Capillary electrophoretic determination of inorganic anions in the drainage and surface water samples.

Capillary electrophoresis was used for separation and quantitation of several inorganic anions in the drainage and surface water samples from the region with extensive use of fertilisers. Baseline separation of 13 small anions including nitrite and nitrate up to the concentrations of 100 mg/l was achieved in less than 5 min. The electrolyte consisted of 3 mM K2CrO4, 30 microM cetyltrimethylammonium bromide and 3 mM boric acid at pH 8. The method yielded precisions of 1.8-7.2% (RSD, n = 10) and detection limits from 4 micrograms/l (Cl-) up to 500 micrograms/l (citrate). The results of the CE method were compared to ion chromatography using water-acetonitrile (86:14) at pH 8.6 adjusted with NaOH as the mobile phase and consistent results were obtained.     

Capillary electrophoretic analysis of inorganic anions in atmospheric hailstone samples

Micellar electrokinetic capillary chromatography (MEKC) coupled with sample stacking and polarity switching was investigated for the determination of Viagra (sildenafil citrate, SC) and its metabolite (UK-103,320, UK) in human serum in the concentration range of clinical interest. Human serum samples spiked with SC and UK were eluted with methanol from a C18 cartridge, the extract was evaporated and regenerated in a solution that contained 1 mM phosphate buffer (pH 12.3) and 20% methanol. The MEKC separation was performed using an injection time of 275 s, a polarity switching time of 93 s, a phosphate buffer, (pH 12.3, 15 mM) containing 25 mM sodium dodecyl sulfate as separation electrolyte and a fused-silica capillary. The analysis takes about 6 min and gives satisfactory inter-day precision with respect to migration times and linear responses over the 80-900 ng/ml concentration range investigated for SC and UK. Intra-day RSDs (n=4 graphs) for the slopes of the calibration graphs were 4.86% for SC and 3.50% for UK. Inter-day RSDs for the slopes were 4.37% for SC and 5.39% for UK. Detection limits (S/N=3) were about 17 ng/ml for both compounds in human serum. A 1-ml volume of blood serum was necessary to do this determination.     

Capillary electrophoresis for short-chain organic acids and inorganic anions in different samples

This review article is a comprehensive survey of capillary electrophoresis methods developed for the measurement of short-chain organic acids and inorganic anions in a wide variety of matrices, such as food and beverages, environmental, industry, and other applications, as well as clinical applications in body fluids such as urine, plasma or cerebrospinal fluid. Details of sample pretreatment and of electrophoretic conditions have been collected in tables, arranged by the type of matrix. Strategies employed for method development for the analysis of these compounds by capillary electrophoresis in real samples are discussed.     

Capillary electrophoretic determination of inorganic selenium species

The performance of pyromellitic electrolyte for capillary zone electrophoresis of inorganic selenium species in the presence of selected common anions with indirect UV detection was investigated. The separation was achieved with pyromellitic electrolyte at pH 8.8 and hexamethonium hydroxide as the electroosmotic flow modifier. Obtained detection limits of 0.17 microg ml(-1) for Se(VI) and 0.29 microg ml(-1) for Se(IV) were improved by a factor of 5-7 in comparison with chromate electrolyte, which has been mainly employed for selenium analysis. Good resolution for nitrate-Se(VI) peaks were obtained.     

Capillary electrophoretic separation of inorganic and organic arsenic compounds

Capillary zone electrophoresis was used to separate arsenite, arsenate, dimethylarsinic and diphenylarsinic acid, methanearsonic acid, phenyl- and p-aminophenyl arsonic acid, phenylarsineoxide and phenarsazinic acid. Anionic and uncharged species were separated in a fused silica capillary with on-column UV detection at 200 nm. A 15 mM phosphate solution adjusted to pH 6.5 containing 10 mM sodium dodecylsulfonate served as background electrolyte. The influence of pH and applied voltage on separation efficiency, as well as the feasibility of identification of arsenic compounds in spiked urine, were investigated. Received: 18 March 1998 / Revised: 25 May 1998 / Accepted: 30 May 1998     

Capillary electrophoretic separation of inorganic and organic arsenic compounds

Capillary zone electrophoresis was used to separate arsenite, arsenate, dimethylarsinic and diphenylarsinic acid, methanearsonic acid, phenyl- and p-aminophenyl arsonic acid, phenylarsineoxide and phenarsazinic acid. Anionic and uncharged species were separated in a fused silica capillary with on-column UV detection at 200 nm. A 15 mM phosphate solution adjusted to pH 6.5 containing 10 mM sodium dodecylsulfonate served as background electrolyte. The influence of pH and applied voltage on separation efficiency, as well as the feasibility of identification of arsenic compounds in spiked urine, were investigated. Received: 18 March 1998 / Revised: 25 May 1998 / Accepted: 30 May 1998     

Capillary zone electrophoresis for the determination of light-absorbing anions in environmental samples.

A rapid and simple method for separation and determination of inorganic anions by capillary zone electrophoresis was described. The detection was carried out directly with a diode array detector. The experimental conditions, such as concentration of carrier electrolyte, capillary length, voltage, and temperature were optimized. In order to improve selectivity, different organic modifiers were also investigated. The baseline separation of 10 light-absorbing anions was accomplished within 3.5 min with a background electrolyte consisting of 50 mM sodium tetraborate containing 5% MeOH. Linear plots were obtained in the concentration range of 0.1-10 microg/ml. With sample stacking injection, the quantitation limits of the anions were found to be in the range of 0.02-0.1 microg/ml. The proposed method was successfully applied to the determination of inorganic anions in environmental samples and in effluents of a power plant.     

Capillary electrophoresis method for analysis of inorganic and organic anions related to habitability and the search for life

In situ missions of exploration require analytical methods that are capable of detecting a wide range of molecular targets in complex matrices without a priori assumptions of sample composition. Furthermore, these methods should minimize the number of reagents needed and any sample preparation steps. We have developed a method for the detection of metabolically relevant inorganic and organic anions that is suitable for implementation on in situ spaceflight missions. Using 55 mM acetic acid, 50 mM triethylamine, and 5% glycerol, more than 21 relevant anions are separated in less than 20 min. The method is robust to sample ionic strength, tolerating high concentrations of background salts (up to 900 mM NaCl and 300 mM MgSO₄). This is an important feature for future missions to ocean worlds. The method was validated using a culture of Escherichia coli and with high salinity natural samples collected from Mono Lake, California.     

毛细管电泳定量检测环境水样中无机阴离子

详细讨论了胶束浓度、间接吸收背景物质的浓度及有机添加剂组成等对部分卤素及其含氧酸根的毛细管电泳分离影响;在优化的条件下,3.5min内高效、快速地完成了Cl-、Br-、ClO3-、BrO3-四种无机阴离子的分离分析,分离的理论塔板数在1.6×106～2.8×105/m之间,检出限在11.2～23.3mg/L之间,迁移时间的相对标准偏差小于1%,峰面积的相对标准偏差在5.2%～2.2%之间;并将方法用于环境水样的分析。     

Capillary electrophoretic determination of carboxyhemoglobin concentrations in postmortem blood samples

The use of capillary electrophoresis (CE) as an alternative to existing methods of quantitation of carbon monoxide (CO) in hemoglobin from postmortem blood samples is presented. The isolation of heme (the portion of the hemoglobin molecule in which CO binding takes place) from hemoglobin is described. Reduced (containing no gas molecules) heme and CO-heme isolated from hemoglobin standards were successfully separated using CE. Heme and CO-heme were also isolated from blood samples of accident victims and analyzed using CE. A quantifiable difference in the CO-heme signals from blood samples containing fatal and nonfatal levels of CO was observed.     

Capillary electrophoretic determination of inorganic ions in a prenatal vitamin formulation

Methods for the quantitative analysis of three cations (calcium, iron and zinc), and the qualitative analysis of several anionic species (chloride, sulfate, nitrate, citrate, fumerate, phosphate, carbonate and acetate) from a prenatal vitamin formulation by two different capillary ion electrophoresis methods are reported. The cation method was evaluated for detection and quantitation limits, precision, accuracy and linearity. For standard solutions, detection limits into the ng/ml range, and reproducibility that averaged less than 1% for migration time and 2% for area response were generated. Calibration plots exhibited linearity in excess of three orders of magnitude. In addition, excellent agreement between capillary ion electrophoresis and flame photometry quantitative results for the cation analyses were obtained.     

Capillary zone electrophoretic studies of ion association between inorganic anions and tetraalkylammonium ions in aqueous-dioxane media

Ion association between inorganic anions and symmetrical tetraalkylammonium ions, R4N+ (R = Me, Et, Pr, n-Bu, n-Am, and 2-methyl butyl {isoamyl = iAm}) was investigated using ordinary silica capillary by capillary zone electrophoresis. An improved version of the Williams-Vigh method was used for the first time to measure the mobilities of the inorganic anions. Plots of log Kass against log dielectric constant in various media, revealed a smaller change in Kass compared to dielectric constant. These plots suggest that the Bjerrum's equation is inadequate in accounting for the associations of ions in a CZE setup.     

Capillary electrophoresis method for the analysis of inorganic anions, organic acids, amino acids, nucleotides, carbohydrates and other anionic compounds.

A previously developed capillary zone electrophoresis (CZE) method with indirect UV detection for the simultaneous determination of inorganic and organic anions, amino acids and carbohydrates using 20 mM 2,6-pyridinedicarboxylic acid (PDC) as the background electrolyte was extended to allow determination of 206 anions including those above--mentioned and physiological amino acids, nucleotides, aromatic acids, haloacetic acids, alcohols, phosphorylated saccharides, oxyhalides, metal oxoacids, metal-ethylenediaminetetraacetic acid (EDTA) complexes, forensic anions, Good's buffers and herbicides. Every compound could be analyzed and their electrophoretic mobility determined simply by selecting detection wavelength. This method is simple and universal for anion analysis, and could be readily applied to the simultaneous determination of anionic compounds. In this work, it was used to identify and quantify important anions in sea urchin and sake.     

Capillary ion electrophoresis, an environmental method for the determination of anions in water

Capillary ion electrophoresis has recently been introduced as a new separations technique for the analysis of of inorganic anions. Among its many attributes are rapid, highly efficient separations with different selectives (compared to ion chromatography), simplicity, and economy.

This paper demonstrates the ability of capillary ion electrophoresis to analyze primary and secondary anionic contaminants as well as other ions of environmental concern in drinking water, groundwater, and wastewater. Analysis time is less than five minutes. A comparison of the data to ion chromatography shows excellent correlation.     

On-capillary sample cleanup method for the electrophoretic determination of carbohydrates in juice samples

On many occasions, sample treatment is a critical step in electrophoretic analysis. As an alternative to batch procedures, in this work, a new strategy is presented with a view to develop an on-capillary sample cleanup method. This strategy is based on the partial filling of the capillary with carboxylated single-walled carbon nanotube (c-SWNT). The nanoparticles retain interferences from the matrix allowing the determination and quantification of carbohydrates (viz glucose, maltose and fructose). The precision of the method for the analysis of real samples ranged from 5.3 to 6.4%. The proposed method was compared with a method based on a batch filtration of the juice sample through diatomaceous earth and further electrophoretic determination. This method was also validated in this work. The RSD for this other method ranged from 5.1 to 6%. The results obtained by both methods were statistically comparable demonstrating the accuracy of the proposed methods and their effectiveness. Electrophoretic separation of carbohydrates was achieved using 200 mM borate solution as a buffer at pH 9.5 and applying 15 kV. During separation, the capillary temperature was kept constant at 40 degrees C. For the on-capillary cleanup method, a solution containing 50 mg/L of c-SWNTs prepared in 300 mM borate solution at pH 9.5 was introduced for 60 s into the capillary just before sample introduction. For the electrophoretic analysis of samples cleaned in batch with diatomaceous earth, it is also recommended to introduce into the capillary, just before the sample, a 300 mM borate solution as it enhances the sensitivity and electrophoretic resolution.     

一种基于二喹啉甲酸- Cu+显色反应的毛细管电泳检测蛋白质的新方法

采用毛细管电泳法和蛋白质显色反应-二喹啉甲酸(BCA)法,结合微波辅助反应,在60 mmol/L硼酸盐缓冲液(pH 9.5)中,实现了对蛋白质的快速毛细管电泳分析检测。同时以β-环糊精为包合添加剂,实现了BCA-Cu+复合物和游离BCA的分离,从而在波长200 nm处以测定特征生成的BCA-Cu+复合物来间接检测蛋白质,其峰强度比直接检测蛋白质自身吸收的峰强度提高了2个数量级。对于转铁蛋白、蓖麻毒素,其线性范围分别为2～200 mg/L和2～100 mg/L,检出限分别为0.33和0.37 mg/L。将该方法成功地应用于第一届蓖麻毒素国际实验室间比对测试的部分样品,含量测定结果满意。     

Capillary electrophoretic determination of the protease Savinase in cultivation broth.

The highly basic washing enzyme Savinase and various analogues were analysed by micellar electrokinetic chromatography (MEKC) and electrophoresis. Broth samples were withdrawn during the cultivation of Savinase by recombinant microorganisms. Savinase peak areas obtained by MEKC-electrophoretic analysis were normalized with respect to migration time and compared with traditional enzyme activity measurements. The electropherograms indicated thermal degradation of the Savinase molecule at high field strengths. Baseline separation of Savinase and two analogues was achieved.