Characteristic turbulent structure of a modified drag-reduced surfactant solution flow via dosing water from channel wall

The modification of the near-wall structure is very important for the control of wall turbulence. To ascertain the effect of near-wall modulation on the viscoelastic drag-reduced flow, the modified characteristics of a surfactant solution channel flow were investigated experimentally. The modulation was conducted on the boundary of the channel flow by injecting water from the whole surface of one side of the channel wall. The diffusion process of the injected water was observed by using the planar laser-induced fluorescence technique. The velocity statistics and characteristic structure including the spatial distributions of instantaneous streamwise velocity, swirling strength, and Reynolds shear stress were analyzed based on the velocity vectors acquired in the streamwise wall-normal plane by using the particle imaging velocimetry technique. The results indicated that the disturbance of the injected water was constricted within a finite range very near the dosing wall, and the Reynolds shear stress was increased in this region. However, the eventual drag reduction rate was found to be increased due to a relatively large decrement of viscoelastic shear stress in this near-wall region. Moreover, the flow structure under this modulation presented obvious regional characteristics. In the unstable disturbed region, the mixing of high-speed and low-speed fluids and the motions of ejection and sweep occurred actively. Many clockwise vortex cores were also found to be generated. This characteristic structure was similar to that in the ordinary turbulence of Newtonian fluid. Nevertheless, outside this disturbed region, the structure still maintained the characteristics of the drag-reduced flow with non-Newtonian viscoelastic additives. These results proved that the injected Newtonian fluid associated with the modified stress distribution creates a diverse characteristic structure and subsequent enhanced drag reduction. This investigation can provide the experimental basis for further study of turbulence control.     

An investigation of possible mechanisms of heterogeneous drag reduction in pipe and channel flows

When concentrated polymer solutions are injected into the core-region of a turbulent pipe or channel flow, the injected polymer solution forms a thread which preserves its identity far beyond the injection point. The resulting drag reduction is called heterogeneous drag reduction.This study presents experimental results on the mechanism of this type of drag reduction. The experiments were carried out to find out whether this drag reduction is caused by small amounts of polymer removed from the thread and dissolved in the near-wall region of the flow or by an interaction of the polymer thread with the turbulence. The friction behavior of this type of drag reduction was measured for different concentrations in pipes of different cross-sections, but of identical hydraulic diameter. The parameters of the injection, i.e. injector geometry as well as the ratio of the injection to the bulk velocity, were varied. In one set of experiments the polymer thread was sucked out through an orifice and the friction behavior in the pipe was determined downstream of the orifice. In another experiment, near-wall fluid was led into a bypass in order to measure its drag reducing properties. Furthermore, the influence of a water injection into the near-wall region on the drag reduction was studied.The results provide a strong evidence that heterogeneous drag reduction is in part caused by small amount of dissolved polymer in the near-wall region as well as by an interaction of the polymer thread with the turbulence.Nomenclature a channel height - b channel width - c _p concentration of the injected polymer solution - c _R effective polymer concentration averaged over the cross-section - d pipe or hydraulic diameter - d _i injector diameter - DR drag reduction - f friction factor - l downstream distance from injector - L length of a pipe segment - P polymer type - p differential pressure - Re Reynolds number - U bulk velocity - u ^* ratio of injection to bulk velocity - y ⁺ dimensionless wall distance - v kinematic viscosity - density of the fluid - _w wall shear stress     

Modeling of drag reduction in turbulent channel flow with hydrophobic walls by FVM method and weakly-compressible flow equations

In this paper the effects of hydrophobic wall on skin-friction drag in the channel flow are investigated through large eddy simulation on the basis of weaklycompressible flow equations with the MacCormack's scheme on collocated mesh in the FVM framework. The slip length model is adopted to describe the behavior of the slip velocities in the streamwise and spanwise directions at the interface between the hydrophobic wall and turbulent channel flow. Simulation results are presented by analyzing flow behaviors over hydrophobic wall with the Smagorinky subgrid-scale model and a dynamic model on computational meshes of different resolutions. Comparison and analysis are made on the distributions of timeaveraged velocity, velocity fluctuations, Reynolds stress as well as the skin-friction drag. Excellent agreement between the present study and previous results demonstrates the accuracy of the simple classical second-order scheme in representing turbulent vertox near hydrophobic wall. In addition, the relation of drag reduction efficiency versus time-averaged slip velocity is established. It is also foundthat the decrease of velocity gradient in the close wall region is responsible for the drag reduction. Considering its advantages of high calculation precision and efficiency, the present method has good prospect in its application to practical projects.     

The influence of flow-induced non-Newtonian fluid properties on turbulent drag reduction

Friction factors and velocity profiles in turbulent drag reduction can be compared to Newtonian fluid turbulence when the shear viscosity at the wall shear rate is used for the Reynolds number and the local shear viscosity is used for the non-dimensional wall distance. On this basis, an apparent maximum drag reduction asymptote is found which is independent of Reynolds number and type of drag reducing additive. However, no shear viscosity is able to account for the difference between the measured Reynolds stress and the Reynolds stress calculated from the mean velocity profile (the Reynolds stress deficit). If the appropriate local viscosity to use with the velocity fluctuation correlations includes an elongational component, the problem can be resolved. Taking the maximum drag reduction asymptote as a non-Newtonian flow, with this effective viscosity, leads to agreement with the concept of an asymptote only when the solvent viscosity is used in the non-dimensional wall distance.     

Laminar,transitional and turbulent annular flow of drag-reducing polymer solutions

Mean and rms axial velocity-profile data obtained using laser Doppler anemometry are presented together with pressure-drop data for the flow through a concentric annulus (radius ratio κ = 0.506) of a Newtonian (a glycerine–water mixture) and non-Newtonian fluids—a semi-rigid shear-thinning polymer (a xanthan gum) and a polymer known to exhibit a yield stress (carbopol). A wider range of Reynolds numbers for the transitional flow regime is observed for the more shear-thinning fluids. In marked contrast to the Newtonian fluid, the higher shear stress on the inner wall compared to the outer wall does not lead to earlier transition for the non-Newtonian fluids where more turbulent activity is observed in the outer wall region. The mean axial velocity profiles show a slight shift (～5%) of the location of the maximum velocity towards the outer pipe wall within the transitional regime only for the Newtonian fluid.     

Flow around a sphere with material cross flow at low reynolds numbers

An analytical solution is carried out for the problem of the flow around a sphere with material cross flow at Reynolds numbers less than 1 and a blowing velocity less than the free stream velocity. The method of asymptotic expansions of Pearson and Proudman is used for the solution. Expressions are obtained for the distribution of the current and velocity component functions as well as for the aerodynamic drag coefficient of the sphere. It is shown that blowing diminishes the sphere drag, where its influence will increase as the Reynolds number grows.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 3, pp. 103–109, May–June, 1972.     

Influence of wavy structured surfaces and large scale polymer structures on drag reduction

Drag reduction was studied for turbulent flow over a structured wall that contained 600 sinusoidal waves with a wavelength of 5 mm and an amplitude of 0.25 mm. A concentrated solution of a co-polymer of polyacrylamide and sodium acrylate was injected into the flow through wall slots. Laser Doppler velocimetry was used to measure turbulence. A fluorescence technique was developed that enabled us to demonstrate the existence, under certain circumstances, of large gelatinous structures in the injected polymer solution and in the flow channel.At maximum drag reduction, the Reynolds shear stress was zero and the velocity field was the same as found for a smooth surface. Larger drag reductions could be realized for a wavy wall because the initial drag was larger. The influences of polymers on the turbulent fields are similar for smooth and wavy boundaries. These results are of interest since the interaction with the wall can be quite different for water flow over smooth and wavy boundaries (which are characterized as being completely rough). An important effect of polymers is a decreasing relative importance of high frequency fluctuations with increasing drag reduction that is characterized by a cut-off frequency. This cut-off is the same for smooth and wavy walls at maximum drag reduction. The sensitivity of drag reduction to the method of preparing and delivering the polymer solution suggests that aggregation of polymers could be playing an important role for the system that was studied. For example, drag reduction was enhanced when large polymer structures are present.     

Evaluation of flush mounted hot-film sensors for skin friction reduction measurements in viscoelastic polymer solutions

The purpose of this investigation was to evaluate the performance of flush mounted hot-film sensors for mean wall shear stress measurement in turbulent flows of dilute drag reducing polymer solution. A series of pipe flow expriments were conducted over a range of Reynolds numbers and polymer solution concentrations to compare the level of skin friction drag reduction measured by hot-film sensors with values calculated from pipe pressure drop. It is shown that water calibrated hot-film sensors consistently underestimate the wall shear stress suggesting that Reynolds analogy is not valid in dilute polymer solutions. The Newtonian form of the relationship between the wall shear stress and the heat transfer remains valid in dilute polymer solutions. However, multiplicative and additive factors in the relationship are shown to increase linearly with the logarithm of the polymer concentration.     

A study on coherent structures and drag-reduction in the wall turbulence with polymer additives by TRPIV

An experimental measurement was performed using time-resolved particle image velocimetry (TRPIV) to investigate the spatial topological character of coherent structures in wall-bounded turbulence of polymer additive solution. The fully developed near-wall turbulent flow fields with and without polymer additives at the same Reynolds number were measured by TRPIV in a water channel. The comparisons of turbulent statistics confirm that due to viscoelastic structure of long-chain polymers, the wall-normal velocity fluctuation and Reynolds shear stress in the near-wall region are suppressed significantly. Furthermore, it is noted that such a behavior of polymers is closely related to the decease of the motion of the second and forth quadrants, i.e., the ejection and sweep events, in the near-wall region. The spatial topological mode of coherent structures during bursts has been extracted by the new mu-level criteria based on locally averaged velocity structure function. Although the general shapes of coherent structures are unchanged by polymer additives, the fluctuating velocity, velocity gradient, velocity strain rate and vorticity of coherent structures during burst events are suppressed in the polymer additive solution compared with that in water. The results show that due to the polymer additives the occurrence and intensity of coherent structures are suppressed, leading to drag reduction.     

倾斜吹吸控制下湍流边界层减阻的直接数值模拟

雷诺切应力是壁湍流高摩擦阻力的重要来源, 有理论认为可以通过壁面生成负雷诺应力(数值上为正)的方式来削弱湍流流场中雷诺应力的分布, 以此获得流动减阻. 而通过对雷诺平均运动方程的法向二次积分, 可以发现壁面生成正雷诺应力(数值上为负)对壁面摩擦阻力系数才有负贡献. 文中在湍流边界层流动的控制区域下边界设置一系列倾斜狭缝, 利用该装置通过周期性吹吸的方法产生壁面生成正(负)雷诺应力, 并采用直接数值模拟方法考察和验证上文提到的减阻理论. 文中采用的湍流边界层流动模型, 其流动雷诺数(基于外流速度及动量损失厚度)从300 发展到860. 文中通过多组数值模拟算例, 考察了射流强度和频率对壁面摩擦阻力系数的影响, 并对比了壁面生成正或负雷诺应力对流动的影响. 研究表明, 壁面生成正雷诺应力控制的减阻率能达到3.26, 而壁面生成负雷诺应力控制的减阻效果较壁面生成正雷诺应力控制的要差; 壁面生成的正雷诺应力对壁面摩擦阻力有负贡献, 而壁面生成的负雷诺应力对壁面摩擦阻力有正贡献; 通过考察控制的收支比, 发现控制方案不能获得能量净收益.      

Turbulent Drag Reduction by Uniform Blowing Over a Two-dimensional Roughness

Direct numerical simulation (DNS) of turbulent channel flow over a two-dimensional irregular rough wall with uniform blowing (UB) was performed. The main objective is to investigate the drag reduction effectiveness of UB on a rough-wall turbulent boundary layer toward its practical application. The DNS was performed under a constant flow rate at the bulk Reynolds number values of 5600 and 14000, which correspond to the friction Reynolds numbers of about 180 and 400 in the smooth-wall case, respectively. Based upon the decomposition of drag into the friction and pressure contributions, the present flow is considered to belong to the transitionally-rough regime. Unlike recent experimental results, it turns out that the drag reduction effect of UB on the present two-dimensional rough wall is similar to that for a smooth wall. The friction drag is reduced similarly to the smooth-wall case by the displacement of the mean velocity profile. Besides, the pressure drag, which does not exist in the smooth-wall case, is also reduced; namely, UB makes the rough wall aerodynamically smoother. Examination of turbulence statistics suggests that the effects of roughness and UB are relatively independent to each other in the outer layer, which suggests that Stevenson’s formula can be modified so as to account for the roughness effect by simply adding the roughness function term.     

Turbulent characteristics of shear-thinning fluids in recirculating flows

 A miniaturised fibre optic Laser-Doppler anemometer was used to carry out a detailed hydrodynamic investigation of the flow downstream of a sudden expansion with 0.1–0.2% by weight shear-thinning aqueous solutions of xanthan gum. Upstream of the sudden expansion the pipe flow was fully-developed and the xanthan gum solutions exhibited drag reduction with corresponding lower radial and tangential normal Reynolds stresses, but higher axial Reynolds stress near the wall and a flatter axial mean velocity profile in comparison with Newtonian flow. The recirculation bubble length was reduced by more than 20% relative to the high Reynolds number Newtonian flow, and this was attributed to the occurrence further upstream of high turbulence for the non-Newtonian solutions, because of advection of turbulence and earlier high turbulence production in the shear layer. Comparisons with the measurements of Escudier and Smith (1999) with similar fluids emphasized the dominating role of inlet turbulence. The present downstream turbulence field was less anisotropic, and had lower maximum axial Reynolds stresses (by 16%) but higher radial turbulence (20%) than theirs. They reported considerably longer recirculating bubble lengths than we do for similar non-Newtonian fluids and Reynolds numbers. Received: 23 February 1999/Accepted: 28 April 1999     

The effect of mixed convection on the structure of channel flow at low Reynolds numbers

An experimental study was conducted to investigate the effect of bottom wall heating on the flow structure inside a horizontal square channel at low Reynolds numbers (Re) and high Grashof numbers (Gr). The flow field was found to be complex and three-dimensional due to the interactions of buoyancy-induced rising plumes of warm fluid, falling parcels of cold fluid and the shear flow. The mean streamwise velocity profiles were altered by bottom wall heating; and back flow was induced in the upper half of the channel when Gr/Re² > 55. The bottom wall temperatures were found to have more significant influence on the turbulent velocity magnitudes than the flow rate. The Reynolds stress became negative in the channel core region indicating the momentum transfer from the turbulent velocity field to the buoyancy field. The POD analysis revealed the presence of convective cells primarily in the lower half of the channel.     

Velocity and conformation statistics based on reduced Karhunen–Loeve projection data from DNS of viscoelastic turbulent channel flow

To investigate the effectiveness of the Karhunen–Loeve (K–L) method as a data reduction approach, we study here its effect on the velocity and conformation statistics in a drag reducing turbulent polymer flow. The K–L method has been used to construct a set of basis velocity eigenfunctions from a large number of independent realizations of the velocity. Those were obtained from direct numerical simulation (DNS) of a viscoelastic turbulent channel flow using the Giesekus model. A subset of the K–L eigenfunctions, large enough to contain more than 90% of the fluctuating kinetic energy of the flow on the average, has then been subsequently used to obtain time series of projection coefficients of the velocity fields generated further from DNS. In a post-processing step, velocity fields were reconstructed using selected subsets of the projection coefficients. Those reconstructed velocity fields were then used to evaluate turbulent statistics as well as to integrate the constitutive equation. The turbulent statistics (r.m.s. velocities, Reynolds stress etc.) thus constructed showed good agreement with the full results from DNS. The Reynolds stress anisotropy was also calculated in this work for the first time. It was found to increase with viscoelasticity that was well reproduced in the reduced K–L data except near the channel centerline where the K–L data showed some loss of anisotropy. The biggest differences however between the K–L reduced data and the full DNS results were seen in the conformation statistics. The average polymer conformation extracted from the K–L reduced data was significantly less than that corresponding to the full DNS results anywhere except in the shear-dominated wall region. A further comparison of the energy and dissipation spectra between the full DNS and the K–L reconstructed data illustrated the impact of the K–L process in resulting to a significant damping of small turbulent scales even those contributing to the maximum in turbulent dissipation. This may also be the principal reason behind the poor quality of the K–L reconstructed conformation data.     

Turbulent Couette–Poiseuille flow with zero wall shear

A particular pressure-driven flow in a plane channel is considered, in which one of the walls moves with a constant speed that makes the mean shear rate and the friction at the moving wall vanish. The Reynolds number considered based on the friction velocity at the stationary wall (u_τ,S) and half the channel height (h) is Re_τ,S = 180. The resulting mean velocity increases monotonically from the stationary to the moving wall and exhibits a substantial logarithmic region. Conventional near-wall streaks are observed only near the stationary wall, whereas the turbulence in the vicinity of the shear-free moving wall is qualitatively different from typical near-wall turbulence. Large-scale-structures (LSS) dominate in the center region and their spanwise spacing increases almost linearly from about 2.3 to 4.2 channel half-heights at this Re_τ,S. The presence of LSS adds to the transport of turbulent kinetic energy from the core region towards the moving wall where the energy production is negligible. Energy is supplied to this particular flow only by the driving pressure gradient and the wall motion enhances this energy input from the mean flow. About half of the supplied mechanical energy is directly lost by viscous dissipation whereas the other half is first converted from mean-flow energy to turbulent kinetic energy and thereafter dissipated.     

Turbulence production in flow over a wavy wall

Measurements of the spatial and time variation of two components of the velocity have been made over a sinusoidal solid wavy boundary with a height to length ratio of 2a/λ = 0.10 and with a dimensionless wave number of α⁺ = (2π/λ)(v/u ^?) = 0.02. For these conditions, both intermittent and time-mean flow reversals are observed near the troughs of the waves. Statistical quantities that are determined are the mean streamwise and normal velocities, the root-meansquare of the fluctuations of the streamwise and normal velocities, and the Reynolds shear stresses. Turbulence production is calculated from these measurements. The flow is characterized by an outer flow and by an inner flow extending to a distance of about α^?1 from the mean level of the surface. Turbulence production in the inner region is fundamentally different from flow over a flat surface in that it is mainly associated with a shear layer that separates from the back of the wave. Flow close to the surface is best described by an interaction between the shear layer and the wall, which produces a retarded zone and a boundary-layer with large wall shear stresses. Measurements of the outer flow compare favorably with measurements over a flat wall if velocities are made dimensionless by a friction velocity defined with a shear stress obtained by extrapolating measurements of the Reynolds stress to the mean levels of the surface (rather than from the drag on the wall).     

固体颗粒对沟槽湍流边界层影响的实验研究

本文采用粒子图像测速技术(particles image velocimetry, PIV)研究固体颗粒对放置在平板湍流边界层中的平壁和沟槽壁面减阻效果的影响. 实验对清水和加入粒径为155 μm聚苯乙烯颗粒的流法向二维速度场信息进行采集, 对不同工况下的平均速度剖面、雷诺应力和湍流度等统计量进行对比, 分析流体在边界层中的行为. 运用空间局部平均结构函数提取了不同工况湍流边界层喷射?扫掠行为的空间拓扑结构并进行比较. 结果发现, 在不同的壁面条件下, 粒子加入后的对数律区中无量纲速度均略大于清水组, 雷诺切应力有所降低, 湍流度有所减弱. 对于不同流场速度下的沟槽而言, 颗粒的加入均降低了壁面附近的阻力, 而颗粒单独作用于光滑壁面的减阻效果并不明显. 加入粒子后的相干结构数目有所增加, 法向脉动速度下降. 沟槽壁面附近的相干结构数目有所增加, 法向脉动速度在自由来流速度较大时有所上升, 在速度较小时有所下降. 这表明不同减阻状况下的沟槽均能将大涡破碎成更多的涡, 并且粒子的加入强化了这种破碎作用.      

Influence of blowing on the anisotropy of the Reynolds stress tensor in a turbulent channel flow

The effects of localized wall blowing through a porous strip are investigated using hot-wire anemometry in a turbulent channel flow. Three blowing magnitudes are studied: σ=0.22, 0.36 and 0.58, where σ is the momentum flux gain ratio and that of the incoming channel flow at three different positions from the spanwise porous strip. The main emphasis of this work was the departure from isotropy of the turbulent flow with localized blowing. The anisotropic invariant map (AIM) for the Reynolds stress tensor revealed that blowing decreased the anisotropy of the turbulent structure in the near-wall region, and a decrease in the longitudinal integral length scale was observed when the blowing rate increased.     

Temporal and spatial transients in turbulent boundary layer flow over an oscillating wall

Direct numerical simulations have been performed to study the effect of an oscillating segment of the wall on a turbulent boundary layer flow. Two different oscillation amplitudes with equal oscillation period have been used, which allows a direct comparison between a relatively weak and strong forcing of the flow. The weaker forcing results in 18% drag reduction while the stronger forcing, with twice the amplitude, yields 29% drag reduction. The downstream development of the drag reduction is compared with earlier simulations and experiments. In addition, a simulation with identical oscillation parameters as in previous numerical and experimental investigations allows for an estimation of the effect of the Reynolds number on the drag reduction.Reductions in the Reynolds stresses and the important role that the edge of the Stokes layer has is explained.An estimation of the idealized power consumption shows that a positive energy budget is only possible for the weaker wall velocity case.Spatial and temporal transients are investigated and a transformation between spatial and temporal coordinates via a convection velocity is shown to facilitate a comparison between the two transients in a consistent manner. The streamwise shear exhibits a similar monotonic behavior in the spatial and temporal transients, while the non-monotinic temporal transient of the longitudinal Reynolds stress has no counterpart in the spatial development. Furthermore, the evolution in time of the spanwise Reynolds stress is very similar to previously reported channel flow data.The instantaneous spanwise velocity profile (only averaged in the homogeneous spanwise direction) will for the first time be presented from a boundary layer over an oscillating wall, and comparisons with the analytical solution to the laminar Navier–Stokes equations show very good agreement.     

The effect of a systematic change in surface roughness skewness on turbulence and drag

Previous work by the authors (Flack and Schultz, 2010) has identified the root-mean-square roughness height, k_rms, and the skewness, Sk, of the surface elevation distribution as important parameters in scaling the skin-friction drag on rough surfaces. In this study, three surfaces are tested in turbulent boundary layer flow at a friction Reynolds number, Re_τ = 1600–2200. All the surfaces have similar root-mean-square roughness height, while the skewness is varied. Measurements are presented using both two-component LDV and PIV. The results show the anticipated trend of increasing skin-friction drag with increasing skewness. The largest increase in drag occurs going from negative skewness to zero skewness with a more modest increase going from zero to positive skewness. Some differences in the mean velocity and Reynolds stress profiles are observed for the three surfaces. However, these differences are confined to a region close to the rough surface, and the mean velocity and Reynolds stress profiles collapse away from the wall when scaled in outer variables. The turbulence structure as documented through two-point spatial correlations of velocity is also observed to be very similar over the three surfaces. These results support Townsend’s (1976) concept of outer-layer similarity that the wall boundary condition exerts no direct influence on the turbulence structure away from the wall except in setting the velocity and length scales for the outer layer.