聚硫堇半导体性质的电化学证据

聚硫堇的电导率为9.6×10－6 S•cm－1,属有机半导体.在10 ℃至60 ℃温度范围内,测定了聚硫堇的循环伏安图、恒电位下的放电曲线和交流阻抗图,并测定了电解质溶液的电导率随温度的变化.在聚硫堇的循环伏安图上有一阳极峰和一阴极峰,它们的峰电流均随温度的升高而增加;恒电位下的放电电流也随温度升高而增加;而交流阻抗的结果表明,聚硫堇的电荷传递电阻Rct随温度升高而下降,即它的交换电流i0随温度升高而增加;而溶液电阻和膜电阻也随温度的升高而下降,这同样会引起电流随温度升高而增加.所以温度对固体半导体聚硫堇的电极反应速率的影响包含了电极反应的本身和电极的电导率等因素的影响.聚硫堇的扫描电镜图证实了它的表面是一种纤维状结构.     

Effect of head group size, temperature and counterion specificity on cationic micelles

The critical micelle concentration (cmc) and ionisation degree (α), of micelles of cetyltrimethylammonium bromide (CTABr), cetyltrimethylammonium chloride (CTACl), cetyltripropylammonium bromide (CTPABr) and cetyltripropylammonium chloride (CTPACl) have been measured over a narrow temperature range at 2 degree intervals using electrical conductivity. CTPACl and CTPABr are very soluble in water and were measured in the temperature range 275.15-323.15K. The Krafft temperatures for CTABr and for CTACl are 293.15K and 284.15K, respectively and established a lower temperature limit for our studies on these two surfactants. The cmc vs temperature curves have a smooth minimum near room temperature and α linearly increases with temperature. The changes of cmc and α with temperature are smaller than those associated with the modification of head group size or counterion nature. Using these results, basic thermodynamic quantities associated with the phenomena of micellization have been evaluated. Thermodynamic properties of the surfactant solutions were discussed in terms of temperature dependence of the free energy, enthalpy and entropy of micellization. A close similarity between the effects of change in temperature on protein folding and micellization process appears from the data.     

不同灰化温度下生物质混煤灰的烧结特性研究

选取晋城无烟煤和麦秆作为研究对象,利用压差法烧结温度测定装置测量不同灰化温度下煤和麦秆混合灰的烧结温度,再利用SEM-EDS以及XRD对灰样进行烧结特性分析。结果表明,不论灰化温度高低,随着麦秆的添加,煤和麦秆混合灰的烧结温度都呈现降低趋势,其降低幅度略有差别。灰化温度较低时,煤和麦秆混合灰的烧结温度低于灰化温度较高情况下混合灰的烧结温度。SEM-EDS分析表明,低温灰化得到的样品中出现较多不规则的纤维结构;较高温度下获得的灰样中出现较多致密的球状颗粒,这表明矿物质发生熔融形成球状颗粒。XRD分析表明,低温灰化烧结后的煤和麦秆混合灰样中因含有较多的含钾等碱金属系助融矿物质,导致混合灰样的烧结温度降低。然而,像钙长石等含钙矿物质本身具有较高的熔点,因此,在1 100℃时混合灰样具有较高的烧结温度。     

In Situ Investigations of Mechanochemical One‐Pot Syntheses

We present an in situ triple coupling of synchrotron X‐ray diffraction with Raman spectroscopy, and thermography to study milling reactions in real time. This combination of methods allows a correlation of the structural evolution with temperature information. The temperature information is crucial for understanding both the thermodynamics and reaction kinetics. The reaction mechanisms of three prototypical mechanochemical syntheses, a cocrystal formation, a C?C bond formation (Knoevenagel condensation), and the formation of a manganese‐phosphonate, were elucidated. Trends in the temperature development during milling are identified. The heat of reaction and latent heat of crystallization of the product contribute to the overall temperature increase. A decrease in temperature occurs via release of, for example, water as a by‐product. Solid and liquid intermediates are detected. The influence of the mechanical impact could be separated from temperature effects caused by the reaction.     

A simple electro-optic technique for studying the electroclinic effect in the smectic A* phase

The critical behaviour of the electroclinic response in the chiral smectic A* phase in the vicinity of the second-order smectic A* to smectic C* phase-transition temperature has been investigated using a new electro-optic technique. The temperature variation of the electroclinic coefficient, the relaxation frequency and the coefficient of the quartic term in the tilt angle in the Landau free energy expansion have been studied. The electroclinic coefficient diverges with decreasing temperature as the smectic A* to smectic C* phase-transition temperature is approached with a critical exponent, as predicted in the mean field Landau theory. The measured quartic coefficient varies strongly with temperature, contrary to the usual assumptions of the mean field Landau theory.     

注射成型聚碳酸酯厚度截面的残余应力分析

通过光弹法定量测量了注射成型聚碳酸酯(PC)试样在厚度截面上的残余应力,并结合模具温度的变化与不对称分布,对厚度截面上的残余应力分布进行了详细的研究.结果表明,在厚度截面上,试样边缘分布较高的流动残余应力,芯部分布较高的热残余应力,两区域界面处为流动应力与热应力相互耦合而形成的低应力过渡区;模具温度低于120?C时,PC的残余应力随模具温度的变化并不明显;模具温度高于120?C时,PC的残余应力随模具温度的升高显著降低;不对称模具温度会导致在低模温侧高热残余应力区分布宽,在高模温侧高热残余应力区分布窄.此外,试样的翘曲随模具温度的升高而逐渐增加,不对称模具温度会导致较大的翘曲.     

Transport properties of thermally responsive anion exchange membranes containing N‐isopropylacrylamide in electrodialysis

Anion exchange membranes containing N‐isopropylacrylamide as a component were prepared, and their electrochemical properties were examined. The membranes were crosslinked with ethylene glycol dimethacrylate and contained weakly basic or strongly basic anion exchange groups. The dependence of electrochemical properties of the membranes (electrical resistance, transport number of anions, water content, and reduced osmotic flux) on temperature was completely different from those of the anion exchange membrane without N‐isopropylacrylamide. For example, the reduced osmotic flux decreased with increasing temperature until 40°C, and the transport number of chloride ions increased with increasing temperature from 25.0°C, although those of the conventional membrane monotonously increased or decreased. The transport numbers of various anions relative to chloride ions in electrodialysis were evaluated at a different temperature. Although the transport numbers between anions did not change appreciably in the conventional membrane with temperature, those of the anion exchange membranes with N‐isopropylacrylamide changed with a temperature dependent on the hydration degree of anions: permeation of less‐hydrated anions such as nitrate and bromide ions compared with chloride ions increased with increasing temperature, and that of strongly hydrated anions such as sulfate and fluoride ions decreased with increasing temperature. This is based on the increase or decrease in uptake of the anions in the membrane with the change in temperature because hydrophilicity of the membranes changes with temperature due to the apparent aggregation of isopropyl groups in the membranes. And the change in electrochemical properties and transport numbers of various anions relative to chloride ions with temperature was completely reversible with increasing or decreasing temperature. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 793–804, 1999     

Comportement viscosimètrique du PMMA dans le dimethylformamide en fonction de la température

We have studied the viscometric behaviour of PMMA in DMF as a function of temperature for four fractions of polymer. The results show a variation of viscosity with temperature according to the equation of Guzman and Andrade and according to the predictions from Moore's treatment. DMF behaves as a good solvent for PMMA, its quality improving with temperature. The unperturbed dimensions of the polymer increase slightly with temperature without any important conformational effect.     

Modelling the thermal behaviour of the low-thermal mass liquid chromatography system

We report upon the experimental investigation of the heat transfer in low thermal mass LC (LTMLC) systems, used under temperature gradient conditions. The influence of the temperature ramp, the capillary dimensions, the material selection and the chromatographic conditions on the radial temperature gradients formed when applying a temperature ramp were investigated by a numerical model and verified with experimental temperature measurements. It was found that the radial temperature gradients scale linearly with the heating rate, quadratically with the radius of the capillary and inversely to the thermal diffusivity. Because of the thermal radial gradients in the liquid zone inside the capillary lead to radial viscosity and velocity gradients, they form an additional source of dispersion for the solutes. For a temperature ramp of 1 K/s and a strong temperature dependence of the retention of small molecules, the model predicts that narrow-bore columns (i.d. 2.1 mm) can be used. For a temperature ramp of 10 K/s, the maximal inner diameter is of the order of 1 mm before a substantial increase in dispersion occurs.     

Use of maximum temperature for correction of alanine dosimetry in electron beams

Alanine dosimetry is well characterized for irradiation temperature response. In use, alanine absorbed dose response is corrected for the irradiation temperature. The temperature used to correct alanine dosimetry absorbed dose response in electron beams has historically been the mean temperature occurring during irradiation (Sharpe and Miller, 2009). At lower absorbed doses, the change in temperature is relatively low; thus the absorbed dose response correction due to temperature is small. However, industrial electron beam processing often requires higher absorbed dose measurements where the change in temperature can be very large and the corresponding dose response correction for alanine becomes significant. This paper compares the impact of the temperature correction based on the use of a mean irradiation temperature (Sharpe and Miller, 2009) versus the use of a maximum irradiation temperature on the absorbed dose measurement. The results of this comparison indicate that the use of a mean temperature correction for higher absorbed doses measured with temperature corrected alanine dosimetry introduces a bias in the absorbed dose estimate.     

Bioconversion of cellulose into ethanol by nonisothermal simultaneous saccharification and fermentation

The kinetic characteristics of cellulase and beta-glucosidase during hydrolysis were determined. The kinetic parameters were found to reproduce experimental data satisfactorily and could be used in a simultaneous saccharification and fermentation (SSF) system by coupling with a fermentation model. The effects of temperature on yeast growth and ethanol production were investigated in batch cultures. In the range of 35-45 degrees C, using a mathematical model and a computer simulation package, the kinetic parameters at each temperature were estimated. The appropriate forms of the model equation for the SSF considering the effects of temperature were developed, and the temperature profile for maximizing the ethanol production was also obtained. Briefly, the optimum temperature profile began at a low temperature of 35 degrees C, which allows the propagation of cells. Up to 10 h, the operating temperature increased rapidly to 39 degrees C, and then decreased slowly to 36 degrees C. In this nonisothermal SSF system with the above temperature profile, a maximum ethanol production of 14.87 g/L was obtained.     

Thin-layer chromatography with high-boiling mobile phase. part 2: Effect of temperature on retention characteristics in TLC with high-boiling mobile phases

A study has been undertaken on the effect of temperature on retention characteristics in thin-layer chromatography (TLC) with low-volatility mobile phases (MP). It is shown that temperature variations in TLC in melts bring about variations in both the relative retention values and, in some cases, in the order of migration of the chromatographic zones across the layer. The variation in the capacity factor k' with temperature agrees well with Martin's equation. To explain the temperature dependence of R_f one must, in general, take into account the variations with temperature in both the partition coefficient and the phase ratio. To describe the variation in R_f with temperature in TLC with low-volatile MP one can use an approximate equation in which In R_f is a linear function of 1/T. The experiments indicate that temperature is a major factor in TLC in melts.     

Molecular Origin for the Thermal Stability of Rice Amylopectin 1

Abstract

The non-Newtonian behavior and dynamic viscoelasticity of Takanari and Reimei amylopectin solutions were measured with a rheogoniometer. The Takanari and Reimei amylopectin showed plastic behavior at a concentration above 2.0% at 25 °C. The viscosity of Takanari amylopectin decreased a little with increasing temperature at 2.0%. However, a little increase in the viscosity was observed with increasing temperature from 0 to 15 °C, then it stayed at a constant value with further increase in the temperature up to 80 °C at a concentration above 4.0%. An increase in the viscosity was also observed in Reimei amylopectin solution at various concentrations. The dynamic viscoelasticity of Takanari amylopectin increased with increasing concentration at low temperature (0 °C) and it stayed at a constant value with increasing temperature up to 80 °C. On the other hand, dynamic viscoelasticity for Reimei amylopectin showed a weak sigmoid curve. The tan δ of both amylopectins showed low values, 0.32-0.38, at low temperature range and kept constant with increasing temperature up to 80 °C. A little decrease of dynamic modulus of Takanari and Reimei amylopectin was observed upon addition of urea (4.0 M). The dynamic modulus of Takanari and Reimei amylopectin solution decreased rapidly when the temperature reached 45 and 60 °C, which was estimated to be a transition temperature, in 0.10 N NaOH solution. The molecular origin for the thermal stability of rice amylopectin (Takanari and Reimei) was essentially attributed to intramolecular associations in aqueous solution. Possible mode of intramolecular hydrogen bonding and van der Waals forces of attraction of amylopectin molecules are proposed.

     

聚合物熔体冷却阶段结晶行为的多尺度模拟

针对结晶型聚合物熔体冷却过程的结晶行为,建立了偶合宏观温度场与微观结晶形态的多尺度模型.该模型揭示了宏观温度的变化会引起晶核数、晶体生长速率的改变,从而影响微观结晶形态;而微观结晶释放的潜热也将导致宏观温度的改变.为了求解上述多尺度模型,提出了有限体积/像素法偶合的多尺度算法,即在粗网格上采用有限体积法对宏观温度场进行求解,而在细网格上采用像素法对微观结晶形态进行模拟.基于多尺度模型及多尺度算法,文中对二维聚合物熔体模壁等速降温的冷却问题进行了研究,考察了温度、相对结晶度的变化及结晶形态的演化,并比较了不同冷却速率、初始温度对温度、相对结晶度及结晶形态的影响.数值结果表明,冷却速率是影响结晶行为的关键.高冷却速率下,温度平台出现较早,持续较短;结晶过程对应的温度范围较广;且平均晶体直径较小.而初始温度只影响温度平台及结晶行为出现的早晚,与其持续时间几乎无关。     

Measurement of the axial and radial temperature profiles of a chromatographic column. Influence of thermal insulation on column efficiency

The temperatures of the metal wall along a chromatographic column (longitudinal temperature gradients) and of the liquid phase across the outlet section of the column (radial temperature gradients) were measured at different flow rates with the same chromatographic column (250 mm x 4.6 mm). The column was packed with 5 microm C18-bonded silica particles. The measurements were carried out with surface and immersion thermocouples (all junction Type T, +/-0.1 K) that measure the local temperature. The column was either left in a still-air bath (ambient temperature, T(ext) = 295-296 K) or insulated in a packing foam to avoid air convection around its surface. The temperature profiles were measured at several values of the inlet pressure (approximately = 100, 200, 300 and 350 bar) and with two mobile phases, pure methanol and a 2.5:97.5 (v/v, %) methanol:water solution. The experimental results show that the longitudinal temperature gradients never exceeded 8 K for a pressure drop of 350 bars. In the presence of the insulating foam, the longitudinal temperature gradients become quasi-linear and the column temperature increases by +1 and +3 K with a water-rich (heat conductivity approximately = 0.6 W/m/K) and pure methanol (heat conductivity approximately = 0.2 W/m/K), respectively. The radial temperature gradients are maximum with methanol (+1.5 K at 290 bar inlet pressure) and minimum with water (+0.8 K at 290 bar), as predicted by the solution of the heat transfer balance in a chromatographic column. The profile remains parabolic all along the column. Combining the results of these measurements (determination of the boundary conditions on the wall, at column inlet and at column outlet) with calculations using a realistic model of heat dispersion in a porous medium, the temperature inside the column could be assessed for any radial and axial position.     

Evaluation of the thermal effect on separation selectivity in anion-exchange processes using superheated water ion-exchange chromatography

The thermal effect on retention and separation selectivity of inorganic anions and aromatic sulfonate ions in anion-exchange chromatography is studied on a quaternized styrene-divinylbenzene copolymer anion-exchange column in the temperature range of 40-120 °C using superheated water chromatography. The selectivity coefficient for a pair of identically charged anions approaches unity as temperature increases provided the ions have the same effective size, such that the retention of an analyte ion decreases with an increase in temperature when the analyte ion has stronger affinity for the ion-exchanger than that of the eluent counterion, whereas it increases when it has weaker affinity. The change in anion-exchange selectivity with temperature observed with superheated water chromatography has been discussed on the basis of the effect of temperature on hydration of the ions. At elevated temperatures, especially in superheated water, the electrostatic interaction or association of the ions with the fixed ion in the resin phase becomes a predominant factor resulting in a different separation selectivity from that obtained at ambient temperature.     

还原温度与时间对铁基催化剂浆态床F-T合成性能的影响

在浆态床反应器中考察了未还原催化剂以及在240℃和270℃的还原温度下还原时间对Fe/Cu/K/SiO2催化剂F-T合成反应性能的影响,采用Mssbauer谱研究了还原和反应后催化剂的物相组成。结果表明,在240℃延长还原时间或将还原温度升高到270℃均有利于催化剂的还原,270℃还原的催化剂的活性和稳定性明显高于未还原和240℃还原的催化剂,催化剂的运行稳定性与催化剂在反应过程中的流失量有密切关系。催化剂高温还原时烃产物分布倾向于生成低碳数的烃类,在相同的还原温度下,烃产物选择性随还原时间的延长向轻组分方向偏移。     

Temperature dependence of microhardness in the 70/30 polyvinylidene fluoride-trifluorethylene copolymer: New structural aspects of the curie transition

A combined X-ray diffraction and microhardness investigation of the 70/30 polyvinylidene fluoride-trifluorethylene copolymer was carried out as a function of temperature. The changes in microhardness are interpreted in terms of variations in lattice spacing of the ferro- and paraelectric phases, crystallinity and long period. The changes of microhardness with temperature show four distinct temperature regions. In addition to a low temperature range, in which microhardness decreases exponentially with temperature, the ferroparaelectric Curie transition involves a faster hardness decrease. At higher temperature, the sudden microhardness rise is ascribed primarily to an increase of crystal thickness within the remnant paraelectric phase. Near the melting point, the fusion of thinner crystals leads to a range in which microhardness decreases exponentially again.     

Influence of temperature on mass transfer in an incomplete trapping single hollow fibre supported liquid membrane extraction of triazole fungicides

The influence of temperature in a single hollow fibre supported liquid membrane extraction of triazole fungicides with a stagnant acceptor phase was investigated. The mass transfer parameters such as diffusion coefficient, flux and apparent viscosity were determined at temperature ranging from 278 K to 313 K. Increase in temperature led to an increase in diffusion coefficient and flux. The apparent viscosity also decreased with an increase in temperature. The degree of trapping in the acceptor phase influenced the mass transfer at higher temperature. At lower temperature, the transport of analytes from the donor solution through the donor-membrane interface and through the membrane mainly affected the transport of triazole fungicides. The effect of temperature in a single hollow fibre SLM extraction technique is therefore more pronounced where transport is donor controlled and/or membrane controlled. The partition coefficient of analytes from the acceptor solution to the membrane, K_A was found to be much higher than that of from the donor solution to the membrane K_D, thus least trapped triazole fungicides preferred to remain in the membrane even with an increased extraction temperature.     

利用Py-GC/MS研究温度和时间对生物质热解的影响

以稻壳为原料,采用Py-GC/MS装置对其在不同热解条件下进行快速热解,并对热解气进行在线检测分析,考察了热解温度和时间对生物质热解性质的影响.结果表明,低于450 ℃,随着温度的升高,生物质热解产物种类及其产率均增加,但低温条件下产物种类较少,有利于产物的分离提纯;高于450 ℃,生物质热解产物种类基本稳定,仅在产率上有所变化,当550 ℃时,收率最大.随着热解温度的升高,其对应的最佳热解时间缩短,且生物质低温热解时间延长时热解比高温解热时间缩短时热解更充分.