离子色谱柱后衍生光度法检测食品中含硫的阴离子化合物

研究了一种离子色谱柱后衍生直接光度法测定食品中含硫阴离子化合物．采用IonPacAS22A分析柱（250mm×4mm）,IonPacAG22A保护柱（50mm×4mm）,4．5mmol·L^-1碳酸钠和0．8mmol·L^-1碳酸氢钠等度淋洗,柱温设为室温,衍生试剂是0．24g·L^-1碘液和0．2％磷酸（V：V）的混合溶液,检测波长为288nm．样品用20mg·L^-1草酸溶液萃取,经高速离心、上层清液过C18预处理小柱及0．45μm过滤膜后直接进样．实验结果表明,方法的检测限硫离子、甲醛合次硫酸氢根离子、亚硫酸根离子、硫氰酸根离子及硫代硫酸根离子分别为0．006,0．004,0．006,0．006和0．007mg·L^-1一天之内的相对标准偏差分别为4．86％,3．24％,3．76％,2．68％和2．07％．实际样品测定,除硫离子外,方法的回收率分布在67．2％～116．5％之间,硫离子的回收率为38％～45％．     

间接荧光检测离子色谱法分析维生素C、亚硫酸根和硫代硫酸根

报道了一种用离子色谱分析维生素Ｃ、亚硫酸根和硫代硫酸根离子的新方法。在这种方法中采用了四价铈柱后氧化还原反应和三价铈荧光检测法。同时也给出了使用这种方法的一些最佳的实验条件。     

还原性负离子的间接荧光检测离子色谱法

采用４个铈柱后反应和３价铈荧光检测的离子色谱法分离维生素Ｃ,亚硝酸根,硫代硫酸根,亚硫酸根,草酸根和碘离子６种还原性负离子,同时也给出了使用这种方法的一些最佳条件。     

Optimization of o‐phtaldialdehyde/2‐mercaptoethanol postcolumn reaction for the hydrophilic interaction liquid chromatography determination of memantine utilizing a silica hydride stationary phase

A rapid procedure for the determination of memantine based on hydrophilic interaction chromatography with fluorescence detection was developed. Fluorescence detection after postcolumn derivatization with o‐phtaldialdehyde/2‐mercaptoethanol was performed at excitation and emission wavelengths of 345 and 450 nm, respectively. The postcolumn reaction conditions such as reaction temperature, derivatization reagent flow rate, and reagents concentration were studied due to steric hindrance of amino group of memantine. The derivatization reaction was applied for the hydrophilic interaction liquid chromatography method which was based on Cogent Silica‐C stationary phase with a mobile phase consisting of a mixture of 10 mmol/L citric acid and 10 mmol/L o‐phosphoric acid (pH 6.0) with acetonitrile using an isocratic composition of 2:8 v/v. The benefit of the reported approach consists in a simple sample pretreatment and a quick and sensitive hydrophilic interaction chromatography method. The developed method was validated in terms of linearity, accuracy, precision, and selectivity according to the International Conference on Harmonisation guidelines. The developed method was successfully applied for the analysis of commercial memantine tablets.     

Stabilization of sulfide and sulfite and ion-pair chromatography of mixtures of sulfide, sulfite, sulfate and thiosulfate

Ion chromatography of sulfide, sulfite, sulfate and thiosulfate in a mixture is often difficult because of instability of sulfide and sulfite, poor separation of sulfide from common anions such as bromide or nitrate and similar elution-times for sulfite and sulfate. An ion-pair chromatographic method for the determination of these sulfur anions has been established by stoichiometric conversion of sulfide and sulfite into stable thiocyanate and sulfate, respectively, prior to the chromatographic run. Sulfate, thiosulfate and thiocyanate were resolved on an octadecylsilica column with an acetonitrile-water mobile phase containing tetrapropylammonium salt (TPA) as an ion-paring reagent, and thiosulfate and thiocyanate in the effluent could be measured with a photometric detector (220 nm) and sulfate with a suppressed conductivity detector. When an acetonitrile-water (6:94, v/v) mobile phase (pH 5.0) containing 15 mM TPA and small amounts of acetic acid was used at a flow-rate of 0.6 ml min(-1), the three anions could be eluted within 32 min. Calibration plots of peak height versus concentration for sulfide (detected as thiocyanate) and thiosulfate gave straight lines up to 35 and 60 microM, respectively. The calibration plot for sulfide coincided with that obtained by using thiocyanate. A calibration plot for sulfite, measured as sulfate, was also linear up to 135 microM and was in accord with that of sulfate. Each calibration plot gave a correlation coefficient greater than 0.999. For six replicates obtained for a mixture of 30.0 microM sulfide, 50.0 microM sulfite, 50.0 microM sulfate and 20.0 microM thiosulfate, the proposed method gave a mean value of 30.1 microM with a standard deviation (SD) of 0.77 microM and a relative standard deviation (RSD) of 2.6% for sulfide, 101 microM (SD = 3.5 microM, RSD = 3.5%) for the total of sulfite and sulfate and 20.1 microM (SD = 0.44 microM, RSD = 2.2%) for thiosulfate. Recoveries for sulfide, sulfite plus sulfate, and thiosulfate in hot-spring water samples using the proposed method were found to be quantitative.     

水中微量硅的硅钼蓝光度法测定——还原剂的研究

研究和配制了一种甲醛合次硫酸氢钠和亚硫酸钠的混合液作为水中微量硅（硅钼蓝）光度法测定的还原剂，其还原能能力、稳定性、准确度均较好，适用于多种水源中微量硅的测定。     

Simultaneous determination of trace amounts of sulfite and thiosulfate in petroleum and its distillates by extraction and differential pulse polarography

Simultaneous determination of sulfite and thiosulfate at sub-ppm levels in petroleum and its distillates was investigated using a convenient, accurate and sensitive procedure. This method involved preliminary extraction of the sample followed by detection via differential pulse polarography (DPP) at a dropping mercury electrode. In this procedure, an appropriate amount of sample was shaken with a recommended volume of 0.25% (w/w) sodium acetate solution. The mixture was filtered in two steps and was then ready for DPP. The method was free from interferences from hydrogen sulfide, elemental sulfur, organic sulfides, and thiophene. Various instrumental factors such as scan rate, pulse height, initial and final potential, and purge time were optimized. The 3σ detection limits were 410 and 125 ng g⁻¹ for sulfite and thiosulfate, respectively. At 5 μg g⁻¹ level in samples, the relative standard deviations (n=4) were 2.51 and 1.15% for sulfite and thiosulfate, respectively. The proposed method was applied to real samples containing input feeds, distillates and fuel oils from Abadan Petroleum Refinery in the south of Iran.     

Electrocatalytic oxidation of thiosulfate at2,7-bis(ferrocenylethyl)-fluoren-9-one-modified carbon paste electrode(2,7-BFEFMCPE): Application to the catalytic determination of thiosulfate in real sample

<正>Electrocatalytic oxidation of thiosulfate at the 2,7-BFEFMCPE occurs at a potential about 460 mV less positive than that unmodified carbon paste electrode.The diffusion coefficient(=5.6×10~(-5) cm~2 s~(-1)),the kinetic parameters such as electron transfer coefficient,(=0.5) and k_h(=1.21×10~(-3) cm s~(-1)) of thiosulfate oxidation at the surface of,2,7-BFEFMCPE were determined.The electrocatalytic oxidation peak current of thiosulfate showed two linear dynamic ranges(0.0006-0.009 mmol/L and 0.009- 0.900 mmol/L) and a detection limit of 0.00015 mmol/L.This method was also examined as a new electrochemical sensor for the determination of thiosulfate in real sample.     

Simultaneous determination of oxalate, thiosulfate, and thiocyanate in urine by ion-exclusion chromatography with electrochemical detection

Summary A sensitive ion-exclusion chromatographic method has been developed for determination of oxalate, thiosulfate, and thiocyanate. The method is based on separation of these anions on a polymethacrylate-based, weakly acidic cation-exchange resin (TSKgel OApak-A) and detection by means of a glassy carbon (GC) electrode electrochemically modified with polyvinylpyridine (PVP), palladium, and iridium oxide (PVP/Pd/IrO₂). The electrochemical behavior of oxalate, thiosulfate, and thiocyanate at this chemically modified electrode (CME) have been investigated by cyclic voltammetry. The results indicated that electrocatalytic oxidation of these anions by the electrode was efficient and that the sensitivity, stability, and lifetime of the electrode were relatively high. Combined with ion-exclusion chromatography the PVP/Pd/IrO₂ electrode was used as the working electrode for amperometric detection of these anions. All linear ranges were over two orders of magnitude and detection limits, defined asS/N=3, were 9.0×10⁻⁷ mol L⁻¹ for oxalate, 6.7×10⁻⁷ mol L⁻¹ for thiosulfate, and 5.6×10⁻⁷ mol L⁻¹ for thiocyanate. Correlation coefficients were all>0.998. Coupled with microdialysis sampling the method has been successfully applied to the determination of oxalate, thiosulfate, and thiocyanate in urine.     

Derivatizing assay for the determination of aldehydes using micellar electrokinetic chromatography

In this work, the use of a novel derivatization agent for the determination of aldehydes (in this particular case: formaldehyde, acetaldehyde, propionaldehyde, and valeraldehyde) using micellar electrokinetic chromatography is reported. The derivatization reaction is based on the reaction of aldehydes with benzhydrazide to form the corresponding derivates with maximum absorbance at 250 nm. The experimental conditions of the derivatization reaction as well of the separation were optimized. The adducts were separated with a +22 kV voltage at a temperature of 29°C. The adducts’ separation was performed in less than 14 min using as the running buffer a mixture containing 110 mmol/L of sodium dodecyl sulfate and 27 mmol/L of sodium tetraborate at pH 9.45. Samples were injected using hydrodynamic mode (50 mbar × 5 s). The calibration curves were linear up to 15.0 mg/L with r ² above 0.99. Intra and inter‐day precisions were in average 3 and 4%, respectively, and recoveries were in average of 95%. Limits of detection and quantification were around 0.5 and 1.5 mg/L, respectively. The developed method was successfully applied in the analysis of low molar weight aldehydes in yogurt and vinegar samples.     

食品中亚硫酸盐的离子色谱法测定

建立了食品中亚硫酸盐的离子色谱检测方法. 样品采用40 mmol/L NaOH溶液提取, 甲醛作稳定剂, 经ENVI-Carb活性碳小柱除去提取液中的色素, 石油醚除去提取液中的油脂, 用配有电导检测器的离子色谱仪测定. 以AS9-HC为色谱柱, 流动相为8 mmol/L Na2CO3-2.5 mmol/L NaOH, 亚硫酸盐的残留量在0～6.0 mg/L的范围内线性关系良好, 相关系数为0.9989, 相对标准偏差为1.3%～9.1%, 回收率在88.4%～98.1%之间.     

Cyclohexane‐1,3‐dione as a derivatizing agent for the analysis of aldehydes by micelar electrokinetic chromatography with diode array detection

Aldehydes are important compounds in a large number of samples, especially food and beverages. In this work, for the first time, cyclohexane‐1,3‐dione (CHD) was used as a derivatizing reagent aiming aldehyde (formaldehyde, acetaldehyde, propionaldehyde, and valeraldehyde) analysis by MEKC‐DAD. The optimized separation of the derivates was performed using a voltage program (+20 kV, 0–15 min.; +23 kV, 15–17 min.) at a temperature of 26°C, and using as the running buffer a mixture containing 100 mmol/L of sodium dodecyl sulfate and 29 mmol/L of sodium tetraborate at pH 9.2, with maximum absorbance at 260 nm. CHD was compared with two other derivatizing agents: 3‐methyl‐2‐benzothiazolinone hydrazone and phenylhydrazine‐4‐sulfonic acid. The CHD‐aldehyde derivatives were also characterized by LC‐MS. The calibration curves for all aldehydes had r² above 0.999 and LODs ranged from 0.01 to 0.7 mg/L. The optimized methodology was applied in sugar cane brandy (cachaça) samples successfully. CHD showed to be an alternative derivatization reagent due to its stability, aqueous solubility, high selectivity and sensitivity, reduced impurities, and simple preparation steps.     

Electrocatalytic sulfite biosensor with human sulfite oxidase co-immobilized with cytochrome c in a polyelectrolyte-containing multilayer

An efficient electrocatalytic biosensor for sulfite detection was developed by co-immobilizing sulfite oxidase and cytochrome c with polyaniline sulfonic acid in a layer-by-layer assembly. QCM, UV–Vis spectroscopy and cyclic voltammetry revealed increasing loading of electrochemically active protein with the formation of multilayers. The sensor operates reagentless at low working potential. A catalytic oxidation current was detected in the presence of sulfite at the modified gold electrode, polarized at +0.1 V (vs. Ag/AgCl 1 M KCl). The stability of the biosensor performance was characterized and optimized. A 17-bilayer electrode has a linear range between 1 and 60 μM sulfite with a sensitivity of 2.19 mA M⁻¹ sulfite and a response time of 2 min. The electrode retained a stable response for 3 days with a serial reproducibility of 3.8% and lost 20% of sensitivity after 5 days of operation. It is possible to store the sensor in a dry state for more than 2 months. The multilayer electrode was used for determination of sulfite in unspiked and spiked samples of red and white wine. The recovery and the specificity of the signals were evaluated for each sample. Figure Schematic of the bioelectrocatalytic sulfite sensor: sulfite oxidase (green) oxidizes sulfite to sulfate and transfers electrons via heme b ₅ to cyt c (red) and thence to the gold electrode     

Ionic liquids as mobile phase additives for determination of thiocyanate and iodide by liquid chromatography

An analytical method was developed for the simultaneous determination of thiocyanate and iodide by reversed‐phase liquid chromatography with UV detection using imidazolium ionic liquids as mobile phase additives. The chromatographic behaviors of the two anions on a C₁₈ column were studied and compared with four types of reagents including imidazolium ionic liquids, pyridinium ionic liquids, 4‐aminophenol hydrochloride and tetrabutylammonium as mobile phase additives. The effects of the concentrations of imidazolium ionic liquids, organic solvents and detection wavelength on separation and detection of the anions were investigated. The role of ionic liquids, retention rules and mechanisms were discussed. The separation of the anions was performed on the C₁₈ reserved‐phase column using acetonitrile‐0.3 mmol/L 1‐amyl‐3‐methylimidazolium tetrafluoroborate (10:90, v/v) as mobile phase, with column temperature of 35°C, flow rate of 1 mL/min and detection wavelength of 210 nm. Under these conditions, the two anions can be completely separated within 6 min. The limits of detection were 0.05 mg/L. The method was applied for the determination of thiocyanate and iodide in ionic liquid samples and iodide drugs, and the spiked recoveries ranged from 97 to 101%. The method is simple, accurate and meets the requirements of quantitative analysis for thiocyanate and iodide.     

Determination of sulfite in water samples by flow injection analysis with fluorescence detection

<正>A fast,sensitive,and reliable method for the determination of sulfite(SO_3~(2-)) in fresh water and seawater samples was developed.The proposed method was based on the reaction of o-phthalaldehyde(OPA)-sulfite-NH_3 in alkaline solution,with flow injection analysis and fluorescence detection.The experimental parameters were investigated in pure water and seawater matrixes. The detection limits(S/N = 3) were 0.006μmol/L in pure water and 0.018μmol/L in seawater for SO_3~(2-).The method was successfully applied to analyze SO_3~(2-) in the samples of rain water and flue gas desulfurization seawater.     

Field-amplified sample injection combined with pressure-assisted capillary electrophoresis UV detection for the simultaneous analysis of allantoin, uric acid, and malondialdehyde in human plasma

The allantoin/uric acid (All/UA) ratio and malondialdehyde (MDA) plasma levels have been proposed as important markers for monitoring oxidation triggered by the action of free radicals (FR). Here, we describe an easy field amplified sample injection capillary electrophoresis method with UV detection for the separation and quantification of All, UA, and free MDA in human plasma. The plasma samples were simply filtered through centrifugation membrane tubes for protein elimination and directly injected on a capillary without complex cleanup and/or sample derivatization procedures. The use of a run buffer composed of 300 mmol/L sodium borate at pH 10 with 50 mmol/L of N-methyl-d-glucamine and an overimposed pressure/voltage of 0.1 psi during the electrophoretic run allows basline resolution of the analytes within 17 min. The electrokinetic injection allows a detection limit of 15 nmol/L for All, 20 nmol/L for UA and 10 nmol/L for MDA in a plasma sample, thus significantly improving the LOD of previous described methods based on capillary electrophoresis. Precision tests indicate a good repeatability of our method both for migration times (CV = 1.85%) and areas (CV = 2.87%). Moreover, a good reproducibility of intra- and inter-assay tests was obtained (CV = 4.63% and CV = 6.59% respectively). The suitability of the method was tested by measuring analyte levels in 40 healthy volunteers.     

Determination of methyl methanesulfonate and ethyl methanesulfonate in methanesulfonic acid by derivatization followed by high‐performance liquid chromatography with ultraviolet detection

Methanesulfonic acid is routinely used in pharmaceuticals but can contain potentially genotoxic impurities such as methyl methanesulfonate and ethyl methanesulfonate. The aim of this study was to develop a simple high‐performance liquid chromatography with ultraviolet detection method for determining methyl methanesulfonate and ethyl methanesulfonate in methanesulfonic acid. Samples (250 mg) in water/acetonitrile (200 μL) were first combined with 10.0 mol/L sodium hydroxide solution (270 μL). Then they were mixed with 2.0 mg/mL N ,N‐diethyldithiocarbamate (500 μL), diluted to 5 mL with N ,N‐dimethylacetamide and allowed to react at 80°C for 1 h. The derivatives were analyzed using gradient high‐performance liquid chromatography with ultraviolet detection (277 nm) and structurally elucidated by liquid chromatography with mass spectrometry. With acetonitrile/5 mmol/L ammonium acetate solution as the eluent and 1 mL/min as the flow rate on a C18 column, the derivatives were eluted at 10.6 and 14.8 min. Good linearity (correlation coefficients > 0.999) and low limits of quantitation (0.6 ppm) were obtained. The recoveries were in the range of 80–115% with relative standard deviation < 5.0%. Finally, the established method was successfully used for the determination of methyl methanesulfonate and ethyl methanesulfonate in methanesulfonic acid.     

阴离子交换色谱法测定硫磺熏制姜中亚硫酸盐

建立了阴离子交换色谱分离、抑制型电导检测分析硫磺熏制生姜(简称硫磺姜)中亚硫酸盐的方法。使用NJ-SA-4A阴离子交换分析柱,淋洗液为1.92mmol/L Na2CO3-1.80mmol/L NaHCO3-2%(体积分数)丙酮。通过在样品提取液中加入三乙醇胺,有效地维持了亚硫酸盐的稳定性、并能提高方法的选择性。SO23-在0.02～2.00mg/L范围内线性良好,相关系数为0.9998,峰面积的相对标准偏差为1.9%。方法的检出限为0.015mg/L,加标回收率为84.0%～93.5%。该方法为生姜的市场监测提供了有效的方法。     

Baseline separation of α and β‐acids homologues and isomers in hop (Humulus lupulus L.) by CD‐MEKC‐UV

An alternative method for simultaneous baseline separation of α and β‐acids homologues and isomers in hop by CD‐MEKC with UV detection was proposed. The optimized background electrolyte was composed of 30 mmol/L sodium tetraborate solution, 45 mmol/L sodium dodecyl sulfate, 20 mmol/L β‐cyclodextrin and 10% v/v acetonitrile. The instrumental conditions were evaluated by using a 3³ Box‐Benhken experimental design. In order to demonstrate the applicability of the method, 21 hop samples from different varieties were analyzed. The repeatability intra‐ and interday tests were performed and relative standard deviations lower than 7% for area and migration times were observed. The present method comprehended 8 min analysis time and revealed to be faster and more efficient when compared to previous reports from literature.     

Analysis of Total Non-Volatile Non-Sulfide Reduced Sulfur in Potable and Untreated Surface and Groundwaters

Abstract

An analytical method was developed to measure the total concentration of non-volatile non-sulfide reduced sulfur in treated and untreated surface and groundwater. The method was based on the alkaline reduction by Raney nickel (prepared in situ from Raney alloy) of organic and inorganic sulfur compounds (in oxidation states below +6) to sulfide. Sulfide was swept out of the reflux apparatus under nitrogen into a trap of zinc acetate and determined colorimetrically as ethylene blue. The recoveries obtained from solutions of elemental sulfur, sulfide, sulfite, thiosulfate, tetrathionate, cysteine, cystine, methionine, glutathione, allylthiourea, sulfanilamide and thiocyanate ranged from 84–102% with typical recoveries of approximately 90%. Sulfate was not detectable by the procedure. Chlorine present in potable water samples interfered in the procedure and was removed with sodium borohydride. The relative standard deviation of the method varied from 0.25 to 5.6% and averaged 3%. The detection limit based on a 500 mL sample was 3 mg m^?3.