不同形貌Bi4Ti3O12粒子的可控合成及光催化性能

研究了用一步水热法制备的不同形貌的钛酸铋(Bi₄Ti₃O₁₂, BIT)粒子的光学和可见光催化性能, 并对其晶体结构和微观结构用X射线衍射(XRD)、场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)和高分辨透射电子显微镜(HRTEM)等手段进行了表征. XRD结果表明, 所制备的BIT 样品为层状钙钛矿结构. FESEM结果表明, 通过控制水热过程的反应参数可以得到不同形貌的纳米粒子. 紫外-可见漫反射光谱(UV-Vis DRS)表明BIT 样品的带隙能约为2.88-2.93 eV. 利用可见光(λ>420 nm)照射下的甲基橙(MO)降解实验评价了BIT 样品的光催化性能. 结果表明, BIT 的光催化活性比掺氮TiO₂ (N-TiO₂)高得多. 研究了形貌对BIT 光催化性能的影响. 所制备的BIT纳米带光催化效率最高, 经可见光照射360 min, 甲基橙溶液的降解率可达到95.0%.     

Synthesis and electrochemical properties of spinel LiMn2O4 prepared by the rheological phase method

Pure-phase and well-crystallized spinel LiMn₂O₄ powders were successfully synthesized by a simple rheological phase method. The thermal behavior and structure properties of the powders prepared by the rheological phase method compared with the solid-state reaction were investigated by thermogravimetry, powder X-ray diffraction , scanning electron microscopy and transmission electron microscopy. According to the results of the electrochemical tests, it is obvious that the sample resulting from the rheological phase method shows higher discharge capacity and better cycling stability than one formed in the solid-state reaction. The cyclic voltammogram and columbic efficiency curves also confirm that the product by the rheological phase method has a good cycling performance due to its fine cubic spinel structure and morphology.     

火焰辅助热解方法制备Ag_2O/TiO_2及其光催化制氢性能

以钛酸丁酯和硝酸银为前驱体,采用一步火焰辅助热解法制备了Ag_2O/TiO_2光催化剂并研究了样品在紫外-可见光照射下的光催化制氢性能。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)和紫外-可见漫反射吸收光谱(UV-Vis DRS)对样品进行了表征。XRD结果表明TiO_2均为锐钛矿晶型,Ag的引入对XRD结果无明显影响。SEM图显示未修饰的TiO_2是微球形貌,随着引入Ag含量的增加,微球减少直至消失。通过XPS分析和化学沉淀法表明样品中Ag的存在形式为Ag_2O。UV-Vis DRS测试发现引入Ag后提高了样品的光吸收。前驱体中Ag的量影响样品的光催化活性,最高的光催化制氢的活性可以达到相同条件下的P25的15倍。对光催化反应后的样品进行分析,认为在光催化过程中部分Ag_2O通过光生电子转化为Ag形成Ag/TiO_2,进一步提高光催化制氢活性。     

火焰辅助热解方法制备Ag2O/TiO2及其光催化制氢性能

以钛酸丁酯和硝酸银为前驱体,采用一步火焰辅助热解法制备了Ag₂O/TiO₂光催化剂并研究了样品在紫外-可见光照射下的光催化制氢性能。利用X射线衍射（XRD）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线光电子能谱（XPS）和紫外-可见漫反射吸收光谱（UV-Vis DRS）对样品进行了表征。XRD结果表明TiO₂均为锐钛矿晶型,Ag的引入对XRD结果无明显影响。SEM图显示未修饰的TiO₂是微球形貌,随着引入Ag含量的增加,微球减少直至消失。通过XPS分析和化学沉淀法表明样品中Ag的存在形式为Ag₂O。UV-Vis DRS测试发现引入Ag后提高了样品的光吸收。前驱体中Ag的量影响样品的光催化活性,最高的光催化制氢的活性可以达到相同条件下的P25的15倍。对光催化反应后的样品进行分析,认为在光催化过程中部分Ag₂O通过光生电子转化为Ag形成Ag/TiO₂,进一步提高光催化制氢活性。     

四角星形BiVO4/Bi2O3催化剂的制备及性能

采用水热法合成具有四角星形貌的钒酸铋,再将钒酸铋浸渍在碱溶液里二次水热,制备出BiVO_4/Bi_2O_3催化剂。采用X射线粉末衍射(XRD)、扫描电子显微镜(SEM),紫外-可见漫反射(UV-Vis DRS)等方法对样品进行表征。可见光下,BiVO_4/Bi_2O_3复合物的光催化降解罗丹明B性能及光电流响应均优于纯BiVO_4。这是由于BiVO_4/Bi_2O_3复合材料形成了异质结构,有效抑制了光生电子与空穴的复合效率。     

四角星形BiVO4/Bi2O3催化剂的制备及性能研究

采用水热法合成具有四角星形貌的钒酸铋,再将钒酸铋浸渍在碱溶液里二次水热,制备出BiVO₄/Bi₂O₃催化剂。采用X射线粉末衍射(XRD)、扫描电子显微镜(SEM),紫外-射(UV-Vis DRS)等方法征。可见光下,BiVO₄/Bi₂O₃复合物的光催化降解丹明B性能及光电优于纯BiVO₄。BiVO₄/Bi₂O₃复合材料形成了异质结构,有效抑制了光电子与空穴的复合效率。     

Visible-light-driven photocatalyst of Bi2WO6 nanoparticles prepared via amorphous complex precursor and photocatalytic properties

The visible-light-driven photocatalyst Bi₂WO₆ nanoparticles have been prepared by calcining amorphous complex precursor at a relatively low temperature of above 450 ^oC. The effects of calcination temperature and time on the structures and properties of Bi₂WO₆ nanoparticles have been investigated in detail. The photocatalytic activity of the Bi₂WO₆ powders were evaluated by degradation of RhB molecules in water under visible light irradiation (λ>400 nm). The results showed that the particle size and grain size of Bi₂WO₆ increased with the calcination temperature and time. The photocatalytic activity of the best sample was about 8.8 times higher than that of the sample prepared by traditional solid state reaction and the photo-degradations was a zero-order reaction. The best route to enhance the photocatalytic activity of Bi₂WO₆ was to prepare the sample at a lower temperature for a longer time, due to the samples with better crystallization and smaller particle size.     

中空Ta_2O_5/TiO_2复合光催化剂的可控氧化制备及性能

以钛粉、钽粉为原料,炭黑作为反应性模板,通过熔盐法在炭黑表面原位生长了TaTiC_2纳米碳化物涂层,并以所得TaTiC_2/C复合物为碳化物前驱体,再经可控氧化制备出中空Ta_2O_5/TiO_2复合光催化剂。采用X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、紫外-可见(UV-Vis)漫反射(DRS)及N2物理吸附等手段对所制备的光催化剂进行形貌、显微结构及孔结构表征。以高压汞灯为紫外光源,以亚甲基蓝为目标降解物,通过光催化降解实验评价中空Ta_2O_5/TiO_2复合光催化剂的光催化活性。结果表明,熔盐法生长碳化物涂层厚度均匀(20~30 nm),碳化物主要以TaTiC_2晶相存在且具有纳米级的颗粒尺寸。中空Ta_2O_5/TiO_2复合光催化剂同时具有200 nm左右的中空大孔结构及壳层10 nm左右的介孔结构。中空大孔和介孔的存在提高了所制备催化剂对亚甲基蓝的吸附能力。此外,TiO_2与Ta2O5通过电子能带结构的耦合,有效提高了光生电子和空穴的分离效率,从而显著提高了光催化活性。nTi∶nTa=2.5∶1.5时,相应的中空Ta_2O_5/TiO_2复合光催化剂表现出最佳的光催化活性,对亚甲基蓝的紫外光催化降解率高达97%。     

中空Ta2O5/TiO2复合光催化剂的可控氧化制备及性能

以钛粉、钽粉为原料,炭黑作为反应性模板,通过熔盐法在炭黑表面原位生长了TaTiC₂纳米碳化物涂层,并以所得TaTiC₂/C复合物为碳化物前驱体,再经可控氧化制备出中空Ta₂O₅/TiO₂复合光催化剂。采用X射线粉末衍射（XRD）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）、紫外-可见（UV-Vis）漫反射（DRS）及N₂物理吸附等手段对所制备的光催化剂进行形貌、显微结构及孔结构表征。以高压汞灯为紫外光源,以亚甲基蓝为目标降解物,通过光催化降解实验评价中空Ta₂O₅/TiO₂复合光催化剂的光催化活性。结果表明,熔盐法生长碳化物涂层厚度均匀（20~30 nm）,碳化物主要以TaTiC₂晶相存在且具有纳米级的颗粒尺寸。中空Ta₂O₅/TiO₂复合光催化剂同时具有200 nm左右的中空大孔结构及壳层10 nm左右的介孔结构。中空大孔和介孔的存在提高了所制备催化剂对亚甲基蓝的吸附能力。此外,TiO₂与Ta₂O₅通过电子能带结构的耦合,有效提高了光生电子和空穴的分离效率,从而显著提高了光催化活性。n_Ti∶n_Ta=2.5∶1.5时,相应的中空Ta₂O₅/TiO₂复合光催化剂表现出最佳的光催化活性,对亚甲基蓝的紫外光催化降解率高达97%。     

Li3V2(PO4)3的溶胶-凝胶法合成及其性能研究

以LiOH·H₂O、NH₄VO₃、H₃PO₄和柠檬酸等为原料采用溶胶-凝胶法合成了锂离子二次电池正极材料磷酸钒锂(Li₃V₂(PO₄)₃)。考察了煅烧温度和配位剂种类等条件对产物组成及电化学性能的影响。研究了优化条件下制得样品的循环伏安、充放电性能和循环性能。0.1 C条件下,样品首次放电比容量达129.81 mAh·g^-1，经过100次循环后容量几乎没有衰减，仍保持在128 mAh·g^-1。X射线衍射研究表明合成单一Li₃V₂(PO₄)₃晶体所需温度比固相法低；并考察了循环20次后材料充电到各个单相的晶体结构，通过X射线衍射和最小二乘法计算给出了其晶胞参数变化过程，证实了循环嵌Li过程中晶体结构能够得到重现。     

p-n异质结BiPO4/Ag3PO4的制备及其增强的模拟太阳光活性

采用一步水热合成法制备了BiPO₄、Ag₃PO₄和BiPO₄/Ag₃PO₄复合光催化剂,通过X射线粉末衍射（XRD）、X射线光电子能谱（XPS）、扫描电子显微镜（SEM）、紫外-可见漫反射（UV-Vis DRS）等表征手段对其组成结构、形貌及光吸收性质进行了表征,结果表明Ag₃PO₄呈块状结构,BiPO₄则分布在其表面,形成的BiPO₄/Ag₃PO₄复合光催化剂具有单斜相和立方晶相结构,带边吸收拓宽至571 nm。以甲基橙和加替沙星为目标污染物,考察了BiPO₄/Ag₃PO₄复合光催化剂在模拟太阳光照射下的降解矿化能力,结果表明复合催化剂比单一催化剂的降解矿化能力更强,稳定性更好。此外,自由基捕获实验表明空穴是该光催化过程中的主要活性物种,·O₂^-次之。p-n异质结的形成使BiPO₄/Ag₃PO₄复合光催化剂具有较强的电子空穴分离能力是光催化活性提高的主要原因,这与光电流和电化学阻抗谱测试结果相一致。基于以上结果,文中对BiPO₄/Ag₃PO₄光催化降解有机污染物的机理进行了推测。     

p-n异质结BiPO_4/Ag_3PO_4的制备及其增强的模拟太阳光活性

采用一步水热合成法制备了BiPO_4、Ag_3PO_4和BiPO_4/Ag_3PO_4复合光催化剂,通过X射线粉末衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、紫外-可见漫反射(UV-Vis DRS)等表征手段对其组成结构、形貌及光吸收性质进行了表征,结果表明Ag_3PO_4呈块状结构,BiPO_4则分布在其表面,形成的BiPO_4/Ag_3PO_4复合光催化剂具有单斜相和立方晶相结构,带边吸收拓宽至571 nm。以甲基橙和加替沙星为目标污染物,考察了BiPO_4/Ag_3PO_4复合光催化剂在模拟太阳光照射下的降解矿化能力,结果表明复合催化剂比单一催化剂的降解矿化能力更强,稳定性更好。此外,自由基捕获实验表明空穴是该光催化过程中的主要活性物种,·O2-次之。p-n异质结的形成使BiPO_4/Ag_3PO_4复合光催化剂具有较强的电子空穴分离能力是光催化活性提高的主要原因,这与光电流和电化学阻抗谱测试结果相一致。基于以上结果,文中对BiPO_4/Ag_3PO_4光催化降解有机污染物的机理进行了推测。     

Synthesis, structures and photocatalytic activities of microcrystalline ABi2Nb2O9 (A=Sr, Ba) powders

Microcrystalline ABi₂Nb₂O₉ (A=Sr, Ba) photocatalysts were successfully synthesized by a citrate complex method. The as-prepared samples were characterized by the X-ray diffraction technique, BET surface area analysis, UV-vis diffuse reflectance spectrum, transmission electron microscopy, X-ray photoelectron spectroscopy and inductively coupled plasma-atomic emission spectrometry. The results indicated that single-phase orthorhombic SrBi₂Nb₂O₉ could be obtained after being calcined above 650 °C, while BaBi₂Nb₂O₉ was tetragonal. Based on the diffuse reflectance spectra, the band gaps of the obtained samples were calculated to be around 3.34-3.54 eV. For the photocatalytic redox reaction of methyl orange under UV-light irradiation, SrBi₂Nb₂O₉ exhibited higher photocatalytic activity than that of BaBi₂Nb₂O₉. The effects of the crystallinities, BET surface areas and crystal structures of the samples on the photocatalytic activities were discussed in detail.     

钛铁矿制备二氧化钛-四氧化三铁复合材料及其光催化应用

TiO_2因具有多种优异的特性被广泛应用在半导体光催化领域,但是纳米结构的TiO_2颗粒细微,在进行光催化反应之后,难以回收再利用。本文以廉价钛铁矿为原料制备光催化剂TiO_2,同时利用副产物铁合成Fe_3O_4,并采用简单温和的浸渍法制备Fe_3O_4/TiO_2磁性复合材料。通过XRD、FT-IR、SEM、EDS等手段对材料形态结构进行表征分析,并以光降解有机污染物若丹明B为探针反应,考察其光催化性能。结果表明,质量比为1∶10的Fe_3O_4/TiO_2复合材料结构稳定、分散均匀,具有最优的光催化活性(波长356nm下反应3h,若丹明B降解率达到64.0%),并表现出良好的重复性。同时,动力学结果显示降解符合一级反应动力学。     

Bi2MoO6/BiVO4异质结的水热合成和可见光催化活性

采用一步水热法制备Bi₂MoO₆/BiVO₄复合光催化剂. 利用X 射线衍射(XRD)、场发射扫描电子显微镜(FESEM)、高分辨透射电子显微镜(HRTEM)等手段对其晶体结构和微观结构进行了表征. 结果表明, Bi₂MoO₆纳米粒子沉积在BiVO₄纳米片表面从而形成异质结结构. 紫外-可见漫反射光谱(UV-Vis DRS)表明所制备的Bi₂MoO₆/BiVO₄异质结较纯相Bi₂MoO₆和BiVO₄对可见光吸收更强. 由于形成异质结结构及其光吸收性能使Bi₂MoO₆/BiVO₄ 光催化活性有较大提高. 可见光下(λ>420 nm)光催化降解罗丹明B (RhB)实验结果表明,Bi₂MoO₆/BiVO₄光催化活性较纯相Bi₂MoO₆和BiVO₄高. Bi₂MoO₆/BiVO₄样品光催化性能提高的原因是Bi₂MoO₆和BiVO₄形成异质结, 从而有效抑制光生电子-空穴对的复合, 增大了可见光吸收范围及比表面积.     

Synthesis, characterization, and photocatalytic properties of InVO4 nanoparticles

Nanosized InVO₄ with orthorhombic structure was successfully synthesized at a relatively low calcination temperature of 600 °C by using an amorphous heteronuclear complex as precursor. The photocatalytic activity of InVO₄ catalyst has been evaluated by the decomposition of formaldehyde (FAD) under UV light () and visible light irradiation (). The as-synthesized InVO₄ catalyst showed higher photocatalytic activity for the FAD decomposition compared to the sample prepared by the conventional solid-state reaction. The calculations of the electronic band structures indicated that the valence band was composed of the O 2p orbitals, whereas the conduction band was formed by the V 3d orbitals with a small contribution of the In 5s orbitals. The photocatalytic activity of the as-prepared sample is discussed on the basis of the electronic band structure and bulk material structure.     

立方晶型Sb2O3纳米晶的合成及光催化性能

采用沉淀法合成了立方晶型Sb2O3纳米晶,通过X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)和电子自旋共振谱(ESR)等对样品进行了详细的表征。以紫外光光催化降解甲基橙为反应模型评价了样品的光催化性能。结果表明:沉淀法合成的立方晶型Sb2O3纳米晶颗粒小,表现出良好的光催化性能。对立方晶型Sb2O3纳米晶光催化降解甲基橙的原因进行了探讨,并提出了降解甲基橙的反应机理。     

SiO2/TiO2-xCx/C的制备、表征及其吸附和可见光催化性能

以SiO2为成核中心,钛酸四丁酯为钛源,分别以多羟基化合物乙二醇、丙三醇、葡萄糖和聚乙烯醇为联接剂,采用水解沉淀法制备了碳掺杂和包覆的多孔SiO2/TiO2-xCx/C可见光响应型光催化剂。采用X-射线衍射(XRD)、透射电子显微镜(TEM)、X-射线光电子能谱(XPS)、傅里叶变换-红外光谱(FTIR)、比表面积(BET)和紫外-可见(UV-Vis)漫反射光谱对样品进行表征。对不同结构样品的形成机理进行了分析。以次甲基蓝(MB)溶液为模拟废水,对样品的吸附性能和可见光催化性能进行了评价。结果表明,多羟基化合物对材料的结构和性能有重要影响。碳的掺杂和包覆使材料的吸收光谱包含了整个可见光区,而多孔结构使材料的吸附性能得到提高。以聚乙烯醇为原料所得样品吸附性能最好,30 min内吸附率达到70%;而以丙三醇为原料所得样品具有最好的可见光催化性能,40 min内次甲基蓝的降解率达到95%。     

花状结构Bi2WO6多孔微球: 组装及光催化性能

利用表面活性剂十六烷基三甲基溴化铵(CTAB)、十二烷基苯磺酸钠(SDBS)作为结构导向剂,在水热条件下合成了由纳米片组装而成的Bi2WO6花状多孔微球的新颖结构。探讨了反应时间、表面活性剂种类等因素对产物形貌、结构和性能的影响。在氙灯照射下,发现使用CTAB所得到的Bi2WO6比添加SDBS所得到的样品具有更高的催化罗丹明B降解的活性,原因是前者具有较大的比表面积和吸收阈值。同时提出了晶体可能的生长机理为各向异性生长特性和自组装-Ostwald熟化过程的结合。     

Rapid Synthesis of Nanocrystalline TiO2/SnO2 Binary Oxides and Their Photoinduced Decomposition of Methyl Orange

A rapid and simple method, the so-called stearic acid method (SAM) was developed to prepare nanostructured TiO₂/SnO₂ binary oxides by combustion of stearic acid precursors. The preparative process was studied by Fourier transform infrared spectroscopy (FT-IR). During the preparative process, metal precursors were dispersed in stearic acid at molecular level. Microstructure of the samples was investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), BET specific surface area measurement and the results were compared with those obtained by conventional sol-gel method. The photocatalytic decomposition of methyl orange was used as a model system to determine the relative influences of the preparation method and the concentration of SnO₂ on the photocatalytic activities. It was found that preparative methods affected the crystalline structure of TiO₂/SnO₂ powders and the anatase phase of TiO₂ was stabilized by the addition of SnO₂ in SAM. The samples prepared by SAM showed better dispersity, larger specific surface area and the TiO₂/SnO₂ (r=0.15, SAM) catalyst showed higher photocatalytic activity than Degussa P25.