Analysis of nitrated polycyclic aromatic hydrocarbons

Many nitrated polycyclic aromatic hydrocarbons (NPAH) that are present in low concentrations in the environment and in emission sources have been shown to be mutagenic and/or carcinogenic. This paper reviews the current methods of analysis of these compounds with the emphasis on NPAH measurements in ambient particulate matter samples.     

High-performance liquid chromatography determination of nitrated polycyclic aromatic hydrocarbons by indirect fluorescence detection

A high-performance liquid chromatography (HPLC) method for the analysis of nitrated polcyclic aromatic hydrocarbons (NPAHs) is reported. NPAH mixtures were pre-concentrated using solid-phase extraction and well resolved on a C(18) column. They were detected using an indirect method involving the quenching of the emission from the fluorophores 5,6,7,8-tetrahydronaphthol (5,6,7,8-THN-1-OH), 7-amino-4-methyl coumarin (Coumarin 120, COU-120) and 3-hydroxy-4-(2-hydroxy-4-sulfo-1-naphthylazo)2-naphthalene carboxylic acid (Calcon carboxylic acid, CCA). Linear calibration curves were obtained in the range 1.1 x 10(-9) to 1.1 x 10(-8) mol/L. Using COU 120 as the fluorophore, the detection limit was 2.9 x 10(-10) mol/L for 1-nitronaphthalene and 2.1 x 10(-11) mol/L for 2-nitrofluorene. Recoveries of NPAHs from spiked tap water samples were between 88 and 100%.     

Simplified determination of polycyclic aromatic hydrocarbons

Accurate quantitative analysis for selected polycyclic aromatic hydrocarbons present on urban dust can be obtained by using a simple procedure consisting of sonic-probe extraction with cyclohexane; clean-up with Florisil((R))-XAD-4((R)), and measurement by high-resolution gas chromatography with flame-ionization detection (HRGC/FID). The analysis can be further simplified by eliminating the clean-up step if HRGC/electron-impact mass-spectrometry (MS) is available. Both the FID and MS methods give results consistent with those obtained by standard procedures. The direct HRGC/MS procedure, combined with chemical ionization, can also be applied to the determination of polycyclic organic materials present in solvent-refined coal, shale oil and crude oil.     

Determination of nitrated polycyclic aromatic hydrocarbons and their precursors in biotic matrices

Analytical method for the determination of ultra-trace levels of nitro-PAHs in various biotic matrices has been developed. Soxhlet extraction and/or solvent extraction enhanced by sonication were used for isolation of target analytes; GPC followed by SPE were employed for purification of crude extracts. GC-MS/NCI technique was utilised for identification/quantitation of target analytes. Performance characteristics of implemented method were obtained through thorough in-house validation procedure. The main sources of uncertainties were critically evaluated, possible strategies of their elimination/minimisation were considered and consequently employed. Examination of real-life samples of various foodstuffs (complete human diet, mate tea, pumpkin seed oil, parsley, sausages) was performed in this study.     

The spectrophotometric determination of polycyclic aromatic hydrocarbons

The determination of polycyclic aromatic hydrocarbons by elution chromatography from alumina columns followed by ultra-violet spectrophotometry has been elaborated for a more extended range of substances than has been published previously. The methods have been standardised and tables of absorption peaks are provided for easy identification of a number of compounds commonly found as traces in combustion products. Recommendations are given for the preparation of samples for determinations by this method, which has been successfully employed for the analysis of carbon blacks, soots, urban air solids, condensible smokes such as tobacco smoke, wood smoke and coal tar. thermal decomposition or pyrolysis products and other substances, such as urban vegetation, soil, tobacco, snuff, smoked food, and surface drainage water, which have been subjected to the action of smokes or other combustion products.     

Trace determination of nitrated polycyclic aromatic hydrocarbons using liquid chromatography with on-line electrochemical reduction and fluorescence detection

An efficient clean-up procedure coupled with a high performance liquid chromatography (HPLC) with on-line electrochemical (EC) reduction and fluorescence detection (FLD) was developed to quantify nitrated polycyclic aromatic hydrocarbons (NPAHs) in the airborne particulate. In this process, NPAHs were extracted ultrasonically followed by analysis by using a reversed phase column with an aqueous eluent containing 70% aqueous acetonitrile and sodium monocholoroacetate as a buffer solution. The extraction efficiencies were above 83% for 1-nitropyrene and 1,3-dinitropyrene (1,3-DNP) 1,6-DNP, and 1,8-DNP, and calibration graphs were linear with very good correlation coefficients (r>0.999) and the detection limits were in the range of 1.0-2.2 pg for dinitropyrenes and nitropyrene. The proposed method provides a relatively simple and convenient procedure for determining the NPAHs samples in airborne particulate.     

Standard reference materials for the determination of polycyclic aromatic hydrocarbons

Summary Since 1980 a number of Standard Reference Materials (SRM's) have been issued by the National Bureau of Standards (NBS) to assist in validating measurements for the determination of polycyclic aromatic hydrocarbons (PAH) and other polycyclic aromatic compounds (PAC). These SRM's are certified for selected PAC and range in analytical difficulty from calibration solutions to complex natural matrix materials, such as air and diesel particulate matter, shale oil, and crude oil. In the past year three new SRM's have been introduced: (1) SRM 1647a Priority Pollutant PAH in Acetonitrile, (2) SRM 1491 Aromatic Hydrocarbons in Hexane/Toluene, and SRM 1597 Complex Mixture of PAH from Coal Tar. The SRM's available from NBS for use in the determination of PAC are described and the concentrations of PAC determined in the natural matrix SRM's are summarized and compared. The primary analytical techniques used for the measurement of PAC in these SRM's were gas chromatography, liquid chromatography, and gas chromatography/mass spectrometry.

---

Standardreferenzmaterialien für die Bestimmung von polycyclischen aromatischen Kohlenwasserstoffen

     

Method for determination of polycyclic aromatic hydrocarbons by fluorodensitometry

A TLC fluorodensitometric method for the determination of total PAHs in aqueous and hydroalcoholic solutions at the parts per billion level has been developed. The PAHs are extracted into cyclohexane and separated as a class on a chemically bonded reversed-phase TLC plate using stepwise development. In the fluorescence scanning of the plate the PAHs are located by reference to a mixture of 16 PAHs designated by EPA as primary pollutants and measured as benzo(a)pyrene.     

Simple and sensitive method for determination of nitrated polycyclic aromatic hydrocarbons in diesel exhaust particles by gas chromatography-negative ion chemical ionisation tandem mass spectrometry

An extremely simple and sensitive method was developed for determination of nitrated polycyclic aromatic hydrocarbons (nitro-PAHs; mono-nitro-PAHs and dinitropyrenes) in diesel exhaust particles (DEPs) by gas chromatography-negative ion chemical ionisation tandem mass spectrometry (GC/NCI/MS/MS). We used two types of column in GC/NCI/MS/MS analysis. A polar column was used for determination of mono-nitro-PAHs, and a non-polar column was used for determination of dinitropyrenes and mono-nitro-PAHs except nitrofluoranthenes. The proposed method requires no clean-up procedure. The limits of detection ranged from 0.01 to 0.09 pg for all compounds tested. The applicability of the method to DEP samples was validated using diesel particulate standard reference materials (SRMs). Although DEPs contain complex matrices, all compounds could be detected easily in SRM2975 (diesel particulate matter) and SRM1975 (diesel particulate extract) without a clean-up procedure. The RSDs were less than 5% for all compounds examined. The quantitative results for SRMs exhibited good agreement with the available data in the literature. These results indicate that the proposed GC/NCI/MS/MS method is useful for determination of nitro-PAHs in DEP samples.     

Negative ion laser desorption ionization time-of-flight mass spectrometry of nitrated polycyclic aromatic hydrocarbons

Nitrated polycyclic aromatic hydrocarbons (nitro-PAHs) are widespread environmental pollutants that are generated by incomplete combustion and by atmospheric transformation of polycyclic aromatic hydrocarbons (PAHs). Many nitro-PAH compounds are potent genotoxins and some are direct acting mutagens. Detection of nitro-PAHs in aerosols is complicated by small sample sizes and nitro-PAH abundances that are 1–2 orders of magnitude less than analogous unsubstituted PAHs. Selective detection of several nitro-PAHs by using laser desorption ionization time-of-flight mass spectrometry in negative ion mode has been achieved. Desorption and ionization of nitro-PAHs were effected by using pulsed UV radiation at 266 and 213 ran. Intense molecular anions were observed in addition to fragments identified as CN^? and NO ₂ ^? , which were characteristic indicators of the presence of nitro-PAHs. Selective detection of nitro-PAHs in negative ion mode was demonstrated in the analysis of a diesel particulate sample.     

Pressurised solvent extraction of nitrated derivatives of polycyclic aromatic hydrocarbons from roadside dust

An analytical method based upon the pressurised solvent extraction and gas chromatography and mass spectrometry (GC-MS) for analysis of nitrated derivatives of polycyclic aromatic hydrocarbons (nitro-PAHs) in roadside dust has been developed. Five nitro-PAHs (1-nitronaphthalene, 1-nitropyrene, 9-nitroanthracene, 2-nitrofluorene, 6-nitrochrysene) were chosen for this study because of their variable physical properties and effect on human health. Experiments with spiked inert matrix were used for the best extraction conditions finding. Different extraction conditions (temperature, pressure, solvents and duration of extraction cycle) were examined. The highest recoveries were observed at the extraction pressure of 14?MPa, temperature of 100°C and two cycles of 5?min extraction time, when dichloromethane was used as an extraction solvent. These conditions were applied to the extraction of nitro-PAHs from roadside dust. After extraction the nitro-PAHs fraction was isolated by the silica gel column chromatography. The GC-MS detector was used for analyses of the extracts. Recoveries of nitro-PAHs after extraction from roadside dust ranged from 60% for 9-nitroanthracene to 108% for 6-nitrochrysene.     

Solid-phase microextraction combined with gas chromatography/triple quadrupole tandem mass spectrometry for determination of nitrated polycyclic aromatic hydrocarbons in sediments

Nitro-polycyclic aromatic hydrocarbons have been detected in various environmental media. However, determination in sediment matrix is challenging due to the lack of a suitable method. In this study, a reliable method for determining 15 nitro-polycyclic aromatic hydrocarbons in sediments was developed based on accelerated solvent extraction and solid-phase microextraction coupled with gas chromatography–tandem mass spectrometry. The accelerated solvent extraction and solid-phase microextraction are sample pre-treatment techniques that have advantages, such as rapid operation and minimal sample volume. Initially, the solid-phase microextraction was optimized using five commercial fibers and from that 65 μm polydimethylsiloxane/divinylbenzene fiber was selected as the best fiber. Further, the accelerated solvent extraction conditions were optimized by Taguchi experimental design, such as extraction temperature (120℃), extraction solvent (dichloromethane), number of cycles (two), static extraction period (4 min), and rinse volume (90%). The method parameters, such as limits of quantitation, and intraday and interday accuracy and precision, were in the range of 0.067–1.57 ng/g, 75.2–115.2%, 69.9–115.4%, and 1.0–16.5%, respectively. Upon meeting all the quality criteria, the method was applied successfully to analyze real sediment samples. Therefore, our study creates a new prospect for the future application of direct immersion solid-phase microextraction in sediment analysis.     

Adsorption preconcentration in the luminescence determination of polycyclic aromatic hydrocarbons

The adsorption of polycyclic aromatic hydrocarbons (PAHs)—pyrene, anthracene, phenanthrene, and fluorene—by a cellulose matrix of micellar media containing sodium dodecyl sulfate and a nonionogenic polymer, namely, polyethylene glycol is studied. Procedures are proposed for the luminescence determination of PAHs in the adsorbent phase.     

Development of an improved method for the determination of polycyclic aromatic hydrocarbons in mainstream tobacco smoke

A gas chromatograph/mass-selective detection (GC/MS) method has been developed and validated for the quantitation of 16 polycyclic aromatic hydrocarbons found in mainstream tobacco smoke condensate. The utilization of two types of solid-phase extraction media combined with capillary column technology removed matrix interferences, afforded a significant reduction in analysis run time, and increased accuracy. Also, the addition of a chilled impinger was used to trap semi-volatile polycyclic aromatic hydrocarbons and to provide more accurate data. This was done without sacrificing the repeatability, reproducibility, and precision obtained in previously published methods. The development and validation studies discussed in this paper resulted in an improved, robust analytical method capable of increasing laboratory capacity and reducing sample reporting time.     

Chromatographic determination of polycyclic aromatic hydrocarbons in oil sludge

It has been demonstrated that the Oasis HLB polymer adsorbent can be used for the purification of hexane extracts of oil sludge for the determination of polycyclic aromatic hydrocarbons by high-performance liquid chromatography with a fluorometric detector in these samples. The determination of polycyclic aromatic hydrocarbons has been carried out in samples of different wastes.     

Liquid chromatographic method with fluorescence detection for the determination of polycyclic aromatic hydrocarbons in environmental samples

A method for the determination of some polynuclear aromatic hydrocarbons (PAHs) in water samples and air filters is presented. Samples were extracted with light petroleum-diethyl ether (85 + 15) and the extracts were concentrated before analysis. Reversed-phase liquid chromatography with fluorescence detection was applied to separate and determine the PAHs. Recoveries of individual PAHs from spiked water samples were 0.16–0.27 ng ml^?1. Detection limits in the picogram range were obtained for each compound.     

Accelerated extraction for determination of polycyclic aromatic hydrocarbons in marine biota

A rapid and simple method is proposed for determination of polycyclic aromatic hydrocarbons (PAH) in complex matrices such as marine biota. The method uses sonication, by means of an ultrasonic probe, as a new tool for assisted extraction, coupled with reversed-phase liquid chromatography (RP-LC) with fluorescence detection (FL) for determination of 16 US EPA priority PAH. Separation and detection of the 16 PAH were complete in 45 min by RP-LC with a C₁₈ column and acetonitrile–water gradient elution. Multivariate optimisation of the variables affecting extraction (ultrasound radiation amplitude, sonication time, and temperature of the water-bath in which the extraction cell was placed) was conducted. The accuracy of the method was determined by analysis of a certified reference material and comparison of the results obtained with those from another method (microwave-assisted extraction and GC–MS). The new technique avoids the main problems encountered in the determination of PAH in complex matrices such as marine biota, and no clean-up step is necessary. The method was applied to determination of PAH in estuarine biota samples from the Urdaibai estuary (Biscay, Spain).