Electrical properties of pulsed laser-deposited SrxBiyTa2O9 thin films on Bi/Sr ratios

The dependence of the electrical properties of Sr_xBi_yTa₂O₉ thin films on the (Bi/Sr ratio 1.6, 2.3, 2.8, 3.4) has been investigated. The Sr_xBi_yTa₂O₉ ferroelectric thin films were synthesized on Pt/Ti/SiO₂/Si substrates using the pulsed laser deposition method. Saturation polarization (P_st) and coercive field (2E_c) depend on the Bi/Sr ratio. P_st increases while E_c decreases with an increase in Bi/Sr ratio. Atomic Force Microscopy images show that the grain size grows with increasing Bi/Sr ratio. It is observed that the impedance behavior in Sr_xBi_yTa₂O₉ thin film, conforms to the Constant Phase Element (CPE) model. It is believed that the diffuse charges at the grain boundary build up a surface polarization because the impedance behavior close to pure capacitor with grain size increased.     

Ferroelectric properties of Pr and Nb co-substituted Sr0.8Bi2.2Ta2O9 thin films

Thin film of both A- and B-site co-substituted Sr_0.8Bi_2.2Ta₂O₉ (SBT) by Pr³⁺ and Nb⁵⁺, i.e. Sr_0.8Pr_0.1Bi_2.1Ta_1.5Nb_0.5O₉ (SPBTN) was fabricated on Pt/Ti/SiO₂/Si substrates by metalorganic decomposition method. The Nb⁵⁺ substitution at B-site and Pr³⁺ substitution at A-site enhanced the remanent polarization and reduced the coercive field of the films, respectively. The remanent polarization (2P_r) value of the SPBTN film was 22 μC/cm². The coercive field (2E_c) value of the SPBTN film was 102 kV/cm, which was much lower than that of SBTN (165 kV/cm). The effects of substitution on structural and ferroelectric properties of SBT were discussed in detail. As a result, the A- and B-sites co-substitution may be one of the promising ways to improve ferroelectric properties of SBT.     

Ti deficiency effect on the dielectric response of CaCu3Ti4O12 ceramics

Single phase ceramics CaCu₃Ti_4.0O₁₂ and CaCu₃Ti_3.9O₁₂ have been prepared using the traditional solid-state reaction method. Compared with the stoichiometric ceramics CaCu₃Ti_4.0O₁₂, Ti-deficient ceramics CaCu₃Ti_3.9O₁₂ have the larger lattice parameter, the higher force constant, and smaller dielectric constant and the lower dissipation factor, although their fundamental characters of dielectric response are similar. Their characteristic relaxation frequencies are not well fitted with the Arrhenius Law but a tentatively supposed relation. With the Cole-Cole Law, the fitted broadened factors of dissipation peaks are 0.5433 and 0.8651 for CaCu₃Ti_3.9O₁₂ and CaCu₃Ti_4.0O₁₂, respectively. All facts mentioned above imply that mutually correlated motion of Ti ions or defects may be expected to be responsible for the giant dielectric constant and high dissipation factor of CaCu₃Ti_4.0O₁₂.     

Observation of giant dielectric constant in CdCu3Ti4O12 ceramics

Although CdCu₃Ti₄O₁₂ is isostructural to CaCu₃Ti₄O₁₂, the room temperature low-frequency dielectric constant of the former compound was reported to be ∼400, only 1/25 of that of the latter material [M.A. Subramanian, et al., J. Solid State Chem. 151 (2000) 323]. In this communication, we report that the dielectric constant of CdCu₃Ti₄O₁₂ can be remarkably increased by elevating the sintering temperature. The room temperature dielectric constant at 100 kHz achieves 9000, almost as much as that of CaCu₃Ti₄O₁₂, for the sample sintered at 1283 K. The appearance of giant dielectric constant in CdCu₃Ti₄O₁₂ is explained in terms of internal barrier layer capacitance (IBLC) effect with the subgrain boundary as the barrier. Our result supplies an approach in searching for new giant-dielectric-constant materials in the CaCu₃Ti₄O₁₂ family.     

Relaxor behavior of K0.5La0.5Bi2Ta2O9 ceramics

Potassium lanthanum bismuth tantalate (K_0.5La_0.5Bi₂Ta₂O₉), a new relaxor ferroelectric was synthesized via the solid-state reaction route. X-ray structural studies along with Rietveld refinement confirmed it to be an n=2 member of the Aurivillius family of oxides and the refined lattice parameters are , and . The appearance of 1/2{h00} and 1/2{hk0} type superlattice reflections in the electron diffraction patterns reflected the presence of ordered polar regions. A broad dielectric peak associated with frequency dependent dielectric maximum temperature was observed. The value of the diffuseness parameter γ=1.93, obtained from the fit of a modified Curie-Weiss law established the relaxor nature of the title compound. The dielectric relaxation obeyed the Vogel-Fulcher relation wherein and . The relaxor behavior was attributed to the local polar ordering on A-sites.     

Bismuth zinc niobate (Bi1.5ZnNb1.5O7) ceramics derived from metallo-organic decomposition precursor solution

The preparation, microstructure development and dielectric properties of Bi_1.5ZnNb_1.5O₇ pyrochlore ceramics by metallo-organic decomposition (MOD) route are reported. Homogeneous precalcined ceramic powders of 13-36 nm crystallite size were obtained at temperatures ranging from 500 to 700 °C. The thermal decomposition/oxidation of the gelled precursor solution was chemically analyzed, TG/DTA, XRD, and SEM, led to the formation of a pure cubic pyrochlore phase with a stoichiometry close to Bi_1.5ZnNb_1.5O₇ which begins to form at 500 °C. The metallo-organic precursor synthesis method, where Bi, Zn and Nb ions are chelated to form metal complexes, allows the control of Bi/Zn/Nb stoichiometric ratio on a molecular scale leading to the rapid formation of bismuth zinc niobate (Bi_1.5ZnNb_1.5O₇) ceramic fine powders with pure pyrochlore structure. The powders were pressed into pellets and can be sintered at temperatures as low as 800-1000 °C. Fine crystalline ceramics with the grain size in the range of 200-500 nm have been obtained at the sintering temperature of 800 °C. The dielectric properties in high frequency to microwave range were measured and discussed.     

Investigations of structural, dielectric and ferroelectric behavior of europium substituted SrBi2Ta2O9 ferroelectric ceramics

Europium substituted samples of the compositions Sr_1−xEu_xBi₂Ta₂O₉ (x=0.0,0.025,0.050,0.10 and 0.20) were synthesized by solid state reaction method and studied for their structural, dielectric and ferroelectric properties. The X-ray diffractograms confirmed the formation of single phase layered perovskite structure in all the samples. The temperature variation of dielectric constant shows that the Curie temperature (T_c) decreases on increasing concentration of europium. The dielectric loss reduces significantly with europium addition. The P-E studies of the Eu-substituted SBT ceramics show that the remanent polarization increases with increasing concentration of europium.     

Maxwell-Wagner characterization of dielectric relaxation in Ni0.8Zn0.2Fe2O4/Sr0.5Ba0.5Nb2O6 composite

Dense composites were prepared through incorporating the dispersed Ni_0.8Zn_0.2Fe₂O₄ ferromagnetic particles into Sr_0.5Ba_0.5Nb₂O₆ ferroelectric matrix. Extrinsic dielectric relaxation and associated high permittivities of the materials are reported in the composites. We used an ideal equivalent circuit to explain electrical responses in impedance formalism. A Debye-like relaxation in the permittivity formalism was also found. Interestingly, real permittivity (ε′) of the sample containing 30% Ni_0.8Zn_0.2Fe₂O₄ shows obvious independence of the temperature at 100 kHz. Dielectric relaxation and high-ε′ properties of the composites are explained in terms of the Maxwell-Wagner (MW) polarization model.     

Relaxor Behaviour and Ferroelectric Properties of （Li0.12Na0.88） （Nb0.9-xWa0.10Sbx）O3 Lead-Free Ceramics

New lead-free ceramics （Lio.12Na0.88） （Nbo.9-x Ta0.10 Sbx） 03 （0.01 × 0.06） are synthesized by solid-state reaction method. The dielectric, piezoelectric and ferroelectric properties of the ceramics are studied. The dielectric constant dependence with temperature and frequency of the ceramic specimen with x = 0.04 shows typical characteristics of relaxor ferroelectrics, and the Vogel-Fulcher relationship is fulfilled. The dielectric behaviour and its relation to the phase transition phenomena are discussed. The polarization hysteresis loops at room temperature are also measured.     

Ferroelectric-relaxor behavior of (Na0.5K0.5)NbO3-based ceramics

We report that ferroelectric-relaxor behavior is induced by doping of SrO and TiO₂, or BaO and TiO₂ into classic ferroelectric (Na_0.5K_0.5)NbO₃. It is found that [(Na_0.5K_0.5)_0.9Sr_0.1](Nb_0.9Ti_0.1)O₃ ceramics exhibit a pronounced ferroelectric-relaxor behavior, comparable to that of [(Na_0.5K_0.5)_0.9Ba_0.1](Nb_0.9Ti_0.1)O₃ ceramics. Our results indicate that the relaxor behavior is closely related to the appearance of micropolar regions in these systems. The relaxor behavior should arise from the dynamic response of micropolar clusters. Raman spectra of [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ ceramics measured in the wavenumber range from 100 to 1200 cm⁻¹ confirm that the first order scattering is dominant in phonon bands should result from both short-range ordered region (micropolar regions) and disordered matrix. The frequency dependence of dielectric permittivity measurements show that the relaxor behavior of SrO and TiO₂, or BaO and TiO₂ doped (Na_0.5K_0.5)NbO₃ ceramics is not a Debye type in the radio frequency range.     

Dielectric relaxations in Tb0.91Yb1.38Bi0.71Fe5O12 ceramics

Dielectric relaxations of Tb_0.91Yb_1.38Bi_0.71Fe₅O₁₂ ceramics were investigated. A Debye-type relaxation was observed in the temperature range of 125-620 K with an activation energy of 0.29 eV. This activation energy agreed well with that of carriers hopping between Fe²⁺ and Fe³⁺, indicating that this relaxation might be a dipolar-type relaxation associated with the hopping carries. A high relaxorlike dielectric peak with a very strong frequency dispersion in the high temperature range of 400-620 K might be originate from the oxygen vacancies related dielectric relaxation.     

Dielectric-spectroscopic and a.c. conductivity investigations on copper doped layered Na1.8K0.2Ti3O7 ceramics

Dielectric studies on copper doped derivatives of polycrystalline layered mixed alkali trititanate Na_1.8K_0.2Ti₃O₇ ceramics indicate that the losses are of mixed type and decrease on copper doping. However, the temperature dependent permittivity plots are characteristic of the diffuse nature of a possible ferroelectric phase transition and hence give indication of relaxor ferroelectric behaviour. From the EPR spectra, recorded at room temperature, it can be seen that the substitution of copper occurs at Ti⁴⁺ as preferred site with a divalent oxidation state (Cu²⁺) for all compositions. Also, copper doping enhances the transition temperature, which is indicative of the stabilization of the existing ferroelectric phase up higher temperatures. Besides bolstering electron hopping conduction, acceptor doping restrains the interlayer ionic conduction. Moreover, electron hopping (polaron) conduction is dominant over the lower temperature region, while interlayer ionic conduction prevails in the higher temperature region.     

Dielectric properties of SrBi2−xPrxNb2O9 ceramics (x=0, 0.04 and 0.2)

SrBi_2−xPr_xNb₂O₉ (x=0, 0.04 and 0.2) ceramics were prepared by a solid state reaction method. X-ray diffraction analysis indicated that single-phase layered perovskite structure ferroelectrics were obtained. A relaxor behavior of frequency dispersion was observed among Pr-doped SrBi₂Nb₂O₉. The degree of frequency dispersion ΔT increased from 0 for x=0-7 °C for x=0.2, and the extent of relaxor behavior γ increased from 0.94 for x=0-1.45 for x=0.2. The substitution of Pr ions for Bi³⁺ ions in the Bi₂O₂ layers resulted in a shift of the Curie point to lower temperatures and a decrease in remanent polarization. In addition, the coercive field 2E_c reduced from 110 kV/cm for an undoped specimen to 90 kV/cm for x=0.2.     

Dielectric and Ferroelectric Properties of La-Doped SrBi2Nb2O9 Ceramics

Sr1-xLa2x/3Bi2Nb20O （0 ≤ x ≤0.2） ceramic samples are prepared by the solid-state reaction method. Their structure, dielectric and ferroelectric properties are investigated. The incorporation of La^3＋ improves the den- sification and decreases the grain size of the ceramics without changing the crystal structure. The remanent polarization 2PT increases with increasing La content and reaches a maximum value of 22.8μC/cm^2 at x = 0.125, which is approximately 60% larger than that of pure SrBi2Nb2O9. The Curie temperature keeps almost unchanged at a value of about 440℃. The relationship between doping and the ferroeleetrie and dielectric properties are discussed.     

Low-temperature phase transformations in weakly doped quantum paraelectrics: novel features and quantum reentrant dipolar glass state in KTa0.982Nb0.018O3

An unusual sequence of phase transitions (PT) and reentrant dipole glass-like phase formation at low temperatures was found recently in KTaO₃ weakly doped with Li and Nb (K_0.9986Li_0.0014Ta_0.976Nb_0.024O₃) [Phys. Rev. B 63 (2001) 172]. We report on detailed low frequency (100 Hz-1 MHz) permittivity and Raman light scattering studies of similar composition, but without Li admixture, KTa_1−xNb_xO₃ with x=0.018 (KTN1.8). The aim of the study is to answer the question if the reentrant dipole glass-like phase exists in KTN1.8 and what is the microscopic origin of this phase. A detailed study of the sharp low-temperature PT observed at T_C∼27 K revealed properties inherent to the reentrant glass-type state at lower temperatures. The substitution of Nb for Ta influences the TO₁ soft lattice mode and leads to PT with the long-range ferroelectric ordering. A crossover to an order-disorder polar microregion dynamics with a non-standard ε′(T) behaviour and dipole glass-like formation were found below T_C (at ∼15 K), which is attributed to the randomness of the Nb distribution. A crossover to the long-range order was found under a dc bias field.     

Improvement in Dielectric Tunability of Ba0.6Sr0.4TiO4-Mg2TiO4 Composite Ceramics via Heterogeneous Nucleation Processing

Dielectric tunable composite ceramics Ba0.6Sr0.4 TiO4-Mg2 TiO4 （BST-MT） are prepared with a heterogeneous nucleation sol-gel approach. The Mg2 TiO4 powders are synthesized by the conventionM solid-state reaction method. The micro-sized MT powders with dispersant Ciba-4010 are introduced into Ba-Sr-Ti sol to obtain uniform and homogeneous mixture compounds with nano-sized BST particles synthesized via heterogeneous nucleation （HN） in the sol-gel process. Thus, the mierostructural and dielectric properties can be tailored. The dielectric constants of BST-MT composite ceramics can be adjusted in a larg＇e range from 294 to 1790, and the dielectric tunability can be adjusted from 29.4% to 37.0% with different MT contents from 60wt% to 20wt%. Compared to the samples prepared by the conventional solid-state （SS） process, the BST-MT composite ceramics by the heterogeneous nucleation sol-gel process exhibit a more uniform microstructure, and improve dielectric properties.     

Enhanced spontaneous polarization in Sr and Ca co-doped BaTiO3 ceramics

The dielectric and ferroelectric properties of (Ba_xSr_1−x)_0.77Ca_0.23TiO₃ ceramics with x=1 to 0.7 were studied and compared with those of Ba_xSr_1−xTiO₃ and Ba_0.77Ca_0.23TiO₃ ceramics. It has been found that Sr doping of the Ba_0.77Ca_0.23TiO₃ ceramics causes a drastic decrease of the Curie temperature, just like Sr doping of pure BaTiO₃ ceramics, demonstrating a cell volume effect. However, the (Ba_xSr_1−x)_0.77Ca_0.23TiO₃ ceramics with x=0.9 and 0.8 have larger spontaneous polarization than those of the corresponding Ba_xSr_1−xTiO₃ and Ba_0.77Ca_0.23TiO₃ ceramics, along with sufficient insulating properties. The enhancement of their polarization was explained by the increase of the lattice parameter c/a ratio due to the lattice distortion and strain developed in the ceramics.     

Microstructure-dependent giant dielectric response in CaCu3Ti4O12 ceramics

CaCu₃Ti₄O₁₂ ceramics were prepared at the sintering temperatures ranged from 1025 to 1125 °C, and the dielectric characteristics were evaluated together with the microstructures. The giant dielectric constant with the maximum of 53,120 was obtained in CaCu₃Ti₄O₁₂ ceramics at room temperature and 10 kHz, and strong processing and microstructure dependence of dielectric characteristics of the present ceramics was determined. The precipitation of the dispersed Cu-rich secondary phases of CuO and/or Cu₂O and their network structure provided the extrinsic origins of the enhanced giant dielectric response, and the present findings would offer the greater potential for enhancing the giant dielectric constant and controlling the dielectric loss in CaCu₃Ti₄O₁₂ ceramics by optimizing the microstructures.     

Ac behaviour and phase transition in PLZT 6/80/20 ferroelectric ceramics

The Ac behaviour of PLZT 6/80/20 ferroelectric ceramics was analyzed around and above the phase transition. Two relaxation processes are identified, showing that the so-called ‘universal relaxation law’ holds for the ceramics. A critical point in the values of the Ac conductivity, around the temperature corresponding to the maximum of the dielectric losses, is observed below the transition temperature due to the relaxor behaviour. The frequency dependence of the Ac conductivity at various temperatures and the hysteresis loops show classical relaxor behaviour with a diffuse phase transition.     

Sub-coercive field dynamic hysteresis in morphotropic phase boundary composition of Pb(Zr1/2Ti1/2)O3-Pb(Zn1/3Nb2/3)O3 ceramic and its scaling behavior

Sub-coercive field dynamic ferroelectric hysteresis of a morphotropic phase boundary composition of the PZT-PZN ceramic was investigated under influence of the compressive stress. The scaling relation of hysteresis area 〈A〉 against frequency f, field amplitude E₀, and stress σ took a form of , which is not different significantly to that of other PZT-PZN compositions with pure tetragonal or rhombohedral structure, as well as to that of soft and hard PZT bulk ceramics. This study suggested that the domain structures, not ceramic compositions, played a key role in controlling dynamic hysteresis behavior of ferroelectric materials.