Resolution of positional isomers by capillary electrochromatography

Electroseparations have been very successful in increasing efficiencies and reducing analysis times. The analytical technique originally applied to open tube capillaries (capillary electrophoresis) has been used as a basis to develop renewed interest in electrochromatography. This paper describes the use of capillary electrochromatography to separate two positional isomers and describes a comparison between gas chromatography (GC), capillary electrochromatography (CEC) and nano-HPLC. The resolution of these isomers is quite crucial, since one of the isomers is the impurity in a pharmaceutically active drug.     

S-citalopram imprinted monolithic columns for capillary electrochromatography enantioseparations

In this study, the molecular imprinting method was used to separate enantiomeric forms of chiral antidepressant drug, R,S-citalopram (R,S-CIT) in aqueous solution by CEC system combining the advantages of capillary electrophoresis (CE) and high-performance liquid chromatography (HPLC). For that, an amino acid-based molecularly imprinted monolithic capillary column was designed and used as a stationary phase for selective separation of S-citalopram (S-CIT) for the first time. S-CIT was selectively separated from the aqueous solution containing the other enantiomeric form of R-CIT, which is the same in size and shape as the template molecule. Morphology of the molecularly imprinted (MIP S-CIT) and non-imprinted (NIP S-CIT) monolithic capillary columns was observed by scanning electron microscopy. Imprinting efficiency of MIP S-CIT monolithic capillary column used for selective S-CIT separation was verified by comparing with NIP S-CIT and calculated imprinting factor (I.F:1.81) proved the high selectivity of the MIP S-CIT for S-CIT. Cavities formed for S-CIT form enabled selective (α = 2.08) separation of the target molecule from the other enantiomeric R-CIT form. Separation was achieved in a short period of 10 min, with the electrophoretic mobility of 7.68 × 10⁻⁶ m²/Vs for R,S-CIT at pH 7.0 10 mM PB and 50% ACN ratio. The performance of both MIP S-CIT and NIP S-CIT columns was estimated by repeating the R,S-CIT separations with intra-batch and inter-batch studies for reproducibility of retention times of R,S-CITs. Estimated RSD values that are lower than 2% suggest that the monolithic columns separate R,S-CIT enantiomers without losing separation efficiency.     

Preparation of monolithic capillary columns for capillary electrochromatography by γ-ray irradiation

A novel approach is introduced and evaluated for the preparation of silica-based monoliths by a sol–gel technique where in situ polymerization was carried out by γ-ray irradiation within the capillary. The γ-radiation-initiated synthesis generated radicals directly on the monomer, thereby avoiding use of any initiator. The chromatographic behavior of the capillary monolithic columns was studied in the modes of CEC, p-CEC and low pressure-driven separation, all of which exhibited reversed-phase character. Various operational parameters, such as column temperature, separation voltage, acetonitrile content and buffer pH, were varied to assess their influence on column performance in the separation of a series of neutral compounds including thiourea, benzene, toluene, ethyl benzene, biphenyl and naphthalene. A scanning electron micrograph of a cross-section of the capillary column showed that the gel took the form of a spherical particle aggregate and adhered to the column inner wall. It provided a viable alternative to either thermally initiated or photo polymerization for the preparation of monolithic columns.     

Preparation and characterization of monolithic polymer columns for capillary electrochromatography

A series of micro-monolithic columns with different porosities were prepared for capillary electrochromatography (CEC) by in-situ copolymerization of butyl methacrylate, ethylene glycol dimethacrylate, and 2-acrylamido-2-methyl-1-propane-sulfonic acid in the presence of a porogen in fused-silica capillaries of 100 microm I.D. Different column porosities were obtained by changing the ratios of monomers to porogenic solvents. Columns were investigated and evaluated under both pressure-driven (high-performance liquid chromatography, HPLC) and electro-driven (capillary electrochromatography, CEC) conditions. Each column exhibited different efficiency and dependency on flow velocity under electro-driven conditions. Abnormally broad peaks for some relatively bulky molecules were observed. Possible explanations are discussed. The differences in column efficiency and retention behavior between the two eluent-driven modes were studied in detail. In addition, other column properties, such as morphology, porosity, stability and reproducibility, were extensively tested.     

Ionic liquids monolithic columns for protein separation in capillary electrochromatography

A series of ionic liquids (ILs) monolithic capillary columns based on 1-vinyl-3-octylimidazolium (ViOcIm⁺) were prepared by two approaches (“one-pot” approach and “anion-exchange” approach). The effects of different anions (bromide, Br⁻; tetrafluoroborate, BF₄⁻; hexafluorophosphate, PF₆⁻; and bis-trifluoromethanesulfonylimide, NTf₂⁻) on chromatography performance of all the resulting columns were investigated systematically under capillary electrochromatography (CEC) mode. The results indicated that all these columns could generate a stable reversed electroosmotic flow (EOF) over a wide pH range from 2.0 to 12.0. For the columns prepared by “one-pot” approach, the EOF decreased in the order of ViOcIm⁺Br⁻ > ViOcIm⁺BF₄⁻ > ViOcIm⁺PF₆⁻ > ViOcIm⁺NTf₂⁻ under the same CEC conditions; the ViOcIm⁺Br⁻ based column exhibited highest column efficiencies for the test small molecules; the ViOcIm⁺NTf₂⁻ based column possessed the strongest retention for aromatic hydrocarbons; and baseline separation of four standard proteins was achieved on ViOcIm⁺NTf₂⁻ based column corresponding to the highest column efficiency of 479 000 N m⁻¹ for cytochrome c (Cyt c). These results indicated that the property of ILs based columns could be tuned successfully by changing anions, which gave these columns potential to separate both small molecules and macro biomolecules.     

Preparation and characterization of C16 monolithic columns for capillary electrochromatography

A series of methacrylamide-based C16 monolithic columns were prepared and characterized to determine how their porous structural properties and chromatographic behavior are affected by the percentages of functional monomer, base monomer, and cross-linker in the polymerization solution. Baseline separation of 6 neutral compounds can be readily obtained in an optimized column. Furthermore, the effects of organic additive in the mobile phase, operating voltages, and temperature on retention behaviors and separation efficiencies were also studied. The separation mechanism is also discussed. High column efficiency and good reproducibility indicate that the monolithic columns hold considerable promise.     

Analyses of benzophenones by capillary electrochromatography using methacrylate ester-based monolithic columns

In this study, eight benzophenones, which are commonly used as UV filters in various cosmetics and plastics, were analyzed by capillary electrochromatography with a methacrylate ester-based monolithic column. The effects of the composition and pH of mobile phase, porogenic solvent ratio, and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) content on benzophenone separations were examined. For all benzophenones, separation performances were markedly improved in monolithic columns with larger 1-propanol ratio and higher AMPS content. Furthermore, a twofold increase in AMPS content almost reduced the separation time in half when a monolithic column had an adequately high surface area, i.e. monolithic column was produced in a higher ratio of 1-propanol. As well, the retention behaviors of these analytes in the monolithic column were strongly influenced by the level of acetonitrile in the mobile phase, and the pH of the mobile phase also had an apparent influence on separation resolution.     

Enantioseparation on cellulose dimethylphenylcarbamate-modified zirconia monolithic columns by reversed-phase capillary electrochromatography

This work reports the preparation of monolithic zirconia chiral columns for separation of enantiomeric compounds by capillary electrochromatography (CEC). Using sol–gel technology, a porous monolith having interconnected globular-like structure with through-pores is synthesized in the capillary column as a first step in the synthesis of monolithic zirconia chiral capillary columns. In the second step, the surface of the monolith is modified by coating with cellulose tris(3,5-dimethylphenylcarbamate) (CDMPC) as the chiral stationary phase to obtain a chiral column (CDMPCZM). The process of the preparation of the zirconia monolithic capillary column was investigated by varying the concentrations of the components of the sol solution including polyethylene glycol, water and acetic acid. CDMPCZM is mechanically stable and no bubble formation was detected with the applied current of up to 30 μA. The enantioseparation behavior of the CDMPCZM columns was investigated by separating a set of 10 representative chiral compounds by varying the applied voltage and pH and organic composition of the aqueous organic mobile phases.     

Analyses of preservatives by capillary electrochromatography using methacrylate ester-based monolithic columns

Five common food preservatives were analyzed by capillary electrochromatography, utilizing a methacrylate ester-based monolithic capillary as separation column. In order to optimize the separation of these preservatives, the effects of the pore size of the polymeric stationary phase, the pH and composition of the mobile phase on separation were examined. For all analytes, it was found that an increase in pore size caused a reduction in retention time. However, separation performances were greatly improved in monolithic columns with smaller pore sizes. The pH of the mobile phase had little influence on separation resolution, but a dramatic effect on the amount of sample that was needed to be electrokinetically injected into the monolithic column. In addition, the retention behaviors of these analytes were strongly influenced by the level of acetonitrile in the mobile phase. An optimal separation of the five preservatives was obtained within 7.0 min with a pH 3.0 mobile phase composed of phosphate buffer and acetonitrile 35:65 v/v. Finally, preservatives in real commercial products, including cold syrup, lotion, wine, and soy sauces, were successfully determined by the methacrylate ester-based polymeric monolithic column under this optimized condition.     

Peroxodisulfate as a chemical initiator for methacrylate-ester monolithic columns for capillary electrochromatography

Organic monolithic stationary phases for CEC were synthesized in situ in fused-silica capillaries. Polymerization mixtures were composed of butyl methacrylate, ethylene dimethacrylate, and [2-(methacryloyloxy)ethyl]trimethyl ammonium chloride in the presence of a porogenic solvent, using ammonium peroxodisulfate as chemical initiator, and N,N,N',N'-tetramethylethylenediamine to activate the reaction. The influence of the amount of initiator, temperature, and composition of porogenic solvent on the physical and chromatographic properties of monolithic stationary phases has been investigated. A minimum plate height of 14.5 microm was obtained at 18 wt% of 1,4-butanediol in the polymerization mixture. The produced monolithic stationary phases exhibited a good repeatability and batch-to-batch and mixture-to-mixture reproducibility, with RSD values below 5.6% in the electrochromatographic parameters studied. A comparison with columns prepared by thermal initiation with alpha,alpha'-azobisisobutyronitrile (AIBN) was also performed. The most efficient column initiated with peroxodisulfate showed better efficiencies and selectivities than that prepared with AIBN at the same composition mixture.     

Practical aspects of using methacrylate-ester-based monolithic columns in capillary electrochromatography

Methacrylate-ester-based monoliths containing quaternary ammonium groups were prepared in situ in capillary columns and in simultaneous experiments in vials, employing thermal initiation. The chromatographic properties of the monoliths were determined with capillary electrochromatography (CEC), and their morphology was studied with mercury-intrusion porosimetry on the bulk materials. Materials with different, well repeatable pore-size distributions could be prepared. A satisfactory column-to-column and run-to-run repeatability was obtained for the electro-osmotic mobility, the retention characteristics (k-values) and the efficiency on the columns prepared and tested in the CEC mode. A relatively high electro-osmotic flow was observed in the direction of the positive electrode. The electro-osmotic mobility was found to be influenced only marginally by mobile-phase parameters such as the pH, ionic strength, and acetonitrile content. The retention behavior of the monolithic columns was similar to that of columns packed with C18-modified silica particles. Columns could be prepared with optimum plate heights ranging from 6 microm for unretained compounds to 20 microm for well retained (k=2.5) polyaromatic hydrocarbons. However, for specific analytes a - still unexplained - lower chromatographic column efficiency was observed.     

Design of the monolithic polymers used in capillary electrochromatography columns

Monolithic columns for capillary electrochromatography (CEC) are receiving quite remarkable attention. Both the simplicity of the in situ preparation and the large number of readily available chemistries make the monolithic separation media a vital alternative to capillary columns packed with particulate materials. This review summarizes the current state-of-the-art in this rapidly growing area of CEC with a focus on monolithic capillary columns prepared from synthetic polymers. Recent achievements in column technologies for both high-performance liquid chromatography and capillary electrophoresis are used as the starting point to highlight the influence of these well established analytical methods on the development of monolithic capillary columns for CEC. The effects of individual variables on the separation properties of monolithic capillaries are discussed in detail. The analytical potential of these columns is demonstrated with separations involving various families of compounds in different chromatographic modes.     

Chemically L-prolinamide-modified monolithic silica column for enantiomeric separation of dansyl amino acids and hydroxy acids by capillary electrochromatography and mu-high performance liquid chromatography

A silica-based chiral monolithic column prepared by sol-gel process and chemical modification of chiral selector was used for enantioseparation of dansyl amino acids and hydroxy acids by capillary electrochromatography (CEC) and mu-high-performance liquid chromatography (mu-HPLC). L-Prolinamide was modified as a chiral selector. The chiral stationary phase (CSP), the chiral complex of Cu(II) with L-prolinamide, provides an anodic electroosmotic flow (EOF) in CEC. The EOF was found to be dependent on applied electric field strength, the pH, and the composition of mobile phases. Scanning electron micrograph showed that monolithic columns have the morphology of continuous skeleton and large through-pore. D-Enantiomers migrated before L-enantiomers except for dansyl-(Dns)-DL-Ser. The separation efficiencies of up to 17600 (D) and 13,200 plates m(-1) (L) were achieved for the separation of DL-indole-3-lactic acid.     

Protein separation by monolithic capillary electrochromatography

This work presents the separation of model proteins by capillary electrochromatography involving a monolithic stationary phase with C4 functionality. The monolith was fabricated in UV-transparent capillaries by employing a slight modification of a recently published photopolymerization procedure. With the number of theoretical plates per column ranging between 11000 and 33000, the separation efficiency proved to be lower than capillary zone electrophoresis where plate numbers ranged between 18000 and 66000. However, higher resolution was obtained due to the additional chromatographic separation mechanism. Inter- and intra-column reproducibility were evaluated, the latter could be significantly improved when using a rinsing procedure that contained 0.05% sodium dodecylsulfate in the mobile phase. Plate heights became nearly independent of mobile phase velocities higher than 0.5 mm/s indicating that high velocities can be applied without sacrificing efficiency. Furthermore, peak heights showed a dependence on injection times. For proteins, an increase in capacity factors was found when increasing the percentage of organic solvent in the mobile phase.     

Separation of enantiomers by capillary electrochromatography

The current popularity of capillary electrochromatography (CEC) has led to an increasing number of studies on the development and evaluation of enantioselective CEC systems. These studies clearly demonstrate that the most prominent advantage of electrically driven separation methods, the vastly increased column efficiency as compared to pressure-driven chromatography, can also be experimentally achieved for the separations of enantiomers. In analogy to high-performance liquid chromatography (HPLC) and capillary electrophoresis (CE), several approaches have been used. The addition of a chiral selector to the mobile phase is the simplest method. Less erroneous and more elegant approaches are those that use open-tubular, conventional packed, and monolithic columns containing chiral stationary phases that stereoselectively interact with enantiomers. This review evaluates the new techniques and compares them to enantioselective HPLC and CE. Further, it describes the various concepts of enantioselective CEC and focuses on the current ‘state-of-the-art' column technology.     

Comparison on photo-initiators for the preparation of methacrylate monolithic columns for capillary electrochromatography

The synthesis of lauryl methacrylate monoliths for capillary electrochromatography by UV polymerization using several free-radical initiators (α,α′-azobisisobutyronitrile, 2,2-dimethoxy-2-phenylacetophenone, dibenzoyl peroxide (BPO) and lauroyl peroxide (LPO)) has been investigated. Using a 1,4-butanediol/1-propanol mixture as porogenic solvent, the influence of each initiator and its content on the morphological and electrochromatographical properties of beds was evaluated. Under their respective optimum content, satisfactory separations of a test mixture of PAHs with similar efficiencies (minimum plate heights of 8.0–12.7 μm obtained from Van Deemter plots) were achieved for the four investigated photo-initiators. The columns photo-polymerized with LPO provided the best compromise between chromatographic performance and analysis time. Moreover, this initiator showed a fine control in the column retention properties. The resulting monolithic columns exhibited a good run-to-run repeatability in the tested chromatographic parameters (RSD < 2.4%) for all initiators investigated; and satisfactory column-to-column repeatability (RSD < 6.0%), except for beds photo-polymerized with BPO (RSD < 10.8%).     

Separation of selected humic degradation compounds by capillary electrochromatography with monolithic and packed columns

The separation of selected lignin/humic substance (HS) degradation compounds by capillary electrochromatography (CEC) with a methacrylate-based monolithic column and a conventional column packed with 5 microm octadecyl silica (ODS) particles is presented. The effects of organic modifier concentration, pH of the mobile phase, ionic strength, applied voltage, and temperature on the separation were investigated to determine the optimal separation conditions. With the increase of pH in the mobile phase, some of analytes start to ionize and both chromatographic partition and electrophoresis can play roles in separation simultaneously. Accordingly, different selectivity from high-performance liquid chromatography (HPLC) and capillary electrophoresis (CE) could be achieved. The performances of both kinds of columns were compared. The results showed that the peaks of compounds obtained on the former column were much wider than those on the latter one, although good separation efficiency of alkylbenzenes could be readily achieved; the most probable reasons for this behavior and method to solve this problem were briefly discussed. The CEC of a soil fulvic acid with a monolithic column produced partly resolved broad bands; by means of nuclear magnetic resonance (NMR) analysis a wide range of oxygen derived aromatic substitution patterns was found with prominent contributions from phenolic and carboxylic groups.     

Packing columns for capillary electrochromatography

Considering the current interest in capillary electrochromatography (CEC), performed in packed columns, we present the different methods used to pack capillary columns for use in CEC. General considerations on column packing are given and the column fabrication process is discussed in sufficient detail to allow instruction to those who are not experienced in the field. Five different packing methods are discussed to deliver packing material into the capillary column from a practical view point: slurry pressure packing, packing with supercritical CO2, electrokinetic packing, using centripetal forces, and packing by gravity. Entrapment of particulate material by sintering and sol-gel technology is also mentioned. Although slurry pressure packing procedures are most common, higher separation efficiencies are obtained using other packing approaches. Electrokinetic packing seems to be the simplest technique to deliver the packing material into the capillary columns. Nevertheless, as with the other packing techniques, skill and experience are required to complete all the steps involved in the fabrication of packed columns for CEC.