Demonstration of a HeNe/CH4-based optical molecular clock

We implement a simple optical clock based on the F2(2) [P(7), v3] optical transition in methane. A single femtosecond laser's frequency comb undergoes difference frequency generation to provide an IR comb at 3.39 microm with a null carrier-envelope offset. This IR comb provides a phase-coherent link between the 88-THz optical reference and the rf repetition rate. Comparison of the repetition rate signal with a second femtosecond comb stabilized to molecular iodine shows an instability of 1.2 x 10(-13) at 1 s, limited by microwave detection of the repetition rates. The single-sideband phase noise of the microwave signal, normalized to a carrier frequency of 1 GHz, is below -93 dBc/Hz at 1-Hz offset.     

Ultralow phase noise microwave generation with an Er:fiber-based optical frequency divider

We present an optical frequency divider based on a 200 MHz repetition rate Er:fiber mode-locked laser that, when locked to a stable optical frequency reference, generates microwave signals with absolute phase noise that is equal to or better than cryogenic microwave oscillators. At 1 Hz offset from a 10 GHz carrier, the phase noise is below -100 dBc/Hz, limited by the optical reference. For offset frequencies >10 kHz, the phase noise is shot noise limited at -145 dBc/Hz. An analysis of the contribution of the residual noise from the Er:fiber optical frequency divider is also presented.     

Long-distance frequency dissemination with a resolution of 10(-17)

We use a new technique to disseminate microwave reference signals along ordinary optical fiber. The fractional frequency resolution of a link of 86 km in length is 10(-17) for a one day integration time, a resolution higher than the stability of the best microwave or optical clocks. We use the link to compare the microwave reference and a CO2/OsO4 frequency standard that stabilizes a femtosecond laser frequency comb. This demonstrates a resolution of 3 x 10(-14) at 1 s. An upper value of the instability introduced by the femtosecond laser-based synthesizer is estimated as 1 x 10(-14) at 1 s.     

Ultra-stable microwave generation with a diode-pumped solid-state laser in the 1.5-μm range

We demonstrate the first ultra-stable microwave generation based on a 1.5-μm diode-pumped solid-state laser (DPSSL) frequency comb. Our system relies on optical-to-microwave frequency division from a planar-waveguide external cavity laser referenced to an ultra-stable Fabry–Perot cavity. The evaluation of the microwave signal at ~10 GHz uses the transportable ultra-low-instability signal source ULISS^®, which employs a cryo-cooled sapphire oscillator. With the DPSSL comb, we measured ?125 dBc/Hz phase noise at 1 kHz offset frequency, likely limited by the photo-detection shot-noise or by the noise floor of the reference cryo-cooled sapphire oscillator. For comparison, we also generated low-noise microwave using a commercial Er:fiber comb stabilized in similar conditions and observed >20 dB lower phase noise in the microwave generated from the DPSSL comb. Our results confirm the high potential of the DPSSL technology for low-noise comb applications.     

Phase-locked widely tunable optical single-frequency generator based on a femtosecond comb

We present an arbitrary optical single-frequency generator based on a femtosecond optical frequency comb. The functions of this device are comparable to those of a radio-frequency synthesizer. However, this device operates at hundreds of terahertz. The absolute frequency accuracy of this synthesizer is approximately 1 kHz at a 282 THz carrier frequency. The stability is approximately 2 x 10(-14) at 100 s, and the tuning speed exceeds 30 GHz/s. This source demonstrates the integration of a phase-locked optical comb into a versatile and easy-to-use system for the generation of tunable, absolute optical frequencies. By using downconversion, one could generate tunable terahertz frequencies that are phase locked to a microwave reference, such as a Cs atomic clock, and high-precision interferometry could benefit greatly from the stability and accuracy of this widely tunable source.     

Widely tunable THz synthesizer

The generation of cw-THz radiation by photomixing is particularly suited to the high resolution spectroscopy of gases; nevertheless, until recently, it has suffered from a lack of frequency metrology. Frequency combs are a powerful tool that can transfer microwave frequency standards to optical frequencies and a single comb has permitted accurate (10⁻⁸) THz frequency synthesis with a limited tuning range. A THz synthesizer composed of three extended cavity laser diodes phase locked to a frequency comb has been constructed and its utility for high resolution gas phase spectroscopy demonstrated. The third laser diode allows a larger tuning range of up to 300 MHz to be achieved without the need for large frequency excursions, while the frequency comb provides a versatile link to be established from any traceable microwave frequency standard. The use of a single frequency comb as a reference for all of the cw-lasers eliminates the dependency of synthesized frequency on the carrier envelope offset frequency. This greatly simplifies the frequency comb stabilization requirements and leads to a reduced instrument complexity.     

Phase-locked, erbium-fiber-laser-based frequency comb in the near infrared

A phase-locked frequency comb in the near infrared is demonstrated with a mode-locked, erbium-doped, fiber laser whose output is amplified and spectrally broadened in dispersion-flattened, highly nonlinear optical fiber to span from 1100 to >2200 nm. The supercontinuum output comprises a frequency comb with a spacing set by the laser repetition rate and an offset by the carrier-envelope offset frequency, which is detected with the standard f-to-2f heterodyne technique. The comb spacing and offset frequency are phase locked to a stable rf signal with a fiber stretcher in the laser cavity and by control of the pump laser power, respectively. This infrared comb permits frequency metrology experiments in the near infrared in a compact, fiber-laser-based system.     

Frequency comb-referenced narrow line width diode laser system for coherent molecular spectroscopy

We analyze in detail the frequency noise properties of a grating enhanced external cavity diode laser (GEECDL). This system merges two diode laser concepts, the grating stabilized diode laser and the diode laser with resonant optical feedback, thus combining a large tuning range with an excellent short-term frequency stability. We compare the frequency noise spectrum of a GEECDL to that of a grating stabilized diode laser and demonstrate a 10-fold reduction of the frequency noise linear spectral density. The GEECDL is phase locked to a similar laser and to a fs-frequency comb with a servo loop providing an open-loop unity-gain frequency of only 237 kHz, which is a tenth of the bandwidth typically required for grating stabilized diode lasers. We achieve a residual rms phase error as small as 72 mrad (≈ 200 mrad) for stabilization to a similar laser (to the fs-frequency comb). We demonstrate that the novel diode laser can phase-coherently track a stable optical reference with an instability of 1.8×10^-16 at 1 s. This laser system is well suited for applications that require phase locking to a low-power optical reference under noisy conditions. It may also be considered for the implementation of optical clock lasers. PACS 42.55.Px; 42.60.Jf; 42.50.Gy     

Full phase stabilization of a Yb:fiber femtosecond frequency comb via high-bandwidth transducers

We present full phase stabilization of an amplified Yb:fiber femtosecond frequency comb using an intracavity electro-optic modulator and an acousto-optic modulator. These transducers provide high servo bandwidths of 580 kHz and 250 kHz for f(rep) and f(ceo), producing a robust and low phase noise fiber frequency comb. The comb was self-referenced with an f-2f interferometer and phase locked to an ultrastable optical reference used for the JILA Sr optical clock at 698 nm, exhibiting 0.21 rad and 0.47 rad of integrated phase errors (over 1 mHz-1 MHz), respectively. Alternatively, the comb was locked to two optical references at 698 nm and 1064 nm, obtaining 0.43 rad and 0.14 rad of integrated phase errors, respectively.     

Improved stabilization of a 1.3 microm femtosecond optical frequency comb by use of a spectrally tailored continuum from a nonlinear fiber grating

We report significant enhancement (+24 dB) of the optical beat note between a 657 nm cw laser and the second-harmonic generation of the tailored continuum at 1314 nm generated with a femtosecond Cr:forsterite laser and a nonlinear fiber Bragg grating. The same continuum is used to stabilize the carrier-envelope offset frequency of the Cr:forsterite femtosecond laser and permits improved optical stabilization of the frequency comb from 1.0 to 2.2 microm. Using a common optical reference at 657 nm, a relative fractional frequency instability of 2.0 x 10(-15) is achieved between the repetition rates of Cr:forsterite and Ti:sapphire laser systems in 10 s averaging time. The fractional frequency offset between the optically stabilized frequency combs of the Cr:forsterite and Ti:sapphire lasers is +/-(0.024 +/- 6.1) x 10(-17).     

Stabilized frequency comb with a self-referenced femtosecond Cr:forsterite laser

A frequency comb is generated with a Cr:forsterite femtosecond laser, spectrally broadened through a highly nonlinear optical fiber to span from 1.0 to 2.2 ,m, and stabilized using the f-to-2f self-referencing technique. The repetition rate and the carrier-envelope offset frequency are stabilized to a hydrogen maser, calibrated by a cesium atomic fountain clock. Simultaneous frequency measurement of a 657-nm cw laser by use of the stabilized frequency combs from this Cr:forsterite system and a Ti:sapphire laser agree at the 10(-13) level. The frequency noise of the comb components is observed at 1064, 1314, and 1550 nm by comparing the measured beat frequencies between cw lasers and the supercontinuum frequency combs.     

Precision phase control of an ultrawide-bandwidth femtosecond laser: a network of ultrastable frequency marks across the visible spectrum

We demonstrate that the stability of the current optical frequency comb generated by a Kerr-lens mode-locked femtosecond laser is limited by the microwave reference used for phase locking the comb spacing. Hence we implement precision frequency/phase control of the entire comb to the fundamental and second-harmonic frequencies of a stable cw laser without any external microwave reference. The stability of a cw iodine-stabilized laser is transferred to millions of comb lines (with an instability of 3 x 10(-13)) covering more than one octave of the optical frequency spectrum. In addition, the mode spacing of the comb can be used as a stable microwave frequency derived directly from a stable optical oscillator.     

A frequency-stabilized Yb:KYW femtosecond laser frequency comb and its application to low-phase-noise microwave generation

We present an optically stabilized Yb:KYW fs-laser frequency comb. We use an f–2f nonlinear interferometer to measure the carrier envelope offset frequency (f ₀) and the heterodyne beatnote between the comb and a stable CW laser at 1068 nm to detect fluctuations in the comb repetition rate ( $f_{\mathrm{rep}}$ f rep ). Both of these degrees of freedom of the comb are then controlled using phase-locked loops. As a demonstration of the frequency-stabilized comb, we generate low-phase-noise 10 GHz microwaves through detection of the pulse train on a high bandwidth photodiode. The phase noise of the resulting 10 GHz microwaves was ?99 dBc/Hz at 1 Hz and the corresponding Allen deviation was <2.6 × 10^?15 at 1 s, measured by comparison to an independently stabilized Ti:sapphire frequency comb. This room-temperature, optically based source of microwaves has close-to-carrier phase noise comparable to the very best cryogenic microwave oscillators.     

Highly stable,frequency-controlled mode-locked erbium fiber laser comb

A mode-locked Er:fiber laser-based optical frequency comb with high stability in the repetition frequency and carrier-envelope offset (CEO) frequency is realized. The CEO beat signal was detected right after the supercontinuum generation by a compact single-beam f–2f self-referencing interferometer, which does not require further delay compensation. The stabilized repetition frequency has an out-of-loop tracking stability of 1.3×10^-13/ for an integration time τ less than 1000 s, which is limited by the stability of the frequency measurement system. The stabilized CEO frequency has a residual fluctuation of 0.52 mHz measured with a 1 s gate time. This is, to our knowledge, the highest tracking stability realized for fiber laser-based optical frequency comb. PACS 06.30.Ft; 42.60.Lh; 42.55.Wd     

Frequency-stabilized Yb:fiber comb with a tapered single-mode fiber

We demonstrate a stable Yb:fiber frequency comb with supercontinuum generation by using a specially designed tapered single-mode fiber, in which a spectrum spanning from 500 nm to 1500 nm is produced. The carrier-envelope offset signal of the Yb:fiber comb is measured with a signal-to-noise ratio of more than 40 dB and a linewidth narrower than120 k Hz. The repetition rate and carrier-envelope offset signals are simultaneously phase locked to a microwave reference frequency.     

基于飞秒光频梳的双频He-Ne激光器频率测量

利用光纤飞秒光频梳和外腔可调谐半导体激光器, 建立了一套双频He-Ne激光器频率测量系统. 选用铷钟作为系统的频率基准, 通过将外腔半导体激光锁定至光频梳使得其频率溯源至铷钟, 再利用外腔可调谐半导体激光与双频He-Ne激光器输出的正交偏振激光拍频, 同时测量两路正交偏振激光频率. 将可调谐半导体激光器锁定至光频梳第1894449个梳齿, 其绝对频率为473612190000.0±2.7 kHz, 相对不确定度为5.7×10^-12. 对商品双频He-Ne激光器进行频率测量实验, 双频He-Ne激光器水平方向偏振激光频率均值为473612229934 kHz, 竖直方向偏振激光频率均值为473612232111 kHz, 平均时间为1024 s的相对Allan标准差为5.2×10^-11, 频差均值为2.177 MHz, 标准偏差为2 kHz.     

利用光频梳提高台阶高度测量准确度的方法

提出一种利用光频梳和可调谐半导体激光器提高台阶高度测量准确度的方法. 通过将可调谐激光器锁定至光频梳,可对激光器的输出波长进行精确锁定与测量.基于可调合成波长链原理,利用锁定后的半导体激光器构建了一套台阶高度测量方案,该方案可消除合成波长误差对台阶高度测量不确定度的影响. 采用一台可调谐半导体激光器和光频梳进行了5000 s的连续锁定实验, 结果表明,锁定后的可调谐半导体激光器的频率稳定度达 1.8×10^-12.该方法的理论测量不确定度约为7.9 nm, 且测量结果可溯源至时间频率基准.     

Phase-coherent link from optical to microwave frequencies by means of the broadband continuum from a 1-GHz Ti:sapphire femtosecondoscillator

An optical clockwork is created with a compact 1-GHz repetition-rate laser and three nonlinear crystals. The broadband continuum output of the laser covers sufficient bandwidth to provide direct access to its carrier-envelope offset frequency without the use of a microstructure fiber. We phase lock the femtosecond comb to a Ca optical standard and monitor the stability of the repetition rate, f(r) , at 1 GHz. We demonstrate that the short-term stability of the microwave output of the optical clock is at least as good as that of a high-performance hydrogen maser.     

Femtosecond-laser-based synthesis of ultrastable microwave signals from optical frequency references

We use femtosecond laser frequency combs to convert optical frequency references to the microwave domain, where we demonstrate the synthesis of 10-GHz signals having a fractional frequency instability of < or =3.5 x 10(-15) at a 1-s averaging time, limited by the optical reference. The residual instability and phase noise of the femtosecond-laser-based frequency synthesizers are 6.5 x 10(-16) at 1 s and -98 dBc/Hz at a 1-Hz offset from the 10-GHz carrier, respectively. The timing jitter of the microwave signals is 3.3 fs.     

利用锁相环和TV-Rb钟控制飞秒激光脉冲的载波包络相移

为了实现对锁模飞秒钛宝石激光器的相位控制，采用改进的相移测量装置，使载波包络频移信号的信噪比提高到了40 dB以上.在此优化测量结果的基础上，利用电子锁相环技术，通过PZT改变激光器腔内端镜的倾斜将飞秒激光脉冲的载波包络相位锁定到了微波参考源TV-Rb钟10 MHz标准信号上，同时激光脉冲重复频率也采用另一个PZT控制激光腔长锁定到了同一个TV-Rb钟10 MHz信号上.锁定后的结果显示重复频率的锁定达到了TV-Rb钟本身的稳定度，而载波包络相位锁定后比锁定前稳定度提高了三个数量级.