Cu(In,Ga)Se2 superstrate-type solar cells with Zn1−xMgxO buffer layers

Superstrate-type Cu(In,Ga)Se₂ (CIGS) thin film solar cells were fabricated using Zn_1−xMg_xO buffer layers. Due to the diffusion of Cd into CIGS during the growth of the CIGS layer, the conventional buffer material of CdS is not suitable. ZnO is a good candidate because of higher thermal tolerance but the conduction band offset (CBO) of ZnO/CIGS is not appropriate. In this study, the Zn_1−xMg_xO buffer layers were used to fulfill both the requirements. The superstrate-type solar cells with a soda-lime glass/In₂O₃:Sn/Zn_1−xMg_xO/CIGS/Au structure were fabricated with different band gap energies of the Zn_1−xMg_xO layer. The CIGS layers [Ga/(In + Ga)∼0.25] were deposited by co-evaporation method. The substrate temperature during the CIGS deposition of 450 °C did not cause the intermixing of the Zn_1−xMg_xO and CIGS layers. The conversion efficiency of the cell with Zn_1−xMg_xO was higher than that with ZnO due to the improvement of open-circuit voltage and shunt resistance. The results well corresponded to the behavior of the adjustment of CBO, demonstrating that the usefulness of the Zn_1−xMg_xO layer for the CBO control in the superstrate-type CIGS solar cells.     

Structural and optical properties of ZnO nanorods grown on MgxZn1−xO buffer layers

ZnO nanorod arrays were synthesized by chemical-liquid deposition techniques on Mg_xZn_1−xO (x = 0, 0.07 and 0.15) buffer layers. It is found that varying the Mg concentration could control the diameter, vertical alignment, crystallization, and density of the ZnO nanorods. The X-ray diffraction (XRD), transmission electron microscopy (TEM), and selected area electron diffraction (SAED) data show the ZnO nanorods prefer to grow in the (0 0 2) c-axis direction better with a larger Mg concentration. The photoluminescence (PL) spectra of ZnO nanorods exhibit that the ultraviolet (UV) emission becomes stronger and the defect emission becomes weaker by increasing the Mg concentration in Mg_xZn_1−xO buffer layers.     

Influence of Mg content on optical properties of exciton confinement in wurtzite ZnO/MgxZn1−xO coupled quantum dots

Based on the framework of effective-mass approximation and variational approach, optical properties of exciton are investigated theoretically in ZnO/Mg_xZn_1−xO vertically coupled quantum dots (QDs), with considering the three-dimensional confinement of electron and hole pair and the strong built-in electric field effects. The exciton binding energy, the emission wavelength and the oscillator strength as functions of the structural parameters (the dot height, the barrier thickness between the coupled wurtzite ZnO QDs and Mg content x in the barrier layers) is calculated in detail. The results elucidate that Mg content have a significant influence on the exciton state and optical properties of ZnO coupled QDs. When Mg content x increases, the strong built-in electric field increases and leads to the redshift of the effective band gap of the Mg_xZn_1−xO layer. These theoretical results are useful for design and application of some important photoelectronic devices constructed by using ZnO strained QDs.     

Effect of substrate annealing on the quality of pulsed laser deposited Zn1−xMgxO thin films

The annealing effects of sapphire substrate before deposition on the quality of epitaxial Zn_1−xMg_xO thin films grown by pulsed laser deposition are reported. Our Experimental results indicate that the surface quality of Zn_1−xMg_xO thin films and hexagonal columnar growth is improved on the annealed sapphire substrate at high temperatures due to formation of atomic terraces on the substrate surface. The photoluminescence signals also increases with the increasing annealing temperature of the substrate.     

Oxygen flux influence on the morphological, structural and optical properties of Zn1−xMgxO thin films grown by plasma-assisted molecular beam epitaxy

The Zn_1−xMg_xO thin films were grown on Al₂O₃ substrate with various O₂ flow rates by plasma-assisted molecular beam epitaxy (P-MBE). The growth conditions were optimized by the characterizations of morphology, structural and optical properties. The Mg content of the Zn_1−xMg_xO thin film increases monotonously with decreasing the oxygen flux. X-ray diffractometer (XRD) measurements show that all the thin films are preferred (0 0 2) orientated. By transmittance and absorption measurements, it was found that the band gap of the film decreases gradually with increasing oxygen flow rate. The surface morphology dependent on the oxygen flow rate was also studied by field emission scanning electron microscopy (FE-SEM). The surface roughness became significant with increasing oxygen flow rate, and the nanostructures were formed at the larger flow rate. The relationship between the morphology and the oxygen flow rate of Zn_1−xMg_xO films was discussed.     

用卢瑟福背散射/沟道技术研究ZnO/Zn0.9Mg0.1O/ZnO异质结的弹性应变

利用卢瑟福背散射/沟道技术对射频等离子体辅助分子束外延法生长在蓝宝石衬底上的ZnO/Zn_0.9Mg_0.1O/ZnO异质结进行了组分分析，并得到了异质结弹性应变随深度的变化，应变由界面向表面逐渐释放，并由负变正，且在ZnO与Zn_0.9Mg_0.1O界面处轻微增大.负的应变是由于ZnO与衬底的晶格失配和热失配，而逐渐变为正值是Zn_0.9Mg_0.1O与ZnO的晶格常数差异及弹性应变的 关键词： 异质结 卢瑟福背散射/沟道 弹性应变 ZnMgO     

Growth of cubic MgxZn1−xO alloy films by electron beam evaporation

We report the growth of cubic Mg_xZn_1−xO alloy thin films on quartz by electron beam evaporation. It can be found that all the samples have sharp absorption edges by the absorption measurements. X-ray diffraction measurements indicate the Mg_xZn_1−xO films are cubic phase with preferred orientation along the (1 1 1) direction. Energy dispersive spectrometry (EDS) demonstrates that the Mg concentration in Mg_xZn_1−xO films is much higher than the ceramic target used, and the composition can be tuned in a small scope by varying the substrate temperature and the beam electric current. The reasons of this phenomenon are also discussed.     

Properties of MgxZn1−xO thin films sputtered in different gases

Mg_xZn_1−xO alloy films were prepared on sapphire substrates using Ar and N₂ as the sputtering gases. The effect of the sputtering gas on the structural, optical and electrical properties of the Mg_xZn_1−xO films was studied. By using N₂ as the sputtering gas, the Mg_xZn_1−xO film shows p-type conductivity and the band gap is larger than that employing Ar as the sputtering gas. The reason for this phenomenon is thought to be related to the reaction between N-O or N-Zn, and the N-doping.     

The effect of growth ambient on the structural and optical properties of MgxZn1−xO thin films

Mg_xZn_1−xO (x = 0.0-0.20) thin films have been deposited by sol-gel technique on glass substrates and the effect of growth ambient (air and oxygen) on the structural, and optical properties have been investigated. The films synthesized in both ambient have hexagonal wurtzite structure. The c-axis lattice constant decreases linearly with the Mg content (x) up to x = 0.05, and 0.10 respectively for air- and oxygen-treated films, above which up to x = 0.20, the values vary irregularly with x. The change in the optical band gap values and the ultraviolet (UV) peak positions of Mg_xZn_1−xO films show the similar change with x. These results suggest that the formation of solid solution and thus the structural and optical properties of Mg_xZn_1−xO thin films are affected by the growth ambient.     

Formation of ZnO and Zn1−xCdxO films on CdTe/CdZnTe single crystals

In this work we report on the properties of ZnO and Zn_1−xCd_xO films formed on top of CdTe and CdZnTe single crystals. The films have been obtained by thermal evaporation of Zn metal films and further oxidation in atmospheric conditions. The structural and compositional characteristics of the films have been analysed by means of scanning electron microscopy and energy-dispersive X-ray analysis. The chemical composition of the films as a function of growth parameters has been obtained. It has been possible to demonstrate by Raman spectroscopy the formation of both ZnO and Zn_1−xCd_xO films. The possible inter-diffusion effects between the films and the substrate, derived from the oxidation process, have been discussed. It has been possible to check by means of photoluminescence, the optical quality of the ZnO and Zn_1−xCd_xO films, also regarding to the presence of local changes. Differences between the optical spectra obtained from various ZnO films grown on top of CdTe and CdZnTe substrates enabled the determination of compositional differences introduced by the substrate when the deposition parameters are modified.     

Electric-field-induced energy spectra and dispersions of ZnO/MgxZn1−xO MQWs

The energy spectra and dispersion relations of carriers in the presence of an electric field applied along the growth direction in ZnO/Mg_xZn_1−xO multiple quantum wells (MQW) are calculated using the asymptotic transfer method (ATM) on the basis of the quasistationary state approximation. The energy spectra of the carriers induce some quasi-bound levels under electric fields. The dispersion relations for the energy of the ground state and lower excitation states still have parabolic shapes for both the electrons and the heavy holes in the presence of a moderate electric field. Our results also reveal that the number of energy levels increases with increasing number of ZnO quantum wells and that the energies increase with both increasing Mg composition x and electric field strength.     

Microstructure and thermoelectric properties of Zn1−xAlxO ceramics fabricated by spark plasma sintering

Al-doped ZnO powders were synthesized via solid reaction between Zn(OH)₂ and Al(OH)₃ and consolidated by spark plasma sintering (SPS) to fabricate fine-grained Zn_1−xAl_xO ceramics as a thermoelectric material. X-ray diffraction and spectrophotometer experiments revealed that Al doping into ZnO is enhanced by the present process, and consequently the SPS-processed Zn_1−xAl_xO samples show significantly improved electrical conductivity as compared with those prepared via mixing ZnO and Al₂O₃ oxide powders. Because of the combined effect of Al doping and grain refinement, the present Zn_1−xAl_xO ceramics show much lower thermal conductivity, which also results in an enhanced dimensionless figure of merit (ZT), than un-doped ZnO oxides prepared also by SPS.     

Optical properties of bulk Zn1−xCoxO magnetic semiconductors

Polycrystalline Zn_1−xCo_xO (x=0, 0.02, 0.05, 0.10 and 0.15) oxides have been synthesized by solid state reaction via sintering ZnO and Co powders in open air. X-ray diffraction analyses using Rietveld refinement indicate that a stoichiometric single phase with a wurtzite-like structure was found in Zn_1−xCo_xO samples with x up to 0.10. The elemental mapping using energy dispersive X-ray spectroscopic analyses presents a uniform distribution of Co. Optical transmittance measurements show that several extra absorption bands appear in the Co-doped ZnO, which is due to the transitions between the crystal-field-split 3d levels of tetrahedral Co²⁺ substituting Zn²⁺ ions. Raman measurements show that limited host lattice defects are induced by Co doping. Magnetization measurements reveal that the Co-doped ZnO samples are paramagnetic due to the absence of free carriers and in low temperature the dominant magnetic interaction is nearest-neighbor antiferromagnetic.     

The optical properties of MgxZnl-xO thin films

Mg_xZn_1-xO thin films have been prepared on silicon substrates by radio frequency magnetron sputtering at 60℃. The thin films have hexagonal wurtzite single-phase structure and a preferred orientation with the c-axis perpendicular to the substrates. The refractive indices of Mg_xZn_1-xO films are studied at room temperature by spectroscopic ellipsometry over the wavelength range of 400--760\,nm at the incident angle of 70℃. Both absorption coefficients and optical band gaps of Mg_xZn_1-xO films are determined by the transmittance spectra. While Mg content is increasing, the absorption edges of Mg_xZn_1-xO films shift to higher energies and band gaps linearly increase from 3.24.eV at x=0 to 3.90\,eV at x=0.30. These results provide important information for the design and modelling of ZnO/ Mg_xZn_1-xO heterostructure optoelectronic devices.     

Optical properties of exciton confinement in wurtzite ZnO/MgxZn1−xO coupled quantum dots

Based on the framework of effective-mass approximation and variational approach, optical properties of exciton are investigated theoretically in ZnO/Mg_xZn_1−xO vertically coupled quantum dots (QDs), with considering the three-dimensional confinement of electron and hole pair and the strong built-in electric field effects due to the piezoelectricity and spontaneous polarization. The exciton binding energy, the emission wavelength and the oscillator strength as functions of the different structural parameters (the dot height and the barrier thickness between the coupled wurtzite ZnO QDs) are calculated with the built-in electric field in detail. The results elucidate that structural parameters have a significant influence on the exciton state and optical properties of ZnO coupled QDs. These results show the optical and electronic properties of the quantum dot that can be controlled and also tuned through the nanoparticle size variation.     

Room-temperature ferromagnetism in Zn1−xMnxO

In view of recent controversies on above room-temperature ferromagnetism (RTFM) in transition-metal-doped ZnO, the present paper aims to shed some light on the origin of ferromagnetism by investigating annealing effects on structure and magnetism for polycrystalline Zn_1−xMn_xO powder samples prepared by solid-state reaction method and annealed in air at different temperatures. Magnetic measurements indicate that the samples are ferromagnetic at room temperature (RTFM). Room temperature ferromagnetism has been observed in the sample annealed at a low temperature of 500 °C with a saturated magnetization (M_s) of 0.159 emu/g and a coercive force of 89 Oe. A reduction in RTFM is clearly observed in the sample annealed at 600 °C. Furthermore, the saturation magnetic moment decreases with an increase in grain size, suggesting that ferromagnetism is due to defects and/or oxygen vacancy confined to the surface of the grains. The experimental results indicate that the ferromagnetism observed in Zn_1−xMn_xO samples is intrinsic rather than associated with secondary phases.     

Optical properties of MgxZn1−xO nanowire photonic crystals

We investigate the optical properties of two-dimensional periodic arrays of well-aligned Mg_xZn_1−xO nanowires, i.e., Mg_xZn_1−xO nanowire photonic crystals. The nanowire photonic crystal can exhibit a photonic band gap in the visible range. As the mole fraction of Mg, x, increases, the edge frequencies of the band gap increase and the band gap size decreases. The characteristics of relative band gap and vacant point defect mode are also studied with varying x. From the finite-difference time-domain simulations, we show that the light extraction from nanowires can be controlled by varying the distance between optically excited nanowires and a waveguide, and the mole fraction of Mg. Controlling the light extraction from nanostructures can be useful in the implementation of nanoscale light emitting devices.     

Properties of optical phonons in Zn1−x−yMgyBexSe quaternary mixed crystal

Long wavelength optical lattice vibration and dielectric constants of the quaternary mixed crystal Zn_1−x−yMg_yBe_xSe are investigated based on the pseudo-unit-cell mode and Born-Huang procedure. It is found that this material shows a three-mode behavior and the oscillator strength of each mode is mainly controlled by only one component. The theoretical results also show that the linear interpretation method for dielectric constants is reliable. The vibrational frequencies and the oscillator strengths of the ternary mixed crystals Be_xZn_1−xSe, Be_xMg_1−xSe and Mg_xZn_1−xSe are also calculated as special cases of the quaternary mixed crystal for comparing with experiments. The calculation shows agreement with the experimental results.     

Optical properties of MgxZn1−xO thin films deposited on silicon and sapphire substrate by rf magnetron sputtering

The index dispersion at UV–VIS range for polycrystalline Mg_xZn_1−xO films on silicon with different Mg concentration was obtained by spectroscopic ellipsometry (SE) method. It decreases with the increase of the Mg content. Above the relative peak wavelength, they are well fitted by the first-order Sellmeier relation. The band gap of films on sapphire of different Mg content was determined from transmission measurements. Photoluminescence (PL) illustrated that for Mg_xZn_1−xO films every PL peak corresponded to a special excitation wavelength. The wavelength of the PL peak was proportional to the special excitation wavelength. A strong peak was obtained in the blue band for the films due to the large amount of oxygen vacancies caused by excess Zn and Mg atoms, while weak peak at ultraviolet band.     

Influence of Co doping content on its valence state in Zn1−xCoxO (0 ≤ x ≤ 0.15) thin films

Zn_1−xCo_xO (0 ≤ x ≤ 0.15) thin films grown on Si (1 0 0) substrates were prepared by a sol-gel technique. The effects of Co doped on the structural, optical properties and surface chemical valence states of the Zn_1−xCo_xO (0 ≤ x ≤ 0.15) films were investigated by X-ray diffraction (XRD), ultraviolet-visible spectrometer and X-ray photoelectron spectroscopy (XPS). XRD results show that the Zn_1−xCo_xO films retained a hexagonal crystal structure of ZnO with better c-axis preferred orientation compared to the undoped ZnO films. The optical absorption spectra suggest that the optical band-gap of the Zn_1−xCo_xO thin films varied from 3.26 to 2.79 eV with increasing Co content from x = 0 to x = 0.15. XPS studies show the possible oxidation states of Co in Zn_1−xCo_xO (0 ≤ x ≤ 0.05), Zn_0.90Co_0.10O and Zn_0.85Co_0.15O are CoO, Co₃O₄ and Co₂O₃, with an increase of Co content, respectively.