聚苯乙烯-嵌段-聚丁二烯有序多孔膜在可收缩膜上的形变研究和光学性质

利用溶剂散逸自组装法在潮湿的条件下,制备了聚苯乙烯-聚丁二烯嵌段聚合物（PS-b-PB）有序多孔膜。 利用聚乙烯可收缩膜将PS-b-PB多孔膜进行两次收缩,形成小孔径的有序多孔膜。 通过收缩,膜上的孔由圆形变为长方形或者梭形,孔的尺寸从微米级收缩至亚微米级。 利用扫描电子显微镜对膜收缩过程中2种形状产生的机理进行了研究。 结果表明,PS-b-PB结合了聚苯乙烯（PS）和聚丁二烯（PB）两个均聚物的优点,收缩后仍然保持膜结构的平整性,从而将不可见的热场变化转变为可见的光学变化。     

溶剂散逸自组装制备超疏水针垫阵列膜

利用溶剂散逸自组装方法,以聚苯乙烯、聚十二烷基丙烯酰胺-6-丙烯酰胺基己酸（CAP）和三氯甲烷为原料,在平滑的固体基质上制备了有序多孔膜,该膜上下表面可在外力作用下发生分离,得到具有微米级超疏水针垫阵列膜。 结果表明,制得的聚苯乙烯膜具备超疏水性质,与水接触角达158°。     

溶剂散逸自组装制备导电各向异性的金属有序阵列

通过溶剂散逸自组装法制备了聚苯乙烯(PS)有序多孔膜. 利用水珠在冷的PS溶液表面凝结形成有序阵列, 使PS以水珠阵列为模板形成有序多孔膜. 将有序多孔膜的上层剥离并附着在可收缩性高分子表面, 并进行离子溅射, 除掉有序多孔膜后在可收缩膜上留下了有序的金属圆盘阵列. 经过收缩, 有序阵列不仅光学性质发生了改变, 而且实现了导电的各向异性.     

水滴模板法构筑蜂窝状有序多孔膜*

水滴模板法是利用凝结并自组织有序排列的水滴为模板构筑有序蜂窝状多孔薄膜的方法。这种方法具有方便、快速、廉价、作为模板的水滴可以自然蒸发而除去,且孔洞的尺寸可以通过改变相关的实验参数方便的进行调控的优点,因而近年来受到了人们的广泛关注。本文介绍了利用水滴模板法构筑有序多孔薄膜的实验方法,探讨了形成机理和相关实验条件对多孔薄膜结构的影响,并结合当前的研究热点针对多孔薄膜的进一步应用,着重综述了水滴模板法在不同性质的成膜材料体系的应用、多孔薄膜中亚有序结构的引入以及提高多孔薄膜稳定性的方法。最后,本文展望了利用水滴模板法构筑有序多孔薄膜这一研究领域的发展前景。     

聚电解质多层有序膜电极的生成及其电化学特性

研究了在金电极表面硫醇自组装膜上聚电解质多层有序膜的形成过程及其电化学特性。用紫外光谱和电化学方法对多层有序膜进行了表征。结果表明，有序膜影响着离子在膜中的穿透性，离子型电活性物质如铁氰根离子和亚甲蓝等可嵌入有序膜中，研究了多层有序膜电极的电化学特性及膜中铁氰根离子的电化学行为。     

溶剂散逸自组装制备高分子有序微透镜阵列

利用水珠为模板制备了聚苯乙烯有序多孔膜.在溶剂挥发的制冷作用下,水珠能够在冷的高分子溶液表面凝结形成有序的阵列,溶剂蒸发完毕后,高分子材料按照水珠排列形貌空隙形成有序多孔膜,一种两性共聚物被加入到溶液中稳定水珠而获得有序的多孔结构. 将聚乙烯醇水溶液填充入多孔膜中,蒸干后用氯仿洗去聚苯乙烯,得到聚乙烯醇的整球微透镜阵列. 聚苯乙烯有序针垫阵列是由有序多孔膜撕掉上层制备的,这种针垫结构内部具有半球结构的空间,并以此为模板制备了聚乙烯醇半球微透镜阵列. 2种微透镜阵列均具有微观显影功能. 通过2种微透镜的显像对比证实,半球微透镜阵列比整球微透镜阵列具有更为清晰的多重显像效果.     

多孔氧化铝有序膜的制备研究

本文用阳极氧化法分别在硫酸和草酸电解液中成功制备出高度有序、具有纳米级孔洞的氧化铝有序阵列模板。采用饱和HgCl₂去除Al基体后,得到典型六方形结构的多孔Al₂O₃有序膜。通过改变氧化电压、氧化时间等条件使模板的孔径、孔深可调、膜厚度可控,并系统研究了对模板有序性、孔径、膜厚度等的影响因素,总结出制备Al₂O₃有序膜的最佳工艺。     

两亲性Janus粒子在蜂窝状多孔聚合物膜上的自组装性能

采用具有两亲性的两面体(Janus)粒子实现稳定的粒子界面组装与水滴模板法自组装过程相结合的方法获得了粒子在蜂窝状多孔聚合物薄膜内壁的高效定向修饰.通过与均质粒子组装形貌的对比,证明了Janus粒子因其特殊的界面自组装活性,可以获得高粒子加量条件下的规则多孔结构,解决了使用均质粒子时存在的结构有序性和粒子修饰密度之间的矛盾.而在较低粒子加量的条件下,Janus粒子也展示出与均质粒子极为不同的组装形貌.这一方法的建立,为新型表面功能化材料的制备提供了一个新的思路.     

蜂窝状有序膜功能化研究进展*

水滴模板法是近年来引人瞩目的一种制备有序微结构材料的方法,所制备的蜂窝状有序膜在微容器和微反应器、图案化模板、细胞培养支架、光学材料、超疏水表面、分离膜等领域具有十分重要的应用前景。本文对蜂窝状有序膜功能化研究的最新进展进行了系统总结,详细介绍和分析了原位多层次自组装、表面接枝、生物活性分子固定、交联、模板法成膜以及表面填充等蜂窝状有序膜的功能化方法。     

漆酚醛胺聚合物多孔膜的制备

以漆酚醛胺聚合物(UFDP)为成膜材料,利用水辅助自组装的固体基板展开法和水面展开法制备了漆酚醛胺聚合物多孔膜.研究了在静态(即不在聚合物表面吹扫氮气)高湿度环境下聚合物溶液浓度、环境湿度和固体基板等因素对多孔膜形貌的影响.结果表明,水面展开法更有利于形成单层的多孔膜而固体基板展开法得到的是多层的多孔膜.当UFDP聚合物浓度为6.0 mg/mL,环境相对湿度为90%时,用水面展开法制得的单层多孔膜的孔径分布较均匀.     

Preparation of Microporous ORMOSILs by Thermal Degradation of Organically Modified Siloxane Resin

Silicon containing materials have traditionally been used in microelectronic fabrication. Semi-conductor devices often have one or more arrays of patterned interconnect levels that serve to electrically couple the individual circuit elements forming an integrated circuit. These interconnect levels are typically separated by an insulating or dielectric film. Previously, a silicon oxide film was the most commonly used material for such dielectric films having dielectric constants (k) near 4.0. However, as the feature size is continuously scaling down, the relatively high k of such silicon oxide films became inadequate to provide efficient electrical insulation. As such, there has been an increasing market demand for materials with even lower dielectric constant for Interlayer Dielectric (ILD) applications, yet retaining thermal and mechanical integrity. We wish to report here our investigations on the preparation of ultra-low k ILD materials using a sacrificial approach whereby organic groups are burnt out to generate low k porous ORMOSIL films. We have been able to prepare a variety of organically modified silicone resins leading to highly microporous thin films, exhibiting ultra-low k from 1.80 to 2.87, and good to high modulus, 1.5 to 5.5 GPa. Structure property influences on porosity, dielectric constant and modulus will be discussed.     

Electrochemical Synthesis of a Microporous Conductive Polymer Based on a Metal–Organic Framework Thin Film

A new approach to preparing 3D microporous conductive polymer has been demonstrated in the electrochemical synthesis of a porous polyaniline network with the utilization of a MOF thin film supported on a conducting substrate. The prepared porous polyaniline with well‐defined uniform micropores of 0.84 nm exhibits a high BET surface area of 986 m² g^?1 and a high electric conductivity of 0.125 S cm^?1 when doped with I₂, which is superior to existing porous conducting materials of porous MOFs, CMPs, and COFs.     

Preparation and Characteristics of Porous Silica Films by a Modified Base-Catalyzed Sol-Gel Process Containing PVA: II. Film Preparation

Porous SiO₂ films were successfully deposited on silicon substrates by a modified base-catalyzed Sol-Gel process (MBCP) containing polyvinyl alcohol (PVA). The process conditions, such as the gelation time, the synthesis temperature, the stabilizing agent of the precursor solution and the spin coating speed, the heat-treatment, the annealing temperature of the film on the microstructure and porosity of porous SiO₂ films were systematically investigated by SEM, XRD and ellipsometry techniques. This study provides a novel preparation technique for the porous SiO₂ film. Using this process, the resultant film can reach a thickness of 3.6 m for one layer, a porosity of 25–50%, a low thermal conductivity of 0.11 W/m·K. This film will be used as a low dielectric layer, an thermal-insulating layer and a low refractive index layer.     

Undulated Multicompartment Cylinders by the Controlled and Directed Stacking of Polymer Micelles with a Compartmentalized Corona

Like a bamboo rod : Long, bamboo‐like undulated cylinders with distinct branch points and end groups (see picture) were obtained by the stacking of block terpolymer micelles that contain a fluorinated polybutadiene core and a compartmentalized corona of poly(4‐tert‐butoxystyrene) and poly(tert‐butyl methacrylate). Stacking of the polymer micelles, which can be reversed, occurred when the solvent was changed from dioxane to ethanol.

     

双偶极半菁衍生物／H4SiW12O40自组装多层膜的研究

通过交替吸附H_4SiW_(12)O_(40)和双偶极半菁衍生物制备了一个新颖的无机- 有机杂化自组装多层膜。紫外可见光谱和X射线衍射研究证实了半菁衍生物 /H_4SiW_(12)O_(40)多层膜可被均匀沉积厚达至少12层，具有平均膜厚5.3nm(半菁 阳离子层加SiW_(12)O_(40)~(4-)层)的二维有序结构，膜中半菁衍生物与H_4SiW_ (12)O_(40)间发生了较强的电荷转移作用。循环伏安研究表明，薄膜具有较好的电 化学活性。     

喷墨打印聚合物薄膜均匀性调控研究进展

聚合物发光显示材料具有发光颜色在全可见光区可调、可溶液简单加工及适用于柔性大面积基底的特点,成为目前研究的热点。 在聚合物发光薄膜图案化技术中,喷墨打印因为具有加工过程简单高效、适用于溶液方式加工、柔性的加工过程等特点而被认为是最具有应用潜力的技术。 高质量聚合物薄膜的制备是高精度发光显示器件制作的关键,但喷墨打印液滴在干燥过程中通常伴随着“咖啡环”现象,造成薄膜不均匀沉积。 因此,消除“咖啡环”现象,实现聚合物薄膜的均匀沉积,是喷墨打印高性能器件的重要研究方向。 本文主要论述了“咖啡环”效应的产生机理,如何抑制喷墨打印聚合物薄膜加工过程中的“咖啡环”效应,最终实现聚合物薄膜均匀性调控。     

A Novel Fibrous Material Created by Self‐Rolling of a Patterned Polymer Thin Film

A new kind of a fibrous material is produced by controlled self‐rolling of patterned thin poly(4‐vinyl)pyridine films in acidic water. Self‐rolling is induced by unequal swelling of the top and the bottom layers of the films in the solvent. Rolling starts from parallel scratches in the film and results in twin‐scroll fibers. The fibers are stabilized by staining with CuCl₂ salt and freeze‐dried. The output of the fiber material production is of the order of 1 cm³ from approximately 50 cm² of the patterned polymer film. The approach opens new broad opportunities for creation of smart fibrous materials via loading the fibers with functional micro‐ and nanoparticles.