Synthesis and characterization of side-chain cholesteric elastomers derived from an isosorbide crosslinking agent

New liquid crystalline monomer 4-(4-ethoxybenzoyloxy)biphenyl-4′-[(10-undecylen-1-yloxy)-4′-ethoxy]benzoate (M ₁ ), chiral crosslinking agent isosorbide di-(10-undecylen-1-yloxybenzoate) (M ₂ ), and the corresponding elastomers were prepared. The chemical structures of M ₁ and M ₂ were characterized by Fourier transform infrared and ¹H-nuclear magnetic resonance. The mesomorphic properties and phase behavior were investigated by differential scanning calorimetry, thermogravimetric analysis, polarizing optical microscopy, and X-ray diffraction measurements. M ₁ exhibited typical threaded texture and droplet texture of nematic phase. The use of chiral crosslinking agent in the polymer networks could induce cholesteric phase. The elastomers containing less than 10 mol% of the chiral crosslinking units showed elasticity, reversible phase transition, wide mesophase temperature ranges, and high thermal stability. For the elastomers P ₂ –P ₄ , the glass transition temperature (T _g) increased; clearing temperature (T _i) and mesophase temperature range (ΔT) decreased with increasing content of the crosslinking unit.     

Influence of an interfacial agent on the structure of polypropylene-polyamide fibres

In this paper the structure and properties of fibres prepared from the polypropylene/polyamide (PP/PA6) blend have been studied as a function of the interfacial-agent (IFA) content. For this purpose the grafted polypropylene-maleic anhydride copolymer was used. Fibres containing 20% of PA6 and 80% of PP possess the phase matrix-fibril structure. The size and distribution of fibres in the dispersed PA6 phase in the PP matrix depend on the interfacial-agent amount. Due to the indirect nucleating effect the PA6 phase has been found to act, in the presence of the interfacial agent, on the PP crystallization during fibre formation. As a result, undrawn fibres have the more pre-oriented and crystalline PP matrix with the morphological rod-like structure. The pre-orientation of the dispersed fibrilar PA6 phase is minimum. Mechanical properties of the drawn blended fibres are favourably influenced provided that the interfacial-agent concentration is higher than 1%. The growing rate of the mutual interaction between the components was mostly reflected in the increased values of Young's modulus.     

Infrared spectroscopy studies of the cyclic anhydride as the intermediate for the ester crosslinking of cotton cellulose by polycarboxylic acids. III. Molecular weight of a crosslinking agent

Polycarboxylic acids have been used as nonformaldehyde crosslinking agents for cotton fabrics to replace the traditional N-methylol reagents. In this research, we compared 1,2,3,4-butanetetracarboxylic acid (BTCA) with poly(maleic acid) (PMA) as crosslinking agents for cotton cellulose. BTCA and PMA have similar molecular structures with carboxyl groups bonded to their molecular backbones, and both form five-membered cyclic anhydride intermediates during a curing process. However, BTCA is a more effective crosslinking agent for cotton cellulose than PMA. This is mainly attributed to the differences in the mobility of the anhydride intermediates to access the cellulosic hydroxyl groups during a curing process. The mobility of the anhydride intermediate of PMA is reduced due to its molecular size and multiple bonding between a PMA molecule and cellulose. Consequently, more anhydride and less ester are detected on the cotton fabric treated with PMA than on the fabric treated with BTCA. The amount of the unreacted anhydride intermediate on the fabric treated with PMA is reduced whereas the amount of ester is increased when another hydroxyl-containing compound of low molecular weight is present. Thus, the infrared spectroscopy data show a clear link between the molecular weight of a polycarboxylic acid and its effectiveness for crosslinking cotton cellulose. © 1997 John Wiley & Sons, Inc.     

Antimicrobial cotton fibres prepared by in situ synthesis of AgCl into a silica matrix

Functional antimicrobial cotton fibres were prepared in a novel two-step procedure utilising the pad-dry-cure method to apply an inorganic–organic hybrid sol–gel precursor (reactive binder, RB) followed by the in situ synthesis of AgCl particles on the RB-treated fibres. The morphology and surface composition of the modified cotton fibres were investigated by scanning electron microscopy imaging and X-ray photoelectron spectroscopy and energy-dispersive X-ray spectroscopy spectral analyses. The bulk concentration of Ag on the cotton fibres was determined by inductively coupled plasma mass spectroscopy, and the antimicrobial activity against the bacteria Escherichia coli and Staphylococcus aureus was estimated according to the ISO 20645:2004 (E) and AATCC 100-1999 methods. The results showed that this application process yields the following important benefits: (1) the presence of the RB silica matrix increased the fibres’ capacity for adsorbing AgCl particles compared with the same fibres without RB; (2) the in situ synthesis enabled a simple and environmentally friendly preparation of AgCl particles from AgNO₃ and their embedment into the fibres; (3) the AgCl particles were bound to the RB silica matrix by physical forces, which allowed for their controlled release from the fibres; (4) the capacity of the RB-modified cotton samples to hold embedded AgCl particles was sufficient to provide a 100 % bacterial reduction even after 10 repeated washing cycles; and (5) the chemical modification of the cotton fibres did not significantly change their whiteness, wettability or softness.     

Controlled-release of drugs from cross-linked polymers containing cubane as a crosslinking agent

Two anti-inflammatory drugs, indomethacin and aspirin together with cubane-1, 4-dicarboxylic acid (CDA) were covalently linked with 2-hydroxyethyl methacrylate (HEMA). The drug-linked HEMA (indomethacin-linked HEMA) is abbreviated as HI, aspirin-linked HEMA as HA and cubane-1, 4-dicarboxylic acid (CDA) linked to two HEMA group is the cross-linking agent (CA). A difunctional spacer group was introduced between the drugs and acrylic moiety of the monomer through a hydrolyzable ester linkage. Free radical cross-linking polymerization of the monomers with drug effect was carried out in dioxane solution at various CA ratios, using AIBN as initiator in the temperature range 60-70°C. The compositions of the cross-linked three-dimensional polymers were determined by FT-IR spectroscopy. The glass transition temperature (Tg) of the network polymers was determined calorimetrically. The hydrolysis of drug-polymer conjugates was carried out in cellophane membrane dialysis bags containing an aqueous buffer solution (pH 8 and pH 1) at 37°C. Detection of the hydrolysis product by UV spectroscopy shows that the drugs were released by hydrolysis of the ester bond located between the drug and spacer group.     

Enzymatic removal of cellulose from cotton/polyester fabric blends

The production of light-weight polyester fabrics from a polyester/cotton blended fabric, by means of the enzymatic removal of the cellulosic part of the material, was investigated. The removal of cotton from the blended fabric yielded more than 80% of insoluble microfibrillar material by the combined action of high beating effects and cellulase hydrolysis.Other major features of this enzymatic process for converting cotton fibers into microfibrillar material are bath ratio, enzyme dosage and treatment time.     

Reversible crosslinking in cellulose. VII. Memory effect of the crosslinking medium in the dyeing of crosslinked cotton

Cellulose β-mercaptoethylaminocarboxylate made from unmercerized cotton was partially oxidized in various solvents of different swelling power followed by treatment with excess methyl iodide to yield partially disulfide-crosslinked cotton samples of about the same degrees of crosslinking containing sulfonium groups of about the same contents. The effect of the solvent in crosslinking on the equilibrium and kinetics of dyeing with three dyes (Orange II, Direct Scarlet B, and Direct Sky Blue A) of different molecular size was investigated. The 1:1 ionic bonding was observed at equilibrium between sulfonic acid groups in dye molecules and sulfonium groups in modified cottons in cases of Orange II and Direct Scarlet B. The equilibrium uptake of the largest dye, Direct Sky Blue A, was much influenced by the solvent used in crosslinking; the higher the degree of swelling in crosslinking, the larger the equilibrium uptake. The diffusion rate of Direct Scarlet B was much affected by the solvent used; the higher the degree of swelling, the higher the diffusion rate. The pore structure of the crosslinked cotton was discussed. The crosslinked cotton seemed to have a “memory” of the state at the time of crosslinking and to have a tendency to come back close to that state when placed in a dye bath.     

Radiation-induced crosslinking of polyacrylonitrile fibers and the subsequent regulative effect on the preoxidation process

To investigate the radiation effect on polyacrylonitrile (PAN) fibers as well as on the preoxidation process, PAN fibers were irradiated by γ-rays at room temperature at 50–500 kGy in vacuum and then were thermally oxidized in air. Gel fraction determination indicated that γ irradiation led to the predominant crosslinking of PAN fibers, with G values (the number of event per 100 eV absorbed) of G(X)=0.28 and G(S)=0.16 for chain crosslinking and scission, respectively. It was found that irradiation caused a slight change in the crystal structure and tensile strength at low dose. Radiation led to a reduction of the onset temperature of cyclization reaction and moderated the exothermic behavior. The density of the PAN fibers after thermal oxidation was used to evaluate the preoxidation extent. It was proven that radiation could significantly accelerate the preoxidation process and consequently shortened the preoxidation time. Radiation crosslinking may have potential application in the production of PAN-based carbon fibers.     

Investigation of an alternative chemical agent to recover valuable metals from anode slime

Anode slime (AS) including high content of precious metals is a by-product obtained after the electro-refining stage in copper production. In this study, it is aimed to recover Cu, Au, and Ag from the AS by using 1-butyl-3-methyl-imidazolium hydrogen sulphate ([Bmim]HSO₄) ionic liquid (IL) as a green solvent. The effects of IL concentration, temperature, reaction time and pulp density on recovery of valuable metals were statistically investigated. A high copper recovery of 87.52% was obtained under optimum condition as in 60% (v/v) [Bmim]HSO₄ at 50 °C after 2 h, pulp density at 40 g/L (1/25 solid/liquid ratio). Also, a remarkable gold recovery as 97.32% has been achieved in 80% (v/v) [Bmim]HSO₄ at 95 °C after 4 h, pulp density at 40 g/L. Temperature and IL concentration were detected as the most effective parameters for copper and gold recovery from AS, respectively. Silver could not be recovered from the AS due to the lower solubility in [Bmim]HSO₄ IL media. According to experimental results, [Bmim]HSO₄ could be offered as an alternative leaching agent, instead of conventional solvents, to recover valuable metals from copper anode slime.     

Investigation of leaching of an antifouling agent from marine paint formulations using radiotracer technique

A radiotracer technique was used to investigate the leaching of an antifouling agent from different marine paint formulations with an objective to select the best paint formulation for bulk production. The antifouling agent (Diuron) itself was labeled with carbon-14 (half-life: 5,730?years, ??-energy: 156?keV) and used as a radiotracer. The different paint formulations added with radiolabeled Diuron were applied onto suitably selected substrates and measured for initial intensity of ??-radiation using a Geiger-Muller detector connected to a ratemeter. The painted substrates were subjected to shower tests for a pre-decided time and subsequently measured for ??-radiations. The comparison of intensity of ??-radiations in substrates prior and post shower tests provides information about leaching of antifouling agent Diuron from the paint formulation. The high leaching percentage of antifouling agent Diuron post shower tests indicates non-suitability of paint formulation for marine and civil structures. However, low leaching rate of Diuron will make a paint formulation more efficient and suitable. Based on the results of investigation, a paint formulation with minimum leaching rate was identified and selected for bulk production by a paint company.     

Surface chemical analysis of raw cotton fibres and associated materials

The surface chemical composition of raw unscoured cotton was successfully investigated by the surface analytical techniques X-ray Photoelectron Spectroscopy (XPS) and Time of Flight Secondary Ion Mass Spectrometry (ToF-SIMS). The presence of non-cellulosic material at the fibre surface was established and determined to be a complex mixture of fatty acids, alcohols, alkanes, esters and glycerides. The effect of scouring and bleaching was to reduce the surface concentration of these materials but even after aqueous processing some non-cellulosic material residue was still detected at the fibre surface.     

An ultrastructural study of the interaction of a fungal endoglucanase from Humicola insolens with cotton fibres

Because cellulases are finding more applications in the textile and detergent industries, their effect on cotton fibres must be evaluated. For this purpose, the action of a recombinant cellulase, endoglucanase V from the fungus Humicola insolens, has been followed by scanning electron microscopy (SEM) in classical longitudinal views as well as in cross-sections of cotton fibres. The experiments were conducted at large enzyme dilution typical of conditions where cellulases are used for biopolishing, i.e. for the removal of defects created by mechanical abrasion. Endoglucanase V appears to restrict its action to the hydrolysis of the loose fibrils created at the surface of the fibres and no indication of extensive enzyme penetration and damage to the interior of the fibres could be detected by SEM. The adsorption sites for endoglucanase V on cotton fibres were examined by transmission electron microscopy (TEM) on ultrathin cross-sections after immuno-gold labeling of the enzyme. This approach showed that the enzymes did not penetrate the fibres but remained at their surface. The use of an immuno-gold labeled cellulase provides a new way to probe the surface features of cotton fibres This revised version was published online in August 2006 with corrections to the Cover Date.     

Synthesis of statistical networks from liquid polybutadiene—IV. Influence of crosslinking agent

The synthesis of statistical macromolecular networks is achieved from liquid polybutadiene as precursor polymer with difunctional crosslinking agents bearing two hydrogenosilane groups. The properties of the network (extractable polymer, equilibrium swelling degree, uniaxial compression modulus) are strongly influenced by the structure of the crosslinks. Aromatic type structures are best suited to obtain high modulus networks which can be used for applications in the field of composite materials.     

Tailored rheology of a metallocene polyolefin through silane grafting and subsequent silane crosslinking

Polymer modification through silane grafting and its subsequent crosslinking allows the rheological properties of a polymer to be tuned from those of a viscous melt to those of a crosslinked elastic network. In this study, a metallocene polyolefin resin is grafted with vinyl trimethoxy silane (VTMS) using dicumyl peroxide (DCP) as the initiator and is subsequently crosslinked in an oxidative environment. Dynamic rheological experiments are conducted to elucidate the effects of DCP and VTMS concentrations on the grafting and ensuing crosslinking processes. We find that the addition of VTMS alone to the polymer produces no grafting. In contrast, the presence of DCP by itself leads to direct crosslinking between polymer chains as suggested by an increase in elastic modulus and complex viscosity. Samples containing both DCP and VTMS undergo silane grafting, with the extent of grafting increasing with increasing DCP concentration. This conclusion is borne out by both rheological and Fourier transform infrared measurements. The grafted samples undergo silane crosslinking only in an oxidative environment and at temperatures equal to or greater than 190 °C. During crosslinking, the samples undergo a transition from a viscous melt with frequency‐dependent moduli to a gel exhibiting frequency‐independent moduli with the elastic modulus exceeding the viscous modulus. However, the kinetics of crosslinking and the extent of the modulus increase are a function of the DCP concentration, with both exhibiting a maximum at a specific DCP and VTMS combination. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2468–2479, 2000     

Synthesis and characterisation of chiral liquid crystalline elastomers containing four-arm crosslinking agent

A new series of side-chain chiral liquid crystalline elastomers derived from M₁ (cholest-5-3-ol(3β)-4-(2-propen-yloxy)]benzoate) and M_C(2,5-[3,5-bis(4-(3-(4-(allyloxy)phenyl)propanoyloxy)benzoyloxy)benzoic acid]isosorbide diester). The structures of monomers and elastomers measured by using Proton Nuclear Magnetic Resonance Spectra (¹H-NMR) and Fourier transform infrared spectroscopy (FTIR) separately are consistent with our design. IIP~VIP all appeared blue Grandjean (GJ) texture on the heating cycle or cooling cycle. The glass sheets of IIP~VIP were made under 150°C and measured its ultraviolet–visible spectrophotometry by PerkinElmer Lambda 950 instrument (Shelton, CT, USA). IIP~VIP all have absorptions at about 481~483 and 561~562 nm. The optical activities were measured at different temperatures on heating and cooling cycles. And the blue selective reflection of IIP~VIP on the round glass sheet can be seen. The elastomers containing less than 6 mol% of the crosslinking units displayed elasticity, reversible phase transition and high thermal stability. The glass transition temperatures reduced first and then increased, the isotropisation temperatures and the mesophase temperature ranges increased first and then decreased with increasing content of crosslinking unit. The thermogravimetric analysis (TGA) results showed that the temperatures at which 5% weight loss occurred (T_d) were greater than 310°C for all the polymers.     

With radiation crosslinking of engineering plastics into the next millennium

Much basic research has been done on the crosslinking behaviour of so-called “engineering plastics”. Up to now the industrial conversion to actual manufacture of multifunctional electronic components has gained ever increasing importance in the plastics industry and will continue to do so in the coming years. Examples of this are SMD (surface mounted device) technology, and 3D-MID (3-dimensional moulded interconnected devices) technology. These techniques require materials with high short-term temperature stability. In this paper it will be discussed which engineering plastics are significant for the radiation crosslinking process, for both technical and commercial reasons. The main topics will be the crosslinking behaviour of Polybutylenterephthalate (PBT) and Polyamide (PA). The importance and the challenges to the irradiation industry, as well as practical applications, will be shown.     

Thermal hazard identification of crosslinking agent BIBP using DSC test and thermokinetics simulation

Journal of Thermal Analysis and Calorimetry - Bis(tert-butylperoxy isopropyl) benzene peroxide (BIBP) is a popular bridging agent for polymerisation. However, the thermal runaway temperature and...     

Preparation and properties of siloxane liquid crystalline elastomers with a mesogenic crosslinking agent

A mesogenic crosslinking agent M-1 was synthesized to minimize the perturbations of non-mesogenic crosslinking agents in liquid crystalline elastomers. The synthesis of new side chain liquid crystalline elastomers containing the rigid mesogenic crosslinking agent M-1 and nematic monomer M-2 by a one-step hydrosilylation reaction is described. The chemical structures of the monomers and network polymers obtained were confirmed by FTIR and ¹H NMR spectroscopy. The mesomorphic properties and phase behaviour were investigated by differential scanning calorimetry, polarizing optical microscopy, and X-ray diffraction. The influence of the crosslinking units on phase behaviour is discussed. Liquid crystalline elastomers containing less than 15 mol % of the crosslinking units showed elasticity, reversible phase transitions and a threaded texture. The experimental results demonstrated that the glass transition temperature of polymers P-1-7 increased with increasing concentration of crosslinking agent M-1; but the isotropic temperature and liquid crystalline range decreased slightly.