Identification and quantitation of pyrethroid pesticide residues in vegetables by solid-phase extraction and liquid chromatography/electrospray ionization ion trap mass spectrometry

A quantitative method consisting of solid-phase extraction (SPE) followed by liquid chromatography/electrospray ionization ion trap mass spectrometry (LC/ESI-ITMS) analysis was developed for the identification and quantitation of ten pyrethroid pesticides commonly used in vegetables. The best HPLC separation was achieved using a gradient program of methanol/water mixture. For the vegetable samples, an SPE procedure to clean up the matrices was carried out prior to LC/MS analysis. Under the optimum conditions, the limits of quantification of the pyrethroid pesticides (tetramethrin, allethrin, fenpropathrin, lambda-cyhalothrin, cypermethrin, deltamethrin, fenvalerate, bioresmethrin, permethrin and bifenthrin) ranged from 0.03 to 0.1 mg kg-1 with relative standard deviations<20%, and the mean recoveries ranged from 69.5 to 102.5%. The proposed method has been successfully applied to the determination of pyrethroids in six vegetables with satisfactory results.     

Determination of Pyrethroids in Dendrobium officinale by Ultrasound/Microwave-Assisted Solid–Liquid–Solid Dispersive Extraction,Gas Chromatography,and Triple-Quadrupole Mass Spectrometry

An ultrasound/microwave-assisted solid–liquid–solid dispersive extraction method was developed for the determination of 16 pyrethroid insecticides in Dendrobium officinale. The extraction and purification were performed in one step. The pyrethroids were extracted with 8:2 acetone:hexane and purified with a mixture of primary secondary amine, Florisil, C18, and graphitized carbon black. The extraction temperature, extraction time, and ultrasound power were optimized. Trans-cyfluthrin-d₆ was used as the internal standard to improve the accuracy. Under the optimized conditions, the recoveries of the pyrethroids were from 72.2 to 113.9% with the limits of detection between 0.29 and 9.38?µg?kg^?1. The optimized method was successfully used for the determination of pyrethroids in commercial D. officinale samples and may allow monitoring pyrethroids in herbal products.     

Microwave-assisted extraction of pyrethroid insecticides from semi permeable membrane devices (SPMDs) used to indoor air monitoring

A rapid and environmentally friendly methodology was developed for the extraction of pyrethroid insecticides from semi permeable membrane devices (SPMDs), in which they were preconcentrated in gas phase. The method was based on gas chromatography mass–mass spectrometry determination after a microwave-assisted extraction, in front of the widely employed dialysis method. SPMDs were extracted twice with 30 mL hexane:acetone, irradiated with 250 W power output, until 90 °C in 10 min, this temperature being held for another 10 min. Clean-up of the extracts was performed by acetonitrile–hexane partitioning and solid-phase extraction (SPE) with a combined cartridge of 2 g basic-alumina, deactivated with 5% water, and 500 mg C₁₈.

Pyrethroids investigated were Allethrin, Prallethrin, Tetramethrin, Bifenthrin, Phenothrin, λ-Cyhalothrin, Permethrin, Cyfluthrin, Cypermethrin, Flucythrinate, Esfenvalerate, Fluvalinate and Deltamethrin. The main pyrethroid synergist compound, Pyperonyl Butoxide, was also studied. Limit of detection values ranging from 0.3 to 0.9 ng/SPMD and repeatability data, as relative standard deviation, from 2.9 to 9.4%, were achieved. Pyrethroid recoveries, for spiked SPMDs, with 100 ng of each one of the pyrethroids evaluated, were from 61 ± 8 to 103 ± 7% for microwave-assisted extraction, versus 54 ± 4 to 104 ± 3% for dialysis reference method. Substantial reduction of solvent consumed (from 400 to 60 mL) and analysis time (from 48 to 1 h) was achieved by using the developed procedure.

High concentration levels of pyrethroid compounds, from 0.14 to 7.3 μg/SPMD, were found in indoor air after 2 h of a standard application.     

Off-line coupling of pressurized liquid extraction and LC/ED for the determination of retinyl acetate and tocopherols in infant formulas

An analytical methodology including pressurized liquid extraction (PLE) as sample treatment to isolate retinyl acetate and tocopherols from infant formulas has been developed. The milk extracts were kept at −18 °C for 30 min and after filtration could be injected directly into the chromatographic system. Thus, a rapid and simple routine control method of these products is possible.

The parameters affecting both the extraction process and the liquid chromatography (LC) system were optimized. PLE was performed using one cycle of extraction during a static time of 5 min. Methanol was chosen as the extraction solvent for a temperature of 50 °C. Chromatographic separation was accomplished using a RP-18 column; the mobile phase used was methanol–water (94:6, v/v) containing 2.5 mM acetic acid/sodium acetate buffer. Electrochemical detection in amperometric mode with a glassy carbon electrode at +1100 mV was applied. The proposed methodology was successfully used for the determination of retinyl acetate, δ-tocopherol, (β + γ)-tocopherol and -tocopherol in different infant formulas. The analytes were evaluated in the same chemical form present in the samples. Recoveries were between 92 and 106%. A certified reference material of milk powder was also analyzed.     

固相萃取-气相色谱-质谱法测定木制家具中氯酚类及菊酯类防腐剂

建立了固相萃取-气相色谱-质谱(SPE-GC-MS)检测含氯酚类化合物(2,4-二氯苯酚、2,4,6-三氯苯酚、2,4,5-三氯苯酚、2,3,4,6-四氯苯酚、五氯苯酚、林丹)和菊酯类化合物(氯菊酯、氟氯氰菊酯、氯氰菊酯、溴氰菊酯)等10种木材防腐剂的方法。对家具样品采用超声萃取法、以甲醇为提取剂在室温下反复提取2次,提取液经浓缩后,加入碳酸钾和乙酰酐衍生化,将衍生化后的溶液通过Oasis HLB固相萃取柱净化,用乙酸乙酯洗脱并收集检测。采用该方法实现了家具中10种木材防腐剂的分离检测,该方法中氯酚类防腐剂定量限为1 mg/kg、菊酯类防腐剂定量限为5 mg/kg,平均回收率为76.0%～108.8%。应用该方法对市场上销售的木制家具进行了检测,在部分家具中检出含有少量林丹。实验结果证明,该方法准确、灵敏,可有效地应用于木制家具中防腐剂的实际检验工作中。     

A rapid and sensitive analytical method for the determination of 14 pyrethroids in water samples

A simple, efficient and environmentally friendly analytical methodology is proposed for extracting and preconcentrating pyrethroids from water samples prior to gas chromatography-negative ion chemical ionization mass spectrometry (GC-NCI-MS) analysis. Fourteen pyrethroids were selected for this work: bifenthrin, cyfluthrin, λ-cyhalothrin, cypermethrin, deltamethrin, esfenvalerate, fenvalerate, fenpropathrin, τ-fluvalinate, permethrin, phenothrin, resmethrin, tetramethrin and tralomethrin. The method is based on ultrasound-assisted emulsification-extraction (UAEE) of a water-immiscible solvent in an aqueous medium. Chloroform was used as extraction solvent in the UAEE technique. Target analytes were quantitatively extracted achieving an enrichment factor of 200 when 20 mL aliquot of pure water spiked with pyrethroid standards was extracted. The method was also evaluated with tap water and river water samples. Method detection limits (MDLs) ranged from 0.03 to 35.8 ng L⁻¹ with RSDs values ≤3–25% (n = 5). The coefficients of estimation of the calibration curves obtained following the proposed methodology were ≥0.998. Recovery values were in the range of 45–106%, showing satisfactory robustness of the method for analyzing pyrethroids in water samples. The proposed methodology was applied for the analysis of river water samples. Cypermethrin was detected at concentration levels ranging from 4.94 to 30.5 ng L⁻¹.     

Trace-level determination of pyrethroid,neonicotinoid and carboxamide pesticides in beeswax using dispersive solid-phase extraction followed by ultra-high-performance liquid chromatography-tandem mass spectrometry

The aim of the work was to develop an analytical procedure able to quantify traces of 13 neonicotinoids and pyrethroids as well as carboxamide in beeswax at low levels (ng g^?1) to evaluate the contamination. For this purpose, an efficient sample preparation procedure was developed based on solid–liquid extraction using dispersive diatomaceous earth and acetonitrile. This step was followed by a selective and sensitive analysis based on ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (ESI-MS/MS). This analytical procedure was validated based on International Conference on Harmonization guidelines. The limits of quantification ranged from 1 ng g^?1 (thiamethoxam, clothianidin, imidacloprid, acetamiprid, thiacloprid and boscalid) to 40 ng g^?1 (lambda-cyhalothrin). The method was then successfully applied to 60 samples of beeswax collected in several areas of France. The presence of thiacloprid, boscalid, imidacloprid and deltamethrin in beeswax was confirmed. The most frequently quantified pesticide was boscalid.     

A cleanup method for perchlorate determination in urine

There is increasing concern about perchlorate exposure because of perchlorate's potential effects on organisms as a thyroid hormone disruptor, as well as its contamination of the environment being much more widespread than previously thought. Perchlorate is excreted primarily into urine, therefore, evaluating perchlorate residues in urine should be a reasonable approach for determining exposure and if successful could be used as an effective biomarker of perchlorate exposure. Since the presence of ions and other biomolecules in matrices like urine usually confounds accurate determination of perchlorate by ion chromatography, it is necessary to develop efficient methods for perchlorate determination in these matrices. We developed a method that reduces the background signal of urine, which is typically the problem with the analysis of biological fluids and tissues by ion chromatography. Relatively high recovery of perchlorate was shown. In cow urine samples spiked with perchlorate at 2.5, 10, and 100 μg/L, perchlorate recoveries were 67% ± 2.5, 77% ± 3.6, and 81% ± 1.7 (mean ± S.D.), respectively. In addition, the detection limit was as low as 12.6, 12.3, and 18.7 μg/L in cow, vole, and human urine samples, respectively.     

Development of a solid-phase microextraction gas chromatography with microelectron-capture detection method for a multiresidue analysis of pesticides in bovine milk

A simple and rapid method based on solid-phase microextraction (SPME) technique followed by gas chromatography with microelectron-capture detection (GC-microECD) was developed for the simultaneous determination of more than 30 pesticides (pyrethroids and organochlorinated among others) in milk. To our knowledge, this is the first application of SPME for the determination of pyrethroid pesticides in milk. Negative matrix effects due to the complexity and lipophility of the studied matrix were reduced by diluting the sample with distilled water. A 2(5-1) fractional factorial design was performed to assess the influence of several factors (type of fiber coating, sampling mode, stirring, extraction temperature, and addition of sodium chloride) on the SPME procedure and to determine the optimal extraction conditions. After optimization of all the significant variables and interactions, the recommended procedure was established as follows: DSPME (using a polydimethylsiloxane (PDMS)/divinylbenzene (DVB) coating) of 1 mL of milk sample diluted with Milli-Q water (1:10 dilution ratio), at 100 degrees C, under stirring for 30 min. The proposed method showed good linearity and high sensitivity, with limits of detection (LOD) at the sub-ng mL(-1) level. Within a day and among days precisions were also evaluated (R.S.D.<15%). One of the most important attainments of this work was the use of external calibration with milk-matched standards to quantify the levels of the target analytes. The method was tested with liquid and powdered milk samples with different fat contents covering the whole commercial range. The efficiency of the extraction process was studied at several analyte concentration levels obtaining high recoveries (>80% in most cases) for different types of full-fat milks. The optimized procedure was validated with powdered milk certified reference material, which was quantified using external calibration and standard addition protocols. Finally, the DSPME-GC-microECD methodology was applied to the analysis of milk samples collected in farms of dairy cattle from NW Spain.     

Automatic determination of insolubles in lubricating oils by flow injection analysis employing an LED-photometer detector

A flow injection system is presented for the determination of the insolubles content in used lubricating oil samples. The system is based on the injection of an aliquot of the sample in a stream of organic solvent where it is dispersed, and measurement of the scattered radiation (measured as apparent absorbance) in the visible range (λ = 640 nm). An LED-based photometer was used for this purpose. The whole system including sample injection and data acquisition was controlled by a personal computer. Calibration curves exhibited good linearity (h = 0.415 ± 0.016C + 0.00 ± 0.03, r² = 0.9995, confidence level of 95%) in the range up to 2.68% (insolubles in pentane). Detection and quantification limits were respectively 0.07% and 0.16% (w/w). The method was validated by analysis of 25 real samples by the proposed method and the FTIR method finding high correlation. Waste generation and reactive consumption is much less than in the official method (ASTM D-893). The proposed method employs 25 mL of kerosene per sample while the official method employs 200 mL of pentane.     

The use of silica‐coated magnetic graphene microspheres as the adsorbent for the extraction of pyrethroid pesticides from orange and lettuce samples followed by GC–MS analysis

Graphene‐grafted ferroferric oxide microspheres were used as the adsorbent to extract some pyrethroid pesticides (bifenthrin, λ‐cyhalothrin, cyfluthrin, cypermethrin, fenvalerate, and deltamethrin) from orange and lettuce samples prior to their determination by GC–MS. The main variables that could affect the extraction, including the amount of the adsorbent, pH of the sample solution, extraction time, concentration of salt, and desorption conditions, were investigated and optimized. Under the optimized conditions, a linear response was obtained in the concentration range of 0.3–100.0 ng/g for the analytes with the coefficients of determination ranging from 0.9877 to 0.9925. The LODs for the pyrethroids ranged from 0.01 to 0.02 ng/g. The method provided a good repeatability with RSDs < 10.6%. The recoveries for the six pyrethroid pesticides were in the range from 90.0 to 103.7%. The method was applied to the determination of the pesticides in orange and lettuce samples with a satisfactory result.     

Application of solid-phase microextraction for determination of pyrethroids in groundwater using liquid chromatography with post-column photochemically induced fluorimetry derivatization and fluorescence detection

Solid-phase microextraction (SPME) is a rapid and simple analytical technique which uses coated fused-silica fibers to extract analytes from aqueous samples. This study develops a method of SPME analysis for seven pyrethroids, including fenpropathrin, lambda-cyhalothrin, deltamethrin, fenvalerate, permethrin, tau-fluvalinate and bifenthrin in groundwater samples using high performance liquid chromatography combined with post-column photochemically induced fluorimetry derivatization and fluorescence detection (SPME-LC-PIF-FD). To perform the SPME, a 60 microm polydimethylsiloxane/divinylbenzene (PDMS/DVB) fiber was used for the extraction of the pesticides from groundwater samples. The main factors affecting the SPME process, such as extraction time, stirring rate, extraction temperature, pH and the desorption process were studied. The use of photochemically induced fluorescence for detection improved sensitivity and selectivity. The limits of quantification (LOQs) obtained in the matrix, with respect to EURACHEM Guidance, varied between 0.03 and 0.075 microgL(-1). Relative recoveries ranged from 92 to 109% and relative standard deviations values ranged from 2 to 9%.     

Removal of humic matter interference in the determination of Cr(VI) in soil extracts by the diphenylcarbazide method

Alkaline digestion of soil samples, which is recommended for minimizing Cr(III)–Cr(VI) interconversions during the extraction of Cr(VI), may also solubilize humic matter (HM). The latter is responsible for both positive and negative interference in the analysis of Cr(VI) in the extract by the diphenylcarbazide (DPC) method. Humic compounds indeed absorb light at 540 nm as the Cr-DPC product and are also able to rapidly reduce Cr(VI) under the pH conditions of the standard DPC method. To prevent any risk of interference and make the DPC method applicable to soil extracts, a new protocol is proposed. This consists of three successive steps: (1) extraction of Cr(VI) by the U.S.EPA method 3060A in the presence of Mg²⁺; (2) batch removal of solubilised HM by the XAD-7 sorbent at pH 3.0 ± 0.1 with 3–5 min contact time; (3) analysis of Cr(VI) with the DPC method at pH 3.0 ± 0.1. The application of this new protocol to the soil product SQC-012 Lot 4 certified by R.T. Corporation (RTC, USA) gave significantly lower Cr(VI) concentrations and smaller variability compared to certified values (46.5 ± 2.3 instead of 153 ± 32.6 mg/kg). The new protocol was validated by Cr(VI) and Cr(III) spikes either to the soil/extractant suspension or to the exctract. Cr(VI) results in the wide range of acceptance limits (104–202 mg/kg) reported by RTC were only obtained when the U.S.EPA method 3060A without the addition of Mg²⁺ and DPC analysis at pH 1.0 were applied. The latter procedure appears questionable since it leads to largely variable results which reflect the complex role played by humic matter in the determination of Cr(VI) and the instability of Cr(III) during the extraction.     

Simultaneous determination of pyrethroids from pesticide residues in porcine muscle and pasteurized milk using GC

The principal goal of this work was to develop an efficient method for the simultaneous determination of four pyrethroid (PYR) insecticides, cyfluthrin, cyhalothrin, cypermethrin, and deltamethrin, in porcine muscle and pasteurized milk using liquid–liquid extraction (LLE). Sample extraction was carried out with and without additional column cleanup procedures, and the final determination was made using GC with electron‐capture detector (ECD). The pesticide identity was confirmed using GC‐MS in the SIM mode. Since there were minor differences between the extraction procedures, extraction without the additional cleanup procedure was used throughout the work. The method was validated by fortifying blank samples with half, two, and four times the maximum residue limit (MRL) of each PYR. The average recoveries (n = 6) ranged from 83.5 to 99.2% and 82.9 to 109% in porcine muscle and pasteurized milk, respectively. The repeatability of measurements expressed as RSDs, was in the range of 1.7–11.9 and 1.5–10.3% in porcine muscle and pasteurized milk, respectively. The LODs ranged from 3.3 to 9 and 3 to 8.1 ppm, whereas the LOQs ranged from 10 to 27.4 and 9 to 24.6 ppm, in porcine muscle and pasteurized milk, respectively. The applicability of the method was demonstrated by analyzing real samples collected from major cities in the Republic of Korea. No residues of the selected pesticides were detected in any of the samples.     

Occurrence of aflatoxin M1 in milk samples from Italy analysed by online-SPE UHPLC-MS/MS

The occurrence of aflatoxin M1 in 69 milk samples collected in a south region of Italy in 2016 was evaluated. The samples were analysed using an automated method based on online SPE coupled with UHPLC tandem mass spectrometry. After a salt induced liquid–liquid extraction with acetonitrile to remove protein from milk, the extract was diluted with water and analysed using an automated online SPE MS/MS method. Among the analysed samples no one had AFM1 higher than the legally allowable limits whereas 71.4% of the other analysed samples were above the LOD of the method. The highest contamination level of AFM1 was found in pasteurised milk (44.39 ng kg^?1). The results show the worrying and widespread of AFM1 contamination, highlighting the necessity of monitoring studies in order to evaluate the reduction of the maximum legal limit.     

Optimisation of sample treatment for arsenic speciation in alga samples by focussed sonication and ultrafiltration

A procedure for arsenic species fractionation in alga samples (Sargassum fulvellum, Chlorella vulgaris, Hizikia fusiformis and Laminaria digitata) by extraction is described. Several parameters were tested in order to evaluate the extraction efficiency of the process: extraction medium, nature and concentration (tris(hydroxymethyl)aminomethane, phosphoric acid, deionised water and water/methanol mixtures), extraction time and physical treatment (magnetic stirring, ultrasonic bath and ultrasonic focussed probe). The extraction yield of arsenic under the different conditions was evaluated by determining the total arsenic content in the extracts by ICP-AES. Arsenic compounds were extracted in 5 mL of water by focussed sonication for 30 s and subsequent centrifugation at 14,000 × g for 10 min. The process was repeated three times. Extraction studies show that soluble arsenic compounds account for about 65% of total arsenic.

An ultrafiltration process was used as a clean-up method for chromatographic analysis, and also allowed us to determine the extracted arsenic fraction with a molecular weight lower than 10 kDa, which accounts for about 100% for all samples analysed.

Speciation studies were carried out by HPLC–ICP-AES. Arsenic species were separated on a Hamilton PRP-X100 column with 17 mM phosphate buffer at pH 5.5 and 1.0 mL min⁻¹ flow rate. The chromatographic method allowed us to separate the species As(III), As(V), MMA and DMA in less than 13 min, with detection limits of about 20 ng of arsenic per species, for a sample injection volume of 100 μL. The chromatographic analysis allowed us to identify As(V) in Hizikia (46 ± 2 μg g⁻¹), Sargassum (38 ± 2 μg g⁻¹) and Chlorella (9 ± 1 μg g⁻¹) samples. The species DMA was also found in Chlorella alga (13 ± 1 μg g⁻¹). However, in Laminaria alga only an unknown arsenic species was detected, which eluted in the dead volume.     

Flow-injection determination of total organic fluorine with off-line defluorination reaction on a solid sorbent bed

Considering recent reports on widespread occurrence and concerns about perfluoroalkyl substances (PFAS) in environmental and biological systems, analysis of these compounds have gained much attention in recent years. Majority of analyte-specific methods are based on a LC/MS/MS or a GC/MS detection, however many environmental or biological studies would benefit from a total organic fluorine (TOF) determination. Presented work was aimed at developing a method for TOF determination. TOF is determined as an amount of inorganic fluoride obtained after defluorination reaction conducted off-line using sodium biphenyl reagent directly on the sorbent without elution of retained analytes. Recovered fluoride was analyzed using flow-injection system with either fluorimetric or potentiometric detection. The TOF method was tested using perfluorocarboxylic acids (PFCA), including perfluorooctanoic acid (PFOA), as model compounds. Considering low concentrations of PFAS in natural samples, solid-phase extraction as a preconcentration procedure was evaluated. Several carbon-based sorbents were tested, namely multi-wall carbon nanotubes, carbon nanofibres and activated carbon. Good sorption of all analytes was achieved and defluorination reaction was possible to carry out directly on a sorbent bed. Recoveries obtained for PFCAs, adsorbed on an activated carbon sorbent, and measured as TOF, were 99.5 ± 1.7, 110 ± 9.4, 95 ± 26, 120 ± 32, 110 ± 12 for C4, C6, C8, C10 and C12-PFCA, respectively. Two flow systems that would enable the defluorination reaction and fluoride determination in a single system were designed and tested.     

Rapid preconcentration method for the determination of pyrethroid insecticides in vegetable oils and butter fat and simultaneous determination by gas chromatography-electron capture detection and gas chromatography-mass spectrometry

A simple and rapid solid-phase extraction (SPE)-GC method for the preconcentration and quantification of pyrethroids at low nanogram levels in oils and high fat content samples is presented. The method was studied using seven highly persistent pyrethroid insecticides, viz., cypermethrin, deltamethrin, fenvalerate, cyfluthrin, allethrin, cyhalothrin and permethrin. Preconcentration was achieved by treating the oil samples with methyltrioctylammonium chloride and subsequent elution of the pyrethroid molecules from a graphitized carbon black SPE cartridge using 5 ml of acetonitrile. Pyrethroid quantification was achieved by GC with electron capture detection. Recoveries of the pyrethroids at fortification levels of 0.05-0.5 ppm were 94-105%. Storage on graphitized carbon black for 30 d lowered the recovery of the pyrethroids by only 3-6%. The method compared well with results obtained by a GC-MS method. The relative standard deviation at a concentration level of 0.05-0.2 microgram ml-1 ranged from 1.31 to 5.16%. The limit of detection achieved was 0.002 microgram ml-1 without any additional clean-up and with little interference from lipids during analysis.     

Comparison of AFS and ICP-MS detection coupled with gas chromatography for the determination of methylmercury in marine samples

Inductively coupled plasma mass spectrometry (ICP-MS) and atomic fluorescence spectrometry (AFS) coupled with gas chromatography (GC) have been evaluated as element specific detectors for the determination of methylmercury in marine samples. Detection limits for methylmercury chloride, obtained using ICP-MS and AFS, were 0.9 and 0.25 pg as Hg, respectively. Methylmercury was determined in marine tissue reference materials IAEA 142 and NIST 8044 mussel homogenate, and DOLT-2 dogfish liver by GC–AFS, with found values of 45±7, 26±4, and 671±41 ng g⁻¹, compared with certified values of 47±4, 28±2, and 693±53 ng g⁻¹. The analyses of IAEA 142 and NIST 8044 were repeated using GC–ICP-MS, with found values of 48±9 and 30±3 ng g⁻¹, respectively. Methylmercury was determined in real samples of ringed seal and beluga whale, with found values of 801±62 and 2830±113 ng g⁻¹, respectively.     

纳米纤维在分析菊酯类农药残留中的应用

以电纺聚苯乙烯纳米纤维作固相萃取材料,对茶叶样品中的拟除虫菊酯农药进行分离富集,用气相色谱-电子捕获器进行检测,并对影响纤维萃取效率的因素进行优化,联苯菊酯、氯菊酯、氰戊菊酯、溴氰菊酯和甲氰菊酯在纳米纤维柱上的最大吸附量分别为7.8、7.5、7.2、6.6、7.0μg/mg,5种农药的3种标准混合液通过纳米纤维小柱后回收率为65.5%～89.0%,RSD为1.2%～3.0%。测定喷洒5种农药后的茶叶样品添加回收率为61.3%～87.1%,RSD为0.9%～2.8%,方法的测定下限为1.0×10-4～1.0×10-2mg/kg。该方法可以满足茶叶中拟除虫菊酯类农药残留检测的要求。