First applicability of ZnGa2O4 : Ge, Li, Mn phosphor for a plasma display panel

The green emission intensity of ZnGa₂O₄:Ge⁴⁺, Li⁺, Mn²⁺ excited by the vacuum ultraviolet line of 147 nm reaches 70% of commercial green Zn₂SiO₄:Mn²⁺. The vacuum ultraviolet excitation spectra consist of four peaks. In a plasma display test bed filled with Ar and Ne plasma discharged by a radio-frequency generator of 13.6 MHz, ZnGa₂O₄:Ge⁴⁺, Li⁺, Mn²⁺ and commercial Zn₂SiO₄:Mn²⁺ phosphor screens show a linear increase in luminance with increasing self bias voltages. Increasing gas pressures cause the luminance to increase. Also, on increasing the self bias voltages and the gas pressures, the current densities of ZnGa₂O₄:Ge⁴⁺, Li⁺, Mn²⁺ phosphor screens are increased; this is the same behavior as that of the commercial phosphor.     

The origin of emission color of reduced and oxidized ZnGa2O4 phosphors

The Ga-O octahedral structure of the reduced and the oxidized ZnGa₂O₄ phosphors was investigated using Reitveld refinement. The correlation between the structural change and the changing emission color was studied. The emission peak shifts to shorter wavelength because of the more contribution of a variation of ligand charge than that of bond length to crystal field. The blueshift behavior of the reduced ZnGa₂O₄ was also observed in Ge⁴⁺-doped ZnGa₂O₄. In addition, Li⁺ ions doping in ZnGa₂O₄ generate extra oxygen ions, and Li⁺-doped ZnGa₂O₄ shows the same emission color as the oxidized ZnGa₂O₄.     

Energy transfer among three luminescent centers in full-color emitting ZnGa2O4:Mn, Cr phosphors

The ZnGa₂O₄:Mn²⁺, Cr³⁺ phosphors show three colors; the blue band of 380 nm from the charge transfer between Ga-O, the green band of 505 nm from Mn²⁺ and the red band of 705 nm from Cr³⁺. As a variation of Mn²⁺ or Cr³⁺ concentrations in ZnGa₂O₄:Mn²⁺, Cr³⁺, the relative emission intensity can be tuned. This phenomenon is explained in terms of the energy transfer based on four factors: the spectral overlap between the energy donors (Ga-O) and the energy accepters of Mn²⁺ or Cr³⁺, the absorption cross section of the energy accepters, the distance between them, and the decay time of the energy donors. ZnGa₂O₄:0.0025Mn²⁺, 0.010Cr³⁺ shows the CIE coordinates of x=0.4014, y=0.3368, which is a pure white light. The single-phased full-color emitting ZnGa₂O₄:Mn²⁺, Cr³⁺ phosphors can be applied to illumination devices.     

Enhanced photoluminescence properties of Zn2SiO4:Mn co-activated with Y/Li under VUV excitation

A series of green phosphors Zn_1.92−2xY_xLi_xSiO₄:0.08Mn²⁺ (0≤x≤0.03) were prepared by solid-state synthesis method. Phase and lattice parameters of the synthesized phosphors were characterized by powder X-ray diffractometer (XRD) and the co-doped effects of Y³⁺/Li⁺ upon emission intensity and decay time were investigated under 147 nm excitation. The results indicate that the co-doping of Y³⁺/Li⁺ has favorable influence on the photoluminescence properties of Zn₂SiO₄:Mn²⁺, and the optimal photoluminescence intensity of Zn_1.90Y_0.01Li_0.01SiO₄:0.08Mn²⁺ is 103% of that of commercial phosphor when the doping concentration of Y³⁺/Li⁺ is 0.01 mol. Additionally, the decay time of phosphor is much shortened and the decay time of Zn_1.90Y_0.01Li_0.01SiO₄:0.08Mn²⁺ is 3.39 ms, shorter by 1.83 ms than that of commercial product after Y³⁺/Li⁺ co-doping.     

Characterization of ZnGa2O4:Mn nanophosphor synthesized by the solvothermal method in 1,4-butanediol-water system

We characterized ZnGa₂O₄:Mn²⁺ (ZnGa₂O₄—zinc gallate) nanophosphor synthesized by the solvothermal method in 1,4-butanediol-containing water to increase the amount of Mn²⁺ ions incorporated in the ZnGa₂O₄ matrix without post-heat treatment. We investigated the influence of water content in the solvent on the photoluminescence (PL) intensity and the Mn amount, the latter being measured by X-ray fluorescence analysis and electron paramagnetic resonance spectroscopy. The PL intensity per Mn amount reached the maximum at the 50 wt% water content. The addition of water promotes repeated dissolution and precipitation, resulting in homogeneous Mn²⁺ distribution in the ZnGa₂O₄ matrix. This suggests that the solvothermal method in the 1,4-butanediol-water system is useful for increasing the amount of Mn²⁺ ions incorporated in the ZnGa₂O₄ matrix without post-heat treatment. At the water content >50 wt%, the decrease in PL intensity is attributed to the optical absorption of the by-product, MnOOH.     

Preparation and optical properties of Ce activated (Ca1 − x,Srx)Al2Si2O8 phosphors

(Ca_1 − x, Sr_x)Al₂Si₂O₈:0.06Ce³⁺, M⁺ (M⁺ = Li⁺, Na⁺, K⁺) phosphors have been prepared by conventional solid-state reaction method. The structural and optical properties of the phosphors were characterized by X-ray diffraction (XRD) technique and spectrophotometer, respectively. A regular variation was found among the XRD patterns of (Ca_1 − x, Sr_x)Al₂Si₂O₈:0.06Ce³⁺ phosphors based on the changing of Sr content. With the increase of Sr content, the maximum of emission band presented slight blue shifts (~ 15 nm). The luminescence intensity of CaAl₂Si₂O₈:0.06Ce³⁺ and SrAl₂Si₂O₈:0.06Ce³⁺ were significantly enhanced when K⁺ and Li⁺ were incorporated, respectively.     

Luminescent characteristics of LiCaBo3:M (M=Eu, Sm, Tb, Ce, Dy) phosphor for white LED

LiCaBO₃:M (M=Eu³⁺, Sm³⁺, Tb³⁺, Ce³⁺, Dy³⁺) phosphors were synthesized by a normal solid-state reaction using CaCO₃, H₃BO₃, Li₂CO₃, Na₂CO₃, K₂CO₃, Eu₂O₃, Sm₂O₃, Tb₄O₇, CeO₂ and Dy₂O₃ as starting materials. The emission and excitation spectra were measured by a SHIMADZU RF-540 UV spectrophotometer. And the results show that these phosphors can be excited effectively by near-ultraviolet light-emitting diodes (UVLED), and emit red, green and blue light. Consequently, these phosphors are promising phosphors for white light-emitting diodes (LEDs). Under the condition of doping charge compensation Li⁺, Na⁺ and K⁺, the luminescence intensities of these phosphors were increased.     

Photoluminescence characteristics of Se-doped ZnGa2O4:Mn2+ thin-film phosphors grown by pulsed laser deposition on Al2O3(0001) substrates

Se-doped ZnGa₂O₄:Mn²⁺ thin-film phosphors have been grown using a pulsed laser deposition technique at various growth conditions. Structural characterization was carried out on a series of Se-doped ZnGa₂O₄:Mn²⁺ films grown on Al₂O₃(0001) substrates using Zn-rich ceramic targets. The results of X-ray diffraction patterns showed that the lattice constants of the films decrease with the substitution of Se for the oxygen in the ZnGa₂O₄. Photoluminescence (PL) of Se-doped ZnGa₂O₄:Mn²⁺ thin films has indicated that Al₂O₃(0001) is a promising substrate for the growth of high-quality Se-doped ZnGa₂O₄:Mn²⁺ films. The emission spectra of Se-doped ZnGa₂O₄:Mn²⁺ films show a broad band extending from 479 to 550 nm and peaking at 508 nm. In particular, the incorporation of Se into the ZnGa₂O₄ lattice could induce an increase in the PL. The PL peak intensity of the Se-doped ZnGa₂O₄:Mn²⁺ films is a factor of 2.8 larger than that of the ZnGa₂O₄:Mn²⁺ films. This phosphor is promising for applications in flat-panel displays. PACS 78.20.-e; 78.55.-m; 78.66.-w     

Synthesis and luminescence properties of needle-like SrAl2O4:Eu, Dy phosphor via a hydrothermal co-precipitation method

Needle-like SrAl₂O₄:Eu²⁺, Dy³⁺ phosphors had been prepared by calcining the precursors obtained from hydrothermal process at the temperature of 1100 °C in a weak reductive atmosphere of active carbon. The crystal structure, morphology and optical properties of the composites were characterized. X-ray diffraction (XRD) patterns illustrated that the single-phase SrAl₂O₄ was formed at 1100 °C, which is much lower than that prepared by the traditional method. The transmission electron microscope (TEM) observation revealed the precursors and the resulted SrAl₂O₄:Eu²⁺, Dy³⁺ phosphors had well-dispersed distribution and needle-like morphology with an average diameter about 150 nm at the center and the length up to 1 μm. After irradiation by ultraviolet radiation with 350 nm for 5 min, the phosphors emit green color long-lasting phosphorescence corresponding to the typical emission of Eu²⁺ ion, both the PL spectra and luminance decay revealed that the phosphors had efficient luminescent and long lasting properties.     

The roles of Li and F ions in Li-F-codoped TiO2 system

An overall comparative study was carried out on Li-doped, F-doped, and Li-F-codoped TiO₂ powders in order to elucidate the roles of Li⁺ and F⁻ ions in photocatalyst. The characteristic data were based on the analysis of XRD, XPS, and PL spectra. The effects of atomic ratio of Li/Ti and F/Ti on the photocatalytic activity were also investigated. As the results, Li doping accelerated the phase formation of rutile in lower temperature while F doping prevented the phase transition from anatase to rutile. Li doping inducted a large amount of O_OH on the surface of TiO₂, while F doping consumed much of O_OH. Li⁺ ions acted as the roles of recombination center of electron-hole pairs while F doping could restrain the recombination of electron-hole pairs on the center of Li⁺ ions. The roles of Li⁺ and F⁻ ions were also confirmed in the experimental section, where the photocatalytic activity of TiO₂ was improved greatly by synergistic reaction of Li⁺ and F⁻ ions.     

Mn, Cr-co-doped MgAl2O4 phosphors for white LEDs

The Mn-, Cr-doped and Mn, Cr-co-doped MgAl₂O₄ powders have been synthesized via a gel-solid reaction method. Energy transfer from Mn²⁺ to Cr³⁺ has been observed for the first time in the co-doped MgAl₂O₄ phosphors. When excited with blue light with a wavelength of 450 nm at room temperature, both green emission from Mn²⁺ around 520 nm and red emission from Cr³⁺ around 675and 693 nm were generated. Moreover, the color of the emission can be modified by controlling the doping concentrations of Mn²⁺ and Cr³⁺. Therefore, MgAl₂O₄: Mn²⁺, Cr³⁺ could be used as a single-phased phosphor for white LED with a blue LED chip. The energy transfer in terms of Mn²⁺ to Cr³⁺ is determined by means of radiation and reabsorption.     

Synthesis and electrochemical performances of Li4Ti4.95Al0.05O12/C as anode material for lithium-ion batteries

Spinel compounds Li₄Ti_5−xAl_xO₁₂/C (x=0, 0.05) were synthesized via solid state reaction in an Ar atmosphere, and the electrochemical properties were investigated by means of electronic conductivity, cyclic voltammetry, and charge-discharge tests at different discharge voltage ranges (0-2.5 V and 1-2.5 V). The results indicated that Al³⁺ doping of the compound did not affect the spinel structure but considerably improved the initial capacity and cycling performance, implying the spinel structure of Li₄Ti₅O₁₂ was more stable when Ti⁴⁺ was substituted by Al³⁺, and Al³⁺ doping was beneficial to the reversible intercalation and deintercalation of Li⁺. Al³⁺ doping improved the reversible capacity and cycling performance effectively especially when it was discharged to 0 V.     

Charge compensation on the luminescence properties of ZnWO4:Tb phosphors via hydrothermal synthesis

A phosphor Tb³⁺-doped ZnWO₄ (ZWO:Tb) phosphors were prepared by a hydrothermal method. X-ray powder diffraction (XRD) analysis revealed that the as-obtained sample is pure ZnWO₄ phase. The excitation and emission spectra indicated that the phosphor could be well excited by ultraviolet light (272 nm) and emit blue light at about 491 nm and green light at about 545 nm. Significant energy transfer from WO₄²⁻ groups to Tb³⁺ ions has been observed. Two approaches to charge compensation are investigated: (a) 2Zn²⁺ = Tb³⁺ + M⁺, where M⁺ is a monovalent cation like Li⁺, Na⁺ and K⁺ acting as a charge compensator; (b) 3Zn²⁺ = 2Tb³⁺ + vacancy. Compared with two charge compensation patterns in the ZnWO₄:Tb³⁺, it has been found that ZnWO₄:Tb³⁺ phosphors used Li⁺ as charge compensation show greatly enhanced bluish-green emission under 272 nm excitation.     

Luminescent properties of R doped Sr2SiO4:Eu(R=Li, Na and K) red-emitting phosphors for white LEDs

Sr₂SiO₄:Eu³⁺ and Sr₂SiO₄:Eu³⁺ doped with R⁺(R⁺=Li⁺, Na⁺ and K⁺) phosphors were prepared by conventional solid-state reaction and investigated by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and photoluminescence spectroscopy. XRD patterns and SEM reveal that the optimal firing condition for Sr₂SiO₄:Eu³⁺ was 1300 °C for 4 h. The excitation and emission spectra indicate that the phosphor can be effectively excited by ultraviolet (395 nm) and blue (466 nm) light and emits intense red light peaked at around 614 nm corresponding to the ⁵D₀→⁷F₂ transitions of Eu³⁺. In the research work, the effect of R⁺ contents on luminescence property and the Eu³⁺ concentration quenching process have also been investigated. The Eu³⁺ concentration quenching mechanism was verified to be a multipole-multipole interaction and the critical energy-transfer distance was calculated to be around 14.6 Å. The dopant R⁺(R⁺=Li⁺, Na⁺ and K⁺) as charge compensator in Sr₂SiO₄:Eu³⁺ can further enhance luminescence intensity, and the emission intensity of Sr₂SiO₄:Eu³⁺ doping Li⁺ is higher than that of Na⁺ or K⁺.     

Enhanced luminescence in ZnGa<Subscript>2</Subscript>O<Subscript>4-x</Subscript>S<Subscript>x</Subscript>:Mn<Superscript>2+</Superscript> thin-film phosphors grown on MgO(100) substrate

Mn-doped ZnGa₂O_4-xS_x thin-film phosphors have been grown using a pulsed laser deposition technique at varying growth conditions. Structural characterization was carried out on a series of ZnGa₂O_4-xS_x:Mn²⁺ films grown on MgO(100) substrates using Zn-rich ceramic targets. Oxygen pressure was fixed at 100 mTorr and substrate temperatures were varied from 500 to 700 °C. The results of X-ray-diffraction patterns showed that the lattice constants of the ZnGa₂O_3.95S_0.05:Mn²⁺ thin films decrease with the substitution of sulfur for the oxygen in ZnGa₂O₄. Measurements of photoluminescence (PL) properties of ZnGa₂O_4-xS_x:Mn²⁺ thin films have indicated that MgO(100) is one of the most promising substrates for the growth of high-quality ZnGa₂O_4-xS_x:Mn²⁺ thin films. In particular, the incorporation of sulfur into the ZnGa₂O₄ lattice could induce a remarkable increase of PL. The highest green-emission intensity was observed with ZnGa₂O_3.95S_0.05:Mn²⁺ films, whose brightness was increased by a factor of 3.5 in comparison with that of ZnGa₂O₄:Mn²⁺ films. This phosphor may be promising for application to flat-panel displays. PACS 78.20.-e; 78.55.-m; 78.66.-w     

Small polaron migration in LixMn2O4: From first principles calculations

Migration of small polarons in λ-MnO₂, Li_0.5Mn₂O₄ and LiMn₂O₄ is studied via first principles calculations. Migration energy barriers of single small polaron migrations in λ-MnO₂, Li_0.5Mn₂O₄ and LiMn₂O₄ are 0.22 eV, 0.45 eV and 0.35 eV, respectively. The energy level changes of Mn-3d states along the polaron migration path are analyzed in detail. Results indicate that the activation energy barrier of polaron migration is strongly associated with the energy level shift of Mn-3dz² orbital, which is dependent on the short range structural arrangement of Mn³⁺/Mn⁴⁺ in the crystal. The electrical conduction properties of Li_xMn₂O₄ at room temperature are then discussed.     

Red emission in B- and Li-doped SrAl2O4:Eu phosphor under UV excitation

Samples of SrAl₂O₄:Eu³⁺ doped with B³⁺ and SrAl₂O₄:Eu³⁺ co-doped with B³⁺ and Li⁺ have been prepared by the solid-reaction method. The influence of B³⁺ and Li⁺ contents on luminescence property has been investigated. It is found that the substitution of B³⁺ for Al³⁺ greatly improves red emission intensity at 591, 615 and 701 nm. The dopant Li⁺ as charge compensator in SrAl₂O₄:Eu³⁺, B³⁺ can further enhance luminescence intensity. The strongest red emission is obtained in the Sr(Al_1.9, B_0.1)O₄:Eu_0.02³⁺, Li⁺_0.02 sample. The developed phosphors can be efficiently excited by ultraviolet (UV) light from 350 to 480 nm, which indicates that B³⁺ and Li⁺ co-doped SrAl₂O₄:Eu³⁺ is a good candidate phosphor applied in solid-state lighting in conjunction with white UV light-emitting diodes (LEDs).     

Advanced electrochemical performance of LiMn1.4Cr0.2Ni0.4O4 as 5 V cathode material by citric-acid-assisted method

Spinel LiMn₂O₄ and LiMn_1.4Cr_0.2Ni_0.4O₄ cathode materials were successfully synthesized by the citric-acid-assisted sol-gel method with ultrasonic irradiation stirring. The structure and electrochemical performance of the as-prepared powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectrometer, cyclic voltamogram (CV) and the galvanostatic charge-discharge test in detail. XRD shows that all the samples have high phase purity, and the powders are well crystallized. SEM exhibits that LiMn_1.4Cr_0.2Ni_0.4O₄ has more uniform cubic-structure morphology than that of LiMn₂O₄. EDX reveals that a small amount of Mn³⁺ still exists in LiMn_1.4Cr_0.2Ni_0.4O₄. The galvanostatic charge-discharge test indicates that the initial discharge capacities for the LiMn_1.4Cr_0.2Ni_0.4O₄ and LiMn₂O₄ at 0.15 C discharge rates are 130.8 and 130.2 mAh g⁻¹, respectively. After 50 cycles, their capacity are 94.1% and 85.1%, respectively. The CV curve implies that Ni and Cr dual substitutions are beneficial to the reversible intercalation and deintercalation of Li⁺, and suppress Mn³⁺ generation at high temperatures and provide improved structural stability.     

Combustion synthesis and luminescent properties of a new material Li2(Ba0.99,Eu0.01)SiO4:B for ultraviolet light emitting diodes

Using urea as fuel and boric as flux, a novel bluish green emitting phosphor Li₂(Ba_0.99,Eu_0.01)SiO₄:B³⁺ has been successfully synthesized using a combustion method. The material has potential application as the fluorescent material for ultraviolet light-emitting diodes (UV-LEDs). The dependence of the properties of Li₂(Ba_0.99,Eu_0.01)SiO₄:B³⁺ phosphors upon urea concentration, boric acid doping and initiating combustion temperature were investigated. The crystallization and particle sizes of Li₂(Ba_0.99,Eu_0.01)SiO₄:B³⁺ have been investigated by using powder X-ray diffraction (XRD) and transmission electron microscopy (TEM). Luminescence measurements showed that the phosphors can be efficiently excited by ultraviolet (UV) to visible region, emitting a bluish green light with peak wavelength of 490 nm. The results showed that the boric acid was effective in improving the luminescence intensity of Li₂(Ba_0.99,Eu_0.01)SiO₄ and the optimum molar ratio of boric acid to barium nitrate was about 0.06. The optimized phosphors Li₂(Ba_0.99,Eu_0.01)SiO₄:B_0.06³⁺ showed 160% improved emission intensity compared with that of the Li₂(Ba_0.99,Eu_0.01)SiO₄ phosphors under UV (λ_ex=350 nm) excitation.     

High luminance of new green emitting phosphor, Mg2SnO4:Mn

Mg₂SnO₄, which has an inverse spinel structure, was adopted as the host material of a new green emitting phosphor. Luminescence properties of the manganese-doped magnesium tin oxide prepared by the solid state reaction were investigated under vacuum ultraviolet (VUV) ray and low-voltage electron excitation. The Mg₂SnO₄:Mn phosphor exhibited green luminescence with the emission spectrum centered at 500 nm due to spin flip transition of the d-orbital electron associated with the Mn²⁺ ion. Optimum Mn concentration of Mg₂SnO₄:Mn under VUV excitation with 147 nm wavelength and electron beam excitation with 800 V excitation voltage are 0.25 and 0.6 mol%, respectively. The emission intensities of Mg₂SnO₄:Mn phosphors under the two excitation sources are higher than those of Zn₂SiO₄:Mn and ZnGa₂O₄:Mn phosphors. At 0.25 mol% of Mn concentration, on the other hand, the decay time is shorter than 10 ms.