Preparation of Super-Water-Repellent Fluorinated Inorganic-Organic Coating Films on Nylon 66 by the Sol-Gel Method Using Microphase Separation

We have prepared super-water-repellent fluorinated inorganic-organic coating films on nylon 66 substrate from poly(methyl methacrylate) (PMMA), tetraethoxysilane (TEOS), and 2-perfluorooctylethyltriethoxysilane (17F) by the sol-gel method. The contact angle for water of the film was 149°. The fluorinated inorganic-organic film including PMMA particles exhibits the super-water-repellence on nylon 66 and the high ultrasonics-resistance in spite of the low 17F content of the molar ratio of 0.001 per mol of TEOS. The surfaces of the films were characterized by using XPS and SEM in combination with the surface roughness data. It was considered that the fluorinated component was segregated to form separated microphase regions, appropriate surface roughness being resulted to develop high water-repellence.     

Vapor-phase synthesis of mesoporous SiO2-P2O5 thin films

Mesoporous SiO2-P2O5 films were synthesized from the vapor phase onto a silicon substrate. First, a precursor solution of cetyltrimethylammonium bromide (C16TAB), H3PO4, ethanol, and water was deposited on a silicon substrate by a spin-coating method. Then, the C16TAB-H3PO4 composite film was treated with tetraethoxysilane (TEOS) vapor at 90-180 degrees C for 2.5 h. The H3PO4-C16TAB composite formed a hexagonal structure on the silicon substrate before vapor treatment. The TEOS molecules penetrated into the film without a phase transition. The periodic mesostructure of the SiO2-P2O5 films was retained after calcination. The calcined films showed a high proton conductivity of about 0.55 S/cm at room temperature. The molar ratio of P/Si in the SiO2-P2O5 film was as high as 0.43, a level that was not attained by a premixing sol-gel method. The high phosphate group content and the ordered periodic mesostructure contributed to the high proton conductivity.     

Effects of alicyclic moiety incorporation on the properties of polyimide/silica hybrid films

Polyimide (PI)/silica hybrid films were prepared from tetraethyl orthosilicate (TEOS) using a sol‐gel process as well as pyromellitic dianhydride and 4,4‐oxydianiline. 1,4‐Cyclohexanedicarboxylic acid (1,4‐CHDA) was added as a coupling agent. The PI/silica hybrid films were characterized by Fourier transform infrared spectroscopy, field emission scanning electron microscopy, differential scanning calorimetry and wide‐angle X‐ray diffraction. The thermal, tensile and dielectric properties of the hybrid films were measured. The results showed that the tensile and dielectric properties of the hybrid films improved with increasing silica concentration and 1,4‐CHDA content in the PI matrix. Covalent ester bonds were formed between SiOH groups of silica and carboxyl groups of 1,4‐CHDA. As a result, the silica particle size was reduced and dispersed homogeneously in the PI matrix, leading to increased tensile strength and tensile modulus of the typical hybrid film with 1,4‐CHDA (PI‐2), when compared with the PI/silica hybrid film without 1,4‐CHDA at the same silica contents. The presence of an alicyclic moiety containing silica in PI reduced the dielectric constant considerably to 2.83, which was lower than that of pristine PI. Copyright © 2016 John Wiley & Sons, Ltd.     

纳米二氧化硅粒子对聚氯乙烯膜的表面结构及浸润性能的调控作用

报道了一种简便的调控聚合物材料表面结构及浸润性能的方法.利用流延成膜和纳米二氧化硅粒子的印迹修饰作用,制备出3种具有不同表面结构的聚氯乙烯(PVC)膜,膜的浸润性能表现为与水的接触角从103°的疏水性变为65°的亲水性,再改变至130°的疏水性.扫描电镜结果表明印迹修饰后的PVC膜具有纳米和微米尺寸的凹凸表面结构.通过对比实验证实了溶剂氯仿和NaOH溶液并不影响膜表面的疏水性能.     

丙烯酸酯改性水性聚氨酯/纳米二氧化硅复合材料的制备和性能

利用原位聚合伴随溶胶-凝胶进行的过程,合成了丙烯酸酯改性聚氨酯(PUA)/纳米SiO₂(PUAS)复合乳液。 通过纳米粒度仪、扫描电子显微镜、透射电子显微镜和热重分析仪等技术手段表征了复合乳液及胶膜的结构和性能。 结果表明,纳米SiO₂能够均匀地分散在复合材料中,随着原料中前驱体正硅酸乙酯(TEOS)质量分数的增加,复合乳液粒径有所增大,胶膜力学性能和热稳定性明显提高。 当TEOS质量分数为8%,胶膜拉伸强度达到16.8 MPa,邵氏硬度A达到94,最大分解速率温度提高到416 ℃,且胶膜耐水性明显改善,吸水率降低到2.1%。     

Coating and Gas Permeation Properties of Urushiol-Based Organic/Inorganic Hybrid Films

The silica and urushiol based organic/inorganic hybrid was prepared with TEOS and urushiol by sol-gel process. GLYMO, as a silane-coupling agent, was used to obtain crack-free homogeneous films in various molar ratios, and to improve the adhesion between corona-treated BOPP substrate and the coatings. Two kinds of coating solutions were prepared; one was composed of TEOS and urushiol, the other was a mixture of TEOS, GLYMO and urushiol. Urushiol created less cracks on the film in a narrow range of molar ratios. As the amounts of urushiol were increased, the coating solutions quickly became heterogeneous. GLYMO was sufficient to prevent microcracks on the coated film and provided homogeneous coating solution. TEOS/urushiol and TEOS/GLYMO/urushiol coating solution gave insignificant effect on the permeability coefficients of oxygen, nitrogen and carbon dioxide, because the unsaturated alkyl side chain of urushiol might retard the formation of a dense structure between the inorganic silicate and the organic urushiol phase. From the antibacterial test of uncoating PP substrate and the coated film with hybrid solution, the reduction of bacteria of coating film was calculated to be 99.8%.     

Optimization of Ormosil Films for Optical Sensor Applications

Recent work has indicated that Ormosil films, fabricated from organically modified precursors, produce better sensor performance for some specific applications, compared to films fabricated from conventional sol-gel precursors such as TEOS or TMOS. This paper aims to compare film properties and sensor behavior for films fabricated from tetraethoxysilane (TEOS) and tetramethoxysilane (TMOS) silica precursors and both methyltrimethoxysilane (MTMS) and methyltriethoxysilane (MTES) organically modified precursors. Microstructural differences, for example, porosity changes due to the different precursor backbone structures, are interrogated by monitoring oxygen gas and aqueous-phase sensor response. Oxygen sensing using these films is enabled by incorporating in the films an oxygen-sensitive ruthenium dye whose fluorescence is quenched in the presence of oxygen. Film properties such as thickness, thickness stabilization time, as well as sensor response, are discussed in terms of relative hydrolysis and condensation behavior for the different precursors. Film hydrophobicity, an issue which has been identified as being of crucial importance for optimum dissolved oxygen sensor response, is discussed and contact angle measurements are used to investigate the degree of hydrophobicity for different film types. The main motivation for this work is film optimization for optical gas-phase and dissolved oxygen sensors.     

Preparation and characterization of polymer/silica nanocomposites via double in situ miniemulsion polymerization

Polymer/SiO₂ nanocomposite microspheres were prepared by double in situ miniemulsion polymerization in the presence of methyl methacrylate, butyl acrylate, γ‐methacryloxy(propyl) trimethoxysilane, and tetraethoxysilane (TEOS). By taking full advantage of phase separation between the growing polymer particles and TEOS, inorganic/polymer microspheres were fabricated successfully in a one‐step process with the formation of SiO₂ particles and the polymerization of organic monomers taking place simultaneously. The morphology of nanocomposite microspheres and the microstructure, mechanical properties, thermal properties, and optical properties of the nanocomposite films were characterized and discussed. The results showed that hybrid microspheres had a raspberry‐like structure with silica nanoparticles on the shells of polymer. The silica particles of about 20 nm were highly dispersed within the nanocomposite films without aggregations. The transmittance of nanocomposite film was comparable to that of the copolymer film at around 70–80% from 400 to 800 nm. The mechanical properties and the fire‐retardant behavior of the polymer matrix were improved by the incorporation of silica nanoparticles. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3128–3134, 2010     

三甲基氯硅烷对纳米多孔二氧化硅薄膜的修饰

以正硅酸乙酯为先驱体,采用溶胶-凝胶法,结合旋转涂胶、超临界干燥工艺在硅片上制备了纳米多孔SiO2薄膜.用三甲基氯硅烷(TMCS)对该SiO2薄膜进行了表面修饰,采用FTIR、TG-DTA、AFM和椭偏仪等方法研究了TMCS修饰前后薄膜的结构、形貌、厚度与介电常数等性能.超临界干燥后的SiO2薄膜含有Si－O－Si与Si－OR结构,呈疏水性.在空气中250 ℃以上热处理后SiO2薄膜因含有Si－OH而呈吸水性. TMCS修饰后的SiO2薄膜在温度不高于450 ℃时可保持其疏水性和多孔结构. SiO2薄膜经TMCS修饰后基本粒子和孔隙尺寸增大,孔隙率提高,介电常数可降低至2.5以下.     

Controlling the growth of particle size and size distribution of silica nanoparticles by the thin film structure

Nanostructured silicondioxide thin films were prepared by sol–gel spin coating technique. The SiO₂ films were made using a conventional mixture of tetraethoxysilane (TEOS), deionized water and ethanol with various NH₃/TEOS ratios. The nanostructured silica films were made using a mixture of the SiO₂ sol and regular SiO₂ sol to control the enlargement of the particles inside the films. The structural, morphological and optical characterizations of the as-deposited and annealed films were carried out using X-ray diffraction (XRD), atomic force microscopy, scanning electron microscopy, NKD spectrophotometer and ultraviolet–visible (UV–vis) spectroscopy. The transmittance data of the infrared spectra of the films were recorded using an FT-IR Spectrometer. The XRD studies showed that as-deposited films were amorphous and the formation of the alfa-cristobalite phase of the silica film was investigated at annealing temperature close to 1,100 °C. Optical properties of the transmittance spectra in the s and p-polarization modes were collected. Refractive indices and extinction coefficients were determined with respect to the NH₃/TEOS ratios in the compositions of the films. Optical cut-off wavelength values were investigated from the extrapolation of the absorbance spectra which was estimated from the UV–vis spectroscopy measurements. A red shift in the absorption threshold indicated that the size of silica nanoparticles was increased by an increase in the NH₃/TEOS volume ratio from 1:64 to 1:8.     

研究简报聚苯乙烯接枝TiO2有机无机杂化超疏水涂层的制备

采用自由基聚合的方法,在经乙烯基三乙氧基硅烷(VTEOS)修饰的纳米TiO2表面上接枝聚苯乙烯(PS),而后制得PS-g-TiO2有机无机纳米杂化超疏水薄膜。利用场发射扫描电子显微镜和傅里叶变换红外光谱仪对PS-g-TiO2进行了形貌和结构表征,并探讨了VTEOS修饰对TiO2纳米粉体表面浸润性能的影响。测试结果表明,纳米TiO2经VTEOS改性后所制备的PS-g-TiO2薄膜和仅用硅烷偶联剂修饰的TiO2薄膜都具有良好的超疏水性能,水滴在薄膜上的最大静态接触角分别为160°和154°,滑动角分别为3°和4°。     

Mechanically controlled, morphologically determined sol–gel derived UV curable hybrid nanocomposites: SAXS and DMTA studies

This work reports preparation of organic–inorganic hybrid materials by sol–gel method. To this end, UV cured urethane acrylate and different functional monomers were used as organic network together with tetraethyl orthosilicate (TEOS) as inorganic network former and 3-methacryloxy propyltrimethoxy silane (MEMO) as network modifier. The effect of sol–gel precursor’s ratio on morphological properties of hybrid network was studied by small angle X-ray scattering (SAXS). Dynamic mechanical thermal analysis (DMTA) was performed to investigate the mechanical behavior of hybrid films. Whilst hybrids with low content of TEOS and high amounts of MEMO represented a “structural defect”, it was found that by increasing TEOS/MEMO ratio, the silica domain size decreased, showing a mass fractal behavior. This was attributed to a more compact structure of silica and a stronger hybrid network. The changes observed in compactness of hybrid films directly affected the glass transition temperature. By increasing the inorganic phase, more restriction in segmental motion of the polymeric phase occurred. Upon increasing TEOS/MEMO ratio a broader tan δ peak deduced from DMTA graphs was observed, indicating greater phase separation and higher heterogeneity.     

Insight into on-wafer crystallization of pure-silica-zeolite films through nutrient replenishment

Tetraethylorthosilicate (TEOS) is added to a pure-silica-zeolite MEL nanoparticle suspension and the mixture is subsequently used for preparing spin-on low-dielectric constant (low-k) films. The films are then characterized by ellipsometric porosimetry, transmission electron microscopy (TEM), and nanoindentation. Investigation into the film microstructure indicates that the addition of TEOS significantly increases the fraction of the crystalline domains, decreases the inter-crystal mesopore size, and narrows the pore size distribution. Films with 12% TEOS loading have a mean pore size distribution centered at 3.5 nm (diameter) with a full width at half maximum (fwhm) of 0.8 nm, while those with no TEOS have a distribution at 11.1 nm and fwhm of 7.9 nm. At 12% TEOS loading, the reduced modulus and hardness are 11.0 and 1.12 GPa, respectively; without TEOS, the values are 6.4 and 0.57 GPa.     

Surface modification of SPEU films by ozone induced graft copolymerization to improve hemocompatibility

Surface modification of segmented poly(ether urethane) (SPEU) by graft copolymerization with N,N′-dimethyl-N-methacryloyloxyethyl-N-(3-sulfopropyl) ammonium (DMMSA), a zwitterionic sulfobetaine structure, was conducted. A simple two-step procedure for grafting of DMMSA onto the surface of SPEU film was used. The surface was first treated with ozone to introduce active hydroperoxide groups. The active surface was then exposed to the DMMSA solution in the sealed tube. Grafted SPEU film was characterized by ATR–FTIR, XPS and contact angle measurement. ATR–FTIR and XPS investigations confirmed the graft copolymerization. The monomer concentration, copolymerization temperature and time were varied to maximize the efficiency of DMMSA grafting. The equilibrium water content (EWC) and contact angle measurements showed that the hydrophilicity of the film had been greatly improved. The blood compatibility of the grafted films was evaluated by platelet adhesion in platelet rich plasma (PRP), deposits in blood control and protein adsorption in bovine fibrinogen using SPEU film as the control. No platelet adhesion and no thrombus were observed for the grafted films incubated in PRP for 300 min and in blood for 120 min, respectively. The protein adsorption was reduced on the grafted films after incubation in bovine fibrinogen for 120 min. These results proved that improved blood compatibility was obtained by grafting this new zwitterionic sulfobetaine structure monomer onto SPEU film.     

Atomistic simulation of the formation of nanoporous silica films via molecular chemical vapor deposition on nonporous substrates

To distinguish thin deposited film characteristics clearly from the influence of substrate morphological properties, the growth mechanism and the macroscale and nanoscale properties of nanoporous SiO(2) films deposited on nonporous silica (SiO(2)) substrates from chemical precursors Si(OH)(4) and TEOS (tetraethoxysilane) via low-pressure chemical vapor deposition are the primary targets of this study. This work employs a kinetic Monte Carlo (KMC) simulation method coupled to the Metropolis Monte Carlo method to relax the strained silica structure. The influence of the deposition temperature (473, 673, and 873 K) on the properties of the SiO(x) layers is addressed via analysis of the film growth rates, density profiles of the deposited thin films, pore size distributions, carbon depth profiles (with respect to TEOS), and voidage analysis for layers of different thicknesses (8-18 nm). A comparison of simulation with experimental results is also carried out.     

The role of TEOS‐TIP within a pentablock ionomer: Morphology,physical properties,and ion transport

Inorganic–organic nanocomposites were created using tetraethylorthosilicate (TEOS), titanium isopropoxide (TIP), and poly(t‐butylstyrene‐b‐hydrogenated isoprene‐b‐sulfonated styrene‐b‐hydrogenated isoprene‐b‐t‐butylstyrene) or pentablock copolymer (PBC). A TEOS–TIP–H₂O ternary phase diagram was generated to create homogenous sol solutions with designable condensation reactions that led to controllable materials. An inorganic TEOS–TIP network was synthesized using sol–gel chemistry within the organic PBC domain. All TEOS–TIP–PBC films exhibited higher water sorption than unmodified PBC ionomer that was attributed to a change in morphology. Proton conductivity increased up to 80% due to TEOS–TIP within the nanocomposite film. This can be attributed to ion domain redistribution and partial charge transfer from the titanate's inorganic domains to sulfonate groups that promote acid dissociation. PBC had a microphase‐separated morphology that changed with increasing TIP concentration, which was observed from atomic force microscopy and small‐angle X‐ray scattering results. Finally, thermal gravimetric analysis revealed a decrease in degradation temperature, and dynamic mechanical analysis results demonstrated reduced polymer chain mobility caused by inorganic–organic interactions. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 575–586     

Structural and IR Spectroscopic Analysis of Sol-Gel Processed CuFeMnO4 Spinel and CuFeMnO4/Silica Films for Solar Absorbers

Black colored CuFeMnO₄ spinel powders and films were prepared using sol-gel process from Mn-acetate and Fe- and Cu-chloride precursors. Films were deposited by dip-coating technique and heat-treated at 500°C. For CuFeMnO₄/silica films 3-aminopropyl-triethoxysilane (3-APTES) or tetraethoxysilane (TEOS) were used in molar proportion (Mn : Cu : Fe) : silica = 1 : 1. Films and powders were prepared by heating at 500°C. IR spectroscopic measurements were employed to follow the hydrolysis-condensation reactions in (Mn : Cu : Fe)/3-APTES sols hydrolysed with water, and (Mn : Cu : Fe)/TEOS sols hydrolysed with (NH₃)_aq (Stöber processing). The resulting coatings were examined with transmission electron microscopy (TEM) combined with electron dif-fraction analyses, Rutherford back scattering (RBS) and proton induced X-ray emission (PIXE) techniques. Results revealed that (Mn : Cu : Fe)/3-APTES films had a composite structure consisting of the upper Cu_1.4Mn_1.6O₄ spinel and the lower amorphous SiO₂ layer. RBS measurements confirmed the composite structure, showing also that the composition of the film was Mn : Cu : Fe = 1 : 0.96 : 0.29, i.e. close to the precursors ratio Mn : Cu : Fe = 3 : 3 : 1. (Mn : Cu : Fe)/TEOS films prepared from sols which were catalysed with (NH₃)_aq consisted of amorphous monodispersed spherical SiO₂ particles with a size of about 400–420 nm. Solar absorbance (a _s) and thermal emittance (e _T) values of CuFeMnO₄ (500°C) and (Mn : Cu : Fe)/TEOS films (500°C) showed that CuFeMnO₄ films could be used as potential selective coatings for solar absorbers in solar collector systems.     

Surface modification of an ethylene-acrylic acid copolymer film: grafting amine-terminated linear and branched architectures

Polymer films can be tailored for a specific application by modifying their surface properties. In this study, linear and branched architectures were grafted to ethylene-acrylic acid (EAA) copolymer films using the so-called grafting from approach. Dicyclohexylcarbodiimide was used to activate the carboxylic acid functionality on the surface of the EAA copolymer film before reacting it with selected di- and tri-amine compounds. The carboxylic acid functionality was subsequently regenerated by reacting the amine-grafted film with succinic anhydride. These reaction steps were then repeated to create the linear and branched architectures on the EAA film surface. The film surface resulting from each reaction step was analyzed using attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy and contact angle measurements. A systematic analysis of the ATR-FTIR results was performed to estimate the average conversion of the reaction schemes and to explain the observed contact angle results. A significant reduction in water contact angle for the EAA film grafted with a branched architecture was observed. The EAA film grafted with a linear architecture showed a marginal reduction in water contact angle when ethanol was used as a solvent for ethylenediamine. When the solvent for ethylenediamine was changed to water, the contact angle decreased noticeably. However, analysis of control films showed that the reduction in the contact angles was due to the solvent treatment. In the case of branched architectures, such reduction in contact angle due to the solvent treatment was not observed. Several control experiments were performed to ensure that the reduction in the contact angles was in fact due to the grafted species and not due to exposure to various solvents used in the reaction scheme.     

Nano-architectural silica thin films with two-dimensionally connected cagelike pores synthesized from vapor phase

Novel mesostructured silica thin films were prepared on a Si substrate by a vapor-phase synthesis. Vapor of tetraethoxysilane (TEOS) was infiltrated into a surfactant film consisting of a poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) triblock copolymer. Nanophase transition from a lamellar structure to a two-dimensional cage structure of a silica-surfactant nanocomposite was found under vapor infiltration. The rearrangement into the cage structure implies high mobility of the silica-surfactant composites in solid phase. The silica thin films have two-dimensionally connected cagelike mesopores and are isotropic parallel to the film surface. The structure of pores of the films is advantageous for next-generation low-k films. The mesoporous structure has a large lattice parameter d of approximately 102 A, silica layer thickness of approximately 58 A, pillar diameter in the middle of approximately 60 A, pore size of approximately 72 A, BET surface area of approximately 729 m(2)/g, and pore volume of approximately 1.19 cm(3)/g. The films synthesized by the vapor infiltration show a lower concentration of residual Si-OH groups compared to the films prepared by a conventional sol-gel method. The films show high thermal stability up to 900 degrees C and high hydrothermal stability. This method is a simpler process than conventional sol-gel techniques and attractive for mass production of a variety of organic-inorganic composite materials and inorganic porous films.     

含氟高分子/SiO2杂化疏水材料的制备及涂层表面性质

采用自由基溶液聚合与溶胶-凝胶法相结合的方法制备了含氟高分子/SiO2杂化疏水材料.通过甲基丙烯酸十二氟庚酯(FA)与乙烯基三乙氧基硅烷(VTES)共聚合成了含氟硅共聚物(PFAS),进一步通过原硅酸乙酯(TEOS)与PFAS共聚物溶液共水解缩聚制备了具有含氟侧基的碳碳主链高分子和硅氧网络的含氟高分子/SiO2杂化疏水材料.研究结果表明,SiO2组分含量提高可以显著增加杂化材料薄膜的涂敷厚度,改善其耐久性能,而对杂化材料疏水性能的影响不大.