Segmental dynamics in poly(methyl acrylate) on silica: molecular-mass effects

The effect of molecular mass on the segmental dynamics of poly(methyl acrylate) (PMA) adsorbed on silica was studied using deuterium quadrupole-echo nuclear magnetic resonance (NMR) and modulated differential scanning calorimetry. Samples adsorbed on silica (all about 1.5 mg PMA/m2 silica) were shown to have more restricted segmental mobility, and higher Tg's, than the corresponding bulk PMA samples. Around the glass-transition region, adsorbed samples exhibited segmental mobility, which could be classified as heterogeneous due to a superposition of more-mobile and less-mobile components present in the deuterium NMR spectra. This heterogeneity was consistent with a motional gradient with more-mobile segments near the polymer-air interface and the less-mobile species near the polymer-silica interface. The mobility of the adsorbed 77 kDa PMA sample was the lowest among the four different molecular-mass samples studied. Samples studied with masses both larger and smaller than 77 kDa had larger mobile-component fractions in the adsorbed polymer. The additional mobility was attributed to the presence of either longer tail and loop conformations in the higher molecular-mass samples or the inherent mobility of the tails in the lower molecular-mass samples on the surface.     

Segmental dynamics of interfacial poly(methyl acrylate)-d(3) in composites by deuterium NMR spectroscopy.

The interface in composite materials containing an ultrathin layer of poly(methyl acrylate)-d(3) (PMA-d(3)) on silica was studied using deuterium NMR. PMA-d(3) was deposited from solution at saturation coverage from toluene onto silica. The samples were dried and composite samples made by hot pressing the PMA-d(3)/silica samples with hydrogenated polystyrene (PS) and high (HMW) and low (LMW) molecular weight hydrogenated poly(methyl acrylate) (PMA) as the overlayer. The interfacial layers of PMA-d(3) were studied at the air-polymer-silica and polymer-polymer-silica interfaces using deuterium solid-state quadrupole-echo NMR and the results compared to those for the bulk polymer. It was found that for samples at the air-polymer-silica interface, some of the polymer segments in the surface sample had segmental mobility higher than that of the corresponding bulk PMA-d(3) sample at the same temperature. When overcoated with unlabeled polymer, the interfacial polymer at the polymer-polymer-silica interface showed reduced mobility due to the presence of the overlayer. The adsorbed PMA-d(3), in the composite samples, decreased in mobility in the order of LMW-PMA > HMW-PMA > PS. The PS sample caused the greatest reduction in the PMA-d(3) interfacial mobility. The order was consistent with the segmental mobilities of the polymers used for the overlayers. The lower the mobility of the polymer used for the overlayer, the more restricted were the polymer segments in the adsorbed PMA-d(3) layer.     

Segmental dynamics of poly(methyl acrylate)-d3 adsorbed on anopore: a deuterium NMR study

The segmental dynamics of poly(methyl acrylate-d3) (PMA-d3) adsorbed in the pores of anopore membranes has been investigated using deuterium NMR over the temperature range 25-80 degrees C. The onset of the NMR glass-transition temperature (Tg) for the adsorbed samples was approximately 15 degrees C higher than that for the bulk sample. The adsorbed polymer contained segments with restricted mobility (glassy), even at the highest temperatures studied, at which the bulk polymer showed only mobile segments. The spectra from samples with different adsorbed amounts of PMA-d3, between 1.1 and 4.2 mg/m2, were similar in their temperature-dependent mobilities. Neither was there much difference in the spectra of PMA-d3 on anopore samples with pore sizes of 0.2 and 0.02 microm. However, for a solvent-washed sample with an adsorbed amount of 0.7 mg/m2, additional restriction in PMA-d3 mobility was observed.     

The effect of poly(N,N-dimethylacrylamide) on the lamellar phase of Aerosol OT/water

The effect of a water-soluble uncharged polymer on the stability of the lamellar phase of the Aerosol OT (AOT)/water system is studied. The lamellar phase still exists when water is replaced by an aqueous solution of poly(N,N- dimethylacrylamide) (R_gƼ᎒² Å). Since the coil dimensions are (much) larger than the thickness of the water layers (d_wᅣ Å), the polymer molecules do not enter the lamellar phase. Instead segregation in small domains occurs, and in equilibrium with the AOT-rich phase another separate phase containing the polymer is formed. The polymer-rich phase exerts an osmotic pressure that reduces the water content in the AOT-rich phase, and by compression the repeat distance is reduced.     

Low-temperature suspension polymerization of vinyl pivalate for the preparation of syndiotacticity-rich ultrahigh molecular weight poly(vinyl alcohol) microfibrils with high yield

To prepare ultrahigh molecular weight (UHMW) poly(vinyl pivalate) (PVPi) with high conversion and high linearity for a precursor of syndiotacticity-rich UHMW poly(vinyl alcohol) (PVA), vinyl pivalate (VPi) was suspension polymerized using a low-temperature initiator, 2,2'-azobis(2,4-dimethylvaleronitrile) (ADMVN), and the effects of polymerization conditions on the polymerization behavior and molecular structures of PVPi and PVA prepared by saponifying PVPi were investigated. Suspension polymerization was slightly inferior to bulk polymerization in increasing the molecular weight of PVA. In contrast, the former was superior in increasing the conversion of the polymer. Suspension polymerization of VPi at 25 °C by controlling various polymerization factors proved to be successful in obtaining PVA of UHMW (number-average degree of polymerization (P_n): 14,700-16,700), high syndiotactic diad content (62%), and of high yield (ultimate conversion of VPi into PVPi: 85-90%). In the case of bulk polymerization of VPi under the same conditions, maximum P_n, conversion of 15,800-17,000, and 25-35% were obtained, respectively. The degree of branching was lower and the P_n and syndiotacticity were higher with PVA prepared from PVPi polymerized at lower temperatures. All PVAs from PVPi suspension-polymerized at 25 °C were fibrous, with a high degree of crystallinity and orientation of the crystallites.     

Effects of molecular mass and surface treatment on adsorbed poly(methyl methacrylate) on silica

The behavior of relatively monodisperse adsorbed poly(methyl methacrylate) (PMMA) samples, from 19 to 587 kDa on silica, was studied using modulated differential scanning calorimetry and FTIR. On untreated Cab? O? Sil silica, the glass transition temperatures (T_gs) were higher (by around 30 °C), and the transitions were significantly broader (by a factor of 5–6) than those for the corresponding bulk samples. While the T_gs for the bulk polymers showed the expected dependence on molecular mass, the polymers on untreated silica showed little dependence, i.e., at the same adsorbed amounts, the glass transitions were very similar. The FTIR spectra of the adsorbed PMMA (on untreated silica) showed the presence of at least two resonances, one for the bound (hydrogen bonded to surface silanols) and another for free carbonyls. Fitting of the spectra allowed the estimation of the bound fractions of carbonyls that were dependent on the adsorbed amount, but not molecular mass. On Cab? O? Sil treated with hexamethyldisilizane (HMDS), the adsorbed PMMA exhibited glass transition behavior with little molecular‐mass dependence; the T_gs for the different PMMA samples were very similar to those of the high‐molecular mass bulk polymer, but with additional broadening of about a factor of 2. FTIR spectra for the PMMA samples on the treated silica did not show significant amounts of any of the hydrogen‐bonded carbonyl groups. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 649–658, 2008     

Characterization and degradation of poly(methylphenylsiloxane)–poly(methyl methacrylate) interpenetrating polymer networks

Poly(methylphenylsiloxane)–poly(methyl methacrylate) interpenetrating polymer networks (PMPS–PMMA IPNs) were prepared by in situ sequential condensation of poly(methylphenylsiloxane) with tetramethyl orthosilicate and polymerization of methyl methacrylate. PMPS–PMMA IPNs were characterized by infrared (IR), differential scanning calorimetry (DSC), and ²⁹Si and ¹³C nuclear magnetic resonance (NMR). The mobility of PMPS segments in IPNs, investigated by proton spin–spin relaxation T₂ measurements, is seriously restricted. The PMPS networks have influence on the average activation energy E_a,av of MMA segments in thermal degradation at initial conversion. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1717–1724, 1999     

Stereoregularity of radically polymerized poly(alkyl acrylates) and poly(trimethylsilyl acrylates) and the preparation of syndiotactic poly(methyl acrylate)

Nuclear magnetic resonance (NMR) spectroscopy was used to determine the stereoregularity of radically polymerized poly(ethyl acrylates), poly(trimethylsilyl acrylates), and poly(isopropyl acrylate-α,β-d₂). The ethyl acrylate polymers consisted of a random configuration having about 50% of isotactic diads, and their stereoregularities were independent of the polymerization temperature (40 to ?78°C). Poly(trimethylsilyl acrylates) and poly(isopropyl acrylate-α,β-d₂) prepared at low temperatures had a syndiotactic configuration. Syndiotactic poly(methyl acrylate) was derived from syndiotactic poly(trimethylsilyl acrylate). For poly(methyl acrylate), an approximate estimation of the stereoregularity by infrared spectroscopy was proposed.     

Structure and molecular motion of poly(ethylene oxide) chains adsorbed on a silica-tethered poly(methyl methacrylate) by the spin label method

The spin-label method was used to study the structure and molecular motion of poly(ethylene oxide) (PEO) chains adsorbed on a silica-tethered poly(methyl methacrylate) (PMMA). Spin-labelled PEO with a narrow molecular weight distribution, having number averaged molecular weight (M _N)=6.0×10³, was adsorbed on the surface of the silica-tethered PMMA with various grafting ratios in carbon tetrachloride solution at 35?°C. ESR spectra were measured at various temperatures after the samples were completely dried. The ESR spectra are composed of two spectra arising from spin-labels attached to “train” and “tail” segments, which are strongly and weakly interacted with the silica surface, respectively. The fractional amount of the “tail” segments increases extremely with the grafting ratio of PMMA. Molecular mobility of the PEO chains estimated from the temperature dependence of the ESR spectra also decreases significantly with the grafting ratio of PMMA. Structure and molecular motion of the PMMA chains tethered on the silica were also studied using the spin-labelled PMMA. Consequently, parts of the PEO segments penetrate into the PMMA chains and is adsorbed on the silica surface (“train” segments), whereas parts of the PMMA segments protrude from the surface. The other PEO segments are entangled with the tethered PMMA chains (“tail” segments).     

Thermal analysis and FT‐IR studies of adsorbed poly(ethylene‐stat‐vinyl acetate) on silica

Adsorbed poly(ethylene‐stat‐vinyl acetate) (PEVAc) on fumed silica was studied using temperature‐modulated differential scanning calorimetry (TMDSC) and FT‐IR spectroscopy. The properties of the copolymers were compared with poly(vinyl acetate) (PVAc) and low density polyethylene (LDPE) as references. TMDSC analysis of the copolymer‐silica samples in the glass transition region was complicated for the copolymers because of the ethylene crystallinity. Nevertheless, examination of the glass transition region for small adsorbed amounts of these copolymers indicated the presence of tightly‐ and loosely‐bound polymer segments, similar to other polymers which have an attraction to silica. Compared with bulk polymers with the same composition, the tightly‐bound polymers showed an increased glass transition temperature (T_g) and a loosely‐bound fraction with a lower T_g than bulk. FT‐IR spectra of the surface copolymers indicated that the fraction of bound carbonyls (p) increased as the fraction of vinyl acetate in the copolymers decreased, consistent with the notion that the carbonyls from vinyl acetate preferentially find their way to the silica surface. Spectra from samples with different adsorbed amounts of polymer were used to obtain the amount of bound polymer (M_b) and the ratio of molar absorption coefficients of bound carbonyls to free carbonyls (X). The copolymers had very large p values (up to 0.8) at small adsorbed amounts and dependent on the composition of the polymer. However, an analysis of the bound fractions, based on only the vinyl acetate groups, superimposed the data, suggesting that the ethylene units simply dilute the vinyl acetate groups in the surface polymer. The sample with the smallest fraction of vinyl acetate did not show this behavior and may be considered to be “carbonyl poor.” © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 727–736     

Branching of anionic poly(methyl methacrylate)

A viscometric determination of the degree of branching γ, of poly(methyl methacrylate) obtained by anionic polymerization proved the reaction of the growing center of poly(methyl methacrylate) with the ester group of another polymer molecule, accompanied by the formation of a trifunctional branch point. This reaction occurs if the solution polymerization of methyl methacrylate is initiated: (1) with butyllithium at ?78°C only on attaining 100% conversion and after a long time or at +20°C immediately after the polymerization has set in; (2) with lithium tert-butoxide at +20°C after a long time. The degree of branching of poly(methyl methacrylates) obtained under similar conditions in the presence of tetrahydrofuran reaches higher values than for polymers prepared in toluene. The tacticity of polymers does not affect the experimentally determined γ values.     

Ion conductivity studies of blends of poly(methyl methacrylate)-g-poly(ethylene glycol) and poly(ethylene glycol) complexed with LiCF3 SO3

Polymer electrolytes which are adhesive, transparent, and stable to atmospheric moisture have been prepared by blending poly(methyl methacrylate)-g-poly(ethylene glycol) with poly(ethylene glycol)/LiCF₃ SO₃ complexes. The maximum ionic conductivities at room temperature were measured to be in the range of 10⁻⁴ to 10⁻⁵ s cm⁻¹. The clarity of the sample was improved as the graft degree increased for all the samples studied. The graft degree of poly(methyl methacrylate)-g-poly(ethylene glycol) was found to be important for the compatibility between the poly(methyl methacrylate) segments in poly(methyl methacrylate)-g-poly(ethylene glycol) and the added poly(ethylene glycol), and consequently, for the ion conductivity of the polymer electrolyte. These properties make them promising candidates for polymer electrolytes in electrochromic devices. © 1996 John Wiley & Sons, Inc.     

Stereoregularity of poly(methyl acrylate)

The stereoregularity of poly(methyl acrylate) and poly(methyl acrylate-αd) was determined from the NMR spectra. A method of quantitative determination of stereoregularity of poly(methyl acrylate) proposed in this paper is based on the fact that in the 100 Mc./sec. NMR spectrum the absorption peaks due to methylene protons in syndiotactic configurations overlap absorptions due to only one of two methylene protons in isotactic configurations. The stereostructure of poly(methy1 acrylates) polymerized with anionic catalysts such as Grignard reagents, n-butyllithium, and LiAlH₄ is generally richer in isotactic diads than in syndiotactic diads. For example, poly(methyl acrylate) polymerized with phenylmagnesium bromide as catalyst at ?20°C. consists of 99% isotactic and 1% syndiotactic diads. In radical polymerization, the isotacticity of poly(methyl acrylate) is independent of polymerization temperature. Poly(methyl acrylates) polymerized with a Ziegler-Natta catalyst consisting of Al(C₂H₅)₂Cl and VCl₄ have configurations similar to those polymerized by radical initiators. The stereoregularity of poly(methyl acrylate-α-d) resembled that of poly(methyl acrylate) polymerized under the same conditions.     

Molecular mass and dynamics of poly(methyl acrylate) in the glass-transition region

The segmental dynamics of bulk poly(methyl acrylate) (PMA) were studied as a function of molecular mass in the glass-transition region using 2H NMR and modulated differential scanning calorimetry (MDSC). Quadrupole-echo 2H NMR spectra were obtained for four samples of methyl-deuterated PMA-d3 with different molecular masses. The resulting spectra were fit using superpositions of simulated spectra generated from the MXQET simulation program, based on a model incorporating nearest-neighbor jumps from positions on the vertices of a truncated icosahedron (soccer-ball shape). The lower molecular-mass samples, influenced by the presence of more chain ends, showed more heterogeneity (broader distribution) and lower glass transitions than the higher molecular-mass samples. The MDSC experiments on both protonated and deuterated samples showed behavior consistent with the NMR results, but temperature shifted due to the different frequency range of the measurements in terms of both the position and breadth of the glass transition as a function of molecular mass.     

Effect of the molecular weight of poly(vinyl alcohol) on the water stability of a syndiotactic poly(vinyl alcohol)/iodine complex film

To precisely identify the effect of the molecular weight of syndiotactic poly(vinyl alcohol) (s-PVA) on the water stability of a s-PVA/iodine complex film, we prepared four s-PVAs with similar syndiotactic diad (s-diad) contents of about 63% and with different number-average degrees of polymerization, P_n, of 900, 6,000, 10,000, and 17,000, respectively. The desorption behavior of iodine in the s-PVA/iodine complex film in water was investigated in relation to the solubility of s-PVA in water. The degree of solubility of a s-PVA film having different P_n in water at 80 °C was limited to about 0.3-10%, whereas the degrees of solubility of atactic PVA films with P_n of 6,000 and 10,000 were 100% at the same conditions. The degree of iodine desorption of the complex film decreased with increasing P_n of s-PVA. Especially, the degree of iodine desorption of a PVA drawn film having P_n of 17,000 was limited to 2%, regardless of soaking temperature from 40 to 80 °C. The desorption of iodine in water was strongly affected by the dissolution of PVA. In addition, the degree of iodine desorption of the drawn s-PVA/iodine film was larger than that of the undrawn one.     

Synthesis and thermal properties of poly(methyl methacrylate)-graft-(cellobiosylamine-C15)

Model experiments for synthesis of a comb-shaped copolymer with cellulose side-chains were performed with cellobiose derivatives. A novel cellobiose monomer, N-(15-methacryloyloxypentadecanoyl)-2,3,6-tri-O-acetyl-4-O-(2,3,4,6-tetra-O-acetyl-β-d-glucopyranosyl)-β-d-glucopyranosylamine (2) was prepared from heptaacetylcellobiosyl- amine. Homopolymerization of cellobiose monomer 2 and copolymerization of monomer 2 with methyl methacrylate (MMA) were performed using 2,2′-azobis(isobutyronitrile) (AIBN) as an initiator to obtain homopolymers 3-i (i = 1–4) and copolymers 3-i (i = 5–7), poly(methyl methacrylate)-graft-(heptaacetylcellobiosylamine-C15). The size exclusion chromatography—multi-angle laser light scattering (SEC-MALS) measurements revealed that comb-shaped homopolymers 3-i (i = 1–4) had more compact structures compared to copolymers 3-i (i = 5–7) at the same elution volume. Selective deacetylation of polymers 3-i (i = 1–7) gave novel cellobiose polymers 4-i (i = 1–7), poly(methyl methacrylate)-graft-(cellobiosylamine-C15). The amide linkages between cellobiose moiety and long-chain alkyl group, and the ester linkages between PMMA main-chain and long-chain alkyl group remained after deprotection. The differential scanning calorimetry (DSC) measurements revealed that the T _gs of the polymers 4-i (i = 1, 5, 6, 7) increased with increasing cellobiose composition in the polymers. It was indicated that cellobiose moieties of polymers 4-i (i = 1, 5, 6, 7) reduced the mobility of PMMA main-chain.     

Structure of poly(methyl methacrylate) chains adsorbed on sapphire probed using infrared-visible sum frequency generation spectroscopy

We have studied the orientation of the train segments of a poly(methyl methacrylate) (PMMA) adsorbed layer at the CCl4-sapphire interface using surface-sensitive IR-visible sum frequency generation (SFG) spectroscopy. The SFG spectra of PMMA chains adsorbed on sapphire indicate ordered ester methyl groups. In comparison, we did not observe any significant contributions from the backbone methylene and alpha methyl groups, suggesting that these groups are disordered. No change in the structure of the adsorbed layer is observed upon cooling the solvent below the theta temperature; this is consistent with the picture of flat adsorbed chains on the surface. Interestingly, the orientation of the ester methyl groups of a spin-coated PMMA film at the PMMA-sapphire interface is similar to that of the same groups in the chains adsorbed from solution.     

Grafting of poly(ethylene oxide) on poly(methyl methacrylate) by transesterification

The grafting of the potassium alkoxide derivative of poly(ethylene oxide) on poly(methyl methacrylate) in homogeneous solution in toluene was studied. The alkoxide was prepared by reaction with potassium metal with methanolic potassium methoxide, or with potassium naphthalene. The last was the most suitable for the systematic investigation of the grafting process. Soluble graft polymers were formed, and essentially the initial poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) participated in the production of graft polymer. The composition of the graft polymers and the frequency of grafting of the side chains were determined by NMR. The solubility of the graft polymers in methanol and water increased with increasing PEO contents, while the melting ranges decreased. Fractionation of the crude graft polymers showed that the grafting reaction was random, and graft polymers containing one PEO side chain per about 10–170 MMA units were obtained.     

Microhardness measurements of poly(methyl methacrylate) and poly(vinylidene fluoride) polyblends

The preparation of polymer blends of poly(methyl methacrylate) and poly(vinylidene fluoride) in different weight percentages is described. Vickers microhardness measurements have been made to study the effects of load and compositional ratio of the two polymers in polyblend. It is observed that poly(vinylidene fluoride) acts as a plasticizer for poly(methyl methacrylate). Evidence of increasing and decreasing strength of polyblends has been obtained for different compositional ratios of the two polymers.     

Synthesis and solution properties of comblike polymers from octadecyl methacrylate and acrylic acid

Amphiphilic polymers consisting of a statistical distribution of octadecyl methacrylate (ODMA) and acrylic acid in respective molar ratios of 83-22 and 17-78 mol% and in a molecular-weight range of 2.35-4.70᎒⁴ gmol^-1 have been synthesized. The series of polymers consisting of various mole fractions of ODMA and acrylic acid are expected to exhibit unique characteristics resembling ionomer to hydrophobically modified polyelectrolytes. The changes in the I₃/I₁ emission intensity ratios of pyrene, occurring in the presence of tetrahydrofuran (THF) solutions of the polymers have been taken as the main basis for inferring solution structures. The polymers are found to form random-coil to collapsed-coil/aggregated structures in THF solvent depending on the copolymer compositions. The polymer consisting of 83 mol% ODMA and 17 mol% acrylic acid behaves as an ionomer, capable of forming collapsed-coil structures at concentrations of 0.02 gml^-1 and above as shown by a very high I₃/I₁ of 1.20 (I₃/I₁ of pyrene in THF is 0.85). In contrast, the poly(octadecyl methacrylate) homopolymer and the sets of copolymers consisting of a very high proportion of acrylic acid to an extent of 73 mol% and above contribute to almost negligible or very small changes in I₃/I₁ similar to the homopolymer, poly(octadecyl methacrylate), suggesting the formation of random-coil structures.