Fabrication and scanning tunneling microscopy studies of the Si(1 1 1)-(√31 × √31)-In surface

We report on the fabrication of single phase of the Si(1 1 1)-(√31 × √31)-In reconstruction surface, observed by scanning tunneling microscopy (STM) at room temperature. By depositing specific amounts of indium atoms while heating the Si(1 1 1)-(7 × 7) substrate at a critical temperature, the single phase of Si(1 1 1)-(√31 × √31)-In surfaces could be routinely obtained over the whole surface with large domains. This procedure is certified by our high-resolution STM images in the range of 5-700 nm. Besides, the high resolution STM images of the Si(1 1 1)-(√31 × √31)-In surface were also presented.     

Observation of Si(1 0 0) surfaces annealed in hydrogen gas ambient by scanning tunneling microscopy

We investigated the cleaning process of Si(1 0 0) surfaces by annealing in H₂ gas ambient following chemical treatments by scanning tunneling microscopy. We observed the monohydride Si structure: Si(1 0 0):2 × 1-H on the surfaces annealed at 1000 °C in 2.5 × 10⁴ Pa H₂ gas ambient without conspicuous contaminants. On the sample annealed for 10 min or longer times, well-defined Si(1 0 0) structures with alternating S_A and S_B steps were observed, whereas the initial roughness still remained on the surfaces annealed for only 5 min.     

The structural formation of methylthiolate SAMs on Au(1 1 1) for short deposition times from solution

Scanning tunnelling microscopy was used to investigate the structural formation of methylthiolate self-assembled monolayers on Au(1 1 1). SAMs were prepared by exposing the gold crystal to an ethanol-dimethyldisulfide solution for immersion times of 12 min, 12 h, and 24 h. After preparation the formation of a () rect. striped phase was found. For this phase, the immersion time is the key parameter determining the size and number of ordered domains. Annealing induced a phase transition leading to large domains in a (3×4) structure. The annealing temperature determines whether a mixed phase of both structures or only the (3×4) structure are formed. We find no influence of the immersion time on the formation of the second structure. A structure model is presented for both phases on the basis on the same building block containing two methylthiolate molecules and a gold ad-atom.     

Ordered thin films of alkyloxy-substituted benzaldehydes on a graphite surface studied by scanning tunneling microscopy

The molecular assembly of three different trialkyloxy-substituted benzaldehydes on graphite has been studied using scanning tunneling microscopy (STM). It is found that these benzaldehydes, which do not have intermolecular hydrogen bonding, could form a lamella arrangement in which the headgroups are aligned side by side. The effect due to the alkyl chain length on the lamella structure is also presented. Received: 21 January 2002 / Accepted: 22 March 2002 / Published online: 10 September 2002 RID="*" ID="*"Corresponding author. Fax: +86-10/6255-7908     

Oxidation of graphene on Ru(0 0 0 1) studied by scanning tunneling microscopy

The oxidation of graphene layer on Ru(0 0 0 1) has been investigated by means of scanning tunneling microscopy. Graphene overlayer can be formed by decomposing ethyne on Ru(0 0 0 1) at a temperature of about 1000 K. The lattice mismatch between the graphene overlayer and the substrate causes a moiré pattern with a superstructure in a periodicity of about 30 Å. The oxidation of graphene/Ru(0 0 0 1) was performed by exposure the sample to O₂ gas at 823 K. The results showed that, at the initial stage, the oxygen intercalation between the graphene and the Ru(0 0 0 1) substrate takes place at step edges, and extends on the lower steps. The oxygen intercalation decouples the graphene layer from the Ru(0 0 0 1) substrate. More oxygen intercalation yields wrinkled bumps on the graphene surface. The oxidation of graphene, or the removal of carbon atoms can be attributed to a process of the combination of the carbon atoms with atomic oxygen to form volatile reaction products. Finally, the Ru(0 0 0 1)-(2 × 1)O phase was observed after the graphene layer is fully removed by oxidation.     

Growth of copper phthalocyanine on hydrogen passivated vicinal silicon(1 1 1) surfaces

Using ultra-high vacuum scanning tunneling microscopy (UHV-STM), we show that copper-phthalocyanine (CuPc) grows in a well ordered manner on hydrogen passivated vicinal silicon surfaces. CuPc grows one-dimensionally parallel to the monatomic steps on the vicinal silicon surface. Surprisingly, elongated clusters of the CuPc parallel to the step directions are formed even on the middle of the terraces well away from the step edges. The one-dimensional growth mode continues even after the full monolayer coverage on the substrate which results in strongly oriented growth mode of a thin film of CuPc on the vicinal silicon surfaces.     

SR-PES and STM observation of metastable chemisorption state of oxygen on Si(1 1 0)-16 × 2 surface

Initial adsorption of oxygen molecules on the Si(1 1 0)-16 × 2 surface and subsequent modification of the bonding states induced by mild (300 °C) annealing have been studied by synchrotron-radiation photoemission spectroscopy and scanning-tunneling microscopy. It has been shown that upon annealing, the intensity and the energy positions of the Si 2p suboxide components shift towards the values characteristic for the thermal oxide. This indicates the presence of a metastable chemisorption state of oxygen on the Si(1 1 0)-16 × 2 surface.     

Indium-induced superstructures formed on Si(1 1 0) surfaces

Si(1 1 0) surfaces covered with small amounts of In deposit and then annealed at high temperature were investigated by RHEED, and two kinds of superstructures with A = 3a and B = −a + 4b, and A = 3a − 2b and B = −2a + 4b as primitive translational vectors are reported to form on the surfaces.     

Pd adsorption on Si(1 1 3) surface: STM and XPS study

Pd-induced surface structures on Si(1 1 3) have been studied by scanning tunneling microscopy (STM) and X-ray photoelectron spectroscopy (XPS). In the initial process of the Pd adsorption below 0.10 ML, Pd silicide (Pd₂Si) clusters are observed to form randomly on the surface. By increasing the Pd coverage to 0.10 ML, the clusters cover the entire surface, and an amorphous layer is formed. After annealing the Si(1 1 3)-Pd surface at 600 °C, various types of islands and chain protrusions appears. The agglomeration, coalescence and crystallization of these islands are observed by using high temperature (HT-) STM. It is also found by XPS that the islands correspond to Pd₂Si structure. On the basis of these results, evolution of Pd-induced structures at high temperatures is in detail discussed.     

Stable reconstruction and adsorbates of InAs(1 1 1)A surface

We investigated the surface properties of InAs(1 1 1)A by low-temperature scanning tunneling microscopy (LT-STM) with atomic resolution and first-principles calculation. Very clear atom image was observed, showing that the surface reconstruction is an In-vacancy structure. We also observed two kinds of adsorbates on the surface. The first-principles calculations indicate that the In-vacancy structure is the most stable surface reconstruction under any experimental conditions, which is consistent with the LT-STM observation. Investigations of adsorption properties of an In atom, an As atom, and an As₂ molecule by the first-principles calculations imply that the observed adsorbates are an In atom and an As₂ molecule.     

Quasi-one-dimensional structures on the Si(1 1 1) surface induced by Ba adsorption

Ba-induced quasi-one-dimensional reconstructions of the Si(1 1 1) surface have been investigated by low energy electron diffraction (LEED) and scanning tunneling microscopy (STM). While the 3 × ‘2’ surface shows double-periodicity along the stripes in STM images consistent with half-order streaks observed in LEED patterns, no sign of the double-periodicity along the chain direction was detected for the 5 × 1 surface. The 5× stripes in STM images show internal structures with multiple rows. The two rows comprising the boundaries of a 5× stripe in the filled-state STM image are found to have 3a × √3/2 spacing across the stripe. The observation of the successive 3× and 2× spacings between the boundary rows supports a structural model proposed for the Ba-induced 5 × 1 Si reconstruction composed of honeycomb chains and Seiwatz chains. The highest coverage 2 × 8 surface does not reveal a quasi-1D row structure in STM images.     

Quasi-one-dimensional In atomic chains on Si(1 1 1) at low temperature studied by reflection high-energy positron diffraction and scanning tunneling microscopy

We have investigated a quasi-one-dimensional structure of Si(1 1 1)-8 × 2-In surface using reflection high-energy positron diffraction (RHEPD) and scanning tunneling microscopy (STM). From the RHEPD rocking curve analyses, we confirmed the formation of the In hexagon structure proposed by González et al. [C. González, F. Flores, J. Ortega, Phys. Rev. Lett. 96 (2006) 136101]. Furthermore, we found that the empty-state STM image at 44 K is consistent with that calculated with the optimum hexagon structure by the RHEPD analyses.     

Adsorption of Al on the Si(0 0 1) surface

The first-principles calculations have been presented to study the adsorption of aluminum (Al) on the Si(0 0 1)(2×1) surface. We have investigated the optimized geometries and electronic structures of the adatom-substrate system. The adsorption energy of the system has been calculated. The most stable adsorption sites were consequently determined to be HH site and T3+T4. It is shown that the Si-Si dimer is asymmetric on the reconstructed bare surface and become symmetric upon Al adsorption. In addition, the bond length of Si-Si was found to be considerably elongated in the adsorption system. It is found that the work function change obtained in our work is different from other previous results on the adsorption of alkali metals on the Si(0 0 1) surface. In order to investigate the relative stability of phases at different coverages, the surface formation energy of the adsorption system was calculated. To shed light on the nature of the Al-Si bond and the character of silicon surface, the density of states (DOS) and difference charge density of the system were evaluated.     

Hydrogen-induced metallization on Ge(1 1 1) c(2 × 8)

We have studied hydrogen adsorption on the Ge(1 1 1) c(2 × 8) surface using scanning tunneling microscopy (STM) and angle-resolved photoelectron spectroscopy (ARPES). We find that atomic hydrogen preferentially adsorbs on rest atom sites. The neighbouring adatoms appear higher in STM images, which clearly indicates a charge transfer from the rest atom states to the adatom states. The surface states near the Fermi-level have been followed by ARPES as function of H exposure. Initially, there is strong emission from the rest atom states but no emission at the Fermi-level which confirms the semiconducting character of the c(2 × 8) surface. With increasing H exposure a structure develops in the close vicinity of the Fermi-level. The energy position clearly indicates a metallic character of the H-adsorbed surface. Since the only change in the STM images is the increased brightness of the adatoms neighbouring a H-terminated rest atom, we identify the emission at the Fermi-level with these adatom states.     

Adsorption structure of germanium on the Ru(0 0 0 1) surface

Coverage-dependent adsorption energy of the Ge/Ru(0 0 0 1) growth system and the geometrical distortions of the most stable adsorption structure are investigated through first-principles calculations within density functional theory. A local minimum in adsorption energy is found to be at a Ge coverage of 1/7 monolayer with a Ru(0 0 0 1)- symmetry. Based on this stale superstructure, the scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS) images are simulated by means of surface local-density of states (LDOS). The results are consistent well with the STM measurements on the phase for Ge overlayer on Ru(0 0 0 1). From this stimulation, the relations between the STM images and the lattice distortion are also clarified.     

Barrier height imaging of Si(1 1 1)3 × 1-Ag reconstructed surfaces

We investigated the bias voltage polarity dependence of atomically resolved barrier height (BH) images on Si(1 1 1)3 × 1-Ag surfaces. The BH images were very similar to scanning tunneling microscopy (STM) images in both the empty and filled states. This similarity strongly supports the interpretation that the BH image reflects the vertical decay rate of the surface local density of states (LDOS). Differences in contrast and protrusion shapes between BH and STM images were observed. We attributed these differences to the geometric contribution to the STM image and to the improved spatial resolution of the BH image due to the lock-in technique.     

Atomic structure of the carbon induced Si(0 0 1)-c(4 × 4) surface

The atomic and electronic structures of the Si(0 0 1)-c(4 × 4) surface have been studied by scanning tunneling microscopy (STM) and density functional theory (DFT). To explain the experimental bias dependent STM observations, a modified mixed ad-dimer reconstruction model is introduced. The model involves three tilted Si dimers and a carbon atom incorporated into the third subsurface layer per c(4 × 4) unit cell. The calculated STM images show a close resemblance to the experimental ones.     

Morphology of pentacene films deposited on Cu(1 1 9) vicinal surface

We investigate the morphology of a pentacene (C₂₂H₁₄) film adsorbed on the Cu(1 1 9) vicinal surface by scanning tunnelling microscopy (STM). Thermal treatment of a thick film of molecules generates a long-range ordered structure. Series of molecular rows are alternated with areas where the molecules assume two equivalent orientations. STM data analysis suggests that the ordered structure can be described by a rippled morphology. The behaviour of the film at different annealing temperatures suggests a possible explanation of the film structure as due to an adsorbate-induced modification of the substrate.     

Scanning tunneling microscopy observation of initial growth of Sn and Ge1−xSnx layers on Ge(0 0 1) substrates

We have investigated the initial growth of Sn and Ge_1−xSn_x layers on Ge(0 0 1) surface by using scanning tunneling microscopy. After the growth of a 0.035 ML-thick Sn layer at room temperature, Sn clusters lining vertically to a dimer row was observed. In the case of the 0.035-0.018 ML-thick Sn growth at 250 °C, the characteristic surface reconstruction with the step-edge undulation like a comb was observed. In the growth of a Ge_0.994Sn_0.006 layer at 250 °C, the multilayer polynuclear growth with a lot of two-dimensional small domain was observed. These surface reconstructions should be accounted for by the large compressive stress induced in the surface layer due to the incorporation of Sn atoms.     

STM study of the initial stages of C60 adsorption on the Pt(1 1 0)-(1 × 2) surface

We have studied the initial stages of adsorption of C₆₀ on the Pt (1 1 0)-(1 × 2) surface by means of STM. At room temperature, fullerene molecules adsorb in the troughs between two adjacent Pt rows of the missing row reconstruction. Mobility over the terraces is negligible, denoting strong bonding with the surface, also testified by a well-defined orientation of fullerene monomers with respect to the substrate. Upon annealing at 750 K, molecular migration towards kinks and step edges occurs, where small islands nucleation begins. A commensurate registry with the substrate is maintained by small (5-10 molecules) C₆₀ aggregates, leading to expanded nearest-neighbour distances with respect to those found in hexagonal close packed fullerene ad-islands grown on other metallic substrates.