Physicochemical Characteristics of Polypyrrole/(Glucose oxidase)/(Prussian Blue)‐based Biosensor Modified with Ni‐ and Co‐Hexacyanoferrates

In this work, three types of electrodes suitable for amperometric glucose biosensors were designed. One type of electrode was based on bio‐selective layer of polypyrrole/(glucose oxidase)/(Prussian Blue) (Ppy/GOx/PB) and it was used as a control electrode regarding to which electrochemical properties of two other types of electrodes were compared. During the formation of Prussian blue layers graphite electrodes were additionally modified by Ni‐hexacyanoferrate (NiHCF) and by Co‐hexacyanoferrate (CoHCF) in order to design Ppy/GOx/PB‐NiHCF and Ppy/GOx/PB‐CoHCF electrodes, respectively. Some physicochemical characteristics of all three types of electrodes were evaluated and compared. The Ppy/GOx/PB‐NiHCF electrode showed wider linear range of the calibration curve than Ppy/GOx/PB and Ppy/GOx/PB‐CoHCF electrodes. The effect of temperature on analytical performance of the Ppy/GOx/PB‐NiHCF based biosensor has been evaluated and activation energy of enzyme catalysed reaction has been calculated within the temperature range of 15 °C to 30 °C.     

Glucose sensor based on redox-cycling between selectively modified and unmodified combs of carbon interdigitated array nanoelectrodes

We present a novel electrochemical glucose sensor employing an interdigitated array (IDA) of 1:1 aspect ratio carbon nanoelectrodes for the electrochemical-enzymatic redox cycling of redox species (ferricyanide/ferrocyanide) between glucose oxidase (GOx) and the two comb-shaped nanoelectrodes of the IDA. The carbon nanoelectrodes were fabricated using a simple, cost-effective, reproducible microfabrication technology known as the carbon-microelectromechanical-systems (C-MEMS) process. One comb (comb 1) of the IDA was selectively modified with GOx via the electrochemical reduction of an aryl diazonium salt, while the other comb (comb 2) remained unmodified; this facilitates electrochemically more active surface of comb 2, resulting in sensitive glucose detection. Ferricyanide is reduced to ferrocyanide by the GOx in the presence of glucose, and ferrocyanide diffuses to both combs of the IDA where it is oxidized. The limited electrochemical current collection at the surface-modified comb 1 is counterbalanced by the efficient redox cycling between the enzyme sites at comb 1 and the bare carbon surface of comb 2. Reducing the electrode-to-electrode gap between the two combs (gap = 1.9 μm) increases the diffusion flux of redox species at comb 2 hence, enhanced the sensitivity and limit of detection of the glucose sensor by ∼2.3 and ∼295 times, respectively at comb 2 compared to comb 1. The developed IDA-based glucose sensor demonstrated good amperometric response to glucose, affording two linear ranges from 0.001 to 1 mM and from 1 to 10 mM, with limits of detection of 0.4 and 61 μM and sensitivities of 823.2 and 70.0 μA mM⁻¹ cm⁻², respectively.     

LSI-based amperometric sensor for bio-imaging and multi-point biosensing

We have developed an LSI-based amperometric sensor called "Bio-LSI" with 400 measurement points as a platform for electrochemical bio-imaging and multi-point biosensing. The system is comprised of a 10.4 mm × 10.4 mm CMOS sensor chip with 20 × 20 unit cells, an external circuit box, a control unit for data acquisition, and a DC power box. Each unit cell of the chip contains an operational amplifier with a switched-capacitor type I-V converter for in-pixel signal amplification. We successfully realized a wide dynamic range from ±1 pA to ±100 nA with a well-organized circuit design and operating software. In particular, in-pixel signal amplification and an original program to control the signal read-out contribute to the lower detection limit and wide detection range of Bio-LSI. The spacial resolution is 250 μm and the temporal resolution is 18-125 ms/400 points, which depends on the desired current detection range. The coefficient of variance of the current for 400 points is within 5%. We also demonstrated the real-time imaging of a biological molecule using Bio-LSI. The LSI coated with an Os-HRP film was successfully applied to the monitoring of the changes of hydrogen peroxide concentration in a flow. The Os-HRP-coated LSI was spotted with glucose oxidase and used for bioelectrochemical imaging of the glucose oxidase (GOx)-catalyzed oxidation of glucose. Bio-LSI is a promising platform for a wide range of analytical fields, including diagnostics, environmental measurements and basic biochemistry.     

Carbon Cavity Microelectrode for Electrical Wiring of Enzyme by Insoluble Electroactive Species in Aqueous Media

The carbon cavity microelectrode (CME), exhibiting a volume of 4×10^?6 cm³, offers a genuine alternative for immobilizing and connecting enzymes in aqueous electrolytes by powder of insoluble redox materials. In the present work, the electrochemical behavior of two redox species such as ferrocene (Fc) and tetrathiafulvalene (TTF) was investigated with CME to evaluate their potentialities in the electrical wiring of enzymes. For this purpose, powder of two enzymes, glucose oxidase (GOx) and horseradish peroxidase (HRP), was independently mixed with an insoluble redox material and forced to fill the single micro cavity of a carbon electrode covered by an inert insulator. The presence of the electroactive species, as well as the enzyme wiring was investigated by cyclic voltammetry. The amperometric detection of glucose was carried out by potentiostating the TTF/GOx and the Fc/GOx microelectrodes at 0.25 and 0.35 V respectively. The amperometric detection of H₂O₂ by the TTF/HRP microelectrode was performed at ?0.1 V vs. SCE.     

Incorporation of glucose oxidase into Langmuir-Blodgett films based on Prussian blue applied to amperometric glucose biosensor

Glucose oxidase (GOx) was immobilized in the organic-inorganic Langmuir-Bldogett (LB) films consisting of octadecyltrimethylammonium (ODTA) and nanosized Prussian blue (PB) clusters. The amperometric glucose biosensors based on the LB films were fabricated and tested. It was found that the sensors exhibited a clear response current under an applied voltage of 0.0 V (vs Ag/AgCl). The linearity of current density versus glucose concentration was confirmed below 15 mmol/L concentration. This is the first observation of biosensor function of the hybrid organic-inorganic LB films. The successful preparation of glucose sensors operating at the very low potential indicates that the adsorbed PB clusters in the LB films act as an electrocatalyst for the electrochemical reduction of hydrogen peroxide, which is the final product of the enzymatic reaction sequence. The observed low potential applicability is estimated to inhibit the responses of interferants such as ascorbic acid, uric acid, and acetominophen. It was also found that an electrostatic interaction between positively charged ODTA+ and the adsorbed species of both GOx and PB provided a stabilized adsorption state in the LB films. Such stable immobilization contributes to the steady amperometric response current observed in the present ODTA/PB/GOx LB films.     

Amperometric glucose biosensor based on electrodeposition of platinum nanoparticles onto covalently immobilized carbon nanotube electrode

A new amperometric biosensor for glucose was developed based on adsorption of glucose oxidase (GOx) at the gold and platinum nanoparticles-modified carbon nanotube (CNT) electrode. CNTs were covalently immobilized on gold electrode via carbodiimide chemistry by forming amide linkages between carboxylic acid groups on the CNTs and amine residues of cysteamine self-assembled monolayer (SAM). The fabricated GOx/Au_nano/Pt_nano/CNT electrode was covered with a thin layer of Nafion to avoid the loss of GOx in determination and to improve the anti-interferent ability. The immobilization of CNTs on the gold electrode was characterized by quartz crystal microbalance technique. The morphologies of the CNT/gold and Pt_nano/CNT/gold electrodes have been investigated by scanning electron microscopy (SEM), and the electrochemical performance of the gold, CNT/gold, Pt_nano/gold and Pt_nano/CNT/gold electrodes has also been studied by amperometric method. In addition, effects of electrodeposition time of Pt nanoparticles, pH value, applied potential and electroactive interferents on the amperometric response of the sensor were discussed.

The enzyme electrode exhibited excellent electrocatalytic activity and rapid response for glucose in the absence of a mediator. The linear range was from 0.5 to 17.5 mM with correction coefficient of 0.996. The biosensor had good reproducibility and stability for the determination of glucose.     

Pt nanoparticles modified Au nanowire array for amperometric and potentiometric detection of glucose

A new glucose biosensor, based on the modification of highly ordered Au nanowire arrays (ANs) with Pt nanoparticles (PtNPs) and subsequent surface adsorption of glucose oxidase (GOx), is described. Morphologies of ANs and ANs/PtNPs were observed by scanning electron microscope. The electrochemical properties of ANs, ANs/GOx, ANs/PtNPs, and ANs/PtNPs/GOx electrodes were compared by cyclic voltammetry. Results obtained from comparison of the cyclic voltammograms show that PtNPs modification enhances electrochemical catalytic activity of ANs to H₂O₂. Hence, ANs/PtNPs/GOx biosensor exhibits much better sensing to glucose than ANs/GOx. Optimum deposition time of ANs/PtNPs/GOx biosensor for both amperometric and potentiometric detection of glucose was achieved to be 150 s at deposition current of 1?×?10^?6 A. A sensitivity of 0.365 μA/mM with a linear range from 0.1 to 7 mM was achieved for amperometric detection; while for potentiometric detection the sensitivity is 33.4 mV/decade with a linear range from 0.1 to 7 mM.     

New Carbosilane Polymers with Interacting Ferrocenes as Support and Bioelectrocatalysts of Oxidases to Develop Versatile and Specific Amperometric Biodevices

In this work, the bioelectrocatalytical properties and kinetic characteristics of new oxidase amperometric biosensors based on two different ferrocene functionalized carbosilane polymers, polydiallylmethylsilane (PDAMS) and polymethyldiundecenylsilane (PMDUS) are described. In the development of these biodevices, glucose oxidase has been used as example of oxidase enzyme, and two different immobilization procedures have been studied. The polymer-modified electrodes act as efficient transducers for glucose sensing in anodic and cathodic aerobic conditions and also in anodic anaerobic conditions, and this fact turns them into useful devices for a wide field of applications. PMDUS has shown to be the bioelectrocatalyst with best kinetic and analytical properties in aerobic media while PDAMS was better in anaerobic conditions. The best aerobic biosensor developed displayed a strictly linear range from 0 to 3.0?mM, a detection limit of 7.8???M and a response time less than 2?s in an ascorbate interference free work potential interval. The apparent Michaelis?CMenten constant was calculated to be 1.36?mM according to the Lineweaver?CBurk equation.     

Application of polypyrrole/GOx film to glucose biosensor based on electrochemical-surface plasmon resonance technique

A surface plasmon resonance (SPR) based biosensor for glucose is presented in which a thin gold film modified with polypyrrole and glucose oxidase (PPy-GOx) acts as the sensor chip. It is based on SPR response to the change of refractive index of PPy-GOx film by the enzymatic catalytic reaction. The co-electropolymerization of pyrrole and GOx was carried out under cyclic voltammetric conditions, and simultaneously monitored by in-situ SPR. It has been revealed that the enzymatic reaction between GOx and PPy in the presence of glucose can lead to distinct changes in the SPR signal. From the experiments, a linear relationship was obtained in the range 1–100 μmol L^?1 between glucose concentration and the rate of redox transformation of PPy. The detection limit was 0.5 μmol L^?1 (S/N?=?3) and recoveries were 95.2–102.7%.     

Reduced Graphene Oxide/Pt Nanoparticles/Zn‐MOF‐74 Nanomaterial for a Glucose Biosensor Construction

In this study, a new glucose biosensor was fabricated by immobilizing glucose oxidase (GOx) on platinum nanoparticles (Pt NPs) decorated reduced graphene oxide (rGO)/Zn‐MOF‐74 hybrid nanomaterial. Herein, the biosensor fused the advantages of rGO with those of porous Zn‐MOF and conductive Pt NPs. This has not only enlarged the surface area and porosity for the efficient GOx immobilization and faster mass transport, but also provided favorable electrochemical features such as high current density, remarkable electron mobility through metal nanoparticles, and improved electron transfer between the components. The GOx‐rGO/Pt NPs@Zn‐MOF‐74 coated electrode displayed a linear measurement range for glucose from 0.006 to 6 mM, with a detection limit of 1.8 μM (S/N: 3) and sensitivity of 64.51 μA mM^?1 cm^?2. The amperometric response of the enzyme biosensor demonstrated the typical behavior of Michaelis‐Menten kinetics. The obtained satisfying sensitivity and measurement range enabled fast and accurate glucose measurement in cherry juice using the fabricated biosensor. The water‐stable Zn‐MOF‐74 demonstrated higher enzyme loading capacity and can be potent supporting material for biosensor construction.     

Glucose biosensor based on graphite electrodes modified with glucose oxidase and colloidal gold nanoparticles

The electrochemistry of glucose oxidase (GOx) immobilized on a graphite rod electrode modified by gold nanoparticles (Au-NPs) was studied. Two types of amperometric glucose sensors based on GOx immobilized and Au-NPs modified working electrode (Au-NPs/GOx/graphite and GOx/Au-NPs/graphite) were designed and tested in the presence and the absence of N-methylphenazonium methyl sulphate in different buffers. Results were compared to those obtained with similar electrodes not containing Au-NPs (GOx/graphite). This study shows that the application of Au-NPs increases the rate of mediated electron transfer. Major analytical characteristics of the amperometric biosensor based on GOx and 13 nm diameter Au-NPs were determined. The analytical signal was linearly related to glucose concentration in the range from 0.1 to 10 mmol L^?1. The detection limit for glucose was found within 0.1 mmol L^?1 and 0.08 mmol L^?1 and the relative standard deviation in the range of 0.1–100 mol L^?1 was 0.04–0.39%. The τ_1/2 of V _max characterizes the storage stability of sensors: this parameter for the developed GOx/graphite electrode was 49.3 days and for GOx/Au-NPs/graphite electrode was 19.5 days. The sensor might be suitable for determination of glucose in beverages and/or in food.     

Chemical polymerization of m-phenylenediamine, in the presence of glucose oxidase, produces an enzyme-retaining electrooxidisable polymer used to produce a biosensor for amperometric detection of glucose from brain dialysate

A new procedure involving chemical polymerization of a monomer of m-phenylenediamine (m-ppd) containing glucose oxidase (GOx) and subsequent electro-synthesis of the functional GOx containing polymer onto platinum needle electrodes (PTNE) was used for the amperometric analysis of glucose concentration in brain dialysates. Monomer solutions of o-phenylenediamine (o-ppd) and m-ppd were polymerized by low concentrations of glutaraldehyde (GA) and precipitated from solution. The 1,3 position of the amines on the benzene was amenable to stable polymerization by GA but polymerization of o-ppd (1,2 position) by GA was unstable and degraded. Polymerization of m-ppd appears to proceed by dehydration synthesis. GA induced polymerization of m-ppd polymer in the presence of GOx produced a polymer with strongly bound, functional GOx. This GOx-m-ppd polymer formed a stable matrix that was effectively employed in flow injection analysis (FIA) of glucose. If maintained under O(2) free atmosphere after chemical polymerization, the GOx-m-ppd polymer retained the ability to be electropolymerized. PTNE coated with GOx-m-ppd polymer by repeated dip/amperometry produced stable, sensitive amperometric glucose sensors with good interference exclusion properties and long shelf life. Scanning EM demonstrated that amperometry modified the structure of the GOx-m-ppd on the PTNE surface. GOx-m-ppd PTNE glucose sensors and bare PTNE were placed in a radial flow cell and FIA was employed for the simultaneous measurement of glucose and ascorbic acid, respectively, from dialysates of brain tissue.     

纳米金-还原氧化石墨烯修饰葡萄糖氧化酶传感器的制备及其电流法检测饮料中的葡萄糖

利用纳米金(Au NPs)与还原氧化石墨烯(rGO)复合纳米材料制备了葡萄糖氧化酶生物传感器并用于饮料中葡萄糖含量的检测。将壳聚糖作为还原剂及稳定剂,通过一步法合成了Au NPs-rGO复合材料,并通过物理吸附固定葡萄糖氧化酶(GOx)来制作GOx生物传感器。该传感器在磷酸盐缓冲溶液(0.1 mol/L,p H6.0)中,-0.45 V(vs.Ag/Ag Cl)电位下电流法检测葡萄糖含量,线性检测范围为0.01~0.88 mmol/L,灵敏度为22.54μA·mmol-1·L·cm-2,检出限为1.01μmol/L,且表观米氏常数为0.497 mmol/L。该传感器用于多种饮料中葡萄糖含量的直接检测,结果满意。     

Fabrication of Bienzymatic Glucose Biosensor Based on Novel Gold Nanoparticles‐Bacteria Cellulose Nanofibers Nanocomposite

An exploration of gold nanoparticles–bacterial cellulose nanofibers (Au‐BC) nanocomposite as a platform for amperometric determination of glucose is presented. Two enzymes, glucose oxidase (GOx) and horseradish peroxidase (HRP) were immobilized in Au‐BC nanocomposite modified glassy carbon electrode at the same time. A sensitive and fast amperometric response to glucose was observed in the presence of electron mediator (HQ). Both of GOx and HRP kept their biocatalytic activities very well in Au‐BC nanocomposite. The detection limit for glucose in optimized conditions was as low as 2.3 µM with a linear range from 10 µM to 400 µM. The biosensor was successfully applied to the determination of glucose in human blood samples.     

Self-gelatinizable copolymer immobilized glucose biosensor based on prussian blue modified graphite electrode

A novel poly(vinyl alcohol) grafting 4-vinylpyridine self-gelatinizable copolymer was adapted to immobilize glucose oxidase. The reduction of hydrogen peroxide (H2O2) was detected at a Prussian Blue (PB) modified graphite electrode. A stable and sensitive glucose amperometric biosensor is described. The copolymer is a good biocompatible polymer in which the glucose oxidase retains high activity. Moreover, the copolymer can adhere firmly to the inorganic PB membrane. The sensor showed an apparent Michaelis-Menten constant of 18 +/- 0.2 mM and a maximum current density of 1.14 microA cm-2 mM-1. The linear range is from 5 microM to 4.5 mM glucose and the detection limit is 0.5 microM glucose. The catalytic efficiency of PB for the reduction of H2O2 is higher than that for the oxidation of H2O2. Glucose concentrations in serum samples from healthy persons and diabetic patients were determined using the sensor. The results compared well with those provided by the hospital using a spectroscopy method.     

酶法合成的葡萄糖氧化酶-纳米金复合物的直接电化学与生物传感

将NaAuCl₄、葡萄糖氧化酶（GOx）和葡萄糖混合,借一步酶促反应制得吸附GOx的金纳米颗粒（AuNPs）,再通过滴干修饰法研制了Nafion/GOx-AuNPs修饰的玻碳（GC）电极,并考察了该酶电极上GOx的直接电化学和生物传感性能. 这种酶法合成的GOx-AuNPs复合物有良好的酶直接电化学活性,也保持了GOx的生物活性,似可归因于酶法合成的纳米金更接近酶氧化还原活性中心的缘故. 该酶电极在-0.4 V（vs. SCE）电位下,其稳态电流下降与葡萄糖浓度（0.5 4 mmol·L^-1）成正比,检测下限0.2 mol·L^-1.     

Modification of polypyrrole nanowires array with platinum nanoparticles and glucose oxidase for fabrication of a novel glucose biosensor

A novel glucose biosensor, based on the modification of well-aligned polypyrrole nanowires array (PPyNWA) with Pt nanoparticles (PtNPs) and subsequent surface adsorption of glucose oxidase (GOx), is described. The distinct differences in the electrochemical properties of PPyNWA–GOx, PPyNWA–PtNPs, and PPyNWA–PtNPs–GOx electrodes were revealed by cyclic voltammetry. In particular, the results obtained for PPyNWA–PtNPs–GOx biosensor showed evidence of direct electron transfer due mainly to modification with PtNPs. Optimum fabrication of the PPyNWA–PtNPs–GOx biosensor for both potentiometric and amperometric detection of glucose were achieved with 0.2 M pyrrole, applied current density of 0.1 mA cm⁻², polymerization time of 600 s, cyclic deposition of PtNPs from −200 mV to 200 mV, scan rate of 50 mV s⁻¹, and 20 cycles. A sensitivity of 40.5 mV/decade and a linear range of 10 μM to 1000 μM (R² = 0.9936) were achieved for potentiometric detection, while for amperometric detection a sensitivity of 34.7 μA cm⁻² mM⁻¹ at an applied potential of 700 mV and a linear range of 0.1–9 mM (R² = 0.9977) were achieved. In terms of achievable detection limit, potentiometric detection achieved 5.6 μM of glucose, while amperometric detection achieved 27.7 μM.     

Glucose Microbiosensor Based on MnO2 and Glucose Oxidase Modified Carbon Fiber Microelectrode

A glucose microbiosensor has been developed using electrochemical codeposition of glucose oxidase (GOx) along with MnO₂ as mediator, onto a single carbon fiber microelectrode. A two‐step deposition of only MnO₂ initially and then of MnO₂ in the presence of GOx has been introduced to ensure appropriate activity of the mediator. Several parameters such as deposition potential and time, concentration levels etc. have been characterized and optimized. A thin Nafion film was applied as an immobilization/encapsulation and interference‐free protective layer. The proposed microbiosensor was employed as an amperometric glucose detector at pH 7.5 at an operating potential of +0.58 V (vs. Ag/AgCl). The microbiosensor is characterized by a well‐reproducible amperometric response, linear signal‐to‐glucose concentration range from 1.5 mmol L^?1 to 15 mmol L^?1, and a limit of detection (S/N=3) of 0.8 mmol L^?1. The microbiosensor exhibits good stability over more than ten hours of continuous measurement.     

Prussian Blue Modified Carbon Ionic Liquid Electrode: Electrochemical Characterization and Its Application for Hydrogen Peroxide and Glucose Measurements

Prussian blue modified carbon ionic liquid electrodes (PB‐CILEs) were fabricated using chemical and electrochemical procedures. Chemically fabricated PB‐CILE exhibited an excellent sensitivity (0.0866 μA μM^?1), low detection limit (0.01 μM) and two linear ranges (0.01–1 and 1–600 μM) toward hydrogen peroxide. Then, glucose oxidase (GOx) was immobilized on the surface of PB‐CILE to fabricate glucose biosensor using three different procedures involving cross linking with glutaraldehyde (GLU) and bovine serum albumin (BSA), entrapment into the Nafion matrix and covering with a sol‐gel layer. Glucose biosensor fabricated using cross linking procedure showed the best sensitivity (0.0019 μA μM^?1) and operational stability for glucose.     

Sol–gel immobilized enzymatic glucose biosensor on gold interdigitated array (IDA) microelectrode

An enzymatic glucose biosensor with good sensitivity, selectivity and stability employing interdigitated array microelectrode (IDA μ-electrode) was reported. IDA μ-electrode was prepared by photolithography method with its surface immobilized with a layer of glucose oxidase (GOx), entrapped in a three-dimensional network composed of chitosan and tetraethyl orthosilicate sol–gel. The surface of the as-prepared IDA μ-electrode was characterized by scanning electron microscope, electron spectroscopy for chemical analysis, and atomic force microscopy. The experimental parameters for the best glucose sensing performance were optimized according to the loading of GOx, the applied voltages, the concentration of mediator, and the pH for glucose detection. The resulted biosensor exhibited a good response to glucose with a wide linear range from 0 to 35 mM and a low detection limit of 1 mM. The glucose sensor also showed a short response time (within 5 s) that the fast response was reflected by the small Michaelis–Menten constant (K_M ^app) with a value of 2.94 mM. The reported glucose biosensor exhibited good sensitivity (8.74 μA/mM.cm²), reproducibility, and stability.