Synthesis and physical properties of TEOS-based silica aerogels prepared by two step (acid–base) sol–gel process

The experimental results on the synthesis and physical properties of tetraethoxysilane- (TEOS) based silica aerogels produced by two step (acid–base) sol–gel process, are reported. The oxalic acid (A) and NH₄OH (B) concentrations were varied from 0 to 0.1 M and from 0.4 to 3 M, respectively. Monolithic and transparent aerogels have been obtained for the values of A=0.001 M and B=1 M. The effect of time interval (t) before the base catalyst (NH₄OH) addition to the acidic sol was studied from 0 to 72 h. The time interval at t=24 h of NH₄OH addition was found to be the best, in terms of low volume shrinkage, high optical transmission and monolithicity. The molar ratio of EtOH/TEOS (S) was varied from 3 to 7.5. Monolithic and transparent aerogels were obtained for an S value of 6.9. Also, the effects of molar ratio of acidic water, i.e., H₂O/TEOS (W₁) and basic water, i.e., H₂O/TEOS (W₂) on the physical properties of the aerogels have been studied. Highly transparent (∼90%) and monolithic aerogels with lower volume shrinkage (<10%) were obtained for the molar ratio 1:6.9:3.5:2.2 of TEOS:EtOH:acidic (H₂O):basic (H₂O). The results are discussed by taking into consideration the hydrolysis and polycondensation reactions. The aerogels were characterized by scanning electron microscopy (SEM), optical transmission, bulk density, volume shrinkage and porosity measurements.     

Titanium dioxide fibers prepared by sol–gel process and centrifugal spinning

A new study of the preparation of nanocrystalline titanium dioxide (TiO₂) fibers is reported in the paper, which were prepared by sol–gel process with titanium acetate [Ti(CH₃COO)₄] as precursor. After that, centrifugal spinning and steam atmosphere heat-treatment were used to obtain final fibers. Here, the molecule structure of precursor was analyzed and the TiO₂ fibers obtained were characterized. Additionally, the effects of the silica (SiO₂) doping were discussed in this paper. By the Fourier transformation infrared spectrum analysis, the chain structure of –O–Ti–O–Ti–O– was confirmed in the Ti(CH₃COO)₄ precursor, as a result the precursor spinning solution showed a good spinning performance. And the pyrolysis process of precursor fibers was analyzed with the help of DSC–TG method. The phase of TiO₂ fibers obtained after heat-treatment with steam atmosphere was characterized mainly by the X-ray diffractometer (XRD), from the XRD curves, the result that the SiO₂ doping can efficiently inhibit the grain growth of TiO₂ fibers could also be verified. The microstructure of the TiO₂ fibers was observed by scanning electron microscope, which showed that diameter of TiO₂ fibers obtained with excellent continuity are from 5 to 10 μm. At last, the photocatalytic property of TiO₂ fibers was also tested.     

Effect of post-treatment (gel aging) on the properties of methyltrimethoxysilane based silica aerogels prepared by two-step sol–gel process

The properties of silica aerogels are highly dependent on the post-treatment steps like gel washing, gel aging and gel drying. The experimental results of the studies on one of the post-treatment steps i.e. gel aging effect on the physical and microstructural properties of methyltrimethoxysilane (MTMS) based silica aerogels, are reported. These hybrid aerogels were prepared by two step sol–gel process followed by supercritical drying. The molar ratio of MeOH/MTMS (M) was varied from 7 to 35 by keeping the H₂O/MTMS (W) molar ratio constant at 4. The as prepared alcogels of different molar ratios were aged from 0 to 5 days. It was observed that 2 days of gel aging period is the optimum gel aging period for good quality aerogels in terms of low density, less volume shrinkage and high porosity. The well tailored network matrix with low density (0.04 g/cm³), less volume shrinkage (4.5%), low thermal conductivity (0.05 W/mK) and high porosity (98.84 %) was obtained for 2 days of gel aging period of M = 35. Further, the gelation time varied from 8 to 1 h depending on the M values. The gelation time was being more for lesser M values. The aerogels were characterized by bulk density, porosity, volume shrinkage, thermal conductivity, Scanning Electron Microscopy and the Fourier Transform Infrared spectroscopy.     

Characterization of the microstructures of copper-based aerogels on the sol–gel process

In this thesis, we will elaborate on the sol–gel process during the preparation of monolithic copper-based aerogel. The microstructure of the copper-based aerogel appears to be various due to the different amounts of raw materials, such as polyacrylic acid, propene oxide, deionized water (H₂O) and copper(II) chloride (CuCl₂) in the sol–gel process. The proper molar ratios between these reactants play a crucial factor in mediating the morphology of the aerogel. The aerogels are characterized by field emission scanning electron microscopy, high-resolution transmission electron microscopy and Brunauer–Emmett–Teller methods. The combined results indicate that the copper-based aerogel shows a typical three-dimensional porous structure with a large surface areas about 568 m²/g, and the skeleton structure of the aerogel is composed of a large number of primary particles with the size about a few nanometers.     

Sensing abilities of materials prepared by sol–gel technology

The advantages of the sol–gel technology are undoubtedly simplicity and versatility. It enables to obtain for example oxides in the form of layers, powders, monoliths or fibers. These materials can be successfully applied for sensing purposes due to their properties such as transparency, porosity, and high surface areas. In this article, the basis of operation of mainly optical and semiconductor sensors are presented. A brief overview of various kinds of sensors is submitted. The utility of optical fibers and planar waveguides in these systems is discussed. The paper contains also some results obtained by the authors in the field of thin film-based sensors.     

Microstructure and performance of AZO thin films prepared by sol–gel processing

Al-doped zinc oxide (AZO) films were prepared by a wet-chemical coating technique, their microstructure and crystal growth were characterized as a function of the single layer thickness. When similar final thicknesses are attained by more multiple subsequent coating-firing cycles, film porosity is reduced from over 14 to 2 %. Simultaneously the AZO crystallite size is increased from approximately 23 to 60 nm, a preferential c-axis oriented growth is observed. Different substrates (soda-lime glass, soda-lime glass with a SiO₂ barrier coating, borosilicate glass and alkali-free display glass) were used and the resulting AZO films were compared. It is found that the substrate composition primarily affects grain growth and subsequently the electrical performance of the AZO films.     

Physical and optical properties of organo-modified silica nanoparticles prepared by sol–gel

A comparative study on the physical and optical properties of silica nanoparticles prepared by sol–gel has been carried out. Post-modification of as-synthesized silica nanoparticles produced organo-functionalized silica nanoparticles slightly increased in size (~20%) and relatively high aggregation. However, in situ method produced sixfold bigger functionalized particles with good dispersion and less aggregation. Higher organic content was observed for in situ modified nanosilica, leading to a higher surface hydrophobicity that improved compatibility and dispersion in preparation of silica-polymer nanocomposite. Furthermore, in situ and post-modified nanosilica demonstrated a distinct optical activity, photoluminescence and UV compared to the unmodified nanoparticles.     

Preparation and characterization of nanocrystalline Ca-doped CeO2 by sol–gel process

The reactivity of CeO₂ is determined by grain size and oxygen vacancies, which can be achieved by doping elements with less oxidation state into CeO₂. In this study nanocrystalline Ca-doped CeO₂ sol was synthesized from the reaction of hydrate cerium (III) nitrate and calcium nitrate tetrahydrate in alcohol solution after being calcined at 600?°C. X-ray diffraction as well as selected area electron diffraction gave evidence that the synthesized Ca-doped CeO₂ samples were well crystalline and had a cubic fluorite structure. TEM observation revealed that Ca-doped CeO₂ was composed by nanoparticles with grain size around 8?nm. The Raman spectrum of pure CeO₂ consists of a single triple degenerate F_2g model characteristic of the fluorite-like structure. In the Ca-doped CeO₂ sample, two additional low-intensity Raman bands were detected, thus confirming the formation of the solid solution. The synthesized nanometric powder is expected to be used in solid oxide fuel cells as well as in the catalytic treatment of automobile exhaust fumes.     

Study of tri-layer antireflection coatings prepared by sol–gel method

Antireflective coatings (ARCs) on tri-layer thin film stacks were studied in this paper. Silica sols have been prepared by acid-catalyzed or base-catalyzed hydrolysis and condensation reactions of tetraethyl orthosilicate. Antireflective nanometric SiO₂/TiO₂ films are formed on both sides of the glass substrates by combining the sol–gel method and the dip-coating technique. Seen from the transmittance spectra of different films, a maximum light transmittance of 99.9% was obtained at the band of 300–800 nm. Scanning electron microscope (SEM) and atomic force microscopy (AFM) confirm the well-covered surface morphology. By the SEM observations we can see that the films are full of coverage on glass surface and containing no voids or cracks. The image root mean square roughness of the two types of ARCs provided by the AFM is 1.21 and 3.04 nm, respectively. Furthermore, a surface profiler was used to determine the thickness of each layer in the obtained multi-layer coating system.     

The properties of nickel aluminate nanoparticles prepared by sol–gel and impregnation methods

Nickel aluminates were prepared by sol–gel and impregnation methods and calcined at 1100 °C. The sol–gel made samples were prepared with different amounts of nickel (Ni/Al molar ratio equal to 0, 0.25, 0.5, and 0.75) and aging times (24 and 48 h). The samples were characterized by X-ray diffraction, induced couple plasma, nitrogen physisorption, transmission and scanning electron microscopy, and ammonia temperature programmed desorption (NH₃-TPD). In the sol–gel made samples, only the NiAl₂O₄ structure of nickel aluminate was defined, while for impregnation, NiAl₁₀O₁₆ was formed as well. The sol–gel made samples had low specific surface areas (7.7–12.4 m²/g), but a sample prepared by impregnation method had higher specific surface area (67.2 m²/g). The surface acidity density decreased by increasing the amount of nickel and was the lowest for impregnation method.     

Multi-parameter evaluation of fast sol–gel process by terahertz measurements

We present a feasibility study to apply terahertz (THz) spectroscopy and THz imaging as non-destructive diagnostic tools for sol–gel analysis, manufacturing and quality control. By performing THz spectroscopy on liquid and solid samples we were able to follow several key parameters during the sol–gel formation process and of the final product. Sol–gel transformations were monitored by THz absorption, whereas density changes have been observed through changes in refractive indices. Time domain spectroscopy (TDS), both in transmission and reflection geometries, was used to monitor the properties of fast sol–gel resins. THz imaging of gold coated, thin-film sol–gel enables us to determine inhomogeneities and defects in their internal structure. We demonstrated that THz spectroscopy can be implemented as an online analytical tool for multi-parameter evaluation of the sol–gel process during fabrication, and of the final product.     

LiFe5O8 prepared by sol–gel synthesis: microstructural and morphological effects by organic and inorganic templates

Lithium ferrite was prepared using a sol–gel growth process using different fuels and inorganic templates. The aim of this study is to evaluate the influence of inorganic template agent like KCl, KBr and KI as well as the effect of different fuels like urea, glycine and citric acid on the morphology change of lithium ferrite. The structure, morphology and magnetic properties of the ferrite were investigated using powder X-ray diffraction (XRD), Infrared red spectroscopy and vibrating sample magnetometer. Thermal decomposition studies reveal the formation of lithium ferrite at a low temperature ~440 °C. Powder XRD pattern has shown the formation of a single α-phase lithium ferrite except the sample with inorganic template KBr, in which the presence of hematite as a secondary phase was observed. Scanning electron microscopy studies show that the structural morphology is highly sensitive to the inorganic template as well as on the fuel. The rod shaped nanoparticles are observed with the inorganic template KCl and KBr. The decrease in grain size is observed for LiFe₅O₈/glycine as compared to LiFe₅O₈/citric acid and flake shaped dense particles are observed for LiFe₅O₈/urea. The magnetic properties of the ferrite have also been investigated.     

Synthesis and characterization of nitrogen-doped TiO2 nanoparticles prepared by sol–gel method

The N-doped TiO₂ has been synthesized by sol?Cgel method, using titanium isopropoxide, isopropanol and an aqueous solution of ammonia with ratio 2:1:10. The concentrations used for the NH₃ aqueous solution were 3, 7, 10 and 15?%. The samples have been analysed by X-ray diffraction, electron microscopy (SEM and TEM) thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), micro-Raman spectroscopy and diffuse reflectivity. TEM, SEM, DSC and TGA showed that the morphology is influenced by the presence of N^3? ions but not by the concentration of the solution. Instead reflectance gave us a relation between values of the energy gap and the concentration of N^3? ions: the gap between valence and conduction band lowers as the concentration of NH₃ in the starting solution increases. From these results we can say that the properties of the material have been tuned by doping with nitrogen ions because the particles absorb more light in the visible range, and this is important for photovoltaic and photocatalytic applications.     

Bulk production of multi-wall carbon nanotube bundles on sol–gel prepared catalyst

A method to grow multi-wall carbon nanotube bundles in a high yield (weighing over 15 times the catalyst) is developed and a plausible explanation for the formation and high yield of the bundles is suggested. The Co–Mo–Mg–O catalyst used in the experiment is prepared by a sol–gel technique, molybdenum being doped into the catalyst through oxidation and diffusion at 750 °C. Small changes to the catalyst preparation lead to the growth of single-wall carbon nanotubes (SWNTs). Our work is an exploitation of the high performance of the solid catalyst in the synthesis of novel nanomaterials.