Structural characterization of nickel-titanium film on silicon carbide

The presented work describes behavior of contact structures of Ni/Ti type on 6H-SiC n-type. The best contact resistivity obtained is 3.3 × 10⁻⁴ Ω cm². The structure showed excellent thermal stability, it was stable after being tested for 10 h at 900 °C. XRD analysis after annealing at 960 °C revealed orthorhombic Ni₂Si as the dominate phase.     

Rapid thermal annealing induced changes on the contact of Ni/Au to N-doped ZnO

N-doped p-type ZnO (p ∼ 10¹⁸cm^-3) was grown on sapphire(0 0 0 1) substrate by metal-organic chemical vapor deposition method. Ni/Au metal was evaporated on the ZnO film to form contacts. As-deposited contacts were rectifying while ohmic behavior was achieved after thermally annealing the contacts in nitrogen environment. Specific contact resistance was determined by circular transmission line method and a minimum specific contact resistance of 8 × 10⁻⁴ Ω cm² was obtained for the sample annealed at 650 °C for 30 s. However, Hall effect measurements indicate that, as the rapid thermal annealing temperature increased up to 550 °C or higher the samples’ conductive type have changed from p-type to n-type, which may be due to the instability nature of the present-day p-type N-doped ZnO or the dissociation of ZnO caused by annealing process in N₂ ambient. Evolution of the sample's electric characteristics and the increment of metal/semiconductor interface states induced by rapid thermal annealing process are supposed to be responsible for the improvement of electrical properties of Au/Ni/ZnO.     

Electrical, structural and surface morphological properties of thermally stable low-resistance W/Ti/Au multilayer ohmic contacts to n-type GaN

A W/Ti/Au multilayer scheme has been fabricated for achieving thermally stable low-resistance ohmic contact to n-type GaN (4.0 × 10¹⁸ cm⁻³). It is shown that the as-deposited W/Ti/Au contact exhibits near linear I-V behaviour. However, annealing at temperature below 800 °C the contacts exhibit non-linear behaviour. After annealing at a temperature in excess of 850 °C, the W/Ti/Au contact showed ohmic behaviour. The W/Ti/Au contact produced specific contact resistance as low as 6.7 × 10⁻⁶ Ω cm² after annealing at 900 °C for 1 min in a N₂ ambient. It is noted that the specific contact resistance decreases with increase in annealing temperature. It is also noted that annealing the contacts at 900 °C for 30 min causes insignificant degradation of the electrical and thermal properties. It is further shown that the overall surface morphology of the W/Ti/Au stayed fairly smooth even after annealing at 900 °C. The W/Ti/Au ohmic contact showed good edge sharpness after annealing at 900 °C for 30 min. Based on the Auger electron spectroscopy and glancing angle X-ray diffraction results, possible explanation for the annealing dependence of the specific contact resistance of the W/Ti/Au contacts are described and discussed.     

Ta/Ni/Ta multilayered ohmic contacts on n-type SiC

The interface formation, electrical properties and the surface morphology of multilayered Ta/Ni/Ta/SiC contacts were reported in this study. It was found that the conducting behavior of the contacts so fabricated is much dependent on the metal layer thickness and the subsequent annealing temperature. Auger electron spectroscopy (AES) and X-ray diffraction analyses revealed that Ni₂Si and TaC formed as a result of the annealing. The Ni atoms diffused downward to metal/SiC interface and converted into Ni₂Si layer in adjacent to the SiC substrate. The released carbon atoms reacted with Ta atoms to form TaC layer. Ohmic contacts with specific contact resistivity as low as 3 × 10⁻⁴ Ω cm² have been achieved after thermal annealing. The formation of carbon vacancies at the Ni₂Si/SiC interface, probably created by dissociation of SiC and formation of TaC during thermal annealing, should be responsible for the ohmic formation of the annealed Ta/Ni/Ta contacts. The addition of Ta into the Ni metallization scheme to n-SiC restricted the accumulation of carbon atoms left behind during Ni₂Si formation, improving the electrical and microstructure properties.     

Use of TiB2 diffusion barriers for Ni/Au ohmic contacts on p-GaN

The use of a TiB₂ diffusion barrier for Ni/Au contacts on p-GaN is reported. The annealing temperature (25-950 °C) dependence of ohmic contact characteristics using a Ni/Au/TiB₂/Ti/Au metallization scheme deposited by sputtering were investigated by contact resistance measurements and auger electron spectroscopy (AES). The as-deposited contacts are rectifying and transition to ohmic behavior for annealing at ≥500 °C . A minimum specific contact resistivity of ∼3 × 10⁻⁴ Ω cm⁻² was obtained after annealing over a broad range of temperatures (800-950 °C for 60 s). The contact morphology became considerably rougher at the higher end of this temperature range. AES profiling showed significant Ti and Ni outdiffusion through the TiB₂ at 800 °C. By 900 °C the Ti was almost completely removed to the surface, where it became oxidized. Use of the TiB₂ diffusion barrier produces superior thermal stability compared to the more common Ni/Au, whose morphology degrades significantly above 500 °C.     

ZrB2-based Ohmic contacts to p-GaN

The annealing temperature dependence of contact resistance and layer stability of ZrB₂/Ti/Au and Ni/Au/ZrB₂/Ti/Au Ohmic contacts on p-GaN is reported. The as-deposited contacts are rectifying and transition to Ohmic behavior for annealing at ≥750 °C, a significant improvement in thermal stability compared to the conventional Ni/Au Ohmic contact on p-GaN, which is stable only to <600 °C. A minimum specific contact resistance of ∼2 × 10⁻³ Ω cm⁻² was obtained for the ZrB₂/Ti/Au after annealing at 800 °C while for Ni/Au/ZrB₂/Ti/Au the minimum value was 10⁻⁴ Ω cm⁻² at 900 °C. Auger Electron Spectroscopy profiling showed significant Ti, Ni and Zr out diffusion at 750 °C in the Ni/Au/ZrB₂/Ti/Au while the Ti and Zr intermix at 900 °C in the ZrB₂/Ti/Au. These boride-based contacts show promise for contacts to p-GaN in high temperature applications.     

Origin of ohmic behavior in Ni, Ni2Si and Pd contacts on n-type SiC

Ni, Ni₂Si and Pd contacts were prepared on n-type 4H-SiC and annealed in the temperature range of 750-1150 °C. The annealed contacts were analyzed before and after acid etching, and different features were found in unetched and etched contacts. Carbon left on the SiC surface after the acid etching of Ni₂Si contacts annealed at 960 °C was highly graphitized. In nickel contacts, the graphitization of interface carbon began at 960 °C and increased after annealing at higher temperatures. In palladium contacts, the onset of the interface carbon graphitization was observed after annealing at 1150 °C. For all three types of metallization, the minimal values of contact resistivity were achieved only when the sharp first-order peak at 1585 cm⁻¹ and distinct second-order peak at ∼2700 cm⁻¹ related to the presence of graphitized carbon were detected by Raman spectroscopy after the acid etching of contacts. The properties of unannealed secondary contacts deposited onto etched primary contacts were similar to the properties of the primary contacts unless carbon was selectively etched. The results show that ohmic behavior of Ni-based and Pd contacts on n-type SiC originates from the formation of graphitic carbon at the interface with SiC.     

Thermal stability of Ti/Al/Pt/Au and Ti/Au Ohmic contacts on n-type ZnCdO

The specific contact resistivity and chemical intermixing of Ti/Au and Ti/Al/Pt/Au Ohmic contacts on n-type Zn_0.05Cd_0.95O layers grown on ZnO buffer layers on GaN/sapphire templates is reported as a function of annealing temperature in the range 200-600 °C. A minimum contact resistivity of 2.3 × 10⁻⁴ Ω cm² was obtained at 500 °C for Ti/Al/Pt/Au and 1.6 × 10⁻⁴ Ω cm² was obtained at 450 °C for Ti/Al. These values also correspond to the minima in transfer resistance for the contacts. The Ti/Al/Pt/Au contacts show far smoother morphologies after annealing even at 600 °C, whereas the Ti/Au contacts show a reacted appearance after 350 °C anneals. In the former case, Pt and Al outdiffusion is significant at 450 °C, whereas in the latter case the onset of Ti and Zn outdiffusion is evident at the same temperature. The improvement in contact resistance with annealing is suggested to occur through formation of TiO_x phases that induce oxygen vacancies in the ZnCdO.     

Characteristics of sandwich-structured Al2O3/HfO2/Al2O3 gate dielectric films on ultra-thin silicon-on-insulator substrates

Sandwich-structure Al₂O₃/HfO₂/Al₂O₃ gate dielectric films were grown on ultra-thin silicon-on-insulator (SOI) substrates by vacuum electron beam evaporation (EB-PVD) method. AFM and TEM observations showed that the films remained amorphous even after post-annealing treatment at 950 °C with smooth surface and clean silicon interface. EDX- and XPS-analysis results revealed no silicate or silicide at the silicon interface. The equivalent oxide thickness was 3 nm and the dielectric constant was around 7.2, as determined by electrical measurements. A fixed charge density of 3 × 10¹⁰ cm⁻² and a leakage current of 5 × 10⁻⁷A/cm² at 2 V gate bias were achieved for Au/gate stack /Si/SiO₂/Si/Au MIS capacitors. Post-annealing treatment was found to effectively reduce trap density, but increase in annealing temperature did not made any significant difference in the electrical performance.     

Low temperature fabrication of 5-10 nm SiO2/Si structure using advanced nitric acid oxidation of silicon (NAOS) method

We have developed the advanced nitric acid oxidation of Si (NAOS) method to form relatively thick (5-10 nm) SiO₂/Si structure with good electrical characteristics. This method simply involves immersion of Si in 68 wt% nitric acid aqueous solutions at 120 °C with polysilazane films. Fourier transform infrared absorption (FT-IR) measurements show that the atomic density of the NAOS SiO₂ layer is considerably high even without post-oxidation anneal (POA), i.e., 2.28 × 10²² atoms/cm², and it increases by POA at 400 °C in wet-oxygen (2.32 × 10²² atoms/cm²) or dry-oxygen (2.30 × 10²² atoms/cm²). The leakage current density is considerably low (e.g., 10⁻⁵ A/cm² at 8 MV/cm) and it is greatly decreased (10⁻⁸ A/cm² at 8 MV/cm) by POA at 400 °C in wet-oxygen. POA in wet-oxygen increases the atomic density of the SiO₂ layer, and decreases the density of oxide fixed positive charges.     

W2B-based ohmic contacts to n-GaN

Ohmic contact formation on n-GaN using a novel Ti/Al/W₂B/Ti/Au metallization scheme was studied using contact resistance, scanning electron microscopy and Auger electron spectroscopy measurements. A minimum specific contact resistivity of 7 × 10⁻⁶ Ω cm² was achieved at an annealing temperature of 800 °C. The contact resistance was essentially independent of measurement temperature, indicating that field emission plays a dominant role in the current transport .The Ti began to outdiffuse to the surface at temperatures of ∼500 °C, while at 800 °C the Al also began to intermix within the contact. By 1000 °C, the contact showed a reacted appearance and AES showed almost complete intermixing of the metallization. The contact resistance showed excellent stability for extended periods at 200 °C, which simulates the type of device operating temperature that might be expected for operation of GaN-based power electronic devices.     

Annealing temperature dependence of Raman scattering in Si/SiO2 superlattice prepared by magnetron sputtering

Si/SiO₂ superlattices were prepared by magnetron sputtering, and the deposition temperature and annealing temperature had a great influence on the superlattice structure. In terms of SEM images, the mean size of Si nanocrystals annealed at 1100 °C is larger than that of nanocrystals annealed at 850 °C. It was found that the films deposited at room temperature are amorphous. With increasing deposition temperature, the amorphous and crystalline phases coexist. With increasing annealing temperature, the Raman intensity of the peak near 470 cm⁻¹ decreases, and the intensity of that at 520 cm⁻¹ increases. Also, on increasing the annealing temperature, the Raman peak near 520 cm⁻¹ shifts and narrows, and asymmetry emerges. A spherical cluster is used to model the nanocrystals in Si/SiO₂ superlattices, and the observed Raman spectra are analyzed by combining the effects of confinement on the phonon frequencies. Raman spectra from a variety of nanocrystalline silicon structures were successfully explained in terms of the phonon confinement effect. The fitted results agreed well with the experimental observations from SEM images.     

The electrical properties of metal-oxide-semiconductor devices fabricated on the chemically etched n-InP substrate

The electrical properties of the Cu/n-InP and Al/n-InP Schottky barrier diodes (SBDs) with and without the interfacial oxide layer have been investigated by using current-voltage (I-V) measurements. The oxide layer on chemically cleaned indium phosphide (InP) surface has been obtained by exposure to water vapor at 1 ml/min at 200 °C before metal evaporation. The chemical composition of surface oxides grown on the InP is investigated using X-ray photoelectron spectroscopy (XPS). Phosphorus is present as In(PO₃)₃, InPO₄, P₂O₅ and P₄O₁₀. The values of 0.437 ± 0.007 and 0.438 ± 0.003 eV for the barrier height of the reference Cu/n-InP and Al/n-InP SBDs were obtained, respectively. Furthermore, the values of 0.700 ± 0.030 and 0.517 ± 0.023 eV for the barrier height of the oxidized Cu/n-InP and Al/n-InP SBD were obtained, respectively. The transport properties of the metal-semiconductor contacts have been observed to be significantly affected by the presence of the interfacial oxide layer. Devices built on the oxidized surfaces show improved characteristics compared with those built on chemically cleaned surfaces. The chemical reactivity of the metal with oxide and n-InP is important to the formation of the Schottky barriers. The reactive metal Al gave a low barrier height due to the reduction of oxide and reaction with InP. The transmission coefficients for the oxidized Cu/n-InP and Al/n-InP are equal to 2.23 × 10⁻⁵ and 4.60 × 10⁻², respectively.     

Low-resistance Cr/Al Ohmic contacts to N-polar n-type GaN for high-performance vertical light-emitting diodes

We investigated the electrical properties of Cr(30 nm)/Al(200 nm) contacts to N-polar n-type GaN for high-performance vertical light-emitting diodes and compare them with those of Ti(30 nm)/Al(200 nm) contacts. Before annealing, both the samples show ohmic behaviors with a contact resistivity of 1.9-2.3 × 10⁻⁴ Ωcm². Upon annealing at 250 °C for 1 min in N₂ ambient, the Ti/Al contacts become non-ohmic, while the Cr/Al contacts remain ohmic with a contact resistivity of 1.4 × 10⁻³ Ωcm². Based on X-ray photoemission spectroscopy and secondary ion mass spectrometry results, ohmic formation and degradation mechanisms are briefly described and discussed.     

Current-voltage characteristics of Au/GaN/GaAs structure

Au/GaN/n-GaAs structure has been fabricated by the electrochemically anodic nitridation method for providing an evidence of achievement of stable electronic passivation of n-doped GaAs surface. The change of the electronic properties of the GaAs surface induced by the nitridation process has been studied by means of current-voltage (I-V) characterizations on Schottky barrier diodes (SBDs) shaped on gallium nitride/gallium arsenide structure. Au/GaN/n-GaAs Schottky diode that showed rectifying behavior with an ideality factor value of 2.06 and barrier height value of 0.73 eV obeys a metal-interfacial layer-semiconductor (MIS) configuration rather than an ideal Schottky diode due to the existence of GaN at the Au/GaAs interfacial layer. The formation of the GaN interfacial layer for the stable passivation of gallium arsenide surface is investigated through calculation of the interface state density N_ss with and without taking into account the series resistance R_s. While the interface state density calculated without taking into account R_s has increased exponentially with bias from 2.2×10¹² cm⁻² eV⁻¹ in (E_c−0.48) eV to 3.85×10¹² cm⁻² eV⁻¹ in (E_c−0.32) eV of n-GaAs, the N_ss obtained taking into account the series resistance has remained constant with a value of 2.2×10¹² cm⁻² eV⁻¹ in the same interval. This has been attributed to the passivation of the n-doped GaAs surface with the formation of the GaN interfacial layer.     

Correlation between impurities in Fe-Si amorphous layers synthesized by Fe implantation and photoluminescence property of β-FeSi2 precipitates in Si

Completely amorphous Fe-Si layers are formed by Fe implantation into Si substrate at a dosage of 5×10¹⁵ cm⁻² using a metal vapor vacuum arc (MEVVA) ion source under 80 kV extraction voltage and cryogenic temperature. After thermal annealing, β-FeSi₂ precipitates are formed in Si matrix. The influence of impurities in these amorphous Fe-Si layers on the photoluminescence (PL) from β-FeSi₂ precipitates is investigated. PL is found to be significantly enhanced by optimizing the impurity concentration and annealing scheme. After 60 s of rapid thermal annealing (RTA) at 900 °C, β-FeSi₂ precipitates in medium boron-doped Si substrate give the strongest PL intensity without boron out-diffusion from them.     

Investigation of p-type behavior in Ag-doped ZnO thin films by E-beam evaporation

Ag-doped ZnO (ZnO:Ag) thin films were grown on glass substrates by E-beam evaporation technique. The structural, electrical and optical properties of the films were investigated as a function of annealing temperature. The films were subjected to post annealing at different temperatures in the range of 350-650 °C in an air ambient. All the as grown and annealed films at temperature of 350 °C showed p-type conduction. The films lost p-type conduction after post annealing treatment temperature of above 350 °C, suggesting a narrow post annealing temperature window for the fabrication of p-type ZnO:Ag films. ZnO:Ag film annealed at 350 °C revealed lowest resistivity of 7.25 × 10⁻² Ω cm with hole concentration and mobility of 5.09 × 10¹⁹ cm⁻³ and 1.69 cm²/V s, respectively. Observation of a free-to-neutral-acceptor (e,A^o) and donor-acceptor-pair (DAP) emissions in the low temperature photoluminescence measurement confirms p-type conduction in the ZnO:Ag films.     

Improving p-type contact characteristics by Ni-assisted annealing and effects on surface morphologic evolution of InGaN LED films grown on Si (1 1 1)

Ni thin layer was deposited to assist to activate p-GaN and then was removed. The process was named Ni-assisted annealing (NA). We investigate the surface morphology and p-type contact behaviors of InGaN LED films grown on Si (1 1 1) substrates. Compared with conventional thermal annealing (TA), NA can improve the p-type contact characteristic at lower anneal temperature and a smaller specific contact resistivity (ρ_c = 6.1 × 10⁻⁵ Ω cm²) employing nonalloy Pt electrode was obtained. A wet etching method using acid-hydrogen peroxide was adopted to boil films surface after activation. We found that some nano-pits appeared on surfaces while original surface step structure was still clearly visible, which shows a defect-selective etching characteristic. Otherwise, we demonstrated that the surface morphology could be affected by NA while independent to TA. Some mechanisms for experimental phenomena were also discussed in the letter.     

The barrier height inhomogeneity in Al/p-Si Schottky barrier diodes with native insulator layer

The current-voltage (I-V) characteristics of Al/p-Si Schottky barrier diodes (SBDs) with native insulator layer were measured in the temperature range of 150-375 K. The estimated zero-bias barrier height Φ_B0 and the ideality factor n assuming thermionic emission (TE) theory show strong temperature dependence. Evaluation of the forward I-V data reveals an increase of zero-bias barrier height Φ_B0 but decrease of ideality factor n with increase in temperature. The conventional Richardson plot exhibits non-linearity below 250 K with the linear portion corresponding to activation energy of 0.41 eV and Richardson constant (A^*) value of 1.3 × 10⁻⁴ A cm⁻² K⁻² is determined from intercept at the ordinate of this experimental plot, which is much lower than the known value of 32 A cm² K² for holes in p-type Si. Such behavior is attributed to Schottky barrier inhomogene ties by assuming a Gaussian distribution of barrier heights (BHs) due to barrier height inhomogeneities that prevail at interface. Also, Φ_B0 versus q/2kT plot was drawn to obtain evidence of a Gaussian distribution of the BHs, and values of Φ_B0 = 1.055 eV and σ₀ = 0.13 V for the mean BH and zero-bias standard deviation have been obtained from this plot, respectively. Thus, the modified versus q/kT plot gives Φ_B0 and A^* as 1.050 eV and 40.08 A cm⁻² K⁻², respectively, without using the temperature coefficient of the barrier height. This value of the Richardson constant 40.03 A cm⁻² K⁻² is very close to the theoretical value of 32 A K⁻² cm⁻² for p-type Si. Hence, it has been concluded that the temperature dependence of the forward I-V characteristics of the Al/p-Si Schottky barrier diodes with native insulator layer can be successfully explained on the basis of TE mechanism with a Gaussian distribution of the barrier heights.     

Auger electron spectroscopy of Au/NiOx contacts on p-GaN annealed in N2 and O2 + N2 ambients

We have designed a promising contact scheme to p-GaN. Au/NiO_x layers with a low concentration of O in NiO_x are deposited on p-GaN by reactive dc magnetron sputtering and annealed in N₂ and in a mixture of O₂ + N₂ to produce low resistivity ohmic contacts. Annealing has been studied of NiO_x layers with various contents of oxygen upon the electrical properties of Au/NiO_x/p-GaN. It has been found that the Au/NiO_x/p-GaN structure with a low content of oxygen in NiO_x layer provides a low resistivity ohmic contact even after subsequent annealing in N₂ or O₂ + N₂ ambient at 500 °C for 2 min.Auger depth profiles and transmission electron microscopy (TEM) micrographs reveal that while annealing in O₂ + N₂ ambient results in reconstruction of the initial deposited Au/NiO_x/p-GaN contact structure into a Au/p-NiO/p-GaN structure, annealing in N₂ brings about reconstruction into Au/p-NiO/p-GaN and Ni/p-NiO/p-GaN structures. Hence, in both cases, after annealing in N₂ as well as in O₂ + N₂ ambient, the ohmic properties of the contacts are determined by creation of a thin oxide layer (p-NiO) on the metal/p-GaN interface. Higher contact resistivities in the samples annealed in O₂ + N₂ ambient are most likely caused by a smaller effective area of the contact due to creation of voids.