Synthesis of silica adsorbent and its selective separation for flavone

One kind of built-in silica adsorbent, which has high adsorption selectivity to rutin, was synthesized using molecular imprinting technology by the following steps: synthesis of precursor from the reaction between water soluble rutin (as template molecule) and the functional monomer chloropropyltriethoxysilane, co-hydrolysis of the precursor and tetraethoxysilane (TEOS), sol-gel aging process, and removal of template molecules. The results of adsorption experiment show that this adsorbent has a high adsorption capacity for rutin, and good adsorption selectivity towards rutin even under the interference of a flavone with a similar structure. TEM photos suggest that nanocaves corresponding to rutin were formed inside the adsorbent while FTIR spectra indicate that new bond was generated during the recognition process. __________ Translated from Journal of Tianjin University, 2007, 40(4): 411–415 [译自: 天津大学学报]     

汽油活性炭基脱硫吸附剂的制备与评价

以250℃温度下浓硫酸改性后的活性炭为载体,采用浸渍法制备了以MnO₂为活性组分的活性炭基的汽油脱硫吸附剂MnO₂/AC,考察了吸附剂的制备条件及脱硫条件对脱硫效果的影响。研究结果表明,适宜的吸附剂制备条件为,以Mn(NO₃)₂为活性组分前驱物,Mn(NO)₂浸渍液浓度0.15mol/L、常温下浸渍24h、焙烧温度350℃、焙烧时间2h。该吸附剂在静态吸附温度120℃、吸附时间2h、剂油质量比0.10的条件下可使原料油硫的质量分数从628.6×10^-6降至221.5×10^-6,脱硫率达到64.8%;在动态吸附温度60℃、空速1.76h^-1的条件下,初始流出汽油硫的质量分数降至21.8×10^-6,初始脱硫率达到96.5%。     

低温一步法活性炭基脱硫剂的制备与评价

以木屑为原料,在低温条件下一步法制得活性炭基吸附剂,考察了吸附剂制备条件和液-固、气-固吸附条件对吸附剂脱硫性能的影响。结果表明,吸附剂的最佳制备条件为,浸渍液与木屑质量比为1：1,浸渍液中硝酸质量分率为30%、吸附剂表面NiO负载量为5%,常温下浸渍24 h,400℃焙烧3 h。该吸附剂在0.2 g吸附剂/10 mL模拟油、温度为40℃及时间为5 h的液-固吸附脱硫的条件下,脱硫率为28.36%,吸附四次后饱和吸附硫容量可达2.34 mgS/g;在气-固吸附温度为250℃、空速为6.3 h^-1的条件下,饱和吸附硫容量为2.37 mgS/g;高温气-固吸附脱硫对吸附剂的影响表明,与脱硫前相比,吸附剂在比表面积、总孔体积、微孔体积均有明显提高,这说明气-固吸附脱硫过程同时实现了活性炭的扩孔活化。甲苯溶剂再生实验表明,经五次再生后吸附剂的再生性能均可达90%以上。     

Preparation of anhydrotrypsin-immobilized diol silica as a selective adsorbent for high-performance affinity chromatography of peptides containing arginine or lysine at their C-termini

Summary Anhydrotrypsin (AHT), a catalytically inert derivative of trypsin in which the active site serine residue was converted to dehydroalanine residue by chemical modification, was immobilized onto diol silica through the activation with trifluoroethanesulfonyl chloride, and an AHT-diol-silica column was used for high-performance affinity chromatography separation of peptides containing arginine or lysine at their C-termini from the others. Improved separation in terms of speed was accomplished.     

一种确定煤基吸附剂内各扩散系数的简易方法

多孔介质内的扩散有分子扩散和表面扩散两种。在吸附温度较高时 ,表面扩散可忽略 ,而在温度较低的吸附过程中 ,两种扩散均须考虑。Ｓｃｈｎｅｉｄｅｒ和Ｓｍｉｔｈ[1 ] 曾用色谱法探讨了一种计算扩散系数的方法。他们认为等温吸附呈线性变化 ,引入了曲折系数 ,计算出分子扩散系数 (下称气相扩散系数 ) ,表面扩散系数 (下称吸附相扩散系数 )则由综合扩散系数减去分子扩散系数得到。文献 [2 ]则认为吸附过程非线性变化 ,服从Ｆｒｕｎｄｌｉｃｈ方程或Ｌａｎｇｍｕｉｒ方程。从质量平衡方程得出相对吸附量方程 ,再求出各扩散系数。前一种方法将…     

固定化牛血清白蛋白吸附材料的制备及其对胆红素的吸附性能

降低高胆红素血症和重症肝炎患者血液中异常升高的胆红素浓度是血浆交换和血液灌流等疗法的目标之一。本文通过共价键合的方法将牛血清白蛋白(BSA)固定在甲基丙烯酸缩水甘油酯共聚三羟甲基丙烷三甲基丙烯酸酯[poly(GMA-co-TMPTMA)]大孔树脂微球上,制备得到对胆红素具良好吸附性能的固定化BSA吸附材料(BIA),吸附容量达48.7mg/g。由于血清白蛋白对胆红素的强烈相互作用,胆红素溶液中游离BSA的存在会显著降低BIA对胆红素的吸附量。BIA对胆红素的吸附量随吸附温度升高而增加。BIA在-80℃下储存31d后性能仍然稳定,对胆红素的吸附量几乎不变。上述结果表明所制备的BIA为以特异性吸附胆红素为目的的血液净化材料提供了新的选择。     

笼形聚偕氨肟树脂吸附溴和碘

用酸、碱处理的笼形聚偕氨肟树脂（ACAO、BCAO）吸附溴和碘,发现它们的吸附能力无显著差别。吸附客量与溴和碘浓度关系符合Freundlich方程．从扫描电子显微镜观察到碘在树脂表面形成微晶．联系到溴和碘的超当量吸附现象,初步认为,它们是通过物理吸附在树脂表面富集。     

Design and synthesis of affinity ligands and relation of their structure with adsorption of proteins

Affinity chromatography has played an increasingly important role both in the pharmaceutical industry and academic research. In the present study, we report our preliminary investigation on the relationship between the affinity ligand structure and its adsorption to multi-protein samples. The structure of the ligands, including the size of the ring (cyclic group) and the length of the chain (linear group), has a great impact on the adsorption of ligands to proteins. Meanwhile, the functional groups that the ligands carry are also closely related to the adsorption of ligands to proteins. This research provides good guidance for the design and synthesis of affinity materials in affinity chromatography. It is also useful to other protein-ligand interaction-related research.     

Tailoring the volatility and stability of oligopeptides

Amino acids are essential building blocks of life, and fluorinated derivatives have gained interest in chemistry and medicine. Modern mass spectrometry has enabled the study of oligo‐ and polypeptides as isolated entities in the gas phase, but predominantly as singly or even multiply charged species. While laser desorption of neutral peptides into adiabatically expanding supersonic noble gas jets is possible, UV–VIS spectroscopy, electric or magnetic deflectometry as well as quantum interferometry would profit from the possibility to prepare thermally slow molecular beams. This has typically been precluded by the fragility of the peptide bond and the fact that a peptide would rather ‘fry’, i.e. denature and fragment than ‘fly’. Here, we explore how tailored perfluoroalkyl functionalization can reduce the intermolecular binding and thus increase the volatility of peptides and compare it to previously explored methylation, acylation and amidation of peptides. We show that this strategy is essential and enables the formation of thermal beams of intact neutral tripeptides, whereas only fragments were observed for an extensively fluoroalkyl‐decorated nonapeptide. © 2017 The Authors. Journal of Mass Spectrometry Published by John Wiley & Sons Ltd.     

功能化程序对笼形聚偕氨肟树脂吸附和吸留性质的影响

聚丙烯颗粒在水溶液中与丙烯腈和二乙烯基苯反应,得接枝交联产物（Ⅰ）。Ⅰ被氨肟化再经成笼反应．得笼形聚偕氨肟树脂（Ⅱ）。笼内仅吸留易于除去的溶剂丙酮。若Ⅰ成笼后再氨肟化,所得吸收剂（Ⅲ）将吸留大量的羟胺,它缓慢地释放出来,干扰吸收剂对酸、碱离子或分子吸附容量的测定。Ⅱ对一些离子例如Hg2+和MnO4-的吸附能力与Ⅲ不同,被认为是两者的网络结构不同所致。     

Application of a novel affinity adsorbent for the capture and purification of recombinant Factor VIII compounds

Recombinant Factor VIII (FVIII) therapies have been created to provide treatment for Hemophilia A, an inherited bleeding disorder caused by mutation in the FVIII gene. A major challenge in the purification of recombinant FVIII molecules is the development of an affinity chromatography step. Such a step must be highly specific and selective for the FVIII molecule, but also must be designed appropriately to ensure the FVIII molecule can be effectively recovered without resorting to harsh elution conditions which may be harmful to the product. Additionally, it is desirable to have affinity adsorbents designed to be reusable over a large number of column cycles while maintaining consistent purification performance. In this work, we describe the use of VIIISelect, a commercially available affinity adsorbent designed specifically for the purification of FVIII compounds. The VIIISelect adsorbent consists of a 13 kDa recombinant protein ligand attached to a cross-linked agarose base matrix. The structure of the recombinant ligand is based upon Camelid-derived single domain antibody fragments. The VIIISelect adsorbent is produced using a process free of animal-derived raw materials, which is a highly desirable attribute for adsorbents used in the purification processes of recombinant protein therapeutics. The VIIISelect adsorbent was used as the initial capture column to purify a FVIII compound directly from clarified cell culture fluid prior to further downstream purification. The purification performance of the VIIISelect was evaluated, which included measurement of the static binding capacity, dynamic binding capacity, product recovery, impurity clearance, and adsorbent reuse. Following laboratory-scale process development, the VIIISelect adsorbent was scaled up and used in the large scale manufacturing of a FVIII compound.     

Preparation of β-cyclodextrin sulfate-immobilized hydrophilic vinyl-polymer gel as a selective,high recovery and stable adsorbent for high-performance affinity chromatography of heparin-binding substances

Summary β-Cyclodextrin sulfate having heparin-mimicking activity was immobilized on a hydrophilic vinyl-polymer gel, TSKgel AF-Epoxy, TOYOPEARL 650M. A column packed with this material could be used for high-performance affinity chromatographic separation of heparin-binding substances such as growth factors, enzymes, coagulation factors and lipoproteins. The substances retained on the column were recovered more easily than those on a heparin-immobilized column. Furthermore, the β-Cyclodextin sulfate-immobilized gel was superior in stability to the heparin-immobilized gel when exposed to acidic and basic solutions.     

Design and synthesis of immobilized Tamiflu analog on resin for affinity chromatography

A resin linked with the Tamiflu core was synthesized by modifying our original synthetic route of oseltamivir phosphate (Tamiflu). The prepared resin bound to the influenza virus enzyme neuraminidase, the main target of Tamiflu. The immobilized Tamiflu analog will be useful for isolating and identifying presumed endogenous vertebrate proteins that interact with Tamiflu, which might relate to the abnormal behavior exhibited by some influenza patients treated with Tamiflu.     

Efficient removal of MB dye using litchi leaves powder adsorbent: Isotherm and kinetic studies

Removal of Methylene Blue (MB) dye using Litchi Leaves Powder (LLP) material was carried out in batch mode. Effect of the mass of the adsorbent (0.1–2.5 g/L), pH of the solution (2−12), starting concentration of MB dye (50–150 mg/L), ionic strength using NaCl (0.1–0.5 M) as an electrolyte, contact time (0–60 min) on the adsorption of MB dye was studied. To calculate pH at which LLP material surface becomes neutral point of zero charge (pH_pzc) is also determined and found to be 6.48. Removal process best fit in the pseudo-second-order kinetic model as indicated by its higher R² value (0.999). Isotherm models (Freundlich and Langmuir) were fitted to the data obtained from the experiment to understand the adsorption behaviour. Result shows that experimental data were fitted to the both isotherm models (Freundlich and Langmuir) as indicated by higher R² value for both Freundlich (0.991) and Langmuir (0.994) model, and it was determined that LLP has a maximum adsorption capacity of 119.76 mg/g.     

Preparation of anhydrochymotrypsin diol silica as selective adsorbent for affinity chromatography of peptides with aromatic amino acids at C-termini

Summary Anhydrochymotrypsin (AHC), a catalytically inert derivative of chymotrypsin in which the serine-residue active site has been converted chemically to a dehydroalanine residue, was immobilized on diol silica by activation with trifluoroethanesulfonyl chloride. A AHC-diol-silica column was used for high-performance affinity chromatographic separation of peptides with aromatic amino acids at their C-termini from other peptides. Faster separations were achieved.     

Fe3O4@chitosan-bound boric acid composite as pH-responsive reusable adsorbent for selective recognition and capture of cis-diol-containing shikimic acid

Recently, shikimic acid (SA) has aroused great concern as the starting raw material for the synthesis of antiviral drug (Tamiflu) against the spread of influenza virus in the body. In this work, magnetic chitosan composite modified with boric acid and its application in SA recognition and separation was described. Chitosan (CT) with plenty of hydroxyl and amino groups was first coated on the surface of magnetic core Fe₃O₄, then carboxylic groups were grafted to the surface of Fe₃O₄@CT via anhydride modification, followed by the introduction of 3-aminophenylboronic acid (APBA). The uniform morphology and composition analysis of the adsorbent (Fe₃O₄@CT-COOH-BA) were characterized by FT-IR, XRD, XPS, SEM, TEM and UV–visible spectroscopy. The adsorption capacity of as-prepared material was explored in detail by batch mode experiments. The adsorption kinetics fitted well with a pseudo-second order model, and the adsorption isotherms was well described by the Langmuir model with a maximum adsorption capacity of 23.8 mg g⁻¹ at 25 °C. Solution pH plays a crucial role in adsorption process and the optimized pH was 8.0. In addition, Fe₃O₄@CT-COOH-BA could be easily reused through an external magnet and the adsorption capacity reduced by only 4% after five adsorption–desorption cycles. These results prove that boric acid modified magnetic chitosan composite is an effective and practical adsorbent for specific recognition and selective adsorption of cis-diol-containing compounds.     

Membrane protein isolation by in situ solubilization, partitioning and affinity adsorption in aqueous two-phase systems. Purification of the human type 1 11beta-hydroxysteroid dehydrogenase

Recently developed aqueous two-phase systems based on non-ionic detergents and polymers are suitable for the separation of membrane proteins. Moreover, within this relatively membrane protein "friendly" environment, changes in temperature can be controlled and stabilizing agents may be added to ensure integrity of the target protein during isolation. Here, we use aqueous two-phase partitioning for the isolation of membrane bound 11beta-hydroxysteroid dehydrogenase type 1 (11beta-HSD1). Different detergents were used to find optimal conditions regarding solubilization and retaining target protein activity. We explored in situ solubilization by adding detergent directly to the aqueous two-phase system, as well as a batch metal affinity capture step of 6xHis tagged 11beta-HSD1 in the two-phase system. The use of detergent/polymer two-phase systems resulted in a specific enzyme activity of 3840 nmol mg(-1) min(-1) of the target membrane protein compared to a conventional purification protocol where a specific enzyme activity of 1440 nmol mg(-1) min(-1) was achieved.     

Characterization and evaluation of a macroporous adsorbent for possible use in the expanded bed adsorption of flavonoids from Ginkgo biloba L.

The suitability of the use of macroporous adsorbent Amberlite XAD7HP in expanded bed adsorption processes for the isolation of flavonoids from crude extracts of Ginkgo biloba L. has been assessed. The expansion and hydrodynamic properties of expanded beds were investigated and analyzed. The bed expansion as a function of operational fluid velocity was measured and correlated with the Richardson–Zaki equation. Theoretical predictions of the correlation parameters (the terminal settling velocity u_t and exponent n) were improved by modifying equations in the literature. Residence time distributions (RTDs) were studied using acetone as a tracer. Three measures of liquid phase dispersion (the height equivalent of theoretical plate, Bodenstein number and axial distribution coefficient) were investigated and compared to values previously obtained with commercial EBA adsorbents developed for protein purification. A suitable bed expansion ratio was found to be 1.25 times the settled bed height, which occurred at a corresponding flow velocity of 183 cm/h. For an initial settled bed height of 42 cm, the mean residence time of liquid in the expanded bed was around 28 min. Under these flow conditions, the axial mixing coefficient D_ax was 7.54 × 10⁻⁶ m²/s and the Bodenstein number was 28; the number of theoretical plates (N) was 19 and the height equivalent of a theoretical plate (HETP) was 2.77 cm. Rutin trihydrate was used as a model flavonoid for the characterization of the adsorption properties of Amberlite XAD7HP. Adsorption was observed to reach equilibrium within 3 h with 70% of the adsorption capacity being achieved within 30 min. The estimated maximum equilibrium adsorption capacity for rutin was estimated to be 43.0 mg/(g resin) when the results were fitted to Langmuir isotherms. The adsorption performance was not seriously impaired by the physical presence of G. biloba leaf powders. Assessment of the kinetics of the adsorption of rutin revealed that the rate constant for adsorption was only reduced by 15% in the presence of leaf powders at a concentration of 50 mg/mL. The results demonstrated that Amberlite XAD7HP should be suitable for expanded bed adsorption of flavonoids from crude extracts of G. biloba L.     

Correlation between excess adsorption data measured for solvent mixture/adsorbent systems and RM values obtained for different solutes chromatographed in binary mobile phases

This paper concerns the application of excess adsorption isotherms, measured for solvent mixture/adsorbent systems, to the characterization of TLC data. For this purpose the excess adsorption isotherms for three liquid mixtures: cyclohexane/ benzene, benzene/acetone, and carbon tetrachloride/ethyl acetate on silica gel at 20°C have been measured. These mixtures have been used as binary mobile phases in TLC measurements. It has been shown for a given solute in binary mobile phase that the quantity R_M is a simple function of the excess adsorption. Parameters of this function have been used to characterize chromatographic systems with binary mobile phases.