Numerical analysis of polarization character in Yb~(3+)-doped fiber amplifiers

Polarization-dependent gain (PDG) and state of polarization (SOP) of the output signal light in Yb3+-doped fiber amplifiers are studied by numerically stimulation, which showed that PDG of output signal light is not only changed with the input pump power and signal power, input polarization of pump and signal light, but also changed with the doping concentration, the cross-section anisotropy, the fiber length, the phase difference of the fiber, and so on. Moreover, SOP of the output signal light is studied. It is found that the polarization of output signal light is relative not only to the phase difference of the fiber, polarization of pump and signal light as the non-doped fiber, but also to PDG of output signal light, the cross-section anisotropy, the doping concentration, and so on, which is different to the non-doped fiber.     

Polarization dependence of gain and amplified spontaneous Brillouin scattering noise analysis for fiber Brillouin amplifier

The polarization dependences of gain and amplified spontaneous Brillouin scattering(ABS) noise for fiber Brillouin amplifier(FBA) are analyzed through theories, simulations, and experiments.Modified vector propagation equations for calculating the gain of the probe signal and the ABS noise are derived and analyzed in the Stokes spaces.In simulations and experiments, we prove that the gain of the probe signal and the ABS noise are strongly dependent on the relative state of polarization(SOP) of the pump and probe signals.The closer the relative SOP of the pump and probe signals is, the more obvious ABS noise suppression effect will be brought by increasing the power of the input probe signal.     

掺铒光纤非线性耦合器的实验研究

提出一种耦合参量可用光调控的掺铒光纤非线性耦合器.用熔融拉锥法熔合两根掺铒光纤,拉制成工作波长为155nm的3dB掺铒光纤耦合器.通过调变输入耦合器一臂的980nm泵浦光功率,可以改变两臂的传播常量差,从而改变耦合器两臂信号光的相对输出功率.通过测量输入泵浦光功率和两臂信号光输出功率,得到直通臂耦合比依赖于泵浦光功率的实验曲线.实验研究表明,当泵浦光功率从0 mW变化至20 mW时,耦合比的变化可达到40％.与理论模拟的结果一致.     

Characterization of cross-polarization modulation on a two channel WDM system

This article contributes experimental corroboration of cross-polarization modulation (XPolM). A continuous wave probe signal is remotely controlled by a modulated pump signal. Experimental results show that the state of polarization (SOP) evolution of the probe signal resembles that of the pump signal to a confined region on the Poincaré sphere. Further a bit pattern is transmitted on the probe signal by making use of cross-phase modulation induced nonlinear polarization rotation of the probe signal. The article also gives evidence to the detrimental effect cross phase modulation may have on polarization mode dispersion compensators. The results show that the degree of polarization degradation of a probe signal in a two model wavelength division multiplexing system deteriorates with an increase in the power ratio between the pump and probe signal.     

Kerr nonlinear switch based on ultra-compact photonic crystal directional coupler

In this paper, an all optical switch based on nonlinear photonic crystal directional coupler has been simulated and analyzed by the finite difference time domain (FDTD) method. The lunched pump signal increases the refractive indices of the central row of the coupler, due to nonlinear Kerr effect, hence the coupler works in the nonlinear conditions and lightwave guides to the other output port. We have tried to increase the coupling efficiency and reduce the required power in the nonlinear status by optimizing the bends structure and increasing the interaction between dielectric and lightwave signal. Therefore, the input signal beam can be controlled to be exchanged between two output ports to earn the highest output power ratio and the smallest amount of power required for nonlinear performance, the physical length of the coupler is determined to be 20a, where a is the structure lattice constant.     

Optical-frequency balanced mixer

Optical signal processing devices based on quasi-phase-matched three-wave mixing and cascaded three-wave mixing in guided-wave geometries have been demonstrated to operate efficiently at practical pump-power levels. We describe operation of such devices in a balanced mode that allows mixing without wavelength offset and separation of mixed output from pump and signal input without wavelength-selective filters. We present a design for an optical-frequency balanced mixer using quasi-phase-matched, cascaded second-order nonlinear processes. Using this design, we fabricated a balanced mixer in periodically poled lithium niobate waveguides that has the expected linear and nonlinear optical performance.     

Phase noise generation in an amplitude limiter using saturation of a fiber-optic parametric amplifier

Generation of phase noise in an amplitude limiter using saturation of a fiber-optic parametric amplifier is analyzed. The analysis is based on the coupled differential equations for the amplitudes and phases of pump, signal, and idler involved in the four-wave mixing interaction. The equations are linearized about small fluctuations at operation points and are solved, which results in relations between the input and output phase and amplitude noise. These relations are used in deriving expressions of amplitude signal-to-noise ratio (SNR) and variance of phase noise of the output signal in terms of SNRs of input signal and pump. It is shown that optimum pump power exists for minimum output phase noise in the output signal.     

The on-off contrast in an all optical switch based on stimulated Raman scattering in optical fibers

We present the investigation of the ON-OFF contrast in an optical switch using stimulated Raman Scattering in optical fibers. The setup consists of a Raman circuit of two fiber stages connected in series with a spectral filter rejecting the signal inserted between them. The stage 1 works as saturated amplifier, in this stage the pump pulses are saturated when pump and signal are launched to the input or travel through the fiber without saturation when pump only is launched at the input. The stage 2 works as a Raman amplifier with amplification depending on the pump power entering from the first stage. When pump only is launched at the input enter to the second stage without saturation and amplifies the signal entering this stage, strong signal pulses appear at the output; when pump and signal are launched to the input the pump is saturated in the first stage and the filter rejected the amplified signal, so that only low power pump enters the second stage and no signal pulses appear at the output. We use 2 ns pump pulses at 1528 nm and continuous-wave signal at 1620 nm. In the first stage of Raman circuit, we use both fibers with normal and anomalous dispersion. In fibers with anomalous dispersion, pump saturation is affected by modulation instability. We find that the contrast may be improved using fibers with normal and anomalous dispersion connected in series in the first stage, provided there is appropriate selection of their lengths. The best achieved contrast was 15 dB at 6 W pump peak power.     

延迟-非线性反馈控制混沌

提出了基于稳定性准则的延迟非线性反馈控制混沌的方法，即SC延迟非线性反馈控制法. 通过对混沌系统的适当分离，得到一个特殊的非线性函数，并利用混沌输出信号与其延迟信号的非线性函数的差，构造了连续反馈输入干扰，以控制混沌轨到某一期望的不稳周期轨上. 该方法继承了延迟反馈控制方法的优点，实现了自-控制过程. 另外由于该方法基于线性系统的稳定性准则，保证了控制的有效性. 控制过程可随时开始，具有简便、灵活性. 给出耦合Duffing振子的例子，数值模拟结果显示了SC延迟反馈方法控制的有效性. 关键词： 稳定性准则 混沌控制 延迟反馈 干扰     

基于光纤四波混频效应的新型组播方法

组播是波长路由光通信网络中的一项重要功能.提出并实验实现了基于高非线性光纤四波混频效应的全光组播方法,将一束载有数据的输入信号光和一束抽运光一起入射到一段高非线性光纤中,通过两个简并四波混频过程产生了两个携带该数据信息的闲频光,从而实现了单一信号的两信道组播,同时抽运光也会受到数据信息的调制.该方法的优点在于组播的实现只需要单一的抽运光源,而不需要再提供其他输入光,结构简单,组播光信号功率均匀、波长可调,并且具有进一步增加组播信道的能力. 关键词： 组播 四波混频 高非线性光纤     

Several hundred kHz repetition rate nanosecond pulses amplification in Er–Yb co-doped fiber amplifier

We have experimentally investigated several hundred kHz repetition rate 1,550-nm nanosecond pulses amplification in Er–Yb co-doped fiber amplifier (EYDFA). The experimental setup has three stage fiber amplifiers. At the output of the second stage EYDFA, Yb³⁺ ions induced amplified spontaneous emission (Yb-ASE) is not observed owing to the low pump power. In the third stage EYDFA, a simultaneously seeded 1,064-nm continuous-wave laser is used to control Yb-ASE. Without any additional 1,064-nm signal, significantly backward Yb-ASE which caused loss-induced heat accumulation at the input port of the pump combiner can be observed. The monitored temperature at the input port of the pump combiner rapidly grows from 30 to 80 °C when the pump power is turned from 20 to 32 W. When a 196-mW forward 1,064-nm laser is added, the monitored backward Yb-ASE power is significantly declined, and the monitored temperature is kept below 35 °C. But, the additional signal caused a large power fraction at 1,064 nm in the output laser. In our experiment at the maximum pump power of 48.5 W, the total output power is 20 W with ~6.4-W 1,550-nm pulsed laser and ~13-W 1,064-nm continuous-wave laser.     

Polarization insensitive wavelength multicasting of DPSK signal using four-wave mixing in a birefringent photonic crystal fiber

We demonstrate polarization-insensitive wavelength multicasting of differential phase-shift keying (DPSK) signal based on four-wave mixing (FWM) in a highly nonlinear, birefringent photonic crystal fiber (PCF). The 10-Gbit/s RZ-DPSK input signal is copied to 8 wavelength channels through FWM with three optical pumps. The pump wavelengths are unequally spaced to avoid undesirable crosstalk from pump-to-pump beatings. The dependence of conversion efficiency on input signal polarization is suppressed by exploiting the PCF birefringence together with control of the pump polarizations. All pump polarizations are aligned at 45 degrees to the principal axes of the PCF. Open eyes and error-free results are obtained in all the 8 multicast channels for polarization-scrambled RZ-DPSK input signal.     

Passive mode locking of fiber lasers upon doubling the period of repetition of ultrashort pulses in the output radiation

The dynamics of the output radiation of fiber lasers with nonlinear losses caused by an intracavity polarizer and by nonlinear optical activity due to the Kerr nonlinearity of the fiber is studied by numerical simulation. It is shown that the model of lasing that takes into account the concentration of nonlinear losses in the intracavity polarizer describes the characteristic transient regimes of the passive mode locking, connected with a nonstationarity of the parameters of the output radiation: doubling of the period of repetition of the field structure in the output radiation, appearance of slow periodic changes of the parameters of light pulses in the regimes with the doubled period, and transitions to the regimes with chaotic change of the characteristics of ultrashort pulses.     

中红外连续波单谐振光学参量振荡器热致相位失配

为了研究热致相位失配对中红外连续波单谐振光学参量振荡器(CW-SRO)输出效率的影响, 结合CW-SRO计算模型和热传导方程,利用有限元分析方法,重点对输出3.3 m波长闲频光的CW-SRO进行了分析。计算了不同信号光输出耦合率及不同泵浦功率下CW-SRO晶体输出截面上热致相位失配量的分布。由计算结果可以看出：晶体吸收腔中振荡信号光是导致晶体热效应的主要因素;在相同的输入条件下,泵浦功率在30 W以上时CW-SRO的热致相位失配将会大大降低其泵浦损耗率;通过增加信号光输出耦合率的方法,可以减少热致相位失配对CW-SRO输出效率的影响,但CW-SRO的振荡阈值会增加。     

Signal design using nonlinear oscillators and evolutionary algorithms: application to phase-locked loop disruption

This work describes an approach for efficiently shaping the response characteristics of a fixed dynamical system by forcing with a designed input. We obtain improved inputs by using an evolutionary algorithm to search a space of possible waveforms generated by a set of nonlinear, ordinary differential equations (ODEs). Good solutions are those that result in a desired system response subject to some input efficiency constraint, such as signal power. In particular, we seek to find inputs that best disrupt a phase-locked loop (PLL). Three sets of nonlinear ODEs are investigated and found to have different disruption capabilities against a model PLL. These differences are explored and implications for their use as input signal models are discussed. The PLL was chosen here as an archetypal example but the approach has broad applicability to any input∕output system for which a desired input cannot be obtained analytically.     

半周期延迟-非线性反馈控制混沌

提出了基于稳定性准则的半周期延迟-非线性反馈控制混沌的方法，即SC(stability criterion)半周期延迟非线性反馈控制法.通过对混沌系统的适当分离，得到一个特殊的非线性函数，并利用混沌输出信号与其半周期延迟信号的非线性函数之和，构造了连续反馈输入干扰.该方法继承了延迟反馈控制方法及稳定性准则控制方法的优点，实现了有效的自控制过程；并克服了延迟反馈方法的限制，能将嵌入混沌吸引子中的自对称直接不稳周期轨稳定.控制过程可随时开始，具有简便、灵活性.数值模拟结果显示了SC半周期延迟-非线性反馈方法控制的有效性. 关键词： 稳定性准则 混沌控制 半周期延迟 非线性反馈     

中红外连续波单谐振光学参量振荡器热致相位失配

为了研究热致相位失配对中红外连续波单谐振光学参量振荡器(CW-SRO)输出效率的影响, 结合CW-SRO计算模型和热传导方程,利用有限元分析方法,重点对输出3.3 m波长闲频光的CW-SRO进行了分析。计算了不同信号光输出耦合率及不同泵浦功率下CW-SRO晶体输出截面上热致相位失配量的分布。由计算结果可以看出:晶体吸收腔中振荡信号光是导致晶体热效应的主要因素;在相同的输入条件下,泵浦功率在30 W以上时CW-SRO的热致相位失配将会大大降低其泵浦损耗率;通过增加信号光输出耦合率的方法,可以减少热致相位失配对CW-SRO输出效率的影响,但CW-SRO的振荡阈值会增加。     

DCM中C_3H_6O受激拉曼散射荧光增强特性

本文报道了DCM增强C3H6O受激拉曼散射荧光增强特性研究结果。实验测量了在不同的DCM浓度、不同的泵浦激光强度以及不同的Stokes入射信号条件下Stokes波输出能量,发现当DCM浓度为2×10-4mol/L时,Stokes波最大增强因子达到5.7,Stokes强度随入射激光增强而增强,过强的Stokes输入信号则可能导致Stokes波增益饱和。     

Phenomenological model analysis for semiconductor optical amplifiers and application to time-domain digital polarization encoding

We propose and demonstrate that semiconductor optical amplifiers (SOAs) for each wavelength of the input can be described by a lumped-elements sequence of a partly linear polarizer and a retarder followed by a polarization-independent amplifier, and further obtain two necessary conditions for the valuable orthogonal polarization rotation (OPR), which will be instructive for SOA-based all-optical signal processing. Subsequently we implement photoinduced OPR by controlling an ~2.5 mW pump laser and find the optimal pump wavelength should be an ~0.4 nm interval around the central wavelength of the probe laser. Therefore we propose a time-domain digital polarization encoding scheme based on photoinduced OPR with cross-gain modulation in a SOA and perform it well in a 15 km single-mode-fiber system at 2.5 Gbits/s, which is applicable to optical-power-equalized fiber communication.     

光子晶体光纤中交叉相位调制光谱展宽特性研究

实验研究了超高速时分复用信号与探测光同向传输,在色散平坦高非线性光子晶体光纤中的交叉相位调制光谱展宽特性,从光谱学的角度分析了信号光波长漂移,泵浦光与信号光总功率及功率比,二者偏振态失配对交叉相位调制光谱展宽效应的影响,探讨了实现偏振不敏感交叉相位调制效应的可行性。研究发现,在36 nm波长范围,总功率大于23 dBm,泵浦光与信号光功率比合理,二者偏振态匹配时交叉相位调制效果最好,交叉相位调制的偏振相关性为11 dB,指出利用色散平坦高非线性光子晶体光纤中的残余双折射,调节泵浦光与光纤双折射主轴成45°,可以实现偏振不敏感交叉相位调制效应,随后的理论模拟和实验结果相一致。研究结果为实现基于交叉相位调制原理工作的超快全光信号处理器件作了充分准备。