Maximum number of connectable laser diode optical switch (LDSW) systems

The maximum number of connectable laser diode optical switches (LDSWs) was studied through the baseband signal-to-noise ratio calculation. For an NRZ 100 Mbits^–1 PCM-IM signal, 60 stages of LDSWs can be connected with a 6-nm optical bandpass filter inserted after the last stage at an input signal level of –30 dB m and an internal gain of 16 dB. A PCM-IM signal of 10 Gbits^–1 can be transmitted through 130 stages of LDSWs at an internal gain of 8 dB and an input signal level of –20 dB m.     

Amplifying Characteristics of Er3+/Yb3+ Co-Doped Parallel-Cascaded Double Microring Resonators

Abstract

In terms of the coupled mode theory, formulas of the transfer function and the output power gain are presented for an Er³⁺/Yb³⁺ co-doped parallel-cascaded double microring resonator. Around the pump wavelength of 0.98 μm and the central signal wavelength of 1.55 μm, analysis is performed for the dependence of the output power gain on the pump power, signal power, dopant concentration, amplitude coupling ratio, and ring spacing. The results show that the output power gain of this device is much larger than that of the Er³⁺/Yb³⁺ co-doped waveguide amplifier with identical waveguide lengths. In the case of the amplitude coupling ratio κ = 0.064, ring spacing L₂ = 10π R, pump power P_p0 = 8 mW, signal power P_s0 = 37.2 μW, Er³⁺ ion concentration N_Er = 1 × 26 m^?3, and Yb³⁺ ion concentration N_Yb = 3 × 27 m^?3, the device can produce higher signal power gain from 11.9 dB even up to 70 dB.     

980nm泵浦的掺铒光纤放大器实验研究

10m长的铒掺杂光纤在980nm波长半导体激光器泵浦下,获得了对1.55μm波长的入射光信号的放大作用。当入射光信号功率为-22dBm而泵浦功率为9.3mW时,放大器的增益为15dB.     

20-Gb/s and Higher Bit Rate Optical Wavelength Conversion for RZ-DPSK Signal Based on Four-Wave Mixing in Semiconductor Optical Amplifier

Abstract

We investigate 20 Gb/s wavelength conversion for return-to-zero differential phase-shift keying (RZ-DPSK) signal using four-wave mixing (FWM) in a semiconductor optical amplifier (SOA). We show that the 10-Gb/s RZ-DPSK signal-to-pump ratio increases up to ?0.286 dB with Q factor improvement of 1.663 dB for increasing the cascadeability of optical networks. The effect of variation in bandwidth for an ideal dual-arm Mach-Zehnder interferometer (MZI) is illustrated. For different bit rates, the converted power signal is investigated with increase in signal input power. We show that the quality of converted signal is best before the saturation of SOA. The dependence of four-wave mixing (FWM) efficiency and converted signal power with signal input power is also studied, and it is found that FWM efficiency decreases with increase in signal input power.

The impact of signal-to–pump power ratio, unsaturated amplifier gain, and pump power is further optimized with minimum Q factor penalty for 10-Gb/s and 20-Gb/s bit rate. We show that converted signal power increases up to power saturation level and then starts decreasing. We also show that with higher bit rate, we have a wide range of choices for pump power signal. We further investigate the quality of converted signal at 10 Gb/s, which shows an improvement over signal input power. Finally, the increase in transmission distance after wavelength conversion is investigated.     

Supercontinuum generation at 1.55μm using highly nonlinear photonic crystal fiber for telecommunication and medical applications

In this paper, we present a theoretical calculation of a highly nonlinear germanium (Ge) doped photonic crystal fiber with all-normal group velocity dispersion to design a supercontinuum (SC) light source at 1.55 μm. By doping 3% higher refractive index Ge inside the host silica, the nonlinear coefficient is increased to a value as large as 60.5 W^?1 km^?1 at 1.55 μm. A 10 dB bandwidth of a 120 nm SC spectrum for a 2.5 ps input optical pulse and a 10 dB bandwidth of a 190 nm SC spectrum for a 1.0 ps input optical pulse have been found using the same fiber length of 200m and input optical power of 18 W. The coherent lengths of the generated SC light sources are found to be 8.8 μm for a 2.5 ps input optical pulse and 5.6 μm for a 1.0 ps input optical pulse. Therefore, the highest longitudinal resolution at 1.55 μm is found to be about 4.0 μm for biological tissues.     

长波段掺铒光纤放大器用掺铒光纤的设计考虑

本文分析了长波段掺铒光纤放大器(EDFA)的增益系数与Er³⁺离子浓度的关系.研制了铝共掺杂的高浓度掺铒光纤,以缩短长波段掺铒光纤的长度.用两级泵浦实现了L-波段EDFA.光纤放大器的掺铒光纤总长18m,在1570nm波长处的小信号增益为42.26dB,输出功率为17.5dBm.我们认为,较低的浓度淬灭效应归因于光纤中较高的A1掺杂浓度.当总的输入信号功率为-3dBm时,在1570至1600nm间的7路WDM信号的增益不平坦度仅为0.68dB..     

基于非线性光纤环形镜的少模脉冲幅度调制再生器

随着网络带宽需求的快速增加,波分复用系统的容量已接近非线性香农极限.为了适应未来网络的发展,空分复用技术引起了越来越多的关注.本文首次提出基于少模非线性光纤环形镜(FM-NOLM)的脉冲幅度调制(PAM)全光再生器,描述了其工作原理和具体设计过程.采用COMSOL软件对组成FM-NOLM的硫化物高非线性光纤进行了模式特性仿真.以LP01,LP11,LP21三个光纤模式为例,确定了再生器的参数,计算出每个模式的功率转移函数曲线.仿真分析了该少模PAM-4全光再生器的噪声抑制(NRR)性能,并与单模情形进行了比较.研究表明,1)对于每个空间模式的PAM信号,所有再生电平具有一致的功率转移性能;2)当输入信噪比(SNR)约大于20 dB时,三种模式的噪声抑制比均可超过3 dB,并随着输入信噪比线性增加,其斜率约为1.2;3)在相同输入SNR条件下,三种模式的噪声抑制比相差不大,不超过1.1 dB.为了说明再生器的再生性能,当输入SNR为25 dB时,我们还给出了再生前后PAM-4信号的功率分布直方图.与现有的再生方案相比,本文方案的均匀多电平再生转移性能,使其更适合高频谱效率的长距空分复用系统和任意电平数的PAM信号再生.此外,该方案也能够扩展到波长域,有效提高光通信系统的传输容量.     

High-gain erbium-doped fiber amplifier incorporating a double-pass amplification technique as a preamplifier

We present a high-gain erbium-doped fiber amplifier to be utilized as a preamplifier. A double-pass amplification technique is used in the first-stage amplifier together with a tunable bandpass filter. The secondstage amplifier is a counter-pumped configuration and another tunable bandpass filter is utilized to filter out amplified spontaneous emission from the first-stage amplifier. This design is able to produce a high gain of 55.6 dB and a noise figure of 6.02 dB at 1530 nm with a signal power of ?45 dBm. The receiver sensitivity measurement shows that the proposed amplifier improves the minimum detectable power from ?33.7 to ?40.8 dBm for a bit-error rate of 10^?11 at 155 Mbps.

     

An efficient electrode arrangement for TWSOA based inline detector

An efficient electrode scheme is developed to enhance the inline detector performance of a 1.55 μm, InP–InGaAsP, Traveling Wave-Semiconductor Optical Amplifier (TW-SOA). A traveling wave approach is used to determine the voltage developed along the length of the TWSOA, accurately. A single electrode along the entire length of the device and a single, short length electrode kept at certain distance from the front facet are investigated, for input optical power levels ranging from −25 dBm to +5 dBm. Efficient position of the single electrode along the cavity length is determined for maximum detected voltage. Under this scheme, the inline detector with an electrode length of 100 μm positioned at 200 μm from the front facet, is found to provide a improvement of 6 dB and 8 dB in detected voltage for 40 mA and 50 mA bias respectively, at −10 dBm input, when compared with the maximum detected voltage reported in the literature.     

The adoption and mechanism of KIO4 for redox-equilibrated stabilization of FeO4 2− as an equalizer in water

The inherent thermodynamic instability of FeO₄ ²⁻ in water restricts its applications in water treatment, battery, and organic synthesis. The objective of this paper was to research and develop an additive for stabilization and mechanism of aqueous FeO₄ ²⁻ solution on the basis of a choice of the redox equilibration. In this study, it was found that FeO₄ ²⁻ in water was stabilized by the right match and adoption of KIO₄ called an equalizer. The redox thermodynamic analysis and dynamic experimental results show that the adoption of KIO₄ equalizer greatly increased lifetime of FeO₄ ²⁻ in water by orders of magnitude. The stabilization mechanism is attributed to occur via the effect of redox equilibrium of the FeO₄ ²⁻ and the IO₄ ⁻ species, as well as the formation of an oxidizing chemical environment. This study opens up possibilities for stabilization of solid ferrate compounds, for example, for use in the water treatment and super-iron battery.

     

40 Gb/s信号全光3R再生实验

提出一种新型40 Gb/s全光3R再生器方案。采用高精细度法布里-珀罗滤波器进行时钟提取。时钟提取前,通过高稳定光源对输入信号光波长变换实现信号光波长和法布里-珀罗滤波器梳状窗口对准;时钟提取后,接半导体光放大器(SOA)进一步消除时钟信号噪声。全光判决中,采用双半导体光放大器串联增大非线性性能,提高了判决门的响应速度。判决输出接窄带滤波器去除脉冲啁啾拖尾,减小码型效应。实验中,恶化40 Gb/s光脉冲信号通过全光3R再生器可以得到再生脉冲。输入恶化信号时间抖动大于5 ps,脉冲宽度大于16 ps,再生得到的信号时间抖动小于1.5 ps。再生信号相对于输入信噪比改善14 dB。连续稳定工作记录大于15 h。通过实验验证,这种全光3R再生器方案成功地实现了40 Gb/s信号的再生。     

Optimization of regenerator based on semiconductor optical amplifier for degraded differential phase shift keying signal

Real time phase regeneration is necessary for degraded phase modulation format optical communication systems.A regenerator based on the discrimitive gain effect of a semiconductor optical amplifier was proposed in recent years.In this paper,for this type of regenerator,its optimal working condition is found by solving the dynamic equations which describe the variance of the optical field and carrier density in the semiconductor optical amplifier by the finite difference method.The results show that the optimal improvement of signal Q factor can reach more than 2.2 dB.     

Yb3+sensitized Er3+-doped waveguide amplifiers: a theoretical approach

Silicate and phosphate glass waveguide amplifiers doped with Er³⁺, and co-doped with Er³⁺/Yb³⁺ are theoretically studied. Configurations for core and core–cladding doped waveguide amplifiers are considered. It is shown that gain in the core–cladding doped amplifiers is considerably higher than core doped amplifiers. It is also shown that with input signal power up to 1 and 200mW pump power, a 12.5dB gain can be achieved in a 3cm long waveguide amplifier, with a noise figure of 3dB.     

10 Gb/s Reconfigurable Optical Logic Gate Using a Single Hybrid-Integrated SOA-MZI

Abstract

A novel reconfigurable Boolean device based on a single Mach-Zehnder interferometer with semiconductor optical amplifiers is demonstrated at 10 Gb/s using intensity return-to-zero modulated signals. The experimental results show that the device can be dynamically reconfigured to operate as a logic XOR, AND, OR, and NOT gate using optical switches. By properly adjusting the input powers, an extinction ratio higher than 10 dB may be obtained. The potential of integration of this architecture makes it an interesting approach in photonic computing and optical signal processing.     

Ultra-long-period fiber grating cascaded to a knob-taper for simultaneous measurement of strain and temperature

This study presents a simple Mach–Zehnder interferometer (MZI) to obtain the bimodal characteristics that realize simultaneous measurement of strain and temperature through cascading an ultra-long-period fiber grating and a knob-shaped taper. We obtain the multi-dip feature from the MZI, and the Dips 2 and 5 are selected from 11 interference dips. Experimental results indicated that the wavelength sensitivities of Dips 2 and 5 are ??0.54 nm mε^?1 and 0.058 nm °C^?1, and ??0.53 nm mε^?1 and 0.055 nm °C^?1 to strain and temperature, respectively. The depth sensitivities are ??3.3 dB mε^??1, ? 0.015 dB °C^?1 and ?5.8 dB mε^?1, and 0.06 dB °C^?1 for Dips 2 and 5, respectively. It is concluded that the proposed structure is suitable for simultaneous strain and temperature measurements.     

Specialty Yb fiber amplifier for microchip Nd laser: Towards ∼1-mJ/1-ns output at kHz-range repetition rate

We demonstrate and optimize, for a mJ/ns release at the wavelength 1.064 μm, the operation of a compact laser system designed in the form of a hybrid, active-passive, Q-switched Nd³⁺:YAG/Cr⁴⁺:YAG microchip laser seeding an Yb-doped specialty multi-port fiber amplifier. As the result of the amplifier optimization, ∼1 mJ, ∼1 ns, almost single-mode pulses at a 1-10-kHz repetition rate are achieved, given by a gain factor of ∼19 dB for an 11-μJ input from the microchip laser. Meanwhile, a lower pulse energy, ∼120 μJ, but a much higher gain (∼25 dB) are eligible for the less powerful (0.35 μJ) input pulses.     

Extinction ratio improvement by an all-optical signal regenerator with a semiconductor optical amplifier and a Sagnac loop

In this paper, we present the operation of an all-optical signal regenerator (AOSR). The AOSR is based on a semiconductor optical amplifier (SOA), which is incorporated in an asymmetric Sagnac loop (ASL). We show experimentally that the AOSR is capable of improving the input signal extinction ratio (ER) considerably. We present a theoretical model, which explains this improvement, and we illustrate a qualitatively similar behavior with a simulation.     

1.55-μm non-anti-reflection-coated fiber grating laser for single-longitudinal mode operation

A 1.55-m fiber grating laser (FGL) was fabricated by optically packaging a non-anti-reflection (AR) coated Fabry–Perot (FP) laser to a lensed fiber grating. The FGL demonstrates a single-longitudinal mode operation with a side-mode suppression ratio (SMSR) of up to 40 dB. The SMSR oscillates and diminishes to <30 dB as the increase of injection current above 38 mA, and the tilt of the fiber approaches 5° away from the facet normal of the FP laser. We have performed numerical simulations on the single-longitudinal mode operation for the FGL. The SMSR for the FGL increases over 40 dB as the increase of the fiber grating reflectivity (R _g) above 0.7 with non-AR-coated FP laser facet. Our calculations also show that the strong current-dependent SMSR oscillation is from the mode selection by the fiber grating external cavity and the heating effect in the FP laser.     

LD-clad-pumped nanosecond Tm<Superscript>3+</Superscript> doped silica fiber amplifier at 1.99 μm

ALD-clad-pumped nanosecond Tm³⁺ doped silica fiber amplifier was reported that provided up to a 2-W average power output with a slope efficiency of 48.6% with respect to the absorbed pumped power. The input signal central wavelength was at 1.99 μm, with a 119.5-ns pulse duration and 5-kHz repeat rates. The pump sources were a 793-nm LD output with a 400-μm pigtail fiber. The gain fiber was D-shaped Tm³⁺ doped silica double-clad fiber with a diameter of 27.5/400 μm. The output amplified pulse and spectrum were in accordance with the input signal. This is the first report to the authors’ knowledge on the general experimental investigation of a LD-clad-pumped Tm³⁺ doped silica nanosecond-fiber amplifier at 1.99 μm.     

Planar microoptical multiplexer and demultiplexer for multimode optical transmission lines

A matching pair of 10-channel planar grating multiplexer/demultiplexer has been numerically analysed and fabricated. Basic construction elements are a planar slab waveguide with a cylindrical mirror facet, a standard plane blazed reflection grating and an array of input/output fibres. The arrangement has proved to work sufficiently well without special measures to reduce aberration such as inclining the input/output facet. The ray tracing method satisfactorily describes the characteristics of the devices. Measured insertion losses range from 2.2 to 7.8 dB, full 1-dB passband widths are 14 nm for the demultiplexer and 25 nm for the multiplexer.On leave from Krone AG, Berlin.