Detailed characterization of polycapillary focusing x-ray lenses by a charge-coupled device detector and a pinhole

A method to measure the detailed performance of polycapillary x-ray optics by a pinhole and charge coupled device (CCD) detector was proposed in this study. The pinhole was located between the x-ray source and the polycapillary x-ray optics to determine the illuminating region of the incident x-ray beam on the input side of the optics. The CCD detector placed downstream of the polycapillary x-ray optics ensured that the incident x-ray beam controlled by the pinhole irradiated a specific region of the input surface of the optics. The intensity of the output beam of the polycapillary x-ray optics was obtained from the far-field image of the output beam of the optics captured by CCD detector. As an application example, the focal spot size, gain in power density, transmission efficiency, and beam divergence of different parts of a polycapillary focusing x-ray lenses (PFXRL) were measured by a pinhole and CCD detector. Three pinholes with diameters of 500, 1000, and 2000 μm were used to adjust the diameter of the incident x-ray beam illuminating the PFXRL from 500 μm to the entire surface of the input side of the PFXRL. The focal spot size of the PFXRL, gain in power density, transmission efficiency, and beam divergence ranged from 27.1 μm to 34.6 μm, 400 to 3460, 26.70% to 5.38%, and 16.8 mrad to 84.86 mrad, respectively.     

Electromagnetic-field distribution measurements in the soft x-ray range: full characterization of a soft x-ray laser beam

We report direct measurement of the electromagnetic-field spatial distribution in a neonlike Ar capillary discharge-driven soft x-ray laser beam. The wave front was fully characterized in a single shot using a Shack-Hartmann diffractive optics sensor. The wave front was observed to be dependent on the discharge pressure and capillary length, as a result of beam refraction variations in the capillary plasma. The results predict approximately 70% of the laser beam energy can be focused into an area 4 times the size of the diffraction-limited spot, reaching intensities of approximately 4 x 10(13) W/cm(2).     

Focusing hard x rays to nanometer dimensions by adiabatically focusing lenses

We address the question of what is the smallest spot size that hard x rays can be focused to using refractive optics. A thick refractive x-ray lens is considered, whose aperture is gradually (adiabatically) adapted to the size of the beam as it converges to the focus. These adiabatically focusing lenses are shown to have a relatively large numerical aperture, focusing hard x rays down to a lateral size of 2 nm (FWHM), well below the theoretical limit for focusing with waveguides [C. Bergemann, Phys. Rev. Lett.912003204801].     

Upgrading design of the 3B1A beamline for x-ray nanometre lithography of microelectronic devices at BSRF

Beijing Synchrotron Radiation Facility is a partly dedicated synchrotron radiation source operated in either parasitic or dedicated mode. The 3B1A beamline, extracted from a bending magnet, was originally designed as a soft x-ray beamline for submicro x-ray lithography with critical lateral size just below 1μm in 1988 and no change has been made since it was built. But later the required resolution of x-ray lithography has changed from sub-micrometre to the nanometre in the critical lateral size. This beamline can longer more meet the requirement for x-ray nano lithography and has to be modified to fit the purpose. To upgrade the design of the 3B1A beamline for x-ray nano lithography, a mirror is used to reflect and scan the x-ray beam for the nano lithography station, but the mirror's grazing angle is changed to 27.9mrad in the vertical direction, and the convex curve needs to be modified to fit the change; the tiny change of mirror scanning angle is firstly considered to improve the uniformity of the x-ray spot on the wafer by controlling the convex curve.     

Optimal x-ray beam formation using a focusing mirror at the Langmuir synchrotron station

A beam focusing method is proposed for the Langmuir station of the Kurchatov synchrotron radiation source. This method can be implemented during experiments on recording the fluorescence yield intensity as a function of the angle between an incident beam and a sample surface. The x-ray beam is focused by a cylindrical mirror in such a way that the dimensions of the spot illuminated by the beam on a Langmuir film remain within the input angular aperture of an energy dispersive detector during scanning in the angle of incidence. The relationships for calculating the dimension of the illuminated spot in the scattering plane and the angular divergence of the focused x-ray beam are derived taking into account the dimension of the synchrotron radiation source and spherical aberration. Recommendations for optimizing station parameters and experimental conditions are presented.     

低噪音光折变体全息存储

光折变全息存储中,透过晶体的散射光会影响再现象的信噪比,本文基于两波耦合理论,对光折变存储中的散射噪音随光斑尺寸的变化作了简化计算和分析,结果表明减小辐照在晶体上的光斑尺寸能降低散射噪音,提高衍射效率和信噪比,采用球面参考波小光斑尺寸入射,在KNSBN光折变晶体中存储了傅里叶全息图,并得到了低噪音的再现象.     

Direct evidence of nanometric invasionlike grain boundary penetration in the A(1)/Ga system

We report the first in situ results of deformation during grain boundary penetration in the A(1)/Ga system, obtained with a novel, nondestructive hard x-ray synchrotron projection microscopy technique. Focusing the beam to a state-of-the-art spot size of 90 x 90 nm(2), we demonstrate that penetration is accompanied by continuous relative separation of the Al grains of the same final amplitude as the final Ga layer thickness in the absence of external stress. The formation of nanometric intergranular liquid layers is originated by a crack propagation process and inherently implies the presence of weak stress levels.     

Framework for three-dimensional coherent diffraction imaging by focused beam x-ray Bragg ptychography

We present the framework for convergent beam Bragg ptychography, and, using simulations, we demonstrate that nanocrystals can be ptychographically reconstructed from highly convergent x-ray Bragg diffraction. The ptychographic iterative engine is extended to three dimensions and shown to successfully reconstruct a simulated nanocrystal using overlapping raster scans with a defocused curved beam, the diameter of which matches the crystal size. This object reconstruction strategy can serve as the basis for coherent diffraction imaging experiments at coherent scanning nanoprobe x-ray sources.     

A crossed focused vortex beam with application to cold molecules

We report the generation of a crossed, focused, optical vortex beam by using a pair of hybrid holograms, which combine the vortex phase and lens phase onto a spatial light modulator. We study the intensity distributions of the vortex beam in free propagation space, and the relationship of its dark spot size with the incident Gaussian beam's waist, the lens's focal length, and its orbital angular momentum. Our results show that the crossed, focused, vortex beam's dark spot size can be as small as 16.3μm and adjustable by the quantum number of the orbital angular momentum, and can be used to increase the density of trapped molecules. Furthermore, we calculate the optical potential of the blue-detuned, crossed vortex beam for MgF molecules. It is applicable to cool and trap neutral molecules by intensity-gradient-induced Sisyphus cooling, as the intensity gradient of such vortex beam is extremely high near the focal point.     

Imaging and quality assessment of high-harmonic focal spots

We present a direct method of studying the focusability of an intense, short-pulse extreme-ultraviolet (XUV) beam obtained by high-harmonic generation. We perform near-field imaging of the focal spot of five high-harmonic orders strongly focused by a broadband toroidal mirror. To visualize the focal spot directly, we image the fluorescence induced by an XUV beam on a cerium-doped YAG crystal on a visible CCD camera. We can thus measure the harmonic spot size on a single image, together with the Strehl ratio, to evaluate the quality of focusing. Such techniques should become instrumental in optimizing the focusing conditions and reaching intensities required for exploring attosecond nonlinear optics in the XUV range.     

高能多脉冲辐射照相的复合靶物理分析

 介绍了电子束与钽靶相互作用的能量沉积解析理论和（钽-碳）复合靶的设计。单靶的某个区域内形成的高温等离子体沿轴的2个方向(±z)溅射而使单靶穿孔,大焦斑束形成较小的孔,小焦斑下靶孔较大而相对光滑。复合靶或修正复合靶可以经受2~3个束脉冲的连续照射。蒙卡模拟计算表明,复合靶或修正复合靶的焦斑尺寸与单靶相同,可用于多脉冲闪光照相。     

A focussing funnel for metastable helium

We have constructed a magneto-optical funnel for He atoms and studied its properties using a laser cooled, highly mono-energetic atomic beam. A simple model of its action allows us to quantitatively understand the observed spot size and “focal length”. We show that for a fast beam, the velocity damping coefficient plays an important role in determining the focal length of the device. The observed spot size is limited mainly by transverse heating processes which impose a transverse velocity spread. The device also permits easy scanning of the focussed spot. Received 30 October 1998 and Received in final form 27 January 1999     

The effect of spot size on linearity improvement of tetra-lateral position sensitive detector

Linearity improvement of tetra-lateral position sensitive detector (PSD) is highly desired in many applications where accurate measurements of the PSD are required. The effect of beam size on our newly proposed linearity improvement scheme is discussed in this paper. Theoretical studies on the electrical potential and collected photocurrents are presented to simplify the numerical calculation when the beam size of the spot is considered. Simulation results show that our new formula can still give a nearly perfect linearity and measurement accuracy even if the spot has a considerable beam size.     

K<Subscript><Emphasis Type="Italic">α</Emphasis></Subscript> x-ray emission characterization of 100 Hz, 15 mJ femtosecond laser system with high contrast ratio

We report K _α x-ray production with a high energy (110 mJ per pulse at 800 nm before compression/15 mJ at 400 nm after compression), high repetition rate (100 Hz), and high pulse contrast (better than 10⁻⁹ at 400 nm) laser system. To develop laser-based x-ray sources for biomedical imaging requires to use high-energy and high-power ultrafast laser system where compression is achieved under vacuum. Using this type of laser system, we demonstrate long-term stability of the x-ray yield, conversion efficiency higher than 1.5×10⁻⁵ with a Mo target, and the x-ray spot size close to the optical focal spot. This high-repetition K _α x-ray source can be very useful for x-ray phase-contrast imaging. S. Fourmaux and C. Serbanescu contributed equally to this work.     

Laue弯晶聚焦特性的光线追迹研究

由于可有效降低高热负载的影响, Laue弯晶是插入件辐射高通量密度硬X射线(30 keV以上)聚焦、 准直和单色化的最有效的光学元件.研究其聚焦光学特性,对发展高性能、高稳定的Laue弯晶单色器具有重要意义. 采用自行发展的光线追迹软件较为系统地研究了Laue弯晶的聚焦特性, 分析了入射光性质及弯晶参数对聚焦光斑、焦距、发散度等主要光学参数的影响. 结果表明,衍射能量越高,聚焦光斑越小,并趋于稳定值;弯曲半径越小,聚焦光斑越小, 并在其达到一阈值时得到聚焦光斑的极小值,之后随着弯曲半径的变小,由于像差等因素的影响, 聚焦光斑反而变大;晶体越厚,聚焦光斑越大,呈线性正比关系.对于衍射光发散度, 其随着衍射能量的增大而变小,并趋于稳定值;其与晶体曲率呈线性正比关系. 同时通过研究得到弯晶各参数的合理选择范围.     

Modified hollow Gaussian beam and its paraxial propagation

A model named modified hollow Gaussian beam (HGB) is proposed to describe a dark hollow beam with adjustable beam spot size, central dark size and darkness factor. In this modified model, both the beam spot size and the central dark size will be convergent to finite constants as the beam order approaches infinity, which are much different from that of the previous unmodified model, where the beam spot size and the central dark size will not be convergent as the beam order approaches infinity. The dependences of the propagation factor of modified and unmodified HGBs on the beam order are found to be the same. Based on the Collins integral, analytical formulas for the modified HGB propagating through aligned and misaligned optical system are derived. Some numerical examples are given.     

Synthesis of silver nanoparticles by laser ablation in pure water

We have successfully produced silver nanoparticles by irradiating an Ag target with a 532-nm laser beam in pure water. By working with high laser power and small spot sizes, we were able to synthesize very small spherical particles with a typical size of 2–5 nm. The influence of the beam spot size, the laser power, and the ablation time were studied, and the possible mechanisms of particle formation are discussed. PACS 79.20.Ds; 81.07.-b     

一种CCD辅助测量基模(TEM00)激光光斑尺寸的方法

激光光束是一种振幅和等相位面都在变化的高斯球面光波,其最小光斑的位置和大小不易确定,本文在实践的基础上提出一种测量基模(TEM₀₀)激光光斑尺寸的方法,解决了这一问题.     

基于泰伯效应的高斯光束尺寸测量

光栅用在高斯光束参数测量中的突出优点是方法简单，成本较低，全息光栅由于其制备容易，无周期误差而比一般光栅具有更多的优点。在用光栅进行光斑测量的实验中，观察到由全息光栅引起的泰伯（Ｔａｌｂｏｔ）效应携带有关光斑参数的有用信息，本文提出了一种基于泰伯效应的测量方法，只需测定条纹间隔就能确定高斯光束尺寸，因此降低了对光源或光栅定位精度，电路和光源稳定性的要求，文中聚焦高斯光束照明全息光栅时光场分布，及其     

Non-paraxial Elliptical Gaussian Beam

By using the methods of Hertz vector and angular spectrum transormation, the exact solution of non-paraxial elliptical Gaussion beam with general astigmatism based on Maxwell′s equations is obtained. We discussed its propagation characteristics. The results show that the orientation of the elliptical beam spot changes continuously as the beam propagates through isotropic media. Splitting or coupling of beam spots may occur for different initial spot size. This is very different from that of paraxial elliptical Gaussian beam.