Magnetization of sol-gel prepared zinc ferrite nanoparticles: Effects of inversion and particle size

Nanoparticles of ZnFe₂O₄ have been prepared by using sol-gel method in two different mediums (acidic and basic) in order to observe the influence of the medium on the magnetic properties of the obtained nanoparticles. X-ray diffraction and Mössbauer studies of these samples show the presence of single-phase spinel structure. The average size of the particles as determined by X-ray diffraction increases with the annealing temperature from 18 to 52 nm. With the increase in particle size, magnetization decreases while the magnetization blocking temperature increases. Magnetization studies show that the samples prepared in basic medium have more ferrimagnetic nature as compared to those prepared in acidic medium. We understand this increase in magnetization as reflective of the increased degree of inversion (transfer of Fe³⁺ ions from octahedral to tetrahedral sites) in the particles of smaller size unit cells. From lattice parameter calculations on different particles it is determined that inversion is more favorable in the particles prepared in a basic medium than in the acidic medium due to the smaller cell size in the former.     

Effects of particle size and laser wavelength on heating of silver nanoparticles under laser irradiation in liquid

Laser energy absorption results in significant heating of metallic nanoparticles and controlling the heating of nanoparticles is one of the essential stages of selective cell targeting. It is necessary to note that the laser action should be done by laser pulses with a wavelength that is strongly absorbed by the particles and it is important to select wavelengths that are not absorbed by the medium. Laser pulse duration must be chosen sufficiently short to minimize heat flow emitted from absorbing particles. Numerical calculations based on Mie theory were used to obtain the effect of laser wavelength and particle size on absorption factor for colloidal silver nanoparticles with radii between 5 and 50 nm. Calculations for acquiring temperatures under irradiations of pulsed KrF laser and pulsed Nd:YAG laser were performed. We showed that for low wavelengths of the laser, smaller nanoparticles have larger absorption efficiency compared to larger nanoparticles and in high wavelengths, temperature of all particles increased in the same way.     

Stability, size and optical properties of silver nanoparticles prepared by laser ablation in different carrier media

We studied the effects of the surrounding liquid environment on the size and optical properties of silver nanoparticles prepared by laser ablation by a pulsed Nd:YAG laser operated at 1064 nm. The silver targets used were kept in acetone, water and ethanol. TEM observations and optical extinction were employed for characterization of particle size, shape and optical properties, respectively. Nano silver in acetone showed a narrow size distribution with a mean size of 5 nm and the colloidal solution was stable. In deionised water a rather narrow size distribution with a mean size of 13 nm was observed and nanoparticles were precipitated slowly after about two weeks. In ethanol, a broadening in size distribution and optical extinction spectra was observed. Silver nanoparticles in ethanol with a mean size of 22 nm were completely precipitated after 48 h. In acetone, deionised water and ethanol, the wavelengths of maximum optical extinction are 399, 405 and 411 nm respectively, which is attributed to increasing the size of the nanoparticles. Growth, aggregation and precipitation mechanisms were related to the dipole moment of the surrounding molecules in order to clarify the difference in size, optical properties and stability of the nanoparticles. PACS 79.20.Ds; 81.07.-b; 61.46.+w     

Soot particle size distributions in a well-stirred reactor/plug flow reactor

A well-stirred reactor (WSR) followed by a plug flow reactor (PFR) is being used to study polycyclic aromatic hydrocarbon (PAH) growth and soot inception. Soot size distributions were measured using a dilution probe followed by a nano-differential mobility analyzer (Nano-DMA). A rapid insertion probe was fabricated to thermophoretically collect particles from the reactor for transmission electron microscopy (TEM) imaging. Results are presented on the effect of equivalence ratio on the soot size distributions obtained for fixed dilution ratio, the effect of dilution ratio on the soot size distributions obtained for fixed equivalence ratio, and the effect of temperature on the soot size distributions obtained for fixed equivalence ratio. In addition to particle sizing measurements, gas samples were analyzed by a gas chromatograph to determine the concentration of gaseous species in the PFR thought to be important in soot formation. Our soot size distribution measurements demonstrate that the mixing conditions in the flame zone affect whether or not a nucleation mode was detected in the size distribution.     

Effects of particle size on the structural and hyperfine properties of tin dioxide nanoparticles

In this work, we report on the study of SnO ₂ nanoparticles prepared by a polymer precursor method. X-ray diffraction (XRD) data analysis evidenced the formation of only the tetragonal rutile-type phase for the as-grown and thermally annealed samples. A mean grain size of about 11 nm for the as-prepared sample has been determined. This mean size increases after the thermal annealing and with the annealing temperature. The room temperature M?ssbauer spectra (MS) were well fitted using a quadrupole splitting (QS) distribution. The isomer shift (IS) tends to increase when the grain size decreases. That increase has been associated to the extra s-electron density generated by the oxygen vacancies.     

SERS activity of carbon nanotubes modified by silver nanoparticles with different particle sizes

A two-dimensional (2D) surface-enhanced Raman scattering (SERS) substrate is fabricated by decorating carbon nanotube (CNT) films with Ag nanoparticles (AgNPs) in different sizes, via simple and low-cost chemical reduction method and self-assembling method. The change of Raman and SERS activity of carbon nanotubes/Ag nanoparticles (CNTs/AgNPs) composites with varying size of AgNPs are investigated by using rhodamine 6G (R6G) as a probe molecule. Meanwhile, the scattering cross section of AgNPs and the distribution of electric field of CNTs/AgNPs composite are simulated through finite difference time domain (FDTD) method. Surface plasmon resonance (SPR) wavelength is redshifted as the size of AgNPs increases, and the intensity of SERS and electric field increase with AgNPs size increasing. The experiment and simulation results show a Raman scattering enhancement factor (EF) of 10⁸ for the hybrid substrate.     

Aerosol flow in a tube furnace reactor of gas-phase synthesised silver nanoparticles

In a previous work, gas-phase synthesis of silver nanoparticles through evaporation of silver powder and subsequent particle nucleation by cooling was shown to be a viable method for achieving high purity silver nanoparticles (Backman et al. J Nanopart Res 4:325–335, 2002). In order to control the size of the produced nanoparticles, careful design of the reactor is required with respect to thermal and flow characteristics. In the present work, the silver nanoparticle reactor is rigorously simulated by means of multidimensional computational fluid and particle dynamics. The CFD-computed flow is input for a combined simulation of the vapour field and particle homogeneous nucleation, growth and coagulation. The results are compared with the experimental data and with the predictions from the usually employed simple model of an idealized plug flow reactor. The multidimensional CFD-based analysis is shown to explain and help understand different aspects of the reactor operation and size distribution of the particles produced. Yet the simple plug flow method is found to provide reasonable accuracy when an appropriate correction factor is used for the nucleation rate. Considering its robustness and computational simplicity, the plug flow method can be qualified as adequate from the engineering practical point of view for the case of silver nanoparticle reactors.     

Enzyme-induced growth of silver nanoparticles studied on single particle level

Based on their interesting properties, metal nanoparticles show the potential as an analytical tool in electronic (Burmeister et al. 2004), optical (Yguerabide and Yguerabide 1998), and catalytic applications (Liu 2006). Their characteristics depend on the composition, shape, and size of the single particles. These various properties are utilized in many different approaches such as optics, magnetics (Lang et al. 2007), and laser technology (Csaki et al. 2007). We investigated an alternative method for the synthesis of nanoparticles. In this case, an enzyme, horseradish peroxidase, induces a silver deposition and replaces a metal nanoparticle as the reaction seed. Depending on the reaction time, we could obtain particles in a range of few nanometers up to more than 250 nm. For a better understanding of the enzymatic silver deposition process, the silver particles produced by this process were analyzed by SEM, TEM, and atomic force microscopy (AFM) on a single particle level after different enhancement times. The AFM images were utilized for the characterization of particle height and volume to study the enzyme kinetics, i.e., the particle growth process. Thereby, two different phases are described: a first growth phase probably induced by the enzyme-related growth, and a second, more unspecific growth based on the metal deposition onto the silver deposits. These findings may help to use the enzyme-induced silver deposition in a quantitative manner for bioanalytical applications.     

Controlled synthesis of colloidal silver nanoparticles in capillary micro-flow reactor

In this study, using a polytetrafluoroethylene (PTFE) capillary tube as a micro-flow reactor, well-dispersed colloidal silver nanoparticles were controllably synthesized with different flow rates of precursory solution. Scanning transmission electron microscopy images and UV–visible absorbance spectra showed that silver nanoparticles with large size can be prepared with slow flow rate in the PTFE capillary reactor. The effects of tube diameters on the growth of colloidal silver nanoparticles were investigated. Experiment results demonstrated that using tube with small diameter was more propitious for the controllable synthesis of silver nanoparticles with different sizes.

     

Uptake of silver nanoparticles by monocytic THP-1 cells depends on particle size and presence of serum proteins

Human health risks by silver nanoparticle (AgNP) exposure are likely to increase due to the increasing number of NP-containing products and demonstrated adverse effects in various cell lines. Unfortunately, results from (toxicity) studies are often based on exposure dose and are often measured only at a fixed time point. NP uptake kinetics and the time-dependent internal cellular concentration are often not considered. Macrophages are the first line of defense against invading foreign agents including NPs. How macrophages deal with the particles is essential for potential toxicity of the NPs. However, there is a considerable lack of uptake studies of particles in the nanometer range and macrophage-like cells. Therefore, uptake rates were determined over 24 h for three different AgNPs sizes (20, 50 and 75 nm) in medium with and without fetal calf serum. Non-toxic concentrations of 10 ng Ag/mL for monocytic THP-1 cells, representing realistic exposure concentration for short-term exposures, were chosen. The uptake of Ag was higher in medium without fetal calf serum and showed increasing uptake for decreasing NP sizes, both on NP mass and on number basis. Internal cellular concentrations reached roughly 32/10 %, 25/18 % and 21/15 % of the nominal concentration in the absence of fetal calf serum/with fetal calf serum for 20-, 50- and 75-nm NPs, respectively. Our research shows that uptake kinetics in macrophages differ for various NP sizes. To increase the understanding of the mechanism of NP toxicity in cells, the process of uptake (timing) should be considered.     

The effect of the deposition parameters on size, distribution and antimicrobial properties of photoinduced silver nanoparticles on titania coatings

Controlled photodeposition of silver nanoparticles (AgNP) on titania coatings using two different sources of UV light is described. Titania (anatase) thin films were prepared by the sol-gel dip-coating method on silicon wafers. AgNPs were grown on the titania surface as a result of UV illumination of titania films immersed in aqueous solutions of silver nitrate. UV xenon lamp or excimer laser, both operating at the wavelength 351 ± 5 nm, was used as illumination sources. The AFM topography of AgNP/TiO₂ nanocomposites revealed that silver nanoparticles could be synthesized by both sources of illumination, however the photocatalysis carried out by UV light from xenon lamp illumination leads to larger AgNP than those synthesized using the laser beam. It was found that the increasing concentration of silver ions in the initial solution increases the number of Ag nanoparticles on the titania surface, while longer time of irradiation results the growth of larger size nanoparticles. Antibacterial tests performed on TiO₂ covered by Ag nanoparticles revealed that increasing density of nanoparticles enhances the inhibition of bacterial growth. It was also found that antibacterial activity drops by only 10-15% after 6 cycles compared to the initial use.     

The effect of particle size on the characteristics of FeCo nanoparticles

Some size-dependent characteristics of FeCo nanoparticles are investigated in this paper. The nanoparticles are fabricated using a coprecipitation route and their sizes are controlled by changing the reaction time. Transverse electron microscopy (TEM) images show that the nanoparticles are all spherical with an average size of 2–6 nm. The average size obtained from X-ray diffraction (XRD) measurements is in the range 1–3 nm. Magnetic measurements reveal that the nanoparticles are ordered ferromagnetically and have a high coercivity of about 500 Oe. In our measurements, the coercivity was decreased with decreasing particle size, indicating that the nanoparticles were in a single-domain region. Production of FeCo nanoparticles with high coercivity and fine dimension is highly promising for future recording media technology.     

Light absorption measurement of a plasmonic photocatalyst in the circular plane waveguide of a photocatalytic dual light source spinning disk reactor

This study numerically investigates the light absorption of a plasmonic photocatalyst in the circular plane waveguide of a photocatalytic spinning disk reactor. The degradation of methyl orange (MO) in water with a dual light source spinning disk reactor (DL-SDR) and embedded diffusion coupler demonstrates the plasmonic photocatalytic reaction. When light propagates in the circular plane disk (CPD) waveguide of a DL-SDR, it gradually loses energy because of the absorption of the photocatalyst. This absorption boosts the processing efficiency of the plasmonic photocatalytic reaction. A real case by a diffusion coupler was used to present the plasmonic photocatalytic reaction. This study presents the numerical analysis of a secondary optical lens (SOL) coupler and the numerical evaluation of light absorption of the plasmonic photocatalyst in a DL-SDR. An elliptical reflector collects the light emitted from the circular ring edge of the SOL and CPD. This study presents an evaluation method that simulates the light absorption of a photocatalyst coating on the CPD of a DL-SDR.     

Electrospinning method for the preparation of silver chloride nanoparticles in PVP nanofiber

It has been successfully developed by the electrospinning technology that AgCl nanoparticles were incorporated into polymer fiber. In this paper, we chose poly(vinyl pyrrolidone) (PVP) because it was not only a good material for electrospinning but also it was excellent capping reagent of various metal nanoparticles. The silver ions interacted with the carbonyl groups in the PVP molecules. The formation of AgCl nanoparticles inside the PVP were carried out via the reaction of silver ions and HCl. TEM proved that most of the AgCl nanoparticles were uniformly dispersed in the PVP fibers.     

Characterization and antimicrobial activity of silver nanoparticles prepared by a thermal decomposition technique

Recently, there has been an increasing need of efficient synthetic protocols using eco-friendly conditions including low costs and green chemicals for production of metal nanoparticles. In this work, silver nanoparticles (silver NPs) with average particle size about 10 nm were synthesized by using a thermal decomposition technique. Unlike the colloidal chemistry method, the thermal decomposition method developed has advantages such as the high crystallinity, single-reaction synthesis, and easy dispersion ability of the synthesized NPs in organic solvents. In a modified synthesis process, we used sodium oleate as a capping agent to modify the surface of silver NPs because the oleate has a C₁₈ tail with a double bond in the middle, therefore, forming a kink which is to be effective for aggregative stability. Importantly, the as-synthesized silver NPs have demonstrated strong antimicrobial effects against various bacteria and fungi strains. Electron microscopic studies reveal physical insights into the interaction and bactericidal mechanism between the prepared silver NPs and tested bacteria in question. The observed excellent antibacterial and antifungal activity of the silver NPs make them ideal for disinfection and biomedicine applications.     

Ultrafast dephasing of surface plasmon excitation in silver nanoparticles: influence of particle size,shape, and chemical surrounding

By combination of two special methods, i.e., persistent spectral hole burning and laser assisted nanoparticle preparation, the dephasing time T2 of surface plasmon excitation in silver nanoparticles was systematically investigated. A strong dependence of T2 on the plasmon energy is found which reflects the relevance of interband damping and makes necessary a precise control of the particle shape when measuring T2. The influence of the reduced dimension on the dephasing dynamics was observed as a decrease of T2 with shrinking particle size. In addition, for silver nanoparticles on quartz substrates, a considerable amount of chemical interface damping was observed.     

Hydrothermal synthesis of large maghemite nanoparticles: influence of the pH on the particle size

Maghemite nanoparticles with sizes in the range 10–110 nm and good monodispersity have been synthesized by co precipitation at room temperature from Fe²⁺ and Fe³⁺ ions by a (N(CH₃)₄OH) solution, followed by an hydrothermal treatment at 200 °C and an oxidation step with Fe(NO₃)₃. The influence of the incubation time (at 200 °C) and of the pH of the autoclaved solution on the particles size has been studied. It was found that the pH value allows to tune the size of the maghemite particles. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Effect of particle size distribution on magnetic behavior of nanoparticles with uniaxial anisotropy

The effect of particle size distribution on the field and temperature dependence of the hysteresis loop features like coercivity(H_C), remanence(M_R), and blocking temperature(T_B) is simulated for an ensemble of single domain ferromagnetic nanoparticles with uniaxial anisotropy. Our simulations are based on the two-state model for T T_B and the metropolis Monte-Carlo method for T T_B. It is found that the increase in the grain size significantly enhances H_C and T_B. The presence of interparticle exchange interaction in the system suppresses H_C but causes MRto significantly increase.Our results show that the parameters associated with the particle size distribution(D_(d,δ)) such as the mean particle size d and standard-deviation δ play key roles in the magnetic behavior of the system.     

Individual-collective crossover driven by particle size in dense assemblies of superparamagnetic nanoparticles

Prussian blue analogues (PBA) ferromagnetic nanoparticles Cs ^I _x Ni ^II [Cr ^III (CN)₆ ] _z ·3(H₂O) embedded in CTA⁺ (cetyltrimethylammonium) matrix have been investigated by magnetometry and magnetic small-angle neutron scattering (SANS). Choosing particle sizes (diameter D = 4.8 and 8.6 nm) well below the single-domain radius and comparable volume fraction of particle, we show that the expected superparamagnetic regime for weakly anisotropic isolated magnetic particles is drastically affected due to the interplay of surface/volume anisotropies and dipolar interactions. For the smallest particles (D = 4.8 nm), magnetocrystalline anisotropy is enhanced by surface spins and drives the system into a regime of ferromagnetically correlated clusters characterized by a temperature-dependent magnetic correlation length L _mag which is experimentally accessible using magnetic SANS. For D = 8.6 nm particles, a superparamagnetic regime is recovered in a wide temperature range. We propose a model of interacting single-domain particles with axial anisotropy that accounts quantitatively for the observed behaviors in both magnetic regimes.