Neutron activation analysis of major and trace elements in crude petroleum

We have determined the concentration of 25 trace elements in crude petroleum from seven Libyan oil fields by instrumental neutron activation analysis. Crude oil samples were irradiated with a thermal neutron dose rate of 10¹² and 10¹³ n·cm^–2·s^–1 in the Tajoura research reactor. The concentration of U, Br, Mg, Cu, Na, V, Cl, Al, Mn and Ca is in a range of 0.015 to 84 ppm and that of sulphur of 0.12 to 1.8%. The elements Sc, Cr, Ni, Fe, Co, Zn, Ag, Se, Sb, Ba, Cs, Yb, Hf and Hg have a concentration range of 0.009 to 8747 ppb. The coefficients of variation are within 10%. The elements V and Ni occur as both porphyrin and non-porphyrin and the ratio of these two forms varies over a wide range. The V/Ni ratios are located between 0.17 and 6.67, which are comparable to the reported values for the crude oils from other countries.     

The determination of tin by carbon filament atomic absorption spectrometry

The atomic absorption characteristics of tin on a carbon filament atom reservoir are described. The behaviour of tin in aqueous solution astin(II) chloride, in xylene as tin octoate and in oil solutions is studied. The interferenceeffects of a selected range of seven cations, added as chlorides in aqueous solution or as naphthenates in non-aqueous media, and of sulphate and phosphate were examined. In all cases, the signals were measured in the filament reservoir with a surrounding hydrogen diffusion flame. The 1% absorption sensitivity in the organic media at the 286.3-nm line was 10^-10 g and 9·10^-11 g in aqueous solution. In the latter medium, the corresponding sensitivity at 224.6 nm was 6.7·10^-11 g. The linear analytical range lay in the region 0 to 20 ng.     

Determination of vanadium in petroleum crudes and fuel oils by gas chromatography

A method is described for determining levels of vanadium as low as 0.1 μg g^-1 in petroleum oils by gas chromatography with flame-ionization detection. The method involves decomposition of the oils, derivatization and solvent extraction of vanadium as the chelate, [2,2,2',2'-tetramethyl-5,5'-(ethane-1,2-diyldiimino)bis(hex-4-en-3-onato)-(2-)] oxovanadium(IV), followed by gas chromatography on a non-polar (SE-30) column. The procedure is applied to a variety of samples, including standard reference and fuel oils used in an interlaboratory study. The results are compared with those of emission spectrography and two standard methods. The new procedure can be extended to the selective, simultaneous detection of copper, nickel and vanadium in such samples.     

Method development for the determination of nickel in petroleum using line-source and high-resolution continuum-source graphite furnace atomic absorption spectrometry

Several sample preparation methods have been investigated for the direct determination of nickel in crude oil using graphite furnace atomic absorption spectrometry (GF AAS). Xylene was found unsuitable as solvent because of the poor long-term stability of the solutions and the resulting contamination of the equipment. Isobutyl methyl ketone (IBMK) solutions exhibited better stability, but the sensitivity of the organic nickel salt used for the standard solutions showed a high day-to-day variability. An oil-in-water emulsion using Triton X-100 as surfactant gave the best results. Using high-resolution continuum-source (HR-CS) GF AAS, it could be observed that up to 50% of the nickel in crude oil, most likely low molecular weight nickel porphyrins, were lost already at pyrolysis temperatures >400 °C, whereas the rest of the nickel as well as the nickel standard were stable up to 1300 °C. The nickel absorption at a secondary line at 232.138 nm was recorded simultaneously with that at the primary line at 232.003 nm, expanding the dynamic working range by an order of magnitude. The best characteristic mass obtained was m₀=27 pg and the limit of detection was around 0.07 μg g⁻¹ Ni in oil, based on an emulsion of 2 g oil in 10 ml. The accuracy of the procedure was verified by analyzing the certified reference material (CRM) NIST SRM 1634c, Trace Metals in Residual Fuel Oil.     

Phase behaviour of heavy petroleum fractions in pure propane and n-butane and with methanol as co-solvent

This work reports phase equilibrium experimental results for heavy petroleum fractions in pure propane and n-butane as primary solvents and using methanol as co-solvent. Three kinds of oils were investigated from Marlim petroleum: a relatively light fraction coming from the first distillation of crude petroleum at atmospheric pressure (GOP – heavy gas oil of petroleum), the residue of such distillation (RAT) and the crude petroleum sample. Phase equilibrium measurements were performed in a high-pressure, variable-volume view cell, following the static synthetic method, over the temperature range of 323 K to 393 K, pressures up to 10 MPa and overall compositions of heavy component varying from 1 wt% to 40 wt%. Transition pressures for low methanol and oil concentrations were very close for GOP, RAT, and crude Marlim when using propane as the primary solvent. Close to propane critical temperature, two and three-phase transitions were observed for GOP and Marlim when methanol was increased. When n-butane was used as primary solvent, all transitions observed were of (vapour + liquid) type with transition pressure values smaller than those obtained for propane.     

The development of a method for the qualitative and quantitative determination of petroleum hydrocarbon components using thin-layer chromatography with flame ionization detection

An analytical scheme to determine groups of petroleum hydrocarbon compounds in crude oil was developed and used for the qualitative and quantitative characterization of crude oil samples from the Shengli oilfield, the second largest oilfield in China. Crude oil samples were fractionated and analyzed by thin-layer chromatography with flame ionization detection (TLC-FID). Relative standard deviation (RSD) values for retention time, peak height and half peak width were less than 5.2% for all classes of compounds, based on nine independent replicates. The crude oil light fraction was further analyzed by GC–MS and the majority of identified compounds were methyl- or hydro-derivatives of long-chain hydrocarbons and aromatic compounds. The external standard method used in the present study can lower detection limits of petroleum hydrocarbon compound classes to 20.0 mg L⁻¹, and the crude oil concentration in the range of 30 and 35,000 mg L⁻¹ has a high linear correlation (r² > 0.97, P < 0.05) with peak area. A comparison between elution chromatography (EC) and TLC-FID regarding the recovery of petroleum hydrocarbon compounds was carried out with aged crude oil contaminated soils of 50, 80, 200 and 300 mg g⁻¹. The tested TLC-FID method showed a 10% higher recovery for total extractable materials than the reference EC method. The calibration factor was fraction-dependent and varied with the recovery rate of TLC/EC. Regarding the tested extraction procedures, accelerated solvent extraction (ASE) had a higher extraction efficiency for crude oil contaminated soils than Soxhlet and ultrasonic extractions.     

Determination of lead in waters by atomic absorption spectrometry with electrothermal atomization

Summary The electrothermal atomization of lead has been investigated for accurate determination of lead in water samples. Thiourea served to lower the atomization temperature of lead and to eliminate the interferences from chloride matrix. The addition of thiourea also allowed the accurate determination of lead irrespective of its chemical form. The absolute sensitivity (1% absorption) was 1.1 × 10^–12g of lead. The method permits the direct rapid determination of lead in water samples including sea water.

---

Bestimmung von Blei in Wässern durch Atomabsorptions-Spektrometrie mit elektrothermischer Atomisierung

Zusammenfassung Zur Verringerung der Atomisie-rungstemperatur und zur Beseitigung von Störungen durch die Chloridmatrix wird ein Zusatz von Thioharnstoff empfohlen. Dieser Zusatz gestattet außerdem eine genaue Bestimmung unabhängig von der chemischen Form, in der das Blei vorliegt. Die absolute Empfindlichkeit (1% Absorption) beträgt 1,1 · 10^–12 g Pb. Das Verfahren wurde zur direkten Bleibestimmung in Wässern, einschl. Meereswasser, angewendet.

     

Development of a species-specific isotope dilution GC-ICP-MS method for the determination of thiophene derivates in petroleum products

A species-specific isotope dilution technique for accurate determination of sulfur species in low- and high-boiling petroleum products was developed by coupling capillary gas chromatography with quadrupole ICP-MS (GC-ICP-IDMS). For the isotope dilution step ³⁴S-labeled thiophene, dibenzothiophene, and mixed dibenzothiophene/4-methyldibenzothiophene spike compounds were synthesized on the milligram scale from elemental ³⁴S-enriched sulfur. Thiophene was determined in gasoline, ‘sulfur-free’ gasoline, and naphtha. By analyzing reference material NIST SRM 2296, the accuracy of species-specific GC-ICP-IDMS was demonstrated by an excellent agreement with the certified value. The detection limit is always limited by the background noise of the isotope chromatograms and was determined for thiophene to be 7 pg absolute, which corresponds to 7 ng sulfur/g sample under the experimental conditions used. Dibenzothiophene and 4-methyldibenzothiophene were determined in different high-boiling petroleum products like gas oil, diesel fuel, and heating oil. In this case a large concentration range from about < 0.04 to more than 2,000 μg g⁻¹ was covered for both sulfur species. By parallel GC-ICP-MS and GC-EI-MS experiments (EI-MS electron impact ionization mass spectrometry) the substantial influence of co-eluting hydrocarbons on the ICP-MS sulfur signal was demonstrated, which can significantly affect results obtained by external calibration but not those by the isotope dilution technique.     

Evaluation of clean-up agents for total petroleum hydrocarbon analysis in biota and sediments

Petroleum hydrocarbons (oil) are common environmental contaminants. For risk assessment purposes, their concentrations in environmental matrixes, such as biota and soils/sediments are frequently determined by solvent extraction and subsequent analysis with gas chromatography (GC) equipped with flame ionization detection (FID) or mass spectrometry (MS). Because the total GC detector response is labeled as total petroleum hydrocarbon (TPH) concentration and matrix compounds (lipids, organic matter) will contribute to this response, proper extract clean-up is crucial. Still, the choice for a specific clean-up material during open column chromatography often seems arbitrary, since no comparative study on clean-up agents for TPH analysis is available. Here, such a study is described and it is demonstrated that none of the commonly used agents fulfills the requirements of complete matrix compound removal and TPH recovery. A novel column filled with (top-down) 1 g of 33% (w/w) 1 M NaOH-impregnated and 2.2 g of 7% (w/w) H₂SO₄-impregnated silica gel is recommended for cleaning-up biota extracts, as it fully removes extracted lipids and yields acceptable TPH recoveries of around 90%, based on a certified oil reference standard. For sediment extracts, most columns tested resulted in a negligibly low contribution of matrix compounds to the overall detector response, but 5% deactivated Florisil or 10% deactivated aluminum oxide are preferable, because these materials yield the highest (∼95%) TPH recoveries.     

Sulfur trace determination in petroleum products by isotope dilution ICP-MS using direct injection by thermal vaporization (TV-ICP-IDMS)

An accurate, sensitive, and fast method for direct determination of total sulfur in petroleum products after thermal vaporization of an isotope-diluted sample was developed by using ICP-MS. ³⁴S-labelled dibenzothiophene spike was used for the isotope dilution step. The isotope-diluted sample was injected into a thermal vaporizer which was directly connected by a heated transfer line to the plasma torch. Sample transport was achieved by using a helium gas flow, and the isotope ratio ³⁴S/³²S was determined within seconds after injection. No other sample preparation other than the simple and fast isotope dilution step, which enables accurate and sensitive determination of sulfur at high sample throughputs, is necessary. Thus, this technique fits all needs for routine analyses. Validation of the TV-ICP-IDMS method was carried out by analyzing the certified gas oil reference materials BCR672 and BCR107. Comparison of results for noncertified low- and high-boiling samples, obtained from an ICP-IDMS microwave-assisted digestion method, also resulted in very good agreement. The low detection limit of 40 ng/g and the large dynamic range of TV-ICP-IDMS fulfill all necessities to allow analysis of sulfur in different petroleum products, e.g., even at the low concentration level of ‘sulfur-free’ gasoline.     

Zur emissionsspektralanalytischen Bestimmung von Cu-, Fe- und Pb-Spuren in ZnS-Leuchtstoffen

Zusammenfassung Eine emissionsspektralanalytische Methode wird beschrieben, mit deren Hilfe 3 · 10^–7 bis 3 · 10^–5 g Fe, 2 · 10^–6 bis 3,2 · 10^–6 g Pb und 3 · 10^–8 bis 1 · 10^–5 g Cu pro g ZnS bestimmt werden können.

---

Summary An emission spectral analytical method is described by which 3 · 10^–7 to 3 · 10^–5 g iron, 2 · 10^–6 3.2 · 10^–5 g lead, and 3 · 10^–8–1 · 10^–5 g copper per g ZnS can be determined.

---

Résumé On décrit une méthode d'analyse spectrale par émission permettant de doser 3 · 10^–7–3 · 10^–5 g Fe, 2 · 10^–6–3,2 · 10^–5 g Pb et 3 · 10^–8–1 · 10^–5g Cu par g ZnS.

---

---

Herrn Prof. Dr.A. A. Benedetti-Pichler zum 70. Geburtstag gewidmet. Vorgetragen am XI. Colloquium Spectroacopicum Internationale, Beograd, 1963.

---

Wir danken auch an dieser Stelle HerrnP. Endröi für die Zubereitung der Standards mit Cu- und Fe-Zusatz und Herrn DirektorF. Kömüves für die Erlaubnis zur Publikation dieser Arbeit.     

Instrumental neutron activation analysis of sediment reference materials using the k0-standardization method

An instrumental neutron activation analysis technique has been developed for the determination of As, Au, Ba, Co, Cr, Fe, Hf, Sb, Ta, Th, U, W and Zn in large (10–15 g) geological samples using in-pool irradiation with a SLOWPOKE-2 reactor. The technique allows for the simultaneous irradiation of multiple samples using a neutron flux of between 4·10¹³ and 8·10¹³ n·m^–2·s^–1. The detection limits obtained using the analytical methodology described in this paper are acceptable for exploration geochemistry and the technique has been used to analyze samples collected as part of a metallic minerals survey of Jamaica.     

Sample preparation in the determination of metals in oil and petroleum products by ICP MS

Comparative elemental analysis of the Tengiz oil and diesel fuel is performed by inductively coupled plasma mass-spectrometry with autoclave digestion, digestion, dilution with organic solvents, and also rotating coiled columns (RCCs). The advantages and drawbacks of each of the listed sample preparation techniques for the separation of microelements are discussed. In contrast to the other versions, the use of RCCs is shown to provide a unique opportunity to preconcentrating microelements from oil and petroleum products into tiny volumes of aqueous solutions (10 mL of 0.5 M HNO₃). The eluate prepared can be used in the subsequent analysis by ICP MS with no extra sample preparation steps. The RCC preconcentration of elements from oil and petroleum products makes it possible to determine metals in concentrations from μg/kg to ng/kg.     

Prompt gamma neutron activation analysis of boron with a 241Am-Be neutron source

A prompt gamma neutron activation analysis (PGAA) setup installed at ANRTC has been used to analyze boron. It consists of a 22.6% REGe detector and a 740 GBq ²⁴¹Am-Be neutron source moderated with water and paraffin. At the sample irradiation position, the thermal neutron fluence rate measured was 2.36·10⁴ n·m^–2· s^–1 and the corresponding Cd-ratio was 22 for gold monitor. The absolute detection efficiency in the range of 120–1500 keV was determined using ¹⁵²Eu standard solution. The sensitivity and detection limit for standard boric acid samples has been determined. The boron content in boric acid prepared from Turkish borate ores is measured to be 15.91±0.46% wt.     

Prompt gamma neutron activation analysis of boron with a 241Am-Be neutron source

A prompt gamma neutron activation analysis (PGAA) setup installed at ANRTC has been used to analyze boron. It consists of a 22.6% REGe detector and a 740 GBq ²⁴¹Am-Be neutron source moderated with water and paraffin. At the sample irradiation position, the thermal neutron fluence rate measured was 2.36·10⁴ n·m^–2· s^–1 and the corresponding Cd-ratio was 22 for gold monitor. The absolute detection efficiency in the range of 120–1500 keV was determined using ¹⁵²Eu standard solution. The sensitivity and detection limit for standard boric acid samples has been determined. The boron content in boric acid prepared from Turkish borate ores is measured to be 15.91±0.46% wt.     

A gas-jet system for the study of short-lived,light fission products

A selective method for the solvent extraction and spectrophotometric determination of uranium(VI) is described. Uranium can be extracted into chloroform at pH 6.0 with N-m-chlorophenyl-2-theno-hydroxamic acid (N-m-CPTHA) and determined by spectrophotometry using 1-(2-pyridylazo)-2-naphthol (PAN). The molar absorptivity is 1.50·10⁴ 1·mol^–1·cm^–1 at 560 nm. The system obeys Beer's law within the range 0.95–20.00 ppm of uranium. Alternatively, a back-extraction procedure was also developed in which uranium is back-extracted by nitric acid and estimated spectrophotometrically using Arsenazo III. The molar absorptivity is 2.0·10⁴ 1·mol^–1·cm^–1 at 665 nm. The parameters concerning the optimum conditions for the analytical method are discussed. The proposed method is applied precisely for the determination of uranium in rock and sea water samples.     

Nitrate ion transport across TBP-kerosene oil supported liquid membranes coupled with uranyl ions

The role of nitrate ions in uranyl ions transport across TBP-kerosene oil supported liquid membranes (SLM) at varied concentrations of HNO₃ and NaNO₃ has been studied. It has been found that nitrate ions move faster compared to uranyl ions at the uranium feed solution concentrations studied. The nitrate to uranyl ions flux ratio vary from 355 to 2636 under different chemical conditions. At low uranium concentration the nitrate ions transport as HNO₃ · TBP, in addition to as UO₂(NO₃)₂ · 2TBP type complex species. The flux of nitrate ions is of the order of 12.10 · 10^–3 mol · m^–2 · s^–1 compared to that of uranium ions (4.56 · 10^–6 mol · m^–2 · s^–1). The permeability coefficient of the membrane for nitrate ions varies with chemical composition of the feed solution and is in the order of 2.5 · 10^–10 m^–2 · s^–1. The data is useful to estimate the nitrate ions required to move a given amount of uranyl ions across such an SLM and in simple solvent extraction.     

Extraction studies of thorium(IV) with triphenylphosphine oxide

A simple method is described for the solvent extraction of thorium. Thorium is extracted quantitatively from 5·10^–3M sodium salicylate solution at pH 2.5–3.25 using 2.16·10^–2M triphenylphosphine oxide as an extractant dissolved in toluene. The extracted metal ion is stripped with hydrochloric acid (0.1M) and determined spectrophotometrically with Thoron-1 at 540 nm. The method permits separation of thorium from lanthanum, cerium, neodymium, samarium and uranium from binary mixtures and is applicable to the analysis of monazite sand. The method is precise, accurate and selective.     

Spectrophotometric determination of beryllium and zirconium using chromotrope-2C

Summary Disodium salt of o-carboxyphenylazo chromotropic acid (chromotrope 2C) has been used for the colorimetric determination of microamounts of beryllium and zirconium. The red-violet complexes show maximum absorption at 580 nm and the colour systems obey Beer's law from 0.025 to 0.375 ppm of beryllium and 2 to 12 ppm of zirconium. The optimum concentration ranges are from 0.125 to 0.375 ppm for beryllium and from 4 to 12 ppm for zirconium, where the percent relative errors per 1% absolute photometric error are, respectively, 3.014 and 3.22. The sensitivity of the reactions per cm² are 0.00067 g Be and 0.027 g Zr. The complexes, with the metal to reagent ratio of 11, have instability constants as 2.836 · 10^–6 for beryllium and 6.026 · 10^–6 for zirconium.     

5-(4-Carboxylphenylazo)-8-aminoquinoline as an analytical reagent for the spectrophotometric determination of gold

The synthesis and analytical application of 5-(4-carboxylphenylazo)-8-aminoquinoline (CPAQ) are described. A simple, rapid, selective, and sensitive spectrophotometric method for the determination of microgram amounts of gold is developed, based on the colour reaction between the metal ion and CPAQ in the presence of cetyltrimethyl ammonium bromide. Gold (III) reacts with the reagent in the ratio 1 3 (metal to ligand) in alkaline solution to form a blue-green complex with an absorption maximum at 608 nm. Beer's law is obeyed over the concentration range 0–1.8 g · ml^–1 (ppm) of gold. The molar absorptivity and Sandell's sensitivity of the method are 9.11 × 10⁴ l · mole^–1 · cm^–1 and 0.00216 g · cm^–2, respectively. The interference of various ions has been studied and conditions were developed for the determination of gold in an ore and anode slimes.