Sensitive determination of nitrite by means of a Landolt-type reaction in fluorescent aggregates of a binaphthyl-based amphiphile

The iodine quenching effect on the fluorescence of a binaphthyl-based amphiphile, C₈BNC₆N, was used for monitoring the Landolt-type reaction between nitrite, iodide, and thiosulfate. Due to the possibility of iodine detection in the 10^–8–10^–7 M range, and to the effective concentration of anionic reagents on the surface of cationic aggregates, the indicator reaction can be monitored using reagents at concentration levels as low as 10^–7 M. To optimize the analytical system, the effect of pH and reagent concentrations on the rate of indicator reaction were studied. The influence of the matrix of water samples and effect of side-reactions increasing the value of a blank test were examined. A procedure for nitrite determination in water was developed, using the diazo reaction for selective nitrite removal to provide a reference solution, which avoided possible effects of the matrix components. The usefulness of this method was tested by determining trace amounts of nitrite in water samples. The procedure allows determination of nitrite down to 5 ng/ml (detection limit about 2ng/ml) with r.s.d. of 10% in the 20–250 ng/ml range.     

Fluorometric Determination of Nitrogen Dioxide in Atmosphere Sampled by the Liquid Droplet Technique

A new, simple, sensitive and selective fluorometric method for the determination of nitrite has been developed. The reaction of nitrite with hydralazine in acidic medium, heated on a boiling water-bath for 15 min, produced a tetrazolo (5,1-a) phthalazine (Tetra-P). The product formed was measured at _ex = 274 nm and _em = 345 nm. The fluorescence intensity was valid over a nitrite concentration range 0.067–60.3 ng mL^–1, with a detection limit of 0.0091 ng mL^–1. The reproducibility of the proposed method was determined by running a different concentration of nitrite, 13.4, 33.5, and 46.9 ng mL^–1. The % recoveries and the relative standard deviations were found to be 100.6 ± 0.9, 99.9 ± 0.5, and 99.4 ± 1.1%, respectively. The proposed method was applied successfully to the determination of nitrogen dioxide sampled from the atmosphere using the liquid droplet method. The nitrogen dioxide our wind tunnel was controlled by an NO _x analyzer based on a chemiluminescence analyzer detector (CLAD 1000). A linear graph was obtained for the nitrogen dioxide in the wind tunnel vs. NO₂ sampled by the liquid droplet method. The effect of interference substances in the determination showed that cations and anions did not disturb the process. The results obtained were satisfactory when compared with the reference method.     

Colorimetric determination of palladium (II) by means of promazine hydrochloride

In acetate buffer medium palladium(II) ions form with promazine hydrochloride (PM) two complexes: an orange one of a formula [Pd(C₁₇H₂₀N₂S)]²⁺ (λ_max = 460 nm, ε = 4.5 × 10³, at 20 °C and pH = 2) and a violet one of a formula [Pd(C₁₇H₂₀N₂S)₂]²⁺ (λ_max = 540 nm, ε = 8.8 × 10³ at 20 °C and pH = 2).The values for instability constants determined by Bjerrum's method amount to pK₁ = 3.95; pK₂ = 3.07; pβ₁ = 3.95; pβ₂ = 7.02, respectively.A colorimetric method of the determination of palladium(II) has been elaborated. The method consists in a measurement of the absorbance of the violet complex of palladium(II) with promazine hydrochloride at λ = 540 nm. The method permits the determination of 2–17 μg Pd/ml with an error of ±2%. The time of the determination is 20 min. Iron(III), Ce(IV), Pt(IV), V(V), Cr(VI), and HNO₃ interfere with the determination.     

Fluorimetric reaction-rate method for determination of mercury with 2,2′-dipyridylketone hydrazone

A simple and sensitive fluorimetric reaction-rate method for determination of mercury(II) (0.03-0.3 ppm), based on its catalytic effect on the autoxidation of 2,2′-dipyridylketone hydrazone, has been developed. The reaction is followed by the measurement of the rate of appearance of blue fluorescence (λ_ex = 359 nm, λ_em = 430 nm). The experimental variables and interferences in the determination are also reported.     

Fluorometric Determination of Traces of Nitrite with Rhodamine 6G

A simple and highly selective fluorometric method for determining nitrite with rhodamine 6G is described. The method is based on the oxidation of rhodamine 6G in sulfuric acid medium. A linear calibration graph passing through the origin was obtained in the range 0.02–0.4 μg/ml nitrite. The detection limit is 0.001 μg/ml. The method is free from interference by Fe(III) and Cu(II), which normally interfere with other methods. The method was applied successfully to the determination of nitrite in tap water, lake water, and milk samples.     

Some observations on the spectrophotometric determination of amino acids via interaction with p-benzoquinone

Spectrophotometric quantitative determination of amines and sulfa drugs via interaction with p-benzoquinone was extended to determination of amino acids, whereby the colored products obtained display maximum absorption at λ = 490–500 nm, E₁ cm^1% in the range 160–480, and a concentration range of 1.5–34.0 μg/ml. The effects of time, concentration, temperature, and cooling on the nature of the reaction product were investigated. The reaction proved to be irreversible. A monosubstituent compound is more easily formed in the presence of excess p-benzoquinone. A linear relation between the formation constant (K_f) and pK_α for the tested amino acids has been observed. Determination of adrenaline by this method is considered to offer an indirect means of determination of tyrosine.     

Sensitive spectrofluorimetric determination of ruthenium at nanotrace levels using 2-(α-pyridyl) thioquinaldinamide [PTQA]

A new spectrofluorimetric method for the determination of ruthenium with nonfluorescent 2-(α-pyridyl) thioquinaldinamide (PTQA) is described. The oxidative reaction of Ru(III) upon PTQA gives oxidised fluorescent product (λ_ex(max)=347 nm; λ_em(max)=486 nm). The sensitivity of the fluorescence reaction between ruthenium and PTQA is greatly increased in the presence of Fe (III). The reaction is carried out in the acidity range 0.01–0.075 M H₂SO₄. The influence of reaction variables is discussed. The range of linearity is 1–400 μg l⁻¹ Ru(III). The standard deviation and relative standard deviation of the developed method are ±1.210 μg l⁻¹ Ru (III) and 2.4%, respectively (for 11 replicate determinations of 50 μg l⁻¹ Ru (III)). The effect of interferences from other metal ions, anions and complexing agents was studied; the masking action is discussed. The developed method has been successfully tested over synthetic mixtures of various base metals and platinum group metals, synthetic mixtures corresponding to osmiridium, certified reference materials in spiked conditions and rock samples.     

Absorptiometric determination of micro- and submicroamounts of iron using an extractive method with pyridine-2-acetaldehyde salicyloylhydrazone

The formation and extraction into chloroform of iron complex with PASH (λ_max = 640 nm) was studied. Beer's law is obeyed between 2.7 and 16.0 μg · ml⁻¹ of iron, in organic phase (10 ml). The method can be applied to volume ratios V_aq.:V_org. from 1:1 to 20:1. The minimum concentration determinable in aqueous phase is 135 ng ml⁻¹ of iron. The interferences of 73 species were evaluated and eliminated when it was possible. The extraction method of the green complex was applied for the spectrophotometric determination of iron(II) in several standard, geochemical, and bromatological samples. A procedure based on the standard addition method was applied satisfactorily to the determination of as little as 25 ng of iron(II) per milliliter.     

Spectrophotometric determination of traces of nitrite with rhodamine 6 G

A simple and highly selective spectrophotometric method is described for the determination of nitrite. The method is based on the measurement of decrease in absorbance at 525 nm of rhodamine 6 G in sulphuric acid medium. The decrease in absorbance is instantaneous on addition of nitrite and remains stable for 2 h. Linear calibration graph passing through the origin was obtained in the range 0.01–0.6 g/ml nitrite. The method is free from interference of Cu²⁺, Fe³⁺ and SO ₃ ^2– which normally interfere in other procedures. The method was applied successfully to the determination of nitrite in well and sea water samples and in KNO₃, NaNO₃, table salt, sugar and milk powder samples.     

Spectrophotometric determination of molybdenum by extraction of its thiosulphate complex

A simple and rapid spectrophotometric determination of molybdenum is described. The molybdenum thiosulphate complex is extracted into isoamyl alcohol from 1·0–1·5M hydrochloric acid containing 36–40 mg of Na₂S₂O₃·5H₂O per ml. The absorbance at λ_max = 475 nm obeys Beer's law over the range 0–32 μg of Mo per ml of solvent phase. Up to 5 mg/ml of Ti(IV), V(V), Cr(VI), Fe(III), Co(II), Ni(II), U(VI), W(VI), Sb(III), 1 mg/ml of Cu(II), Sn(II), Bi(V) and 10 μg/ml of Pt(IV) and Pd(II) do not interfere. Large amounts of complexing agents interfere. The method has been applied to analysis of synthetic and industrial samples.     

新型荧光试剂1,5-二(4,6-二氯三嗪)-氨基萘与酪氨酸相互作用

合成了一种新型三嗪荧光探针1,5-二(4,6-二氯三嗪)-氨基萘并利用元素分析、IR和核磁共振谱进行了表征。在pH=12.0的柠檬酸钠-NaOH缓冲溶液中,与酪氨酸在35℃下反应30 min后,λex/λem=400 nm/465 nm处,1,5-二(4,6-二氯三嗪)-氨基萘与酪氨酸反应使体系的荧光强度增强,且增强的荧光强度与酪氨酸的浓度成正比,依此建立了一种测定酪氨酸的新方法。测定的线性范围是1.1×10-7~1.1×10-5mol/L,检出限为6.8×10-8mol/L。该方法成功用于测定人尿和血清样品中的酪氨酸。     

Flow-Injection Spectrophotometric Determination of Hydrazine

A flow-injection spectrophotometric method for the determination of hydrazine is described. The method is based on the inhibitory effect of hydrazine on the reaction of thionine with nitrite in acidic media. The decolorization of thionine by the reaction with nitrite was used to monitor the reaction spectrophotometrically at 602 nm. The variables that affected the reaction rate were fully investigated and the optimum conditions were established. Hydrazine can be determined in the range 2.0–40.0 μg/ml with a limit of detection of 1.0 μg/ml. The relative standard deviation for 10 replicate determinations of 7.0 μg/ml hydrazine is 3.3%. The method is simple, rapid, and widely applicable.     

A new selective reagent for the spectrofluorometric determination of beryllium

The fluorescence properties of the beryllium and aluminum complexes with 2, 4-dioxo-4-(4-hydroxy-6-methyl-2-pyrone-3-yl) butyric acid ethyl ester (Ligand) were studied and optimal conditions for their fluorometric determination were established. Beryllium can be determined in the linearity range of 0.5–2.0 μg/ml and aluminum 0.5–1.5 μg/ml. The effect of diverse ions on the determination of beryllium is discussed.A simple procedure for the fluorometric determination of beryllium in human blood plasma in the concentration range of 5–50 μg Be/ml is described.     

Sensitive, selective spectrophotometric determination of phenols with periodic acid

A new spectrophotometric determination of phenols with periodic acid has been developed. The colored product of phenol periodic acid reaction has a λ_max 380 nm. The determination of phenol, pyrocatechol, α-naphthol, β-naphthol, quinol, p-cresol, m-cresol, 8-quinolinol, resorcinol, phloroglucinol, and gallic acid has been done. The effects of possible variables e.g., temperature, reagent, pH buffers have been studied. A study of interferences is made. Mechanism of the reaction is discussed.     

Single-Step Hydrolysis and Derivatization of Homocysteine Thiolactone Using Zone Fluidics: Simultaneous Analysis of Mixtures with Homocysteine Following Separation by Fluorosurfactant-Modified Gold Nanoparticles

Herein, we report a new automated flow method based on zone fluidics for the simultaneous determination of homocysteine and homocysteine thiolactone using fluorimetric detection (λ_ext = 370 nm/λ_em = 480 nm). Homocysteine thiolactone is hydrolyzed on-line in alkaline medium (1 mol L⁻¹ NaOH) to yield homocysteine, followed by reaction with o-phthalaldehyde in a single step. Derivatization is rapid without the need of elevated temperatures and stopped-flow steps, while specificity is achieved through a unique reaction mechanism in the absence of nucleophilic compounds. Mixtures of the analytes can be analyzed quantitatively after specific separation with fluorosurfactant-capped gold nanoparticles that are selectively aggregated by homocysteine, leaving the thiolactone analogue in solution. As low as 100 nmol L⁻¹ of the analyte(s) can be quantified in aqueous solutions, while concentrations > 2 μmol L⁻¹ can be analyzed in artificial and real urine matrix following 20-fold dilution. The percent recoveries ranged between 87 and 119%.     

Spectrofluorometric study of 1,4-diaminoanthraquinone-calcium complex in aqueous sulfuric acid mediums: Spectrofluorometric determination of calcium

The spectrofluorometric study was made of the complex 1,4-diaminoanthraquinone-Ca in aqueous sulfuric mediums [λ_max,ex = 410 nm; λ_max,em = 580 nm; 50% H₂O; stable for at least 4 hr; range temperature OPTIMUM = 20–35 °C; [R]_optimum = 2 × 10⁻⁴M; stoichiometry 2:1 (fluorescent complex) and 1:1 (no fluorescent complex)]. A new method for the spectrofluorometric determination of Ca traces is proposed for concentrations between 150 and 400 ppb. The relative error and the interferences of the method have been investigated.     

Studies on Simultaneous Fluorescence-Spectrophotometric Determination of Ultratrace Niobium(V), Tantalum(V), and Zirconium(IV) Using Partial Least-Squares Algorithm

In the presence of cetyltrimethylammonium bromide, a cationic surfactant, highly sensitive molecular fluorescence reactions occur between Nb(V), Ta(V), and Zr(IV) ions and morin (3, 5, 7, 2′, 4′-pentahydroxyflavone) in acidic medium to form stable ternary micellar complexes. Their λ_ex(max)/λ_em(max)values are 421.0/492.2, 416.2/489.6, and 424.2/507.8 nm, respectively, and their λ_em(max)values are 490.5, 488.6, and 507.2 nm, respectively, at the same fixed λ_exof 420.5 nm, indicating their seriously overlapping fluorescence excitation spectra and fluorescence emission spectra. The linear ranges of their regression calibration curves are 0 to 0.20, 0 to 0.50, and 0 to 0.20 mg/liter, respectively, with 0.5 ng/ml for all of sensitivities. The simultaneous molecular fluorescence-spectrophotometric determination of ultratrace or trace Nb(V), Ta(V), and Zr(IV) without separation was made using a partial least-squares (PLS) algorithm and other algorithms. The optimum PLS computation conditions are wavelength point number of 25 and corresponding wavelength range from 450 to 550 nm oriented from λ_em500 nm to two sides at combined intervals of 2.5 and 5.0 nm at a fixed λ_exof 420.5 nm with an optimum calibration sample number of 14 and respective optimum abstracted factor numbers of 6, 4, and 3. With respect to both accuracy and precision of the obtained results, the PLS algorithm is superior to the ordinary least-squares algorithm.     

Flow injection determination of nitrite by fluorescence quenching

A simple, sensitive and selective fluorimetric method for the determination of nitrite ion in waters using a merging zones flow injection system is described. The fluorimetric determination is based on the measurement of the quenching effect produced by nitrite on proflavine (3,6-diaminoacridine) fluorescence (λ_ex/λ_em=290/519 nm).

The optimum experimental conditions were investigated by merging 0.5 ml of the sample and 0.5 ml of a solution of 5 mg l⁻¹ of proflavine (in 0.1 M HCl) in a flow injection system, on-line connected to a flow-cell placed in the conventional sample compartment of a spectrofluorimeter. The selected carrier solution and final flow rate were 0.1 M HCl and 0.5 ml min⁻¹, respectively. A reaction coil of 2 ml was used. As a result of the simplicity of this system, a sample throughput of about 50 samples h⁻¹ can be achieved with the proposed methodology.

The detection limit was 1.1 ng ml⁻¹ (3σ criterion) of nitrite. The repeatability for five sample injections containing 100 ng ml⁻¹ of nitrite was ±0.3% and the observed linear range extended up to 400 ng ml⁻¹. Also, the effect of interferences from various metals and anions commonly present in waters was also studied.

The method was successfully applied to the determination of low levels of nitrite in different water samples (river, fountain, tap and commercial drinking waters).     

Extraction and spectrophotometric determination of vanadium with 4-(2-thiazolylazo)resorcinol and tetraphenylarsonium and phosphonium chlorides

Extraction of vanadium-4-(2-thiazolylazo)resorcinol complexes by quaternary salts such as triphenylmethylarsonium iodide, tetraphenylarsonium chloride, and tetraphenylphosphonium chloride has been studied. Quantitative extraction is achieved with tetraphenylarsonium and tetraphenylphosphonium chlorides in the pH region between 3.5 and 5. The optimum conditions for the extraction and spectrophotometric determination of vanadium in the extract are: pH 3.8–4.0, the concentration of vanadium 0.1–0.4 μg/ml. Effective molar absorptivity at λ_max = 555 is (2.55 ± 0.05) × 10⁴ liters mol⁻¹ cm⁻¹. Beer's law is obeyed. Relative standard deviation is 2–10% depending on the concentration level. The composition of the extracted complexes was studied in the solution and in the solid state. For their characterization chemical and spectral evidence and comparison with the vanadium-PAR complexes have been combined.     

Selective Determination of Cytosine Based on Its Fluorogenic Reaction with Triethylamine/Chloroacetonitrile

Abstract

A sensitive fluorometric method is described For selective determination of cytosine in nucleobases. The method is based on chemical derivatization of cytosine by triethylamine/chloroacetonitrile. The effects of solvent, reaction temperature, reaction time and concentration of reagents on the efficiency of the reaction were studied. A good linear relationship between fluorescence intensities and cytosine concentrations in the range of 2.0–800 ng/mt was observed. The detection limit for cytosine is 0.6 ng/ml (S/N=3). The relative standard deviations (7 replicates) for measurements of 50 and 500 ng/ml cytosine were 2.1 and 2.5%, respectively.