Magnetoresistance and transport properties of different impurity doped La0.67Ca0.33MnO3 composite

An enhanced magnetoresistance and a two-fold effect result from impurity dopant were observed in composites of La_0.67Ca_0.33MnO₃/YSZ and La_0.67Ca_0.33MnO₃/Fe₃O₄. Where YSZ represents yttria-stabilized zirconia and the doping level of both YSZ and Fe₃O₄ is 1 mol%. Different electrical and magnetic transport properties, in particular a lower field magnetization behavior, were observed between pure La_0.67Ca_0.33MnO₃ and the impurity doped La_0.67Ca_0.33MnO₃ composites. Compared with pure La_0.67Ca_0.33MnO₃, a possible interpretation is presented by considering the influences of YSZ and Fe₃O₄ on the structure of grain boundaries and/or surfaces of La_0.67Ca_0.33MnO₃grains.     

Double-peak resistivity transport properties of La0.67Ca0.33MnO3 ceramics

Polycrystalline samples of La_0.67Ca_0.33MnO₃ were prepared by solid-state reactions by varying the pelletization force and the sintering temperature. Lowering the sintering temperature gave rise to smaller grains and increased the overall resistivity of the ceramic. Partial melting was observed in the ceramics sintered at higher temperatures (1400-1500 °C). Additionally, these ceramics showed two distinct resistivity peaks. The resistivity peak near the magnetic transition (T_C) was sharp, whereas the second peak was a broad one observed below T_C.     

Synthesis and enhanced low-field magnetoresistance in La0.67Ca0.33MnO3 /CuO composites

The (1−x)La_0.67Ca_0.33MnO₃+xCuO composites have been synthesized by a new liquid phase method. The XRD and SEM measurements reveal that little CuO is soluble in the structure of La_0.67Ca_0.33MnO₃ and is mainly distributed at the grain boundary of La_0.67Ca_0.33MnO₃. As CuO content x increases, the magnetization M values increase until x=0.05 and M values decrease when x further increases at low temperature. For x=0.10, 0.20 and 0.30 composites, double metal-insulator transitions accompanying a single ferromagnetic transition are observed. Large low-field magnetoresistance is achieved for the composites and the largest magnetoresistance appeared when x=0.20.     

Large room temperature magnetoresistance in YSZ doped La0.67Ba0.33MnO3 composite

The temperature dependence of the resistivity for composite samples of (1−x)La_0.67Ba_0.33MnO₃+xYSZ(LBMO/YSZ) with different YSZ doping level of x has been investigated in a magnetic field range of 0-7000 Oe, where the YSZ represents yttria-stabilized zirconia (8 mol% Y₂O₃+92 mol% ZrO₂). With increasing YSZ doping level, the range of 0-10%, the metal-insulator transition temperature (T_P) decreases. However, the resistivity, specially the low temperature resistivity, increases. Results also show that the YSZ doping level has an important effect on a low field magnetoresistance (LFMR). In the magnetic field of 7000 Oe, a room temperature magnetoresistance value of 20% was observed for the composite with a YSZ doping level of 2%, which is encouraging for potential application of CMR materials at room temperature and low field.     

Preparation and study of silver added La0.67Ca0.33MnO3 film

La_0.67Ca_0.33MnO₃ (LCMO) and Ag admixed La_0.67Ca_0.33MnO₃ (Ag-LCMO) polycrystalline films have been prepared on SrTiO₃ single crystal (100) substrates by ultrasonic spray pyrolysis technique. These films are characterized using XRD, SEM, and temperature dependence of resistivity (ρ-T) and ac susceptibility (χ-T). The films are having cubic structure with lattice parameters as 3.890 and 3.885 Å for LCMO and Ag-LCMO films, respectively. The peek in ρ-T curve (T_p) and the ferromagnetic transition temperature (T_C) for the Ag-LCMO film is higher than that of LCMO film. The stability of both the films was tested by repeated measurements of its characteristics over a period of one week after several thermal cycling from room temperature to 77 K. In the LCMO film, the peak in the ρ-T curve (T_p) is found to shift towards lower value and conduction noise of the film increases in the subsequent measurements. In the case of Ag-LCMO the value of T_p, T_C and conduction noise of the film did not change even after several measurements. Silver segregating at the grain boundaries in Ag-LCMO polycrystalline film seems to be responsible for improving the characteristics of Ag-LCMO films.     

Enhancement of magnetoresistances at room temperature in YSZ doping La0.67Sr0.33MnO3 system

The temperature dependence of the resistance of composite samples (1−x)La_0.67Sr_0.33MnO₃+xYSZ with different YSZ doping level x was investigated at magnetic fields 0-3 T, where YSZ represents yttria-stabilized zirconia. Results show that the YSZ dopant does not only adjust the metal-insulator transition temperature, but also increases the magnetoresistance effect. With increase of YSZ doping level for the range of x<2%, the metal-insulator transition temperature values T_P of the composites decrease, but T_P increases with increase of x further for the range of x>2%. Meanwhile, in the YSZ-doped composites, a broad metal-insulator transition temperature region was found at zero and low magnetic field, which results in an obvious enhanced magnetoresistance in the temperature range 10-350 K. Specially, a larger magnetoresistance value was observed at room temperature at 3 T, which is encouraging with regard to the potential application of magnetoresistance materials.     

Structural, magnetotransport and morphological studies of Sb-doped La2/3Ba1/3MnO3 ceramic perovskites

We report here the structural, magnetotransport and morphological studies of Sb-doped La_2/3Ba_1/3Mn_1−xSb_xO₃ perovskite manganites. Pristine material La_2/3Ba_1/3MnO₃ (LBMO) shows two insulator-metal (I-M) transitions in the electrical resistivity-temperature (ρ-T) behavior. While the higher temperature transition (T_P1) at ∼340 K is reminiscent of the usual I-M transition in manganites, the lower temperature transition (T_P2) at ∼250 K has been ascribed to the grain boundary (GB) effects arising out of the ionic size mismatch between the ions present at the rare-earth site (La³⁺ and Ba²⁺). With Sb-doping T_P1 shifts to lower temperatures while T_P2 remains invariant up to 3% and shifts to lower temperature for 5%. Room temperature electrical resistivity and the peak values also increase successively with Sb-doping. Scanning electron micrographs of the samples exhibit a gradual increase in their grain sizes with Sb indicating a gradual decrease in the GB density. Shift of T_P1 with doping is explained on the basis of a competition between double-exchange and super-exchange mechanisms. The overall electrical resistivity increases and the shift in the electrical resistivity hump (T_P2) with Sb-doping is found related to be gradually decreasing GB density and the ensuing lattice strain increase at the GBs. The intrinsic magnetoresistance (MR) gets suppressed and extrinsic MR gets enhanced with Sb-doping. At T>T_P1, the electrical resistivity is found to follow the adiabatic polaron hopping model whereas the electron-magnon scattering is found to dominate in the metallic regime (T<T_P1).     

Effect of Mn-site vacancies on the magnetic entropy change and the Curie temperature of La0.67Ca0.33Mn1−xO3 perovskite

Single-phase polycrystalline samples of La_0.67Ca_0.33Mn_1−xO₃ (x=0.00, 0.02, 0.04, 0.06) have been prepared using the sol-gel method. The structure, magnetocaloric properties and the Curie temperature of the samples with different Mn vacancy concentrations have been investigated. The experimental results show that vacancy doping at the Mn-sites has a significant influence on the magnetic properties of La_0.67Ca_0.33Mn_1−xO₃. The Curie temperature decreases monotonically with increasing the Mn-site vacancy concentration x. A remarkable enhancement of the magnetic entropy change has been obtained in the La_0.67Ca_0.33Mn_0.98O₃ sample. The entropy change reaches |ΔS_M|=3.10 J kg⁻¹ K⁻¹ at its Curie temperature (264 K) under an applied magnetic field H=10 kOe, which is almost the same value as that of pure Gd.     

Lanthanum deficiency effect in magnetic transition and transport property of La0.8−δCa0.2MnO3

The evolution of magnetic and electrical phases in La_0.8−δCa_0.2MnO₃ was investigated in terms of La deficiency. We found that the increase of the La deficiency tends to raise the Curie temperature (T_C) in La_0.8−δCa_0.2MnO₃. The FM clusters formed in compounds with large La deficiency provide percolation paths above T_C. With increasing the La defect, the transport property changes from insulating to metallic state, which is in association with the crossover from a second order to a first order magnetic phase transition in the vicinity of T_C.     

Epitaxial growth La0.67Ca0.33MnO3 thin film by radio frequency sputtering method

Perfect epitaxial growth of La_0.67Ca_0.33MnO₃ (LCMO) thin film has been achieved on (1 0 0) LaAlO₃ (LAO) single crystal substrate by radio frequency sputtering method. X-ray diffraction (XRD) and electron diffraction analysis indicates that La_0.67Ca_0.33MnO₃ film grows epitaxially on LaAlO₃ along [1 0 0] direction of the substrate. The resistivity variation with temperature of the film shows a sharp metal to semiconductor transition peak around 253 K, which is close to that of the target. The magnetoresistance (MR) also reveals high quality epitaxy film characteristic at low temperatures and near the metal to semiconductor transition temperature.     

Floating zone growth and magnetic and specific heat properties of La0.67Ca0.33Mn1-xFexO3（x=0.00,0.04）single crystals

Single crystals of La_0.67Ca_0.33MnO₃ and La_0.67Ca_0.33Mn_0.96Fe_0.04O₃ were obtained by floating zone method. Laue diffraction pattern and rocking curve of the single crystals show that their quality is good. The magnetic behaviours of these compounds have been studied. Fe doping significantly depresses the magnetic contribution to the total specific heat C_P, but slightly influences the lattice contribution at temperatures above 50K. The peak of C_P shifts towards high temperatures with increasing magnetic field. Both single crystals exhibit the first-order magnetic transition around the Curie temperature.     

Enhanced ferromagnetic transition temperature in nanocrystalline lanthanum calcium manganese oxide (La0.67Ca0.33MnO3)

We report a novel, low temperature (450-600 °C) route for the synthesis of highly crystalline and homogeneous nanoparticles of lanthanum calcium manganese oxide La_0.67Ca_0.33MnO₃ (LCMO). The nanocrystallites, with average particle size of 30 nm, possess a ferromagnetic-paramagnetic transition temperature (T_c) of 300 K, which is about 50 K higher than that of a bulk single crystal. The transition temperature was found to be inversely proportional to the particle size. The Rietveld analysis of the powder X-ray diffraction data of the phase-pure nanopowders reveals that the particle size reduction leads to a significant contraction of the unit cell volume and a reduction of the unit cell anisotropy. We propose that these two lattice effects are responsible for the observed enhancement in T_c.     

Large enhancement of room temperature magnetoresistance in Ag-added La0.67(Ca0.65Ba0.35)0.33MnO3

The electrical and magnetoresistant properties of La_0.67(Ca_0.65Ba_0.35)_0.33MnO₃/Ag_x (abbreviated by LCBMO/Ag_x) have been studied. The results show that Ag addition causes a decrease of resistivity dramatically and especially induces a large enhancement of room temperature magnetoresistance (MR). The room temperature MR ratio for x=0.27 sample in 10 kOe magnetic field is 41%, almost 20 times larger than that for x=0 sample. This enhancement is related to that the Curie temperature (T_c) of the sample is near room temperature, as well as the significant reduction of resistivity. The good fits of experimental results for x=0.27 sample to Brillouin function indicate that the MR behavior in the Ag added LCBMO is induced by the spin-dependent hopping of the electrons between the spin clusters, which is an intrinsic property of the CMR materials.     

The correlation between structure and magnetic properties in the manganites La0.7Ca0.3−xTexMnO3 (0≤x≤0.15)

The effect of Te-doping at La-site on structural, magnetic and transport properties in the manganites La_0.7Ca_0.3−xTe_xMnO₃ (0≤x≤0.15) has been investigated. All samples show an orthorhombic structure (O′-Pbnm) at room temperature. It shows that the Mn-O-Mn bond angle decreases and the Mn-O bond length increases with the increase in the Te content. All samples exhibit an insulator-metal (I-M) transition and the resistivity increases with the increase in the Te-doping level. Additionally, the Curie temperature T_c decreases and the transition becomes broader with increasing Te-doping level, in contrast, the magnetization of Te-doping samples at low temperatures decrease with increasing x as x≤0.10 and then increase with further increasing x to 0.15. The results are discussed in terms of Jahn-Teller (JT) vibrational anisotropy Q₃/Q₂ and the opening of the new DE channel between Mn²⁺-O-Mn³⁺ due to the introduction of Mn²⁺ ions because of the substitution of Te⁴⁺ ions for Ca²⁺ ions.     

Metastable structure and properties of (La0.73Bi0.27)0.67Ca0.33MnO3

The electrical transport and magnetic properties of high Bi doped (La_0.73Bi_0.27)_0.67Ca_0.33MnO₃ are studied at the temperature and magnetic field ranges from 10 to 300 K and 0 to 3 T. Significant temperature and magnetic field hystereses are observed in both resistivity and magnetization measurements. Meanwhile, an enhanced magnetoresistance effect, within a wide temperature window, is obtained in the (La_0.73Bi_0.27)_0.67Ca_0.33MnO₃. The hysteresis and enhanced magnetoresistance are discussed based on an inhomogeneous metastable structure related to the Bi dopant.     

Ti/Pr0.7Ca0.3MnO3/La0.67Sr0.33MnO3/Pt异质结电致电阻效应的改善

采用脉冲激光沉积技术制备了Ti/Pr_0.7Ca_0.3MnO₃/Pt和Ti/Pr_0.7Ca_0.3MnO₃/La_0.67Sr_0.33MnO₃/Pt异质结并研究了La_0.67Sr_0.33MnO₃功能插层对异质结电致电阻特性的影响. 实验结果表明La_0.67Sr_0.33MnO₃功能层的引入有效提高了器件的电阻转变特性,尤其是电阻转变率和疲劳性得到了极大的改善. 对La_0.67Sr_0.33MnO₃插层改善电致电阻转变特性的机理进行了定性的分析. 关键词： 电致电阻效应 电阻转变比率 疲劳特性     

Search for high temperature coefficient of resistance La2/3Ca1/3MnO3 polycrystalline ceramics

La_2/3Ca_1/3MnO₃ polycrystalline ceramics were synthesized by sol–gel method. Sharp temperature coefficient of resistance (TCR) variation (with peak value up to 22 %) has been observed near the metal-insulator transition temperature T _MI (273 K) for the sample sintered at 1,450 °C. This TCR value is much higher than the previously reported values for the undoped and Ag-doped La_0.67Ca_0.33MnO₃ samples and is comparable to the optimized thin films. It was concluded that the improved physical properties of the La_0.67Ca_0.33MnO₃ material are due to its improved microstructure and homogeneity.     

Temperature dependence of electroresistance for La0.67Ba0.33MnO3 manganite

The influence of dc biasing current on temperature dependence of resistance of La_0.67Ba_0.33MnO₃ bulk sample is reported. A decrease in the resistance (electroresistance) on the application of higher bias current is observed. The electroresistance is maximum at metal-insulator transition temperature (T_MI) and decreases when the temperature is either increased or decreased from T_MI. A two-phase model is proposed to explain the occurrence of electroresistance. The higher bias current leads to an increase in alignment of spins and thus, in turn, leads to an increase in spin stiffness coefficient and decrease in the resistance at T_MI.     

Electrical transport and magnetic properties of La2/3Ca1/3MnO3/SiO2 composites

The influence of SiO₂ on the electrical transport properties of LCMO/SiO₂ composites with different SiO₂ contents x is investigated, where LCMO represents La_2/3Ca_1/3MnO₃. Results show that the SiO₂ phase not only shifts the metal–insulator transition temperature (T_p) to a high temperature range, but also has an effect on the magnetoresistance (MR) of the composites. The temperature dependence of resistivity indicates that the T_p of the composites is obviously higher than that of pure LCMO, and that the peak resistivity ρ_max of the composites is lower than that of pure LCMO. In the SiO₂ content x∼0.02, the T_P is the highest and ρ_max becomes the lowest. The experimental observation is discussed on the basis of the analysis of scanning electron microscopy (SEM) images and X-ray diffraction (XRD) patterns. Compared with pure LCMO, a possible interpretation is presented by considering the influence of SiO₂ on the coupling between ferromagnetic (FM) domains of LCMO.     

Room temperature magnetoresistance in Ln2/3A1/3MnO3 manganites

The investigation of the manganites La_2/3−xPr_xSr_1/3MnO₃, La_2/3Sr_1/3−xCa_xMnO₃ and La_2/3+xCa_1/3−2xAg_xMnO₃, which all exhibit Mn³⁺:Mn⁴⁺=2, shows that it is possible to reach high magnetoresistance at room temperature, up to 21% under 1.2 T. These materials are compared to La_5/6Ag_1/6MnO₃ which corresponds to the same Mn³⁺:Mn⁴⁺ ratio and exhibits a magnetoresistance of 25% in this field. An interesting feature deals with the value of the insulator-metal transition temperature T_IM, often higher than T_C, especially for Ag-based compounds. It is suggested that the latter results either from a better oxygenation of the surface of the grains or from a migration of silver toward the surface.