Comparative study of ethanol sensor based on gold nanoparticles: ZnO nanostructure and gold: ZnO nanostructure

Gold colloid:ZnO nanostructures were prepared from Zn powder by using thermal oxidation technique on alumina substrates, then it was impregnated by gold colloid for comparative study. The gold colloid is the solution prepared by chemical reduction technique; it appeared red color for gold nanoparticle solution and yellow color for gold solution. The heating temperature and sintering time of thermal oxidation were 700 °C and 24 h, respectively under oxygen atmosphere. The structural characteristics of gold colloid:ZnO nanostructures and pure ZnO nanostructures were studied using filed emission scanning electron microscope (FE-SEM). From FE-SEM images, the diameter and length of gold colloid:ZnO nanostructures and ZnO nanostructures were in the ranges of 100-500 nm and 2.0-7.0 μm, respectively. The ethanol sensing characteristics of gold colloid:ZnO nanostructures and ZnO nanostructures were observed from the resistance alteration under ethanol vapor atmosphere at concentrations of 50, 100, 200, 500, and 1000 ppm with the operating temperature of 260-360 °C. It was found that the sensitivity of sensor depends on the operating temperature and ethanol vapor concentrations. The sensitivity of gold colloid:ZnO nanostructures were improved with comparative pure ZnO nanostructures, while the optimum operating temperature was 300 °C. The mechanism analysis of sensor revealed that the oxygen species on the surface was O²⁻.     

Improvement of ZnO nanorod-based dye-sensitized solar cell efficiency by Al-doping

The current study investigates the performance of dye-sensitized solar cells (DSSCs) based on Al-doped and undoped ZnO nanorod arrays synthesized by a simple hydrothermal method. Current density-voltage (J-V) characterizations indicate that Al-doping in ZnO crystal structure can significantly improve current densities and the energy conversion efficiency (η) of ZnO nanorod-based DSSCs. The maximum η, 1.34%, was achieved in DSSC when Al-doped ZnO nanorod arrays were grown in 0.04 M zinc acetate dihydrate solution with 5 mM aluminum nitrate nonahydrate. This result represents a large increase of η in Al-doped ZnO nanorod-based DSSCs as compared to undoped (0.05%). The improved DSSC photovoltaic performance can be attributed to two main factors: (1) increased light harvesting efficiency due to a large amount of N719 adsorbed on the large surface area of Al-doped ZnO nanorod arrays, and (2) increased electrical conductivity due to A1³⁺ ion doped into the ZnO lattice at the divalent Zn²⁺ site, allowing electrons to move easily into the Al-doped ZnO conduction band.     

Interfacial engineering of CuO nanorod/ZnO nanowire hybrid nanostructure photoanode in dye-sensitized solar cell

Developing efficient and cost-effective photoanode plays a vital role determining the photocurrent and photovoltage in dye-sensitized solar cells (DSSCs). Here, we demonstrate DSSCs that achieve relatively high power conversion efficiencies (PCEs) by using one-dimensional (1D) zinc oxide (ZnO) nanowires and copper (II) oxide (CuO) nanorods hybrid nanostructures. CuO nanorod-based thin films were prepared by hydrothermal method and used as a blocking layer on top of the ZnO nanowires’ layer. The use of 1D ZnO nanowire/CuO nanorod hybrid nanostructures led to an exceptionally high photovoltaic performance of DSSCs with a remarkably high open-circuit voltage (0.764 V), short current density (14.76 mA/cm² under AM1.5G conditions), and relatively high solar to power conversion efficiency (6.18%) . The enhancement of the solar to power conversion efficiency can be explained in terms of the lag effect of the interfacial recombination dynamics of CuO nanorod-blocking layer on ZnO nanowires. This work shows more economically feasible method to bring down the cost of the nano-hybrid cells and promises for the growth of other important materials to further enhance the solar to power conversion efficiency.     

40% Efficiency enhancement in solar cells using ZnO nanorods as shell prepared via novel hydrothermal synthesis

Herein, rod-like ZnO nanostructures were synthesized via a novel hydrothermal route using Zn(OAc)₂, ethylenediamine and hydrazine as a new set of starting reagents. The as-synthesized products were characterized by techniques including XRD, EDS, SEM, XPS, Pl and FTIR. The prepared ZnO nanostructures were utilized as shell on TiO₂ film in DSSCs. Effect of precursor type, morphology and thickness of ZnO shell (number of electrophoresis cycle) on solar cells efficiency were well studied. Our results showed that ethylenediamine has crucial effect on morphology of synthesized ZnO nanostructures and using ZnO nanostructures leads to an increase in DSSCs efficiency compared to bare TiO₂ from 4.66 to 7.13% (~40% improvement). Moreover, highest amount of solar cell efficiency (7.13%) was obtained by using ZnO nanorods with two cycle of electrophoresis for deposition.     

Enhanced photoelectrochemical performance of ZnO photoanode with scattering hollow cavities

Abstract ZnO nanoparticles with average diameter of 12 nm were used to fabricate ZnO photoanodes by electrohydrodynamic (EHD) technique for dye-sensitized solar cells (DSSCs). To enhance the light scattering and conversion efficiency, the ZnO film with scattering hollow cavities (HCs) was realized by calcining polystyrene spheres (PSs) in the film. The films had strong light scattering ability and the overall light to electricity conversion efficiency (η) was improved and reached 5.5% under illumination of simulated solar light (AM-1.5, 100 mW/cm²).     

Dye-sensitized solar cells based on ZnO nanowire array/TiO2 nanoparticle composite photoelectrodes with controllable nanowire aspect ratio

The ZnO nanowire (NW) array/TiO₂ nanoparticle (NP) composite photoelectrode with controllable NW aspect ratio has been grown from aqueous solutions for the fabrication of dye-sensitized solar cells (DSSCs), which combines the advantages of the rapid electron transport in ZnO NW array and the high surface area of TiO₂ NPs. The results indicate that the composite photoelectrode achieves higher overall photoelectrical conversion efficiency (η) than the ZnO NW alone. As a result, DSSCs based on the ZnO NW array/TiO₂ NP composite photoelectrodes get the enhanced photoelectrical conversion efficiency, and the highest η is also achieved by rational tuning the aspect ratio of ZnO NWs. With the proper aspect ratio (ca. 6) of ZnO NW, the ZnO NW array/TiO₂ NP composite DSSC exhibits the highest conversion efficiency (5.5 %). It is elucidated by the dye adsorption amount and interfacial electron transport of DSSCs with the ZnO NW array/TiO₂ NP composite photoelectrode, which is quantitatively characterized using the UV-Vis absorption spectra and electrochemical impedance spectra. It is evident that the DSSC with the proper aspect ratio of ZnO NW displays the high dye adsorption amount and fastest interfacial electron transfer.     

Natural dye-based photoelectrode for improvement of solar cell performance

In the present paper, photovoltaic studies of dye-sensitized solar cells (DSSCs) based on betacyanin/TiO₂ and betacyanin/WO₃–TiO₂ have been done. The cell performances were compared through I–V curves and wavelength dependant photocurrent measurements for the two new types of DSSCs. The TiO₂-coated DSSC showed the photovoltage and photocurrent of 300 mV and 4.96 mA/cm², whereas the cell employing WO₃–TiO₂ photoelectrode showed the values 435 mV and 9.86 mA/cm², respectively. The conversion efficiency of TiO₂ based dye-sensitized solar cell was found to be 0.69 %, while WO₃–TiO₂-based cell exhibited a higher conversion efficiency of 2.2 %. The better performance of the WO₃–TiO₂ dye-sensitized solar cell photoelectrode is thought to be due to an inherent energy barrier at the electrode/electrolyte interface leading to the reduced recombination of photoinduced electrons.     

ZnO/TiO2 core–shell nanowire arrays for enhanced dye-sensitized solar cell efficiency

We present a new method of synthesizing ZnO/TiO₂ core–shell nanowire (NW) arrays for the fabrication of dye-sensitized solar cells (DSSCs). Vertically aligned ZnO NW arrays were obtained on Si substrates, and modified by a TiO₂ shell in order to solve the recombination problems via a cost-effective spin-coating method. The structure of the ZnO/TiO₂ composite NW arrays was characterized. The experimental results indicate that the TiO₂ shell enhances the performance of the DSSCs, through improving the stability of the ZnO NWs and decreasing the recombination of photogenerated electrons on the NW surface. The highest overall conversion efficiency of the cell reaches about 3.0 %.     

Successive ionic layer adsorption and reaction of ZnSe shells for ZnO nanowire-based dye-sensitized solar cells

Thin ZnSe layers were deposited on ZnO nanowires by a novel successive ionic layer adsorption and reaction technique in order to solve recombination problems in ZnO nanowire-based dye-sensitized solar cells (DSSCs). Cell efficiency increased from 0.1 to 1.3–1.4% with the deposition of a 9- to13-nm-thick ZnSe shell on ZnO nanowires due to a large increase in J_SC. The dramatic increase in J_SC and cell efficiency is due to the facilitation of electron transfer related to ambipolar diffusion by the formation of a type II band alignment and the suppression of recombination in the presence of the ZnSe shell.     

One-pot,large-scale synthesis silica-encapsulated NIR alloy quantum dots CdSeTe within short time

Hydrothermal process has been employed to synthesize titanium oxide (TiO₂) bottle brush. The nanostructured bottle brushes with tetragonal nanorods of ~75 nm diameter have been synthesized by changing the nature of the precursors and hydrothermal processing parameters. The morphological features and structural properties of TiO₂ films were investigated by field emission scanning electron microscopy, X-ray diffraction, high-resolution transmission electron spectroscopy, Fourier transform Raman spectroscopy, and X-ray photoelectron spectroscopy. The influence of such nanostructures on the performance of dye-sensitized solar cells (DSSCs) is investigated in detail. The interface and transient properties of these nanorods and bottle brush-based photoanodes in DSSCs were analyzed by electrochemical impedance spectroscopic measurements in order to understand the critical factors contributing to such high power conversion efficiency. Surface area of sample was recorded using Brunauer–Emmett–Teller measurements. It is found that bottle brush provides effective large surface area 89.34 m² g^?1 which is much higher than TiO₂ nanorods 63.7 m² g^?1. Such effective surface area can facilitate the effective light harvesting, and hence improves the dye adsorption and the photovoltaic performance of DSSCs, typically in short-circuit photocurrent and power conversion efficiency. A best power conversion efficiency of 6.63 % has been achieved. We believe that the present device performance would have wide interests in dye-sensitized solar cell research.     

Porous PVdF-HFP/P123 electrolyte membrane containing flexible quasi-solid-state dye-sensitized solar cells produced by the compression method

Flexible quasi-solid-state dye-sensitized solar cells (DSSCs) with porous poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP)/polyethylene oxide-co-polypropylene oxide-co-polyethylene oxide (P123) electrolyte membranes were fabricated and their photocurrent–voltage (I–V) characteristics are studied. Flexible TiO₂ photoelectrodes were prepared using the compression method and porous PVdF-HFP/P123 membranes, by the nonsolvent-induced phase inversion technique. To activate the electrolyte membrane, the membrane was immersed in liquid-state electrolyte. Increased compression pressure improved the interconnection between TiO₂ nanoparticles, enhancing the photovoltaic performances of the flexible liquid-state DSSCs to a maximum of 3.92% efficiency. Meanwhile, the overall pore structure of the PVdF-HFP/P123 membranes was controlled by varying the blend ratio of P123 to PVdF-HFP. Membranes higher in P123 content gave larger pores and pore volume, increasing the electrolyte uptake of the porous membrane, and thus the ionic conductivity of the electrolyte membrane as well. The photovoltaic characteristics of the flexible quasi-solid-state DSSCs containing a porous PVdF-HFP/P123 electrolyte membrane showed a maximum at 50 wt% P123 content, which gave a short-circuit current density (J_sc) value of 7.28 mA/cm², an open-circuit voltage (V_oc) of 0.67 V, a fill factor (FF) of 0.61 and an energy conversion efficiency (η) of 2.98%. Furthermore, the device designed in this study showed good durability compared to those based on liquid-state electrolyte.     

Experimental investigation on the structural,dielectric, ferroelectric and piezoelectric properties of La doped ZnO nanoparticles and their application in dye-sensitized solar cells

Pure and lanthanum (La) doped ZnO nanorods were synthesized via co-precipitation method. The structure and morphology of as grown ZnO and La-ZnO nanoparticles were studied using transmission electron microscopy (TEM) and powder X-ray diffraction (XRD) methods. The values of remnant polarization and coercive field were found to be 0.027 μC/cm² and 1.33 kV/cm, respectively, for as grown La-ZnO nanostructures. High Curie temperature (276 °C) for doped ZnO was observed in dielectric study. Piezoelectric coefficient at room temperature was found to be 101.30 pm/V. I-V characteristics were studied for both pure and doped ZnO nanoparticles. Photo-anodes of dye-sensitized solar cells (DSSCs) were made using ZnO and La-ZnO nanorods. The conversion efficiency and short circuit current density of La-ZnO nanorods based DSSC were 0.36% and 1.31 mA/cm², respectively, which were found to be largely enhanced when compared with that of pure ZnO based DSSC (0.20% and 0.94 mA/cm²).     

GaN-nanowire-based dye-sensitized solar cells

GaN nanowires typically exhibit high electron mobility and excellent chemical stability. However, stability of GaN is detrimental for successful attachment of dye molecules and its application in dye-sensitized solar cells (DSSCs). Here we demonstrate DSSCs based on GaN/gallium oxide and GaN/TiO _x core–shell structures, and we show that coating of GaN nanowires with a TiO _x shell significantly increases dye adsorption and consequently photovoltaic performance. The best cells exhibited short circuit current density of 1.83 mA/cm² and power conversion efficiency of 0.44% under AM 1.5 simulated solar illumination.     

Modification and photovoltaic properties of reduced graphene oxide/acetylene black composite electrode

A simple and high efficient reduced graphene oxide/acetylene black (rGO/ACET) nano-composite electrode was prepared as the substitute of high-cost Pt counter electrode in dye-sensitized solar cells (DSSCs). Surface-modified method called solvent-substituting (SS) was firstly used to avoid agglomeration of rGO sheets. The Brunner-Emmet-Teller (BET)-specific surface area of rGO was increased from 195.823 to 355.210 m²/g after modifying with ethanol. Then ACET particles were introduced between rGO layers to improve the electronic transportation properties. The chemical compositions, microstructures, and pore size distributions of rGO/ACET composites were investigated. Electrochemical impedance spectroscopy (EIS) indicated that rGO/ACET counter electrode had a lower charge transfer resistance (R_ct) and its S-shaped current–voltage curves disappeared obviously. The highest power conversion efficiency up to 6.62% was achieved for the DSSCs with rGO/ACET nano-composite counter electrode.     

Sputter-deposited ZnO thin films consisting of nano-networks for binder-free dye-sensitized solar cells

ZnO nano-network structures with high porosity were prepared for use in the photoelectrodes of binder-free dye-sensitized solar cells (DSSCs) by DC sputtering and subsequent thermal oxidation. Zn thin films prepared at 100 °C showed nano-network structures with high porosity, while those prepared at 25 °C did not. This was partially attributed to the high mobility of sputter-deposited particles that arrived at the surface of the substrate and partially to a supersaturation mechanism. The prepared nano-network Zn was successfully transformed to ZnO without a morphological change via subsequent annealing in air. The power conversion efficiency of DSSCs based on the ZnO nano-network structures exhibited 10 times higher efficiency than those based on ZnO film prepared at 25 °C because of its large surface area for adsorption of dye molecules. The thickness of the ZnO nano-network structures increased linearly at 10 μm h^?1 as a function of sputter time. As the film thickness increased, the power conversion efficiency of DSSCs increased from 1.09% to 1.82%.     

The effect of Al doping on the morphology and optical property of ZnO nanostructures prepared by hydrothermal process

The undoped and Al-doped ZnO nanostructures were fabricated on the ITO substrates pre-coated with ZnO seed layers using the hydrothermal method. The undoped well-aligned ZnO nanorods were synthesized. When introducing the Al dopant, ZnO shows various morphologies. The morphology of ZnO changes from aligned nanorods, tilted nanorods, nanotubes/nanorods to the nanosheets when the Al doping concentrations increase. The ZnO nanostructures were characterized by X-ray diffraction, field emission scanning electron microscopy, X-ray photoelectron spectroscopy, photoluminescence and Raman technology. The Al doping concentrations play an important role on the morphology and optical properties of ZnO nanostructures. The possible growth mechanism of the ZnO nanostructures was discussed.     

Chemical reactions in TiO2/SnO2/TiCl4 hybrid electrodes and their impacts to power conversion efficiency of dye-sensitized solar cells

This study examined the applicability of TiO₂/SnO₂/TiCl₄ hybrid electrodes in dye-sensitized solar cells (DSSCs) by combining chemical modeling with experimentation. The interfacial chemical reactions in a TiO₂/SnO₂/TiCl₄ system were simulated using a thermochemistry software package, which led to the design and testing of hybrid working electrodes. Chemical thermodynamic modeling proved that TiCl₄ is an effective agent in removing Tiⁿ⁺ (n<4) and Sn^m+ (m<4) ion impurities from dry-mixed TiO₂/SnO₂ composite particles. Our results demonstrate that the power conversion efficiency of DSSC with a TiO₂/SnO₂/TiCl₄ hybrid electrode exceeds that of the conventional DSSC with a TiO₂ electrode due to the effects of light-scattering and the formation of additional absorbance (SnCl₂), which is an unexpected side effect of TiCl₄ treatment enabling the absorption of visible light. The proposed approach is ideally suited to establishing relationships between chemistry theory and the structure and performance of advanced DSSCs as well as photo-electro-chemical systems.     

Dependence of photovoltaic parameters on the size of cations adsorbed by TiO2 photoanode in dye-sensitized solar cells

The effects of “pre-adsorbed cations” in photoanodes on the performances of dye-sensitized solar cells (DSSCs) were studied using two different size cations (K⁺ and guanidine cation (G⁺)). While the DSSCs with optimized K⁺ ions pre-adsorbed photoanodes showed a maximum efficiency of 7.04%, the DSSCs with G⁺ ions pre-adsorbed photoanodes showed an efficiency of 6.73%. DSSCs fabricated with conventional photanodes (without pre-cation adsorption) showed an efficiency of 6.21%. Differences in efficiencies are very likely due to the cation pre-adsorption effects and could be due to a higher number of K⁺ cation adsorption per unit area of TiO₂ surface of the photoanode compared to a smaller number of G⁺ cation adsorption in TiO₂, due to their difference in sizes. This pre-cation adsorption technique can be used to improve the overall efficiency of a DSSC by about 14% fold over the conventional photoanodes use in DSSCs, specially using smaller cations.

     

Utilization of saffron (<Emphasis Type="Italic">Crocus sativus L.</Emphasis>) as sensitizer in dye-sensitized solar cells (DSSCs)

Photoelectrodes of dye-sensitized solar cells (DSSCs) have been prepared using nanosized titanium dioxide that have soaked in a solution of different saffron (Crocus sativus L.) spice content in ethanol. The optimized polyacrylonitrile (PAN)-based gel polymer electrolyte with 40.93 wt.% ethylene carbonate, 37.97 wt.% propylene carbonate, 4.37 wt.% tetrapropylammonium iodide, 9.86 wt.% PAN, 1.24 wt.% 1-butyl-3-methylimidazolium iodide, 4.35 wt.% lithium iodide and 1.28 wt.% iodine has been used as the electrolyte for DSSC. The electrolyte has conductivity of 2.91 mS cm^?1 at room temperature (298 K). DSSCs were also sensitized with saffron solution that has been added with 30 wt.% chenodeoxycholic acid (CDCA) co-adsorbent and designated as DSSC P4. The solar cell converts light-to-electricity at an efficiency of 0.31%. This is 29% enhancement in efficiency for the DSSC without addition of CDCA in the saffron-ethanol solution. The DSSC exhibits current density at short-circuit (J _sc ) of 1.26 mA cm^?2, voltage at open circuit (V _oc ) of 0.48 V and 51% fill factor. DSSC P4 also exhibits the highest incident photon-to-current density of more than 40% at 340 nm wavelength.     

Hydrothermal growth of large-scale macroporous TiO<Subscript>2</Subscript> nanowires and its application in 3D dye-sensitized solar cells

Large-scale macroporous TiO₂ nanowires (MTN) were directly grown on spiral-shaped titanium wires as photoanodes of dye-sensitized solar cells (DSSCs) via a facile hydrothermal reaction without any seeds, templates, and TiO₂ powder. The MTN thin film was characterized by SEM, XRD and TEM. The studies revealed that the MTN thin film had better mechanical properties and provided an efficient pathway for the diffusion of liquid electrolyte. The efficiency of 0.86% for the 3D DSSC was obtained with a J _sc of 2.30 mA/cm², V _oc of 616 mV, and FF of 0.61. This MNT-based mini 3D DSSC is a promising photovoltaic device for applications in the fields of high-integrated micro-electronic equipment.