygen exchange areas on the temperature-pO₂ diagram were established, which are due to two different oxygen anion positions in the double B-site mixed perovskite structure. Oxygen non-stoichiometry in the fast oxygen exchange region reaches about 0.005 of oxygen atomic index. Chemical diffusion and oxygen surface exchange coefficients do not vary at 600-800 °C, but show visible increase above 800-850 °C.