含二烯丙基双酚A醚相容剂对HDPE/PC共混体系的影响

用低密度聚乙烯接枝二烯丙基双酚Ａ醚（ＬＤＰＥ ｇ ＤＢＡＥ）作为高密度聚乙烯／聚碳酸酯（ＨＤＰＥ／ＰＣ）共混体系的增容剂,研究了其对ＨＤＰＥ／ＰＣ共混体系的影响．通过共混物形态观察、热力学性能测试和结晶性分析,发现ＬＤＰＥ ｇ ＤＢＡＥ对ＨＤＰＥ／ＰＣ共混体系有良好的增容效果．并发现了增容剂在共混物中的最佳用量为１０ｐｈｒ,提高增容剂的接枝率更有利于改善共混物的性能     

EVA增容PP/HDPE共混体系的形态结构与性能

采用乙烯－醋酸乙烯酯共聚物（ＥＶＡ）作为聚丙烯（ＰＰ）／高密度聚乙烯（ＨＤＰＥ）共混体系的增容剂,通过冲击实验、拉伸实验、示差量热扫描仪（ＤＳＣ）和扫描电镜（ＳＥＭ）,系统地研究了共混体系的性能与其形态结构之间的。结果表明,ＥＶＡ是ＰＰ／ＨＤＰＥ共混物较好物增容剂,ＥＶＡ可以使ＰＰ、ＨＤＰＥ的晶相结构受到一定程度的破坏,增加ＰＰ和ＨＤＰＥ的相容性,同时共混物的冲击韧性明显提高。     

POM／EVA共混物的研究

用力学测试、扫描电镜（ＳＥＭ）、热分析（ＤＳＣ）等手段研究了聚甲醛（ＰＯＭ）与乙烯－醋酸乙烯酯共聚物（ＥＶＡ）共混物（ＰＯＭ／ＥＶＡ）的力学性能及其微同形态；用聚甲醛与马来酸二丁酯（ＤＢＭ）的接枝物（ＰＯＭ－ｇ－ＤＢＭ）作相溶剂，能改变共的两相间的粘结力，从而提出了共混物的力学性能，ＳＥＭ观察表明接枝物的加入改变了ＰＯＭ／ＥＶＡ共混物的断裂方式，微观形态及结晶性能，对其热性能影响不大；通过改变ＰＯ     

聚二甲基硅氧烷／聚氨酯共混体系的增容作用（I）

采用二甲基硅氧烷－ｂ－乙二醇嵌段共聚物（ＤＭＳ－ｂ－ＯＥ）对聚二甲基硅氧烷／聚氨酯（ＰＤＭＳ／ＰＵ）共混体系的增容，重点研究了增容共混体系的微观形态结构和软科学性能之间的关系。扫描电子显微镜、动态力学分析和力学性能测试结果表明：ＤＭＳ－ｂ－ＯＥ对ＰＤＭＳ／ＰＵ具有优良的增容作用，改善了ＰＤＭＳ／ＰＵ共混体系的相容性，提高了该共混物的力学性能。其抗张强度由３．４ＭＰａ提高到７．６ＭＰａ。     

尼龙1010分别与未接枝和接枝马来酸酐的高抗冲聚苯乙烯的共混体系研究

研究了尼龙１０１０（ Ｐ Ａ１０１０） 与高抗冲聚苯乙烯（ Ｈ Ｉ Ｐ Ｓ） 及马来酸酐官能化的 Ｈ Ｉ Ｐ Ｓ（ Ｈ Ｉ Ｐ Ｓ ｇ Ｍ Ａ） 间的相互作用,利用 Ｄ Ｓ Ｃ, Ｄ Ｍ Ａ, Ｓ Ｅ Ｍ 及拉伸测试等方法研究了不同组成比的共混物 Ｐ Ａ１０１０／ Ｈ Ｉ Ｐ Ｓ 与 Ｐ Ａ１０１０／ Ｈ Ｉ Ｐ Ｓ ｇ Ｍ Ａ 的结晶、玻璃化转变、形态及力学性能．结果表明 Ｈ Ｉ Ｐ Ｓ 与 Ｐ Ａ１０１０ 虽然结构相差甚远,但两者之间仍存在着一定的相互作用;而 Ｈ Ｉ Ｐ Ｓ ｇ Ｍ Ａ 可使 Ｐ Ａ１０１０ 的低温熔融峰变小,当 Ｈ Ｉ Ｐ Ｓ ｇ Ｍ Ａ 的含量≤５０ ％ 时,随着其含量的增加,共混物中 Ｐ Ａ１０１０ 的结晶温度升高;当含量＞ ５０ ％ 时, Ｐ Ａ１０１０ 发生分级结晶行为,其结晶温度由原来的１７８ ℃降至８３ ℃,同时 Ｈ Ｉ Ｐ Ｓ ｇ Ｍ Ａ 与 Ｐ Ａ１０１０ 间的相互作用变大, Ｄ Ｍ Ａ 谱上有明显的新的松驰峰． Ｐ Ａ１０１０／ Ｈ Ｉ Ｐ Ｓ ｇ Ｍ Ａ 共混体系的拉伸性能要优于相同组成的 Ｐ Ａ１０１０／ Ｈ Ｉ Ｐ Ｓ 体系．以上现象主要是由于 Ｈ Ｉ Ｐ Ｓ ｇ Ｍ Ａ 与 Ｐ Ａ１０１０ 中的端胺基发生了化学反应,产生了接枝共聚物 Ｐ Ａ１０１０ ｇ Ｈ Ｉ Ｐ     

聚酰胺1010／聚乙烯－马来酸酐接枝共聚物共混物力学和热学性能研究

为了表明马来酸酐接枝聚烯烃后对聚酰胺的相容作用，本文研究了聚酰胺１０１０（ＰＡ１０１０）／聚乙烯－马来酸酐接枝共聚物（ＰＥ－ｇ－ＭＡＨ）共混物在不同ＭＡＨ接枝量下的结晶性与力学性能。研究表明，ＭＡＨ的存在导致ＰＥ－ｇ－ＭＡＨ－ｃｏ－ＰＡ１０１０共聚物的形成，而该共聚物在标题共混物中起着相容剂的作用。共混物的结晶性能变化显示了共混组分间存在一定程度的混溶性。在一定的ＭＡＨ含量内，标题共混物具有协同效应。     

高密度聚乙烯与乙烯丙烯辛烯—1共聚物共混体系的相容性

用ＤＳＣ和ＷＡＸＤ方法研究了高密度聚乙烯／聚（乙烯丙烯辛烯－１）（ＨＤＰＥ／ＥＰＯ）共混体系的结晶性能。共混物的ＤＳＣ曲线皆呈单峰，表明共混体系形成了共晶。晶胞参数ａ及结晶度随共混物组成而变，进一步证明ＨＤＰＥ／ＥＰＯ共混体系的相容性。     

高密度聚乙烯与乙烯丙烯辛烯－1共聚物共混体系的相容性

用ＤＳＣ和ＷＡＸＤ方法研究了高密度聚乙烯／聚（乙烯丙烯辛烯－１）（ＨＤＰＥ／ＥＰＯ）共混体系的结晶性能。共混物的ＤＳＣ曲线皆呈单峰，表明共混体系形成了共晶。晶胞参数ａ及结晶度随共混物组成而变，进一步证明ＨＤＰＥ／ＥＰＯ共混体系的相容性．     

尼龙6/多单体接枝聚丙烯共混物的形态结构及力学性能的研究

用多组分熔融接枝的方法将甲基丙烯酸缩水甘油酯（ Ｇ Ｍ Ａ） 和苯乙烯（ Ｓｔ） 共同接枝于聚丙烯（ Ｐ Ｐ） 上,制得多单体接枝聚丙烯 Ｐ Ｐ ｇ （ Ｇ Ｍ Ａ ｃｏ Ｓｔ） ．该接枝物具有高的 Ｇ Ｍ Ａ 接枝率．本研究利用 Ｆ Ｔ Ｉ Ｒ、 Ｓ Ｅ Ｍ、 Ｔ Ｅ Ｍ、 Ｄ Ｓ Ｃ 和力学性能测试等分析方法,研究了多组分熔融接枝聚丙烯（ Ｐ Ｐ ｇ （ Ｇ Ｍ Ａ ｃｏ Ｓｔ）） 对尼龙６／ Ｐ Ｐ 共混物的形态结构, Ｔｇ 和力学性能的影响．结果表明, Ｐ Ｐ ｇ （ Ｇ Ｍ Ａ ｃｏ Ｓｔ） 中的环氧基团与尼龙６（ Ｐ Ａ６） 末端的胺基发生化学反应,原位形成的 Ｐ Ｐ Ｐ Ａ６ 共聚物能有效的改善 Ｐ Ａ６ 与 Ｐ Ｐ 的相容性,可以使 Ｐ Ｐ 均匀的分散在 Ｐ Ａ６ 基体中,相区尺寸明显减小,提高了拉伸强度．由于两相的相容性较好,从而共混物的 Ｔｇ 有明显的变化．此外,通过透射电镜观察,发现 Ｐ Ａ６／ Ｐ Ｐ ｇ （ Ｇ Ｍ Ａ ｃｏ Ｓｔ）（７０／３０） 合金中存在着特殊的微相分离结构．     

PES／PC共混体系的相容性与力学性能

ＰＥＳ／ＰＣ共混体系的相容性与力学性能姜振华，马荣堂，寇喜春，安立佳（吉林大学化学系长春）（中国科学院长春应用化学研究所长春１３００２２）关键词聚醚砜，聚碳酸酯，共混物，力学性能聚醚砜（ＰＥＳ）是一种性能优异的特种工程塑料，它具有强度高、刚性大、耐热...     

ABS的MAH/St多单体熔融接枝及其对PA6/ABS共混体系相形态和力学性能的影响

通过多单体熔融接枝的方法制备出了具有较高接枝率的ABS接枝物 (ABS g (MAH co St) ) ,并对其接枝机理进行了初步探讨 .研究表明 ,MAH、St接枝ABS时 ,反应主要发生在ABS中聚丁二烯的双键部位 .同时 ,当MAH与St的用量比约为 1:1时接枝率达到最高 .ABS g (MAH co St)作为尼龙 6 (PA6 ) ABS共混体系相容剂起到了良好的增容效果 .实验证明 ,相容剂使用前后 ,共混物的相区尺寸由几十 μm减小到 1μm以下 ,且分布更加均匀 ;共混物的拉伸强度和冲击强度等力学性能也同时得到均衡改善 .     

PC/ABS blends: Compatibilization and mechanical behaviour

PC/ABS(M) blends, encompassing the whole composition range between pure PC and ABS(M), were prepared by melt-mixing in a Brabender-like apparatus. Thermal, mechanical and impact tests were performed on compression moulded specimens. Inward Tg shifts were detected for PC and ABS(M) in the blends with respect to pure PC and ABS(M) values, indicating an interaction between the component domains. This finding was confirmed by the comparison of the experimental tensile moduli with the Kernels model predictions, showing an evidence of a good adhesion between the phases. A synergistic effect was observed for the impact strength as well as for the maximum stress at an ABS(M) blend content of about 25 weight %. All the results are interpreted on the basis of an interlayer existing at the boundary between the PC and ABS phases. A preliminary investigation on the influence of the ABS internal composition, keeping constant all the other conditions (mixing, processing, specimen preparation), was carried out as well. Differences in the properties of PC/ABS(M) and PC/ABS(B) blends are thoroughly discussed. The compatibility between PC and ABS domains seems to be scarcely influenced by such a parameter in these blends.     

PC及PC/ABS共混物的疲劳裂纹扩展研究

研究了聚碳酸酯(PC)和PC/ABS高分子材料的疲劳裂纹扩展规律,利用改进柔度法测量其裂纹扩展速率,采用扫描电子显微镜(SEM)观察其断口形貌,分析疲劳裂纹扩展机理.在较大裂纹扩展速率(10-6～10-3mm/cycle)范围内,PC/ABS的疲劳裂纹扩展速率可以用Paris公式da/dN=9·5587×10-5(ΔK)2·88381来描述.高分子材料PC的疲劳裂纹扩展速率约为高分子材料PC/ABS的3倍.高分子材料PC/ABS疲劳裂纹面上的特征以韧窝为主,较低裂纹扩展速率对应较小的韧窝,较高裂纹扩展速率对应较大的韧窝.高分子材料PC疲劳裂纹面有明显的不连续裂纹扩展带,其裂纹面相对较平.     

Effect of cyclic loading on tensile properties of PC and PC/ABS

The effects of cyclic loading on tensile fracture properties of polycarbonate (PC) and the alloy of polycarbonate and acrylonitrile-butadiene-styrene (PC/ABS) are experimentally investigated in the paper. Two digital cameras are used to record simultaneously the tensile deformation of specimens and the large deformation and the necking process of these polymers are discussed. Two lateral contractions are not identical at the later tensile stages and the contraction ratios in each lateral direction are related with the tensile strains in axial direction on width and thickness surface. The curvature radiuses at the minimum section during necking process are shown. The volume increases during necking process and then decreases gradually. The yield stress and fracture stress of PC/ABS are lower than that of PC. The degradation of the fracture stress and fracture strain due to the application of cyclic loading is larger for PC than that for PC/ABS, and these can be used to explain qualitatively why PC has higher fatigue crack growth rate than PC/ABS.     

Thermal and structural analysis of ultrasonic-welded PC/ABS blend for automobile applications

PC/ABS thermoplastic blends are widely employed in manufacturing sectors, as it yields good mechanical behavior when subjected to dynamic loading conditions. While investigating the fundamental nature of PC/ABS blends, ultrasonic welding process appears to suit their joining as compared to other conventional techniques. This paper focuses on PC/ABS welding using ultrasonic and the subsequent investigation from the insight of thermal science. It is imperative for the materials to retain key properties after subjecting it to welding. Examinations to evaluate these properties through DSC reveal a lower onset temperature change and a small variation of glass transition temperature, respectively, for parts which indicate minimal changes in thermal properties in welded and non-welded specimens. Apparent activation energies determined from TG data are practically independent of heating rates, which suggests that the most important process in the degradation of these materials corresponds to ABS. Those mixtures with high PC content show a clear increase in apparent activation energies with heating rate, suggesting that the thermal degradation mechanism of these samples is composed of several complex processes, each predominant during different stages of the overall process. SEM is used to investigate the structural morphology of the welded parts.     

异山梨醇型聚碳酸酯与ABS树脂共混体系的结构与性能研究

采用异山梨醇型聚碳酸酯(DB),与掺混型ABS熔融共混制备了具有不同聚丁二烯(PB)含量和丙烯腈(AN)含量的DB/掺混型ABS合金,并在考察掺混型ABS特征对合金结构与性能的影响的基础上,分别使用同种掺混型ABS以及各种商品化ABS树脂,比较了DB/ABS合金和双酚A型聚碳酸酯/ABS合金的性能及其变化规律.结果表明,对DB/掺混型ABS(70/30)合金而言,PB含量变化对于合金拉伸性能的影响明显大于AN含量变化所带来的影响,在PB含量为6.3 wt%条件下,各不同AN含量的合金体系均有最好的性能表现.PB含量和AN含量变化对合金分散相形态的影响与力学拉伸性能变化特征一致.DB/ABS合金体系均具有良好的热稳定性与热力学相容性,受AN含量和PB含量变化的影响较小,合金玻璃化转变温度与DB非常接近.以双酚A型聚碳酸酯为基础的聚碳酸酯(PC)/ABS合金及以异山梨醇型聚碳酸酯为基础的DB/ABS合金,在拉伸性能变化上均表现出完全相同的规律,且无论是采用掺混型ABS还是采用商品化ABS的体系,PC/ABS与DB/ABS合金在拉伸性能所反映出的规律也是基本一致的.     

STUDIES ON FLAME-RETARDANT PC/ABS MULTIPLE-ELEMENT ALLOY

The preparation technology of flame-retardant PC/ABS alloys was studied in this paper. Using a high-efficiencyflame retardant system and by means of multiple-ingredient compatibilizing, PC/ABS alloys with excellent impact strengthand flame retardant property were prepared. The experimental results showed that by using PS-g-MAH and SMA assynergistic compatibilizers, the notched Izod impact strength and flammability of PC/ABS alloy obtained in the present work can be up to 175 J/m and UL-94 V0, respectively.     

Experimental investigation and modeling of the mechanical behavior of PC/ABS during monotonic and cyclic loading

The purpose of this work is to characterize the mechanical behavior of blends of polycarbonate (PC) and acrylonitrile-butadiene-styrene (ABS) during monotonic and cyclic loading. Compression experiments were performed using a SHIMADZU universal testing machine (10⁻⁴ to 10⁻² s⁻¹) and a split Hopkinson pressure bar (1600–5000 s⁻¹), with, the test temperatures ranging from 293 to 353 K. The influence of the rate and temperature on the deformation of PC/ABS is discussed in detail. Based on the investigation of numerous constitutive models, a phenomenological model called DSGZ was chosen to describe the compression behavior of PC/ABS. This model could not accurately reproduce the deformation of polymers at high strain rates when utilizing the same material coefficients for the low and high strain–rate deformations. In addition, this model was unable to capture the deformation features during unloading and subsequent reloading when adopting the original stress–strain updating algorithm. Hence, some improvements to the model have been implemented to better predict the deformation. Finally, the model predictions are shown to be consistent with the experimental results.     

酸碱处理蒙脱土与磷酸酯阻燃剂复配阻燃PC/ABS合金

采用酸碱处理法对蒙脱土进行有机化改性, 再将酸碱处理的蒙脱土与磷酸酯阻燃剂复配, 作为聚碳酸酯/丙烯腈-丁二烯-苯乙烯三元共聚物(PC/ABS)合金的阻燃体系, 并表征了酸碱处理蒙脱土对合金的热稳定性和阻燃性能. 结果表明, 间苯二酚双(二苯基磷酸酯)改性的蒙脱土(BDP-MMT)使阻燃PC/ABS合金的起始分解温度降低, 而酸碱处理蒙脱土却使合金的起始分解温度有所提高; BDP-MMT的加入会恶化碳层的阻隔性能, 而酸碱处理蒙脱土却可以增加碳层的稳定性, 使第二热释放峰值出现的时间延迟, 且适合的酸浓度处理蒙脱土可以使合金通过UL-94 V-0级检验.     

Morphology and thermal properties of a PC/PE blend with reactive compatibilization

Reactive compatibilization of immiscible polymers is becoming increasingly important and hence a representative study of a polycarbonate/high density polyethylene (PC/HDPE) system is the focus of this paper. A grafted copolymer PC‐graft‐ethylene‐co‐acrylic acid (PC‐graft‐EAA) was generated as a compatibilizer in situ during processing operation by ester and acid reaction between PC and ethylene‐acrylic acid (EAA) in the presence of the catalyst dibutyl tin oxide (DBTO). As the polyethylene (PE) matrix does not play any part during the synthesis of the copolymer and since PC and EAA are also immiscible, to simplify the system, the influence of this copolymer formation at the interface between PC and EAA on rheological properties, phase morphology, and crystallization behavior for EAA/PC binary blends was first studied. The equilibrium torque increased with the DBTO content increasing in EAA/PC blends on Haake torque rheometer, indicating the in situ formation of the graft copolymer. Scanning electron microscopy (SEM) studies of cryogenically fractured surfaces showed a significant change at the distribution and dispersion of the dispersed phase in the presence of DBTO, compared with the EAA/PC blend without the catalyst. Differential scanning calorimetry (DSC) studies suggested that the heat of fusion of the EAA phase in PC/EAA blends with or without DBTO reduced with the formation of the copolymer compared with pure EAA. Then morphological studies and crystallization behavior of the uncompatibilized and compatibilized blends of PC/PE were studied as functions of EAA phase concentration and DBTO content. Morphological observations in PC/PE blends also revealed that on increasing the EAA content or adding the catalyst DBTO, the number of microvoids was reduced and the interface was intensive as compared to the uncompatibilized PC/PE blends. Crystallization studies indicated that PE crystallized at its bulk crystallization temperature. The degree of crystallinity of PE phase in PC/PE/EAA blends was also reduced with the addition of EAA and DBTO compared to the uncompatibilized blends of PC/PE, indicating the decrease in the degree of crystallinity was more in the presence of PC‐graft‐EAA. Copyright © 2007 John Wiley & Sons, Ltd.