Progress in neutron activation analysis for uranium

A new type of extractant, sym-dibenzo-16-crown-5-oxyhydroxamic acid (HL) is introduced. The extractions of UO22+, Na+, K+, Sr2+, Ba2+ and Br- were studied with HL in chloroform. The results obtained show that UO22+ can be quantitatively extracted at pH values above 5, whereas the extractions of K+, Na+, Sr2+, Ba2+ and Br- are negligible in the pH range of 2 - 7. The dependence of the distribution ratio of U(VI) on both the concentration of the HL and pH are linear, and they have the same slope of 2. This suggests that U(VI) appears to form a 1:2 complex with ligand. Uranium(VI) can be selectively separated and concentrated from interfering elements such as Na, K, Sr and Br by solvent extraction with HL under specific conditions. The recovery of uranium is nearly 100% and the radionudear purity of uranium is greater than 99.99%. Therefore, neutron activation analysis has greatly improved the sensitivity and accuracy for the detection of trace uranium from seawater.     

Development of X-ray fluorescence analysis in Russia in 1991–2010

A review attempted to examine the results of studies in X-ray fluorescence (XRF) analysis performed by Russian authors for the period from 1991 to the present time is given. This proved to be quite a challenge, since the number of articles published only on the theory and practice of XRF (excluding the development of equipment) exceeded 500. Therefore, the author had to limit himself to a more detailed presentation of only several important achievements. Further information, if necessary, can be found in the cited reviews.     

Sequential analysis of dimethyl sulfur compounds in seawater

A sequential method for the determination of dimethyl sulfur compounds, including dimethylsulfide （DMS）, dimethylsulfonio- propionate （DMSP） and dimethylsulfoxide （DMSO）, in seawater samples has been developed. Detection limit of 2.5 pmol of DMS in 25 mL sample, corresponding to 0.10 nmol/L, was achieved. Recoveries for dimethyl sulfur compounds were in the range of 68.6- 78.3%. The relative standard deviations （R.S.D.s） for DMS, DMSP and DMSO determination were 3.0, 5.4 and 7.4%, respectively.     

Nanoparticle-based pseudostationary phases in CEC: a breakthrough in protein analysis?

This review focuses on major trends in nanoparticle-based pseudostationary phase (PSP) CEC since the publication of our previous reviews within nanoparticle-based CEC [Nilsson, C., et al., Electrophoresis 2006, 27, 76-83; Nilsson, C., et al., J. Chromatogr. A 2007, 1168, 212-224.]. Special attention is given to the development toward protein analysis, which is driven by the strong emergence of protein drug development in the pharmaceutical industry. Furthermore, we discuss the development in coupling different detection techniques with nanoparticle-based PSP CEC, which were originally predicted to be particularly cumbersome. However, at present, direct UV, LIF and ESI-MS have been used without any severe complications. Different types of nanoparticles used as PSP during the period include gold nanoparticles, carbon nanostructures and lipid-based nanoparticles. New materials (for example, different types of carbon nanostructures and self assembled lipid-based nanostructures) are a strong driving force for development in separation science. Finally, future trends in nanoparticles-based CEC are envisioned.     

Advances in chromatographic analysis of ginsenosidesEI北大核心CSCD

Ginsenosides possess pharmacological activities such as anti-aging，cardiovascular protection，and improving immunity. However，the detection and analysis of ginsenosides commonly suffer from the problem of low sensitivity owing to the complex matrix and low content of ginsenosides. Chromatographic technology was often used to detect ginsenosides owing to the advantages of high accuracy，high sensitivity，good reproducibility and low sample consumption，etc. In this review，the application of chromatographic analysis technologies in ginsenosides detection was summarized. First of all，accuracy of test results for the ginsenosides can be effectively improved by using high performance liquid chromatography（HPLC）combined with various detectors. Secondly，the combination of HPLC with mass spectrometry can be utilized for qualitative and quantitative analysis of ginsenosides， as well as other fields， such as metabonomics， pharmacokinetics， intestinal microorganisms and quality control. Moreover，the application of gas chromatography in analysis of ginsenosides was reviewed. Briefly，with the continuous development of chromatographic technology，the degree of accuracy for ginsenosides detection was effectively improved，which is beneficial to realize the effective analysis of ginsenosides. © 2023, Youke Publishing Co., Ltd. All rights reserved.     

Why not using capillary electrophoresis in drug analysis?

CE and related methods are well-established techniques in the analysis of biomolecules, such as DNA and proteins. Even though CE is a rather good alternative to HPLC for the evaluation of the impurity profile and the enantiomeric purity of a drug, it is rarely applied. This might be due to the reservation of national licensing authorities and the pharmacopoeia commissions for several reasons. In this review containing some experimental data we report on several drug examples which demonstrate the superiority of CE over HPLC in special cases, i.e., in the analysis of antibiotics, amino acids and peptides, and the determination of enantiomeric purity. However, in order to make the CE techniques more suitable for pharmacopoeial purposes the general methods describing separation methods have to be complemented with the adjustment of the electrophoretic conditions being necessary to satisfy the system suitability criteria without fundamentally modifying the methods. Taken together CE should be more often applied in drug quality control.     

CellFacts II – single cell analysis in real time

CellFacts II integrates electrical flow impedance and fluorescence to determine the number, size and fluorescence characteristics of individual cells in a conductive fluid. The instrument has been optimised to detect and enumerate viable and non-viable cells in fluid samples with varied particulate content, i.e. total viable counts, with discrimination of the physiological status of the individual cells. The study shows the analysis of the physiological state of individual cells in a population, effectively in real-time, enabling the rapid determination of the effect of antimicrobial agents on these cells i.e. rapid determination and optimisation of antimicrobial agents in aqueous paint systems.     

An EPR analysis of β-dimerization in α-blocked pyrroles in oxidant conditions

Electron paramagnetic resonance (EPR) analysis of neutral and acidic solutions of 2,5-dimethyl-1-phenylpyrrol (1) and meta-, para-, and ortho-bis(2,5-dimethylpyrrol-1-yl)benzenes (4-6) in the presence of Tl(III) trifluoroacetate as oxidant reveals the poor stability of their generated monomeric radical cations which dimerize through C(β)-C(β) bond formation. EPR spectra of the monomeric radical cations 4(?+) , 5(?+) , and 6(?+) coincide with that of 1(?+) , suggesting that the unpaired electron in these charged species is confined in one of the pyrrolic rings. The very twisted angles between pyrrolic and phenyl planes due to steric hindrance in the X-ray analysis of the molecular structure of 4 confirm the absence of extended conjugation in the π-system.     

LC-MS analysis in the aquatic environment and in water treatment – a critical review

LC-MS has become an invaluable technique for trace analysis of polar compounds in aqueous samples of the environment and in water treatment. LC-MS is of particular importance due to the impetus it has provided for research into the occurrence and fate of polar contaminants, and of their even more polar transformation products. Mass spectrometric detection and identification is most widely used in combination with sample preconcentration, chromatographic separation and atmospheric pressure ionization (API). The focus of the first part of this review is directed particularly toward instruments and method development with respect to their applications for detecting emerging contaminants, microorganisms and humic substances (HS). The current status and future perspectives of 1) mass analyzers, 2) ionization techniques to interface liquid chromatography (LC) with mass spectrometry (MS), 3) methods for preconcentration and separation with respect to their application for water analysis are discussed and examples of applications are given. Quadrupole and ion trap mass analyzers with electrospray ionization (ESI) and atmospheric pressure chemical ionization (APCI) are already applied in routine analysis. Time-of-flight (TOF) mass spectrometers are of particular interest for accurate mass measurements for identification of unknowns. For non-polar compounds, different ionization approaches have been described, such as atmospheric pressure photoionization (APPI), electrochemistry with ESI, or electron capture ionization with APCI. In sample preconcentration and separation, solid phase extraction (SPE) with different non-selective sorbent materials and HPLC on reversed-phase materials (RP-HPLC) play the dominant role. In addition, various on-line and miniaturized approaches for sample extraction and sample introduction into the MS have been used. Ion chromatography (IC), size-exclusion chromatography (SEC), and capillary electrophoresis (CE) are alternative separation techniques. Furthermore, the issues of compound identification, matrix effects on quantitation, development of mass spectral libraries and the topic of connecting analysis and toxicity bioassays are addressed.     

Enantioselective CE–MS analysis of ketamine metabolites in urine

The chiral drug ketamine has long-lasting antidepressant effects with a fast onset and is also suitable to treat patients with therapy-resistant depression. The metabolite hydroxynorketamine (HNK) plays an important role in the antidepressant mechanism of action. Hydroxylation at the cyclohexanone ring occurs at positions 4, 5, and 6 and produces a total of 12 stereoisomers. Among those, the four 6HNK stereoisomers have the strongest antidepressant effects. Capillary electrophoresis with highly sulfated γ-cyclodextrin (CD) as a chiral selector in combination with mass spectrometry (MS) was used to develop a method for the enantioselective analysis of HNK stereoisomers with a special focus on the 6HNK stereoisomers. The partial filling approach was applied in order to avoid contamination of the MS with the chiral selector. Concentration of the chiral selector and the length of the separation zone were optimized. With 5% highly sulfated γ-CD in 20 mM ammonium formate with 10% formic acid and a 75% filling the four 6HNK stereoisomers could be separated with a resolution between 0.79 and 3.17. The method was applied to analyze fractionated equine urine collected after a ketamine infusion and to screen the fractions as well as unfractionated urine for the parent drug ketamine and other metabolites, including norketamine and dehydronorketamine.     

Boron in coral skeletons determined by prompt γ-ray analysis

A systematic and non-destructive technique is proposed for the determination of boron in coral samples by neutron-induced prompt γ-ray analysis (PGA) using a thermal neutron guide beam of the JRR-3M reactor. About 50–150 mg samples in sealed FEP film were irradiated and measured for 5000 s in the PGA system at a neutron flux of 2.4 × 10⁷ n cm⁻² s⁻¹. In order to determine B content in coral skeletons, the Doppler-broadened γ-ray peak of 478 keV (¹⁰B) was used together with the correction of interference from the Na-peak of 472 keV. The analytical precision was ~3% for the JCp-1 coral standard. The data (n = 56) obtained by the present method showed a range of B content from 40.7 to 76.9 ppm which is similar to reported values. Boron in corals showed the highest levels in Rukan-sho (Okinawa) with an average B content of 62.5 ppm, whereas corals collected from Mizugama (Okinawa), Cebu (the Philippines) and Khang Khao (Thailand) exhibited B contents of 56.5, 53.0 and 45.7 ppm, respectively. The uptake of boron by living corals may be influenced by seawater pH related to higher seawater B(OH)₄⁻. In this paper we discuss factors controlling the B levels in corals.     

How can structural similarity analysis help in category formation?

Chemical category is a regulatory concept facilitating filling safety data gaps. Practically, all chemical management programs like the OECD HPV Program, EU REACH, or the Canadian DSL Categorization are planning to use or are already using categorization approaches to reduce resources including animal testing. The aim of the study was to discuss the feasibility to apply computational structural similarity methods to augment formation of a category. The article discusses also how this understanding can be translated into computer readable format, an ultimate need for practical, broad scope applications. We conclude that for the skin sensitization endpoint, used as a working example, mechanistic understanding expressed as chemical reactivity can be exploited by computational structural similarity methods to augment category formation process. We propose a novel method, atom environments ranking (AER), to assess similarity to a reference training set representing a common mechanism of action, as a potential method for grouping chemicals into reactivity domains.     

LC-MS analysis in the aquatic environment and in water treatment technology – a critical review

Environmental contaminants of recent concern are pharmaceuticals, estrogens and other endocrine disrupting chemicals (EDC) such as degradation products of surfactants, algal and cyanobacterial toxins, disinfection by-products (DBPs) and metalloids. In addition, pesticides (especially their transformation products), microorganisms, and humic substances (HS), in their function as vehicles for contaminants and as precursors for by-products in water treatment, traditionally play an important role. The present status of the application of LC-MS techniques for these water constituents are discussed and examples of application are given. Solid-phase extraction with various non-selective materials in combination with liquid chromatography (LC) on reversed-phase columns have been the most widely used methods for sample preconcentration and separation for different compound classes like pesticides, pharmaceuticals or estrogens. Electrospray ionization (ESI) and atmospheric pressure ionization (APCI) are the most frequently used ionization techniques for polar and ionic compounds, as well as for less polar non-ionic ones. The facilities of LC-MS have been successfully demonstrated for different compound classes. Polar compounds from pharmaceuticals used as betablockers, iodinated X-ray contrast media, or estrogens have been determined without derivatization down to ultratrace concentrations. LC-MS can be viewed as a prerequisite for the determination of algal and cyanobacterial toxins and the homologues and oligomers of alkylphenol ethoxylates and their metabolites. Tandem mass spectrometric techniques and the use of diagnostic ions reveal their usefulness for compound-class specific screening and unknown identification, and are also valid for the analysis of pesticides and especially for their transformation products. Structural information has been gained by the application of LC-MS methods to organometallic species. New insights into the structural variety of humic substances have been made possible by FT-ICR-MS due to its ultrahigh mass resolution. Finally, exciting possibilities for rapid detection and identification of microorganisms have been made possible by MALDI and LC-MS methods.     

Space charge analysis in polyimide (kapton–H) samples

The space charge trapping/detrapping in thermally charged polyimide (PI) samples have been studied by means of “Final Thermally Stimulated Discharge Current” (FTSDC). We investigate the effects associated with space charge behavior in PI near glass transition region. The FTSDC spectra consist of space charge peak attributed trapping of charges at different trapping levels. The peak positions are found to be very sensitive with poling time, discharging time, and heating rate. The apparent activation energy distributed in the range from 0.51 to 1.12 eV, and the charge released has been found to be varying with poling temperature (T _p) and poling time (t _c)/discharging time (t _d). The decay of space charge (Q) resembled an agreement with interfacial polarization.     

Review of thin-layer chromatography in pesticide analysis: 2014–2016

ABSTRACT

Publications reporting techniques and applications of thin-layer chromatography (planar chromatography) for the separation, detection, qualitative and quantitative determination, and preparative isolation of pesticides and their metabolites are reviewed for the period from November 1, 2014 to November 1, 2016. Analyses are described for a variety of sample types and pesticide classes. In addition to references on residue analysis, studies such as pesticide chromatographic retention, identification and characterization of natural pesticides, metabolism, bioactivity, degradation, soil mobility, and lipophilicity are covered. The unique advantages of thin-layer chromatography in presenting results as a stored image on an open stationary phase are addressed.     

Sensitive analysis of amino acids in injection liquor by reversed-phase HPLC

A convenient derivatization method of amino acids with l-fluoro-2,4-dimtrobenzene as reaction reagent and a separation system were described. The derivative amino acids were separated on a specific chemically bonded phase column with a simple linear gradient elution consisting of aqueous buffer and methanol. The eluate was detected by common ultraviolet absorption detector at 360 nm. The detection limits of amino acids were as low as 10 picomole. This method has been successfully applied to assay amino acid injection liquor used in hospital. It has good repro-ducibility and precision. The procedures avoid the requirements of particular derivative equipment and analyzer employed in conventional amino acid analysis.     

Direct analysis in real time—a critical review on DART-MS

Direct analysis in real time mass spectrometry (DART-MS) has become an established technique for rapid mass spectral analysis of a large variety of samples. DART-MS is capable of analyzing the sample at atmospheric pressure, essentially in the open laboratory environment. DART-MS can be applied to compounds that have been deposited or adsorbed on to surfaces or that are being desorbed therefrom into the atmosphere. This makes DART-MS suitable and well-known for analysis of ingredients of plant materials, pesticide monitoring on vegetables, forensic and safety applications such as screening for traces of explosives, warfare agents, or illicit drugs on luggage, clothes, or bank notes, etc. DART can also be used for analysis of either solid or liquid bulk materials, as may be required in quality control, or to quickly investigate the identity of a compound from chemical synthesis. Even living organisms can be subjected to DART-MS. Driven by different needs in analytical practice, the combination of the DART ionization source and interface can be configured in multiple geometries and with various accessories to adapt the setup as required. Analysis by DART-MS relies on some sort of gas-phase ionization mechanism. In DART, initial generation of the ionizing species is by use of a corona discharge in a pure helium atmosphere which delivers excited helium atoms that, upon their release into the atmosphere, will initiate a cascade of gas-phase reactions. In the end, this results in reagent ions created from atmospheric water or (solvent) vapor in the vicinity of the surface subject to analysis where they effect a chemical ionization process. DART ionization processes may generate positive or negative ions, predominantly even-electron species, but odd-electron species do also occur. The prevailing process of analyte ion formation from a given sample is highly dependent on analyte properties.     

Light element analysis in steel by high–energy heavy–ion time of flight elastic recoil detection analysis

Time of flight elastic recoil detection analysis (TOF–ERDA) using high–energy heavy ions has been applied to determining the composition of light elements in stainless–steel (SUS304) samples before and after welding in order to monitor the variation in the composition of light elements in sample surfaces during a welding process. An argon–welding method using a welding rod (SUS304) and an arc–welding method using a welding rod were used to prepare samples. Four samples, welded and non–welded using two welding methods, were measured. ⁴⁰Ar ions accelerated to 40.3 MeV were used as a probe. Carbon, oxygen and sodium were measured. It was found that the oxygen distributions near to the surfaces of the welded samples increased compared with those of the non–welded samples. However, variations in the carbon distributions were relatively smaller than that of oxygen distributions.